Search Documents

By Eugene W. Pearson

In a marked departure from conventional practice, the Power Plate process combines the two unit operations of leaching and electrowinning into a single continuous step for direct recovery of copper from sulfide concentrates, cement copper, copper scrap, and copper oxide slurries. Considering how environmental controls are pre- venting development of smelters for additional capacity or new construction, the Power Plate process provides a welcome pollution-free alternative to the smelting-electrorefining routes. And its low capital investment and low operating costs also recommend it to copper producers who are now using or investigating various hydrometallurgical methods.

Jan 12, 1974

By C. W. Volek, G. Mandl

Steam-injection tests in the field have shoum that heat transport into the oil/water region, ahead of the steam zone, may have a significant effect on the production process. Earlier theoretical work on reservoir heating by hot-fluid injection can be used to describe the growth of the steam zone, but only if heat transport from steam zone into oil/water region is neglected. It therefore became necessary to re-examine and extend the earlier theory. It was found that this theory ceases to be consistent with the physical model of the process at a certain critical time, tc, which depends on reservoir thickness, temperature, and quality of the steam. The critical time marks an important change in the heat flow across the condensation frovt: the heat flow, which is purely conductive during 0 < t < tc&apos; becomes predominantly convective at t = tc. Accordingly, at t = tc, the equation which governs expansion of the steam zone changes. On the basis of the new equation, an approximate description for the steam-zone growth during t > tc is developed by making use of upper and lower bounds for the exact solution of the problem. The boundary conditions for heat and mass flow inside the oil/water region are established, and a simple method of detennining the saturation at the downstream side of the condensation front is presented. Experimental results show that the theory gives an accurate description of steam-zone expansion before the critical time. At times near critical time, and also after critical time, experimental data show theoretical steam-zone volumes to be high. Even so, the accuracy of the calculated steam-zone volumes is sufficient for practical purposes. THEORY OF STEAM-ZONE GROWTH INTRODUCTION The engineering evaluation of steam-drive processes is based mainly on a mathematical description of reservoir heating by hot fluid injection presented several years ago by Marx and Langenheim.l This theory can be used to determine the growth of the steam zone,2 provided the flow of heat from the steam zone into the liquid zone ahead of the condensation front (Fig. 1) is neglected. Since we must expect, however, that heat transport into and inside the liquid region (the region between condensation front and production wells) will affect both the water/oil flow and the growth of the steam zone, it is necessary to re-examine and to generalize the Marx and Langenheim theory as applied to steam drive, which will hereafter be termed the "old" theory. Observations made in several field tests emphasize the need to study the heat flow across the condensation front (CF). On several occasions it was discovered that heat was transported in the liquid zone far ahead of the advancing CF, resulting in an early breakthrough of warm water. This seems to occur most often when high injection pressures are applied, when "wet" kONINKLIJKE/SHELL EXPLORATIE EN PRODUKTIE LABORATORIUM RIJSWIJK, THE NETHERLANDS SHELL DEVELOPMENT CO. HOUSTON, TEX.

Jan 1, 1970

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines "Refractories" as "Material, usually nonmetallic, used to withstand high temperature," and it defines the term "Refractoriness" thus, "In refractories the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use." The ability to withstand high temperatures is critical to classifying a material as a "refractory." However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incident to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, Sic, ZrO,, zircon, borides, and nitrides). Brick are, of course, preformed and are usually heat treated at high temperatures before use, but are in some instances unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Brick are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 9 x 4 ½ x 2 ½ in. and 9 x 4 ½ x 3 in. straights and series. All other brick of non- standard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application.

Jan 1, 1975

By G. H. Pardue, L. H. Gollwitzer, J. H. Moran, R. L. Morris

Experimental and theoretical studies of casing-borne signals have provided data on the attenuation efect, compressive strength and shear modulus for different types of cement. These data resulted in the establishment of a definite relationship between the cement compressive strength and the Cement Bond log reading. The relationship is influenced by the casing dimensions, but is independent of the type of cement and the curing conditions. The theoretical analysis provides a mathematical statement of the phenomenon and shows that the attenuation rate is basically a function of the shear modulus of the cement and the thickness of the casing. The lab tests provided a connection between the shear modulus and the compressive strength, and permitted a comparison of the experimental and theoretical work. The results of the experimental and theoretical study have provided means of quantitative interpretation of the Cement Bond log. This interpretation is made more convenient with the use of a nomograph. INTRODUCTION Past interpretation of Cement Bond logs has been essenlially based upon a qualitative comparison between the log response in the zone of interest and the responses in the "fully cemented" and the "uncemented" intervals. Most of the variables influencing the magnitude of the signals were recognized in an earlier paper&apos;; however, insufficient laboratory data were available at that time for quantitative evaluation of these variables. Early attempts to use the numerical amplitudes of the signals without full knowledge of their significance resulted in erroneous comparisons between various types of cement. An extensive program was undertaken to evaluate, both experimentally and theoretically, the attenuation phenomenon and to study the effects of the more common variables. A major objective of the experimental program was to obtain data on the relationship between cement-bond-tool response and physical property standards used by the industry so that practical interpretation methods could be devised. The studies included a comparison of attenuation rate with these properties as a function of time, temperature and pressure, using common sizes of casing. The main result was that a definite relationship was established between the compressive strength of the cement in inti- mate contact with the casing and the response of the cement bond tool. For a given casing thickness, regardless of the type of cement or the curing conditions used, the attenuation rate is a function of the compressive strength. A theoretical analysis showed that the attenuation rate for casing-borne signals should be a function of (among other things) the shear modulus of the cement and the thickness of the casing. The relationship between the compressive strength and shear modulus for curing times similar to those encountered in the field was determined from laboratory tests. Using this relationship, the computed attenuation rates showed reasonable agreement with the measured attenuation rates. The purpose of this paper is to report the results of the experimental and theoretical investigations and to present the first practical method for a quantitative interpretation of Cement Bond logs based on known variables. This method is applicable where the casing-borne signal is not affected by high-velocity formation arrivals. DESCRIPTION OF LOGGING TOOL The Cement Bond logging tool shown schematically in Fig. 1 has been described previously.&apos; The tool consists of two sections: acoustic and electronic. The acoustic section contains a transmitter and a receiver, usually spaced 3-ft apart. Sonic energy emittted by the transmitter travels through the casing and is detected at the receiver. The electronic section measures the amplitude of the

