Search Documents

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By AIME AIME

THE convention which met in Washington at the call of the Joint Conference Committee was called to order at ten o'clock on Thursday morning; June 3, by Richard L. Humphrey, temporary chairman, member of the American Society of Civil Engineers, who made a brief statement of the reason for the meeting. Lieut. Col. Charles W. Kutz, Corps of Engineers, U. S. A., and Engineer Commissioner of the District of Columbia, then welcomed .the engineers composing the convention on behalf of the District of Columbia and, the Washington engineers. Although an elaborate program had been prepared on which were many well-known speakers on interesting and important topics, , it was voted to intersperse this to fill in the usual and unavoidable hiatuses in the business program of such a convention[ Calvert Townley, president of the American Institute of Electrical Engineers, was elected permanent chairman, and J. C. Hoyt, of Washington, was elected secretary of the convention. The following committees were appointed: Consti¬tution and by-laws, Richard L. Humphrey, chairman; resolutions, Philip N. Moore, chairman; and program, F. H. Newell, chairman. Then, Gardner S. Williams, member of the, A. S. C. E. and the Grand Rapids Engineering Society of. Grand Rapids, Mich., and one-time member of the American Association of Engineers, offered the following resolutions:

Jan 1, 1920

By Clarence Linville

IN an article published in the Iron. Trade Review 1 I gave a convenient arrangement for the installation of wet and dry bulb thermometers for use in making moisture determinations in the air being blown into a blast furnace, and also gave a chart for use in obtaining moisture values from the thermometer readings. The data from which this chart was prepared were obtained from the tables in use by the U. S. Weather Bureau.2 The work of Carrier 3 has shown that these tables are somewhat in error. He has recalculated the values for moisture as referred to, wet and dry bulb thermometer readings, and he has prepared a psychrometric chart from the values thus obtained. This work has priced the subject of psychrometry upon a correct scientific basis. I think it is proper that we should recognize the importance of his work and give him credit for one of the most interesting and valuable researches that have been published in recent years. Blast-furnace men are not ready to use, as he suggests 4 a value expressed in grains of water accompanying a pound of dry air. However convenient this may be for heating and ventilating work and other engineering problems, there are several reasons for preferring the use of a value expressed in grains of water in a. cubic foot of mixed air and water vapor, in connection with combustion phenomena and the effects of moisture on blast-furnace operation. Previous papers presented to the Institute have used such values and we have

Jan 10, 1913

By H. K. Birnbaum

The effect of 1ow-temperature stabilization anneals on the structure of the 0 phase Au-Cd alloys and on the diffusionless transformations observed in these alloys was examined by X-yay diffraction techniques. A phase separation in the ß-phase region was proposed to account for the experimenta1 results. The effects of quenching from elevated temperatures on the transformation behavior of these alloys were shown to be consistent with the proposed mechanism. IT has been shown that the high-temperature ß phase (CsCl structure) of the Au-Cd alloy system transforms to a phase having an orthorhombic (D2) ß&apos; structurel1-3 for compositions near 47.5 at. pct Cd and a tetragonal (4/m, m, m) ß" structure* in the vicinity of 50.0 at. pct Cd. Both transformations are diffusionless, crystallographically reversible, and occur on cooling at about 60° and 30°C respectively. The temperature interval from the beginning to the end of the transformation is of the order of 5°C in each case. Although the transformations are normally athermal, some of them have been reported to occur isothermally.= wechsler6,7 has shown that the effects of quenching a 49.0 at. pct Cd alloy from elevated temperatures are consistent with the retention of a nonequilibrium number of lattice vacancies. Annealing of these quench effects results in a broadening of the X-ray reflections.8 After a suitable quench, the 47.5 at. pct Cd alloy transforms to a phase having not the p&apos; orthorhombic structure but another structure which has properties similar to that of the ß" tetragonal structure.5.9 This change in the type of transformation has also been obtained after long anneals in the ß-phase region at about 70oC10 The present investigation was primarily concerned with the structural changes accompanying the above transformation phenomena. The change in transformation product and accompanying physical changes during an anneal in the ß phase have been termed stabilization effects. Experimental Procedure —The results reported in this investigation were obtained with the use of a Norelco diffractometer fitted with a temperature-controlled cryostat. The specimen temperature was controlled to better than ± 0.l°C during the measurements. CrKa radiation monochromated electronically with the use of a scintillation counter and pulse height analyzer was utilized. Specimens containing 47.5 and 50.0 at. pct Cd were prepared by sintering filings obtained from homogenized ingots of the proper alloy composition. (Gold of 99.999 pct purity and cadmium of 99.98 pct purity were used). All heat treatments were carried out with the specimens capsulated in vacuum ( < 10 % mm Hg) or in a He-H gas mixture. The quenching technique used in these experiments was to drop the pyrex capsule which contained the specimen from the annealing furnace into water, the temperature of which was controlled. The pyrex capsule shattered on contacting the water resulting in a relatively rapid quench. After the heat treatment, the specimens were mounted in the diffractometer and were left undisturbed in the diffractometer specimen holder during each sequence of measurements. EXPERIMENTAL RESULTS A) Low-Temperature Annealing—The transformations which were considered "normal" for these alloys were those obtained athermally during furnace cooling at approximately 50°C per hr after an elevated temperature anneal. Under these experimental conditions, the specimens were observed to transform to phases having structures whose diffraction patterns could be indexed as the ß&apos; orthorhombic structure for the 47.5 at. pct Cd and as the 0" tetragonal structure for the 50.0 at. pct Cd alloys. The transformation temperatures on cooling were approximately 60" and 30°C, respectively. Under the "normal" conditions both transformations were observed to go to completion, i.e., the entire volume of the ß phase was transformed to the product phase. In some specimens an extremely weak ß 110 reflection was observed at 20°C indicating that a small amount of retained ß was present. The effect of low-temperature annealing on the nature of the diffusionless transformations was examined for the 47.5 and 50.0 at, pct Cd alloy. The specimens were annealed in evacuated capsules at temperatures in the vicinity of 600°C (as specified in Table I) for 24 hr and were then cooled to 100°C at a rate of 50°C per hr. The specimens were then removed from the capsules and mounted in the diffractometer without allowing the specimen temperature to drop below 80°C. Annealing at the low temperatures was accomplished in the diffractometer by means of the cryostat which was mounted around the specimen. During the low-temperature anneals the lattice parameter, integral breadth of the reflections, and ratios of the integrated intensities of the fundamental and super lattice reflections for the 0 cubic phase were periodically determined. After annealing for the required time, the specimens were slowly cooled in the diffractometer and the diffraction patterns were recorded as a function of temperature. The specimens were cooled until the phase transformations were completed, following which the specimens were heated and diffraction

Jan 1, 1960

By W. N. Poundstone

The mining and ventilating system used in development work in the Pittsburgh Seam in northern West Virginia is discussed. The seam conditions and the nature of the accompanying methane gas are described. The type of equipment and the mining cycle will be discussed, showing how they are well suited for very gaseous development work. Face ventilation in development work is possibly the fastest growing problem of the industry. The coal mines of the future will be faced with the prospect of mining from under increasing depths of cover. Consequently, larger and larger amounts of methane gas probably will be found. The Pittsburgh Seam, in northern West Virginia, is an example of an area already faced with this problem. At the present time, most of the development work being done in this seam lies beneath 500 to 1200 ft of cover. The Pittsburgh Seam in this area has always been very gassy—even near the outcrop—and the recent development work has been accompanied with extremely large volumes of gas. In many cases, a single development section has liberated in excess of 1,000,000 cfm in 24 hr. This problem of heavy gas liberation was the chief concern, several years ago, when continuous mining equipment was first considered at Christopher Coal Co. All of us were apprehensive about the liberation that would accompany rapid extraction in a single working place. However, the experience during the past few years has shown that this ability to mine only one place at a time, is actually the key to working this type of coal. With all of the mining or advancement concentrated in one place, the ventilation can also be concentrated. By this it is meant that continuous mining permits the active working place to be ventilated with a maximum amount of fresh air, taken directly from the intake source without first passing another working place. Continuous mining (and a good ventilating system) also permits a much greater concentration of attention or vigilance to the actual working place. There are two things that are very important to the mining of coal having high rates of liberation. First, adequate volumes of air are necessary. Second, and perhaps more important, a mining and ventilating system must be used that will provide an uninterrupted flow of air to every portion of the working section. Liberations of this magnitude take only a few seconds of interruption for a dangerous accumulation of gas to occur. With adequate volumes of air available, the ability to concentrate ventilation more than offsets the concentration of gas emission that is inherent with continuous mining. The mining system used with continuous mining equipment at Humphrey Mine is similar to the system used at many mines in the area for development work. This system is designed to favor ventilation, realizing that other efficiencies are meaningless if the equipment must stop because of ventilation difficulties. This plan is especially well suited to minimizing ventilation interruptions. Basically, the overall plan of mining is to develop headings into virgin coal and encircle or block out large areas. These blocks are generally at least 2000 ft sq. The purpose of this blocking out is to bleed gas from the area before pillaring. Experience has shown this method to be quite effective, even in the most gassy areas. The gas in this field seems to migrate or flow readily from the solid coal into the outside return headings of the development work. The numerous clay veins and slips that are found in the area are extremely good avenues for gas flow. A block of coal, surrounded with development headings, usually bleeds off readily; and since it is cut off from the virgin coal, it is not subject to gas migration, through the seam, from this source. However, the outside return of the encircling development work, adjacent to the virgin coal, may liberate gas for years. This liberation from the outside ribs in the virgin coal is the reason split ventilation is used in development work. If split ventilation were not used, there would, in many cases, be a serious build-up of gas in the intake before it could reach the working face. Fig. 1 shows a typical development section having seven headings. The two outside places on each side are returns, and the three center headings serve as intakes. This section is equipped with a ripper-type continuous mining machine. An off-track loading machine is used to load from a surge pile on the

Jan 1, 1961

By Carl G. Hogberg

DURING recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. PRINCIPLES OF IRON DESULPHURIZATION IN FURNACE Although investigations of the blast-furnace process have not clearly revealed the detailed mechanism of iron desulphurization within the furnace, they have been sufficiently extensive to permit a postulation of the following general principles: I. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurization is relatively narrow, being confined to a vertical distance extending approximately from tuyere level to the iron-slag interface in the hearth.1 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.2 Coke ash is released as the coke burns in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By AIME AIME

MANY of the important papers to be presented at the World Congress of Engineering at Tokyo, in November, 1929, are being furnished by members of A.I.M.E. and a list of them is given below: "Fifty Years of Physical Metallurgy,,-by H. M. Boylston, Case School of Applied Science, Cleveland, Ohio.

Jan 1, 1929

Why should I pay $8.50 an hour for dealer repairs when my own mechanics work for $3.50?" The numbers vary, but that&apos;s the argument most contractors use to justify doing their own repairs. They don&apos;t realize it, but they&apos;re probably losing big money. For instance, it takes nearly a quarter of a million dollars in tools alone to equip a shop comparable to an average equipment dealer&apos;s facilities. A contractor must buy a lot of expensive, specialized tools he seldom uses, or else settle for the inefficiency of having repairs done by his mechanics with relatively unsophisticated tools. His building soaks up money in rent, maintenance insurance, taxes. His mechanics demand good wages. It even costs money when mechanics aren&apos;t repairing equipment. Mechanics get full wages for slack periods and cleanup time, too. This doesn&apos;t count as service manhours, but it&apos;s still part of the total repair cost. To help contractors uncover these hidden expenses and find out the true cost of owning a shop, some equipment dealers have devised a do-it-yourself "shop cost analysis form."

