Search Documents

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana's gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author's company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By K. E. Brown, F. W. Jessen

By utilizing an 8,000-ft experimental field well equipped with 10 gas-lift valves and 10 Maihak pressure recorders, gas-lift tests were conducted with port sizes ranging from 5/16 through I in. The well was equipped to provide accurate means of measuring surface pressures, temperatures, quantity of injection gas and fluid production. The tests were conducted in 2%-in. OD tubing, and the well was making 95 per cent water. A complete evaluation of gas-lift-valve port sizes shows the relationship of per cent recovery, gas-liquid ratios, minimum pressure created at the operating valve and horsepower requirements for each port. The length of time necessary for the fluid in the tubing to reach equilib.rium conditions after each cycle was recorded. Fallback of fluid at depths of 477, 969, 1,685, 2,493 and 4,290 ft was noted. For each port size, pressure loads of 2.50, 300, 350, 400 and 450 psi were lifted with a valve operating at approximately 550 psi at 6,000 ft. Gas-liquid ratios for each load were varied from excess gas to a gas volume per cycle whereby the load failed to reach the surface. Numerous curves are presented in evaluating the accumulated dara. The results show a 1-in. port to be the most efficient under all conditions. The production of intermittent liquid slugs against different-sized surface chokes was evaluated. These tests were conducted from a 7/16-in. ported valve at 4,072 ft. Tests indicate that, when possible, a %-in. in diameter choke or larger should be used at the surface. In the past few years most of the advancement in gas-lift operations has been made in continuous-flow operations. Yet, it is estimated that at least 70 per cent of the wells on gas lift in the United States are of the intermittent type. Since the term "slug flow" is sometimes used in both intermittent- and continuous-flow operations, it would be well to distinguish between the two types of flow. Continuous-flow gas lift is defined as a method whereby the fluids are produced at a continuous rate at the surface. This generally requires a continuous injection of gas through a surface choke; however, various other control devices sometimes are installed to eliminate freezing, to shut-off gas during natural flow periods, etc. The actual flow of fluids in the tubing may be of the slug type (one of many flow patterns known to exist in continuous flow). Intermittent flow is defined as a method of gas lift whereby the liquid is produced in separate piston-type slugs. Perhaps this type of flow could best be thought of as a ballistic-type flow where the liquid leaves bottom as a piston, propelled by a slug of expanding gas. Gas generally is injected through some type of control at the surface at predetermined intervals. However, the valve may have characteristics whereby gas can be injected through a small choke and still result in a ballistic-type flow. The purpose of the experimental work was to evaluate the most efficient port size to be used on the operating valve for the ballistic type of lift and, in addition, to establish the importance of utilizing a surface choke large enough to allow slugs to be produced without detrimental effects. This work is part of a compre- hensive study of both intermittent-and continuous-flow gas lift, representing a joint project conducted by the Ohio Oil Co., the Sun Oil Co., Otis Engineering Corp, and The U. of Texas. The problem of evaluating port sizes has been given little previous attention. Some work undoubtedly has been done which has not been published to date. Some tests were conducted when the wireline, mechanically-opened valve (Nixon) first came on the market. This valve was capable of utilizing full tubing area as its port size. It is known that this was a very efficient valve, but to the authors' knowledge the results of tests have never been published. EXPERIMENTAL EQUIPMENT These tests were conducted on an actual field well, the Ohio-Sun Unit Well No. 2-E, in the North Markham-North Bay City field, Matagorda County, Tex. The well incorporated 23/8-in. OD tubing and produced 95 per cent water. Since the running of equipment was to be quite elaborate and expensive, a well was selected in which both intermittent- and continuous-flow tests could be conducted. This particular well was capable of producing in excess of 1,000 B/D of liquid (95 per cent salt water), yet with a 3/64-in. in diameter bottom-hole choke, production was controlled to 82 B/D. Most of the intermittent tests were conducted at this low rate. Figs. 1 and 2 show all the surface and down-hole equipment. As can be seen, every attempt was made to insure that ample equipment was available for reliable testing procedures. Fig. 1 shows the surface testing equipment. The input gas was controlled first by a regulator, then

By Norman F. Schulz

Relative fineness is an important characteristic of iron ore balling feeds. It is frequently expressed in terms of the Blaine Number which is determined by standardized permeametry procedures. Inconsistencies in Blaine Number specifications for balling feeds from different sources prompted an investigation of permeability methods. A revised procedure for permeametry tests was developed for use with conventional apparatus that yields an Effective Blaine Number which is similar to the Standard Blaine Number except that it more accurately describes the effective fineness of the actual test sample.

Jan 1, 1980

By G. H. LeFevre

THE Metal Sales Department, with offices in New York, is responsible for the sale of the Company's products, with the exception of gold and coal. At present the department handles the sales of lead, zinc, silver, antimonial lead, , cadmium, bismuth, arsenic trioxide, and tellurium; gold is shipped direct to the United States Mint and coal is marketed by United States Fuel Company's own sales organization. The department keeps in close touch with the metal markets and collects information on marketing conditions, which it makes available to other departments of the Company. The electrolytic lead produced at the U. S. S. Lead Refinery, Inc., is a high-uality product marketed as corroding grade under the "U. S. S.-ELECTRO" brand. It is largely sold to manufacturers of paints, pigments, lead oxides, and storage batteries.

Jan 1, 1948

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By C. E. Nighman, R. S. Foster

The following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. , This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running— the power having been cut off shortly after the outbreak of the fire—the air shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to be drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast, as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned back and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the pall of smoke to the main shaft were saved. There were 220 men in the mine that night, and all but 25 were hoisted to the surface within 30 min. after the discovery of the fire. Of the 25, five went out through the Tramway mine, and one through the Moun-

Jan 1, 1918

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937

By G. N. Goldberg, Robert A. Rapp

The steady-state kinetics and microstructures of simultaneous internal oxidation and external scale formation were investigated for the oxidation of Cb-Zr and Ch-Zr-Re alloys in pure oxygen at 1000°C. For each binary alloy, a constant rate of scale formation was observed at steady state; the internal oxidatton zone reached a steady-state, time-independent thickness. The dependence of the scaling rate on zirconium content exhibited a maximum at a low zirconium colttent; more concentrated alloys oxidized at a slower rate than pure columbium. This composition dependence of the scaling rate may be partially attributed to the effect of the internal oxidation process as an intenla1 sink for oxygen, with the formation of voluminous, and relatively impermeable ZrO2 precipitates. However, the morphologies of the ZrO2 internal oxide precipitates also affected the scaling rate. The internal oxide precipitates were distributed uniformly in the external scale. The steady-state thicknesses of the internal oxidation zones were not in agreement with those predicted theoretically from an idealized simple model. However, in this particular alloy systen1 the ideal model is not satisfied experitmentally. For ternary Cb- Zr - Re alloys with Nr10e = 0.02 or 0.05, the steady-state thicknesses of the internal oxidation zones were less than those for the corresponding binary Cb-Zr alloys. For ternary alloys with NRe(0) - 0.05, a more adherent and much less porous external scale was formed, and a reduction in the kinetics of scale formation was observed. A number of authors'-7 have reported linear oxidation kinetics for the reaction of pure columbium at 1000°C in air or in oxygen of about 1 atm pressure. A thin and tightly adherent oxide layer is found at the metal/oxide interface beneath a porous external layer of scale. Although the suboxides CbO and CbO2 represent thermodynamically stable phases at 100O°C, generally only Cb2O5* is identified as a reaction product in quenched specimens. Studies at 1000°C at lower oxygen pressures8,10 (Po2 - 10-4 Torr) show that both CbO and CbO2 do form and that CbO2 is a protective oxide. The growth of CbO2 results in parabolic kinetics until Cb2O5 is nucleated and grows. Apparently because of the large volume change associated with its formation, Cb2O5 is porous and does not serve as a diffusion barrier; linear kinetics prevail after the surface is covered with Cb2o5. On the basis of these observations, several authors5,9,10 have suggested that the linear oxidation of pure columbium at 1000°C in air or oxygen of 1 atm is limited by a Loriers-type mechanism,11 whereby the total rate or reaction is controlled by ionic diffusion through a thin layer of CbO2 which is maintained at a constant thickness throughout the linear oxidation. However, the concept of a Loriers model for a three-phase CbOlCbO2 Cb2O5 scale, with the only oxygen activity gradient across the NbO2 phase, is not self-consistent. Further, the suboxides CbO and CbO2 were not observed in the high-temperature X-ray diffraction study of columbium oxidation by Goldschmidt.8 From investigations in which the large PO2, dependence of the linear scaling rate was demonstrated, the importance of an oxygen adsorption or dissolution step has been suggested.4,5,7,10,12 Thus the mechanism for the linear oxidation of pure columbium remains quite controversial. Since further insight into the oxidation mechanism of pure columbium is not provided by this investigation, the authors wish to emphasize at the outset that their experimental results are not interpreted in terms of a particular rate controlling step for the oxidation of pure columbium. Previous investigations13-18 of the oxidation of Cb-Zr solid-solution alloys in air or oxygen at 1000°C suggest a remarkable dependence upon zirconium content. For an alloy of bulk zirconium mole fraction, N2r(0) equal to 0.05 or 0.10, the oxygen uptake is reported to be as high as four times greater than that for pure columbium;13,14 for alloys with NZr(0) 0.05 or 0.10 the oxygen uptake is reported to decrease with increasing NZr(0); to a minimum uptake of about one quarter that for pure columbium at NZr(0): = 0.50.13-15Since zirconium forms a more stable oxide (ZrO2) than the lowest columbium oxide (CbO), and since columbium exhibits a high solubility19,20 and diffusivity21,23 for oxygen, the internal oxidation of the zirconium component to ZrO2 is expected at a reaction front ahead of the advancing metal/scale interface. The external scale is then formed at the metal/scale interface by the inward migration of oxygen through the scale, probably through a series combination of molecular and ionic diffusion. Internal oxidation in conjunction with external scale formation has been investigated by Maak24 for the oxidation of dilute Cu-Be alloys in pure oxygen at 850°C. For cu-Be and many other binary alloys,24-27 very small, essentially uniaxial internal oxide particles are formed in the most dilute compositions; for somewhat more concentrated alloys. the internal oxide particles precipitate as platelets or needles. From pertinent solutions to the diffusion equation, Maak28

Jan 1, 1967

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By Alan M., Bateman

MR. JORALEMON'S dispassionate discussion of this subject in TECHNICAL PUBLICATION 340 of the Institute shows clearly some of the failures and successes of geology in the discovery of ore deposits. He forces us to recognize, with humility, that chance has played a greater part than geology in the recent discovery of several great copper deposits. I think, however, he wrongly ascribes to unexpected or chance discovery some deposits that were found as a direct result of geological investigation. I refer to the Rhodesian copper deposits,, particularly Roan Antelope and Mufulira, both mentioned by him as having been found by chance. Also,. I think Mr. Joralemon's paper, inadvertently, does not- give the proper credit for the early recognition of the possibilities of these deposits. I feel sure that Mr. Joralemon and the gentlemen given credit by him will welcome any further information on this subject that will throw light on what will some day- be of. historical interest and importance. Consequently, I should like to set forth some additional data that throw light on who should receive the most credit, and' to indicate that, in my opinion, sound. geological reasoning and not chance is to be, credited for the development of the. Roan Antelope and Muf ulira mines.