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.&apos;-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during &apos;"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term &apos;&apos;productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during &apos;"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term &apos;&apos;productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association&apos;s Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By Guy R. B. Elliott

If chemical mining is to work, it is extremely important to watch heat balances. Some reactions with coal give off heat and others absorb heat. The reactions of coal with oxygen or air give off heat, but the reactions of coal with steam or with carbon dioxide absorb heat. By balancing the proportions of the two types of reactions, the energy of the coal can be almost completely recovered and environmental damage is minimized. The chemical reactions are listed in Table 1 in the usual form with subscripts (s) and (g) indicating solid or gaseous materials. In reaction 1, solid corbon, C(s), reacts with gaseous oxygen, O2(g), to produce gaseous carbon dioxide, CO2 (g). H means enthalpy or available heat in the material; F is free energy, and it measures whether the reaction can go at all, and if so, how much.

Jan 9, 1973

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1&apos;2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam&apos;s length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft&apos;; L is the span, ft; E is Young&apos;s Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By Frank C. Greene

Drilling for oil and gas in Missouri continued at a slightly lower rate than has been prevailing. A summary of operations for the past few years as compiled and published by the Missouri Geological Survey and Water Resources is as follows: Two oil pools are being developed in Cass County. Neither area has been drilled completely, and detailed descriptions will not be given at this time. In the Endicott pool in the southern part of T. 44 N., R. 33 W., oil is found in the Warrensburg sand, which is now considered to be the Big Lake sand of eastern Kansas. The top of the sand is about 125 ft. below the Herthalimestone. The best well is reported to have made 14 bbl. per day for the first four days. The oil is 30" to 32&apos; BB. gravity. This is the only pool in the state, aside from the older areas on the east and west edges of Lees Summit, Jackson County, that is producing oil from the Warrensburg sand. Drilling continues in the Knoche pool in the central part of T. 46 N., R. 33 W., where the oil is found in the Squirrel sand. The oil produced by both these pools is sold by truck in Kansas City.

Jan 1, 1937

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

The subjects of this study are two corrosion phenomena familiar to operators of aluminum plants employing Soderberg anodes of the vertical type, namely the sul-fide scale formation observed at the steel contact spikes and the corrosion wear observed at the lower edge of the gas collecting skirts. The causes of these corrosion phenomena are discussed on the basis of observations from practice and measurements on commercial cells as well as on laboratory experiments. It is concluded that the anode spike corrosion is mainly due to the attack by sulfur compounds contained in the anodically evolved gases and that this attack is greatly promoted by cracks and pores in the anode carbon embedding the lower spike ends. The corrosion of the gas collecting skirt is mainly attributed to anodic dissolution of the iron during occasional contacts with the melt. ANODE SPIKE CORROSION The visible result of this corrosion is the formation of a brittle loosely adherent scale on the lower ends of the mild steel spikes maintaining the electric contact to the carbon anode, Fig. 1. The thickness of the scale usually varies from 0.5 to 3 mm, but in some cases scale of about 10 mm thickness has been observed by the writers. During the spike pulling, usually repeated every 3 weeks, part of the scale often loosens and remains in the anode carbon, resulting in contamination of the aluminum with iron. This corrosion has been attributed to reaction of the iron with gaseous sulfur compounds originating from the anode paste materials.&apos;-4 This paste usually consists of 70 pct precalcined petroleum coke with 1.2 to 1.4 pct S and 30 pct coal tar pitch containing 0.5 to 0.7 pct S. During operation the gasification of the anode materials takes place in two ways: First, gases are evolved by the gradual baking of the anode paste added on top of the anode. Due to the sealing effected by the upper semifluid zone of the paste, these gases, containing sulfur compounds from the pitch, are forced downward through pores and cracks in the rigid anode carbon. At the temperatures of the zone of the lower ends of the spