Search Documents

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

Jan 1, 1977

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By Thomas Watson

INTRODUCTION THE users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the .material in that region. The domestic production is derived from Missouri and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral.

Jan 2, 1915

By L. D. Lash, J. R. Ross

Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per lb which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the US. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold.

Jan 8, 1961

By Charles E. Johnston

The haulage system at the International Minerals T & Chemical Corp. (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC's potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad. From three levels, the 800-ft, 850-ft and 900-ft, over 60 million tons have been extracted. Langbeinite (K,SO,. 2MgS0,) is mined on the 850 level and sylvite (KCl) on the 900 level. The 800 level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to more than 10 ft. A room and pillar mining system is used.

Jan 3, 1963

By J. O. Whitely

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By J. O. Whiteley

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By Charles J. Haas

The effectiveness of rock bolts in resisting shear displacement along preexisting fracture surfaces or slip planes was determined in the laboratory with full-scale bolts and large-scale shear test equipment. The system variables were the type of bolt, orientation of bolt relative to shear surface, and normal pressure on the interface. Results showed that, in general, both conventional bolts and resin- grouted reinforcing bars significantly increase the shear resistance along a fracture or bedding plane when the average normal compressive stress on the plane is in the order of 25 psi and when the bolt is oriented such that it tends to lengthen as the shear progresses. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented such that they lose tension as shear displacement occurs added no shear resistance since the tension drops to zero at very small shear displacements.

Jan 1, 1977

By William Kobbé

I. INTRODUCTION THE word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. II. DRILLING DETERMINING FACTORS IN SELECTION OF METHOD The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well.

Jan 12, 1916

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

By Robert Warner

The growing importance of screening makes an accurate measure of the quality of a sizing operation desirable. Screen efficiency is considered equal to the percentage of true undersize in the feed obtained as undersize from the screen. This method is unreliable, as it gives the same credit for removing minus 200-mesh material as for removing material just able to pass the aperature of the screen. A more accurate measure of screen efficiency is to consider only the work done on the "difficult" grains, that is, those grains of which the intermediate diameters closely approach the screen aperture.. The application of this method is given, together with the derivation of formulas and an example of their use. Is AN accurate measurement of the efficiency of a screen under a given set of operating conditions valuable? If so, what is the efficiency; of, a screen and how can it be measured? Sizing, especially of the finer sizes of material, has increased in importance in the development of flow sheets as a result of the perfecting of the rapid vibrating screens. More consideration should be given screens in the preparation of ball-mill feed, where they permit the admission of a dryer feed than, the classifier. Where possible, the introduction of a screen ahead of the primary ball-mill, and the diverting of ore below, say, 4 mm. to a secondary mill, might result in a greater overall economy because of the thicker feed and the better, adjustment of crushing media and mill operation to the reduction demanded. With the present trend back toward a combination of gravity methods and flotation, rather than flotation alone, the accurate, economical sizing possible with the new screens makes fine jigging a method to be considered. W. 0. Borcherdt1 and John Bland2 discuss the screening problem and also the value of close sizing in the concentration of some of the rare-metal ores. If a screen is to be used, it should be selected in competition with others; other things being equal, that screen which makes the cleanest oversize should be preferred. The quality of the screening and the tons

Jan 1, 1924

By H. C. George

With a growth of 718 per cent in the petroleum industry from 1901 to 1931, there was a corresponding increase in the demand for technically trained men in the industry. This was first met by increasing numbers of college graduates from the old established courses in chemistry, geology and engineering. However, a need began to be felt for scientists and engineers specially trained for the petroleum industry. In 1912 the University of Pittsburgh established the first department in any university in the world that offered major work in petroleum engineering and petroleum geology. In Europe, the first major work in petroleum engineering was offered in England in 1913 at the University of Birmingham. The University of California and Stanford University offered major work in petroleum engineering in 1915. Since that time at least 10 other American universities and colleges have offered major work and at least 12 others are now offering some courses dealing with petroleum and the petroleum industry.