Jan 1, 1970

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen&apos;s hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr&apos;s salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.&apos; This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,&apos; which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.&apos; The fracture path in ß brass is predominantly transcrystalline,&apos; in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-&apos; after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

By Lucien Eaton

VENTILATION in the iron mines of the Lake Superior region in nearly all cases is natural; that is, it is induced by the difference in elevation between different outlets in the mine and by the difference in temperature of the air in the mine and that outside. This difference in temperature is frequently augmented by placing a steampipe in the upcast shaft; but aside from this, artificial aids to ventilation have been rare until - recent years. In some of the older mines, as at the Cliffs Shaft mine at Ishpeming, Mich., in the 80&apos;s, fans have been used when there was only one opening to surface, but their use was abandoned as soon as a natural circulation of air started. In recent years, the Newport mine at Ironwood, Mich., was the first to use positive mechanical ventilation. The installation was not large enough, however, to give definite results, reliance being placed largely on natural ventilation. With the coming of warm weather in the spring of 1914, the necessity of positive mechanical ventilation at the Lake mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., became evident. The workings of the Lake mine are under the bed of old Lake Angeline, which was pumped out in 1894, and the mine had been in operation for 6 years prior to that date making a total of 26 years of continuous operation. The total production, up to 1914, amounted to over 8,000,000 tons. The ore was first mined by square-set rooms and pillars, but this was later changed to top slicing and caving. Both methods required the use of large amounts of timber, probably 80,000,000 board feet in all, practically all of which remained in the timber mat. The slow oxidation of this timber was one of the principal causes leading to the installation of mechanical ventilation. The mine was served by only one working shaft, called No. 4, a second outlet being provided by a raise to the surface from the old workings on the south side of the mine. This raise was the "down cast;" but it was very small and the drifts and raises leading to it were too small and crooked to permit an adequate amount of air to enter the mine, especially during the warmer weather. Measure-

Jan 8, 1920

By Samuel M. Brock

In recent years society has become increasingly concerned with maintaining and improving the quality of environment. Thus, public interest and concern with pollution problems is now high. This is reflected in recent federal and state efforts to formulate new legislation to prevent pollution and strengthen existing pollution laws. In reviewing literature pertaining to pollution problems, it is possible to distinguish many common elements. The most outstanding of these is the failure of the market to guarantee that private firms responding to price signals generated in the marketplace will make decisions leading to optimal resource use. Cases of market failure in allocating natural resources according to the wants of society frequently are due to the presence of technical externalities, or side-use effects.59 These roughly and generally can be defined as interdependencies among production and consumption units, the impacts of which are exerted other than through the market. They are, in other words, extra-market relationships. The economic unit generating external effects does not take them into account in decision-making. Thus, the tendency is for the unit to produce either more than society desires or not enough. In such cases society often has intervened in the decision-making process. This intervention frequently has taken the form of legislation to regulate production and consumption activities. Thus, a body of institutions, which acts as a constraint in decision-making processes, has materialized. These institutions are often far more influential in their effect upon resource use than are the forces of supply and demand acting in the marketplace. The problem of environmental pollution is essentially the problem of handling residuals which are the byproduct of all production and consumption activities which take place in the economy.2 These residuals are emitted into the air and water and disposed of on the land. They are interrelated, in that efforts to control emissions into the air or water can result in the production of solid wastes, which then present disposal problems. It is convenient to separate residuals by the type of pollution they cause-air, water, and land while remembering that these problems are related and that solutions may require coordinated effort.1 Residuals may be produced in both production processes and consumption. Residuals produced in production by the mineral industry, or firms utilizing its products, range from emission of sulfur dioxide by steam generating plants to radioactive mill tailings produced in the course of mining uranium.. Residuals associated with consumption are generated mainly through transportation of members of the household, space heating, and in the disposal of solid wastes, including refuse and junk autos. Residuals associated with both production and consumption receive attention in ensuing sections of this chapter.