Jan 1, 1931

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By A. E. Bibb, F. W. Kunz

A platelet form of zirconium hydride was found in zirconium and ZY-1 wt pct U single crystals containing hydvogen in the range of 50 to 100 ppm. The habit planes for the hydride plateletg in the zirconium crystals were found to be {1012}, {1121}, and (1122) while the habit planes in the ZY-1 wt pct U crystals were {1121), {1123}, and (1.231). With the exception of the {1231} plane, these have been identified as the twin planes in zirconium. The different effect of hydridc on the mechanical puoperlies of zirconium at high and low strain rates has been explained in terms of the defornzation mechanism and the habit planes of the hydride. ZIRCONIUM and zirconium-base alloys are considered for many nuclear reactor applications, where the pick-up of hydrogen is a distinct possibility, if not an unavoidable occurrence. An excellent example of this is the absorption of hydrogen by zirconium and its alloys during aqueous corrosion, where as much as 30 pct of the hydrogen produced by the corrosion reaction is picked up by the metal. Under the proper conditions, the absorbed hydrogen would precipitate as zirconium hydride and consequently alter the mechanical and physical properties of the zirconium-base alloys. The knowledge obtained from a study of the crystallographic aspects of the hydride precipitation is necessary for the interpretation of the observed changes in the mechanical and physical properties. The deleterious effect of hydrogen on zirconium-base materials is not always observed in normal slow tensile loadings at or above room temperature, but becomes immediately obvious under impact loading, where the energy absorbed decreases with increasing hydrogen content,' and in notched specimens where triaxial loadings are attained.2 This effect is of serious consequence in the applications of Zr where shock loads or high strain rates are experienced. The purpose of this investigation was to determine the crystallographic planes of the Zr and Zr-1 wt pct U matrices upon which zirconium hydride will precipitate and to correlate these with the observed mechanical property data. PROCEDURE Crystal Growth—Single crystals of Zr and Zr-1 wt pct U alloy were used in this investigation. The Zr crystals were made from sponge that had a typical analysis as shown in Table I. Large grains were grown in this material by rapid cooling an arc-melted charge in a button furnace. This operation undoubtedly lowered the volatile impurity concentration below those listed in Table I. Back-reflection Laue patterns of these large grains showed the presence of considerable substructure and lattice distortion within each grain. It was found that an 18-day anneal in an argon atmosphere at 840°C (a high a heat-treatment) followed by furnace cooling, resulted in the further growth of the large grains and removed the detectable substructure ana lattice distortion. Equiaxed crystals with a cube edge of approximately 1/4 in. were produced in this manner. Large crystals of Zircaloy-2 (1.5 wt pct Sn, 0.15 wt pct Fe, 0.1 wt pct Cr, 0.05 wt pct Ni) also were produced by this technique but the large amount of substructure formed could not be removed by annealing. The Zr-1 wt pct U solid solution crystals were produced from an alloy rod consisting of Westing-house-Foote hafnium-free crystal bar zirconium and depleted uranium. The chemical analysis of the alloy is also given in Table I. Three-inch sections were cut from an 0.120-in.-diameter alloy rod and tapered to a fine point on each end. The samples were sealed in evacuated Vycor tubes, homogenized for 5 hr at 1000°C in the ß-phase field, and slowly lowered in a gradient furnace into the a phase (800°C), annealed for 60 hr at this temperature to produce grain growth and furnace cooled. This technique produced large grains approximately 1/2 to 3/4 in. long over the entire cross section of the rod, which were free of observable substructure. Metallographic examination up to X1000 did not show the existence of any second phase in these grains. Crystal Orientation—All crystals were abraded on fine emery paper to produce two flat surfaces 90 deg to each other. The crystals were analyzed by the standard Back-Reflection Laue technique to obtain the crystal orientation with respect to the abraded surfaces. The Back-Reflection Laue Photograms of all crystals used were clear and sharp indicating that the crystals were free from any substructure that could be detected by these means. Hydriding—Only samples containing four to five grains were used for hydriding. Samples that exhibited fine grained patches were discarded. The samples were hydrided using the following technique. After etching in 48 vol. pct HNO3, 48 vol. pct H2O, and 4 vol. pct HF (48 pct) solution, the specimens

Jan 1, 1961