Jan 1, 1934

By Alan U. Seybolt

UNLIKE its sister elements, columbium (niobium) and tantalum, vanadium has not been available until recently in fabricated form. While Vanadium Corporation of America has offered the metal in fairly pure form for sale for many years in small lots for research purposes, this grade of vanadium has been brittle, probably because of a high oxygen content. Hence, when in 1950 the announcement1 was made that wrought vanadium was available as a commercial material, this represented a large step forward in the metallurgy of vanadium. While vanadium is generally regarded as a rare metal, data on its occurrence in the earth's crust show it to be as abundant as copper, zinc, and lead combined. Vanadium is widely distributed, but it does not seem to occur in massive deposits except in a few localities, principally in Colorado, Utah, and Arizona, where it is found in sandstone formations, and in Mina Ragra, Peru. Only in Colorado or Peru are ores mined solely for the vanadium content. Ores in the United States are principally carnotite and roscoelite; the former is of particular interest because of its uranium content. It is a uranium-potassium vanadate containing approximately 52 pct of UO2 and 18 pct of V2O5. Production in the United States during the war years averaged around 2000 tons a year, but dropped to 636 tons in 1946. In recent years, ferrovanadium has been selling for about $2.80 per pound of contained vanadium. This suggests that the price of the pure metal will never be as low as $2.80 per pound, but it could

Jan 1, 1953

By John Edgar, Eugene P. Pfleider

Breakage of rock in mining operations as a part of the overall comminution process is examined. Examples of blasting practice are examined, and the energy expended is related to the comminution work accomplished. Costs for the comminution effected are examined, and an attempt is made to evaluate overall mining practice to determine the range of incremental costs for breaking the ore to a finer size in the mining step.

Jan 1, 1973

By Allan Gibb

The ores of copper are usually associated with minerals containing arsenic, antimony and bismuth. Whatever the means adopted for extracting the copper, these metals are usually found, to a greater or less extent, in the product. There is, however, usually some elimination in the various metallurgical operations to which the ores are subjected, and some attempt is made here to determine the degree to which this elimination is effected.

Jan 1, 1903

By J. L. McK. Yardley

There are two general classes of problems in connection with electric furnaces. First, those relating to the best utilization of the electrical power inside the furnace; second, those connected with the bringing of the electrical power to the point where it is to be utilized. Referring particularly to the latter class of problems, many calculations have been made, covering a wide variety of furnaces, to check the electrical capacity and power factor found from test. The following analysis, made for the purpose of determining the maximum capacity and approximate performance of a new furnace, to operate at 160 volts on a 60-cycle circuit, may be of interest. The first characteristic necessary to determine is the inductance, since this is the factor that limits the amount of power which can be put into the furnace. Inductance is calculated from the dimensions of the furnace, according to formulas of the U. S. Bureau of Standardsll as follows. Formula 99, for mutual inductance, is: M = 2l [log 2l/d-1 +d/l] Formula 103, for self-inductance, is: Both of these formulas are approximations which are nearly correct when 1 is great compared to d or R. 1 = length of circuit, in centimeters, d = separation between the conductors, in centimeters, R = geometric mean radius of conductors. For a circular tube, R = the radius of the circle. For a solid circular conductor, R = 0.7788 X the radius of the conductor. For a rectangular conductor, R = 0.2235 X (a + b), a being the length, and b being the width of the rectangle. To calculate the inductance of a three-phase circuit, it is customary to figure the inductance of one leg. In circuits where the three conductors

Jan 1, 1920

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Two metallurgical chemists for permanent positions in Siberia; one man to have charge of laboratory dealing with the products of a mill working silver-lead-zinc ores, the other to have charge of laboratory in connection with smelting these products. Established camp; living conditions and climate good. Married men preferred. No. 57. An electro-metallurgist for small zinc plant now under construction. Moderate salary to start but likelihood of substantial increase if plant proves successful. No. 58. Assistant engineer in office of consulting engineer for large mining and smelting company. Man desired with technical education and broad experience in mechanical line in connection with mining and smelting operations, capable of taking charge of office and drafting room. No. 59.

Jan 1, 1916