Search Documents

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3'4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By Charles Brush

THE general subject of accurate pyrometry, its great development in recent years, and the importance of its application in arts and manufactures is so ably treated in other papers that this paper will bee confined to a resume of some research work on certain temperature effects in carbon and other steels, some of which appear to, be new. The results of these researches are embodied in several papers presented to' various scientific societies during the last few years, most of them under the general title of Spontaneous Generation of Heat in Recently Hardened Steel.1 Several years ago, when studying the behavior, tinder certain conditions, of specimens of hardened tool steel, I observed that they all spontaneously generated a small quantity of heat, the rate of generation diminishing from day to day for several weeks before generation became imperceptible in the sensitive calorimeter used. In each case the steel had been hardened only a few days prior to its use. It seemed highly probable that the generation of heat was associated with some sort of "seasoning" or incipient annealing process, perhaps accompanied by slight changes of volume, and that it would be most rapid immediately after hardening. I subsequently investigated this curious phenomenon more fully. Twelve ½ in. round bars of tool steel, 5 in. long and with machined surfaces, were hardened by heating to high cherry red in a reducing atmosphere of a gas furnace and quenched in cold water. The bars then had a thin strongly adhering coating of black oxide. They were next stirred in a large quantity of water at room temperature, to acquire that temperature, wiped dry, and oiled with heavy, neutral mineral oil to prevent generation of heat by further surface oxidation, wiped free of excess of oil and placed in the copper cylinder of a heat-insulated box.

Jan 9, 1919

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

By V. S. Gupt, W. H. Somerton

Rock may undergo great changes in physical properties when heated to high temperatures and then cooled, The temperature and intensity of reactions causing rock alterntiorl.s can he controlled by introducing certain chemicals during heat treament. Three typical outcrop sandsone samples were saturuted with common salt solutions, then heated to several maximum temperatures. After cooling, it was found that per-rrreuhilities had increased much more for salt-saturated samples than for samples not saturated with salt but heated to the same temperatures. This was only true, however. for samples heated above the melting points of the particrrlar salts. Potassium chloritle was particularly effective with Bandera sandstone. Samples saturated with potassium chlorirlr. solution and heated to 900C showed an 11-fold increa.se in perrrieahility. Samples without potasrirdrn chloritle but heated to the .same temperature. showed only a 2.7-jold incresre in permecahility. In application, it seems possible that injecting chemicalc into the formations from a wellbore followed by applying intensive borehole heating might promote reactions which would greatly improve permeability of the formalions. INTRODUCTION Great changes in the physical properties of rocks which have been heated to temperatures in the range of 600 to 800C have been reported earlier. Permeability increases of 50 per cent, and equivalent decreases in sonic velocity and breaking strength have been observed. Although there might be some suppression of certain reactions responsiblc for these changes when rock samples are heated under simulated reservoir pressure conditions. recent work has shown that these are more than offset by the increased importance of other reactions at high pressures. The reactions considered responsible for alteration of rock properties by heating include differential thermal expansion. dehydration, phase changes and dissociation of mineral constituents. Ceramists have long known that temperatures at which reactions occur can be raised or lowered by the presence of certain impurities in the sys. tcnl. Thus the possibility exists that by saturating rocks with appropriate solutions. desired reactions might be accelerated and unwanted reactions might be suppressec! when the rock is heated. Purpose of the present work was to investigate the effects of several common salts on the thermal alteration of sandstones. Types of reactions which might occur are reviewed and the findings of a number of thernlochemical alteration tests are presented. THEKMOCHEMICAL ALTERATION OF SANDSTONE MINERALS The most abundant constituent of most sandstones is quartz. Quartz can exist in at least eight different forms, but in the temperature range of immediate interest (to 900C) only two forms are of importance—alpha quartz below 573C and beta quartz above this temperature. Although the alpha-beta inversion of quartz is very important in thermal alteration of rocks. it is not particularly important here because the inversion temperature cannot be changed significantly by the presence of impurities or by the application of pressure. The transition temperature of quartz to tridynlite is 867C. but the transition is very sluggish. Tridymite is considered to be a metastable transition phase between two stable phases: quartz?cristobalite. However. the transition temperature for tridymite to cristobalite is 1,470C.4 The quartz-tridymite-cristobalite transition can be accelerated substantially by the presence of fluxing agents. Finely divided calcium, magnesium and titanium oxides accelerate the conversion while A12O may retard it. A Mixture of NaCl and CsCl reduces the temperature for cristobalite formation by as much as 420°C. Feldspars constitute the second most important mineral in sandstones. The melting points of feldspars range between 1,000 and 1,700°C depending upon the variety. No information available indicated any important role of fluxing agents in the thermal alteration of this group of minerals. Carbonate minerals are subject to dissociation at temperatures within the range of the present investigation. The dissociation of magnesite can start at a temperature of 373°C, but the reaction is sluggish and might not occur untll a temperature of 500°C or ,higher is reached. Dolomite dissociates in two stages at 500°C and 890°C, whereas calcite dissociation temperature is about 885C. Because CO2 is released in the dissociation of carbonates, ail such reactions are somewhat dependent upon CO2 partial pressure. In the absence of CO: in the surrounding atmosphere, the dissociation of calcite starts at 500°C.However. when 1 atm of CO surrounds the sample, the dissociation does not start until 900C. The other carbonates are apparently much less sensitive to a change in partial pressure of CO2. The aragonite calcite transformation can occur an!. where within the temperature range of 357 to 488°C. depending upon the presence of impurities such as barium. strontium. lead and perhaps zinc. The differential thermal analysis (DTA) curves of both magnesitc and dolomite vary with the presence of 'impuritics. The presence of iron in particular seems to affect the magnesitc DTA curve

Jan 1, 1966

By AIME AIME

A STUDY of subsidence and ground movement in the copper and iron mines of the upper peninsula of Michigan has been made by W. R. Crane of the United States Bureau of Mines and published as Bulletin 295 of 66 pages and 49 illustrations. As a result of subsidence, the country adjacent to the mines and over- lying the mine workings in this district is often broken to such an extent as to affect its value; mine shafts and development openings are occasionally so damaged as to be rendered useless, and water can enter the workings through fractures and cave-ins. The problem is more serious in the iron-mining districts, where villages and towns not owned by the operating companies have grown up around mining operations.

Jan 1, 1929

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

By J. B. Dilworth

The purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resourcee, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigatioil pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnois-sance was attempted: such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their

Jan 1, 1913

By A. L. Engel

IN the treatment of complex ores by flotation, one of the most important steps is conditioning the feed. Conditioning primarily consists of the addition, in the grinding circuit, of an alkaline reagent, for example sodium carbonate, which neutralizes any acidity of ore and mill water, counteracts the effect of 'harmful soluble salts, disperses colloids, and provides the necessary alkalinity for the best metallurgical results. The several minerals of the ore should be put in such condition that they may be floated or rejected as desired, through the action of further reagents thereafter used.

Jan 1, 1932

The following is am incomplete list of members and guests who called at Institute headquarters during the period May 10, 1918 to June 10, 1918. Arthur K. Adams, Potrerillos, Chile. J. M. Mahoney, Wilkinsburg, Pa. John Carter Anderson, Tucson, Ariz. Benjamin L. Miller, South Bethlehem, Pa. George S. Blair, Camp Cordon, Ga. Wilbur A. Nelson, Nashville, Tenn. W. A. Deane, Summitville, N. Y. Miles G. Nixon, Chicago, Ill. Charles H. Fulton, Cleveland, Ohio. Walter G. Perkins, San Francisco, Cal. Rudolf Gahl, Inspiration, Ariz. G. M. Ponton, Ottawa, Canada. C. C. Griggs, Eureka, Utah. D. A. Powell, Columbus, Ohio. J. F. Hanst, Potrerillos, Chile. H. W. Reed, Salt Lake City, Utah. Stanley C. Herold, Pittsburgh, Pa. J. C. L. J. Seelig, Padong, East. Indies. Floyd D. James, Boston, Mass. Oberlin Smith, Bridgeton, N. J. Charles Janin, San Francisco, Cal. Harrison Souder, Cornwall, Pa. E. Horton Jones, Copper Cliff, Ont. Stanley A. Spellmeyer, Camp Meade, Md. William Kelly, Vulcan, Mich. Roger S. Sperry, Waterbury, Conn. Ichiro Kitsunezaki, Tokyo, Japan. D. R. Thomas, Toronto, Canada. P. K. Lucke, San Antonio, Tex. Thor Warner, Phoenix, Ariz. E. Francis McCrossin, Birmingham, Ala. L. Douglass Anderson, formerly superintendent of the United States Smelting Co., Midvale, Utah, is now manager of smelters, Intermountain District, United States Smelting, Refining & Mining Co., Salt Lake City, Utah.

Jan 7, 1918

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years' history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.' The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field's history subsequent to Jan., 1952 (see Fig. 1)'.

By Saluja, Sunder S.

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including fire setting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century.

Jan 1, 1968

By Thomas D. West

The occasional reports of progressive furnace-men, giving the results of physical tests to prove the superior qualities of their pig-irons, have encouraged the writer to believe that the time is ripe for the discussion of such work, and the inauguration of some correct system by which the furnace-man and the founder could make intelligent comparison of the elements of strength, deflection, contraction, and chill presented in pigmetal. In most cases the physical tests now made by furnace-men define but one quality in the iron, and are generally too vague to permit any true comparison. For example, one furnaceman tells us he can punch holes in his cast-iron, wishing it to be inferred that the iron is very soft and strong. Another furnace casts a long wedge, the thin end running to a knife's edge, which is supposed to prove the fluidity of the iron, for the founder's benefit. Another casts in square-cornered " chills," to define the hardness or softness of the metal. To the writer's knowledge these tests are not advocated by their originators as suitable for standards; and they are, to his mind, but evidence of unrest on the part of progressive furnace-men, who feel that something should be done in the line of physical tests. The writer knows of no furnace-men who make and keep records of the strength of their iron obtained by means of tests made on recognized standard testing-scales ; but he does know of a prominent furnace-salesman, who, not long ago, came into possession of a 1-inch square bar that stood 1400 pounds

Jan 1, 1897

By G. W. Sheary

At Bethlehem's Grace mine's 6000-tpd pelletizing plant a cascade control system is utilized to approach a constant magnetite filter cake moisture, a critical factor in obtaining quality green pellets. Variables being controlled by instrumentation are filter feed solids, filter tub level, first and second stage pump sump levels and thickener sludge level, all at varying feed rates. Startup difficulties, modifications and contemplated additions to obtain closer control of the moisture are discussed. Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Co. 's Beth-lehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with %-in. slotted vibrating screens. The ore is washed and screened in the mill and the 1/4-in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30-in. cyclones, to 1% on 100 mesh and 65% -325 mesh. The ground ore is magnetically concentrated by three-drum permanent-type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50-ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% +'1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica. It has been the usual practice to maintain constant filter tank level by pumping an excess constant volume and using a moveable fishtail splitter to divert the desired amount of slurry to the filter tank. The excess from the fishtail and from the filter overflow pipe, which maintains a constant level, is returned to the source. At the Grace mill, tremolite builds up in the pipelines when pumping heavy magnetite concentrate slurries, making it necessary to use polyvinyl

Jan 1, 1962

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By E. Brunner, G. L. Hassler, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By G. L. Hassler, E. Brunner, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By Nicholas J. Grant, Joseph T. Blucher

High-purity aluminum and an Al-10 pet Zn alloy zvere tested in axial fatigue from 80" to 900oF, at struzn vales of 5 and 150 pct per min, at a strain amplitude of 1 pcl. Cycles to failure were recorded as well as the load per cycle during the entive test. Several grain sizes were examined in each material. Examination was made of modes of deformation, initiation and growlh of' cracks, and vecovery mechanisms such as srbgrain formation and boundary migration. Strain rate effects on cycles to failure are first observed ahoi'e 50O0F, the highev vate vesulting in longer lije. Crack initiclion at room temperature may be truns-or iutercrystalline but fructures are transcrystalline. Abore 600'F, crack iniliation and growth ave largely inlercvystalline. Boundary wzigratiotz to 45-deg positions is observed above 70Oo F, and fractrrves are a combination of grain bol~ndary voids and cvacks. It is only in recent years that studies of deformation and fracture which prevail in fatigue at elevated temperatures have attracted significant attention.' Of such studies considerably less attention was given to high strain-low strain rate fatigue. Moreover, the majority of high-temperature fatigue studies were performed at conventional machine speeds (1000 to 10,000 cpm). As it is well-demonstrated in uniaxial creep-rupture series, at high strain rates, even at high temperatures, metals undergo work hardening with little or no attendant recovery or recrystallization thus the nature of deformation and fracture which is observed is similar to that encountered at lower temperatures.'-" Thus, for example, fatigue testing of a stainless steel at 750°F does not involve high-temperature deformation processes,2 and might more correctly be termed "fatigue testing at an elevated temperature". It was the purpose of this work to study deformation and fracture in fatigue as a function of low strain rates and temperature, selecting conditions which would result in grain boundary sliding, migration, fold and subgrain formation, and intercrystalline cracking in high-purity aluminum and a high-purity A1- 10 pct Zn alloy. Grain size was an additional variable. Extensive studies of the deformation and fracture behavior of these aluminum materials in simple creep had been done in the authors' laboratory, and were to serve as a basis of comparison for the observed effects in fatigue:'-'' the range of the creep test temperatures was 80° to 1150oF. MATERIALS AND EXPERIMENTAL PROCEDURE The compositions of the 99.99 pct pure A1 and the A1-10 pct Zn alloy are shown in Table I. Button-head specimens, with a liberal fillet, of 0.20 in. diam and of gage length 0.40 in. were machined from wrought bar stock. The ratio of 2:l gage length to diameter was selected after preliminary tests showed that a shorter length gave a shorter life, probably due to end effects, and after evidence of buckling in longer gage length specimens. After machining, the specimens were chemically polished to remove the worked outer layer, and were subsequently heat-treated to stabilize the selected grain sizes. Both the high-purity aluminum and the A1-10 pct Zn alloy were heat-treated to produce grain diameters of approximately 0.5 and 2 mm in each case. These grain sizes are referred to in the text as fine and coarse grain, respectively. One lot of the high-purity aluminum was heat-treated to produce a still coarser grain size in which the cross section was occupied by 2 to 3 grains. This structure is referred to as very coarsegrained. After heat treatment, the specimens were again electropolished. To avoid complications of both stress and strain gradients in the cross section of the specimen, a hydraulic, axial fatigue machine was designed and built. A button-head specimen, 1/2 in. diam at the head, was firmly gripped in a split-type holder free of any play in the grips. The test temperatures varied from 80" to 900°F. The strain amplitude in all of the reported tests was 1 pct for a total strain amplitude of 2 pct. The strain range was set by precision micrometers and measured by a precision dial gage. Constant strain rates of 5 and 150 pct per min were selected so that high-temperature type deformation and fracture would occur in the higher-temperature tests5,6 The strains and strain rates must be regarded as nominal values because they are based on the original specimen dimensions, which changed significantly as a result of necking and crack propagation, as can be observed from Fig. 8. For the elevated-temperature tests, a thermocouple was inserted into a well in the head of the specimen; the selected temperatures could be maintained with less than ± 5oF fluctuation during the entire test. To avoid changes in grain size before the test, specimens were heated to the test temperature in less than 15 min; similarly, they were cooled to room temperature after fracture with an air blast to avoid or minimize recovery or recrystallization. During the fatigue tests, load vs strain curves were recorded by a strain gage load cell for each fatigue cycle. In addition, the maximum values of load amplitude were recorded for the entire test.

Jan 1, 1968