Jan 1, 1976

By H. R. Peiffer, R. Geckle

The silver phase of silver and finely divided alumina composites is shown to grow as single crystabs upon solidification from the melt. These crystals grow without the aid of an externally applied thermal gradient or a mold. The single-crystal growth is more readily disrupted as the alumina content varies from the optimum concentration of 20 wt pct. Pretreatment such as variation of fabrication pressure, and presintering of the specimens appear to play a lesser role in this phenomenon. In actual practice the growth of single crystals of metals from the melt is a tedious, painstaking process.&apos; Care must be taken to insure the proper thermal gradients and rate of growth in a vibration-free environment. Excellent single crystals can be grown when these variables are controlled. When a second insoluble and finely divided phase is present in the melt the growth of single crystals is difficult, if not impossible, even under the most favorable conditions outlined above. During the past few years, a composite of silver and alumina has demonstrated an ability to resist flow even though the major phase, silver, is mo1ten. 2 A more surprising feature of this material is the ease with which single crystals of silver grow upon cooling the composite from temperatures above the melting point of silver to temperatures near room temperature. Observations have been made that demonstrate that single crystals of silver will grow even when conditions most unfavorable for growth of pure silver crystals exist. The crystals grown in this manner are imperfect in that a great deal of subgrain structure exists. It is the purpose of this manuscript to qualitatively describe this process and to attempt to isolate the influencing factors of this behavior. MATERIAL PREPARATION The composite material is prepared by powder-metallurgical techniques. Two items of great importance are the introduction of oxygen into the system and the obvious need for a thorough mixing of the metallic and refractory oxide phases. The oxygen is necessary in order that the silver wets the alumina. Without oxygen the phases separate and the material shows no unusual properties. In order to supply the needed oxygen the silver is added in the form of silver oxide which is readily decomposed to oxygen and silver upon heating. The silver oxide is readily obtained in a finely divided form that allows a uniform mixture of the alumina and silver oxide to be prepared. The correct ratio of alumina to silver oxide is mixed in the presence of alcohol in an ordinary food blender. The mixture has the consistency of a thin slurry and after mixing for approximately 20 min is dried and pressed into billets at various pressures. As is shown in Fig. 1, there is no limit to the shape of the specimens obtainable as single crystals. These billets are heated in air in a predeter-

Jan 1, 1964

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.&apos; Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-&apos; have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.&apos; Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.&apos; The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6&apos; and 16" crystals and with 1300 ppm oxygen in the 33&apos; crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.&apos;p7

Jan 1, 1969

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow&apos; was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area&apos; of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell&apos;s Eq. 7) becomes dell&apos;s expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell&apos;s data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By BERNARD PLANNER

PRODUCTION COSTS, profits, and quality are the primary factors in the peacetime production of iron and steel. In a war emergency, as high production rates and as complete utilization of readily available raw materials as possible, consistent with securing passable quality, become the most important factors. In this connection a discussion of some of the recent developments in the German iron and steel industry, where the problem of scarcity has naturally always been more acute than in the U.S.A., maybe of interest. To get more pig iron out of the existing blast furnaces it was necessary to obtain the maximum efficiency from the iron-bearing raw materials. This was achieved by eliminating all "excess baggage," chiefly by beneficiating the ore. The preparatory work for this was done by various methods which are effective when the ore either is too poor or contains too many impurities or too much gangue. Some of the beneficiation methods are well known, some are combinations of wet-mechanical, magnetic, roasting, sintering, and other treatments.

Jan 1, 1942

By T. S. Fuller

VARIOUS phases of the embrittlement of solid copper containing oxygen by the action of reducing gases at high temperatures through the work of many experimenters are familiar to readers of metallurgical literature. In 1900, Heyn1 recorded observations of copper being heated in hydrogen with the development of fine cracks, the result of the formation of steam within the metal through the action of hydrogen on the copper oxide usually found in copper. Archbutt,2 in 1905, published the results of experiments, showing that all oxygen can be removed from copper by heating to redness, for several hours, in hydrogen. Intercrystalline cracks and extreme brittleness developed. Archbutt attributed the brittleness to the reduction of oxides present in the copper. Bengough and Hill,3 in 1910, encountered the now well-known embrittlement at the outset of their investigation and stated in their paper: It soon became evident that the effect of any heat treatment depended largely on the presence or absence of reducing gases in the atmosphere of the furnace, as well as on its temperature. Hence it became necessary to adopt a somewhat elaborate scheme of heat treatment. The authors found embrittlement in separate experiments due to both hydrogen and carbon monoxide and concluded that: "The gases ruin the alloys after being heated to about 650° C. in their presence."

Jan 2, 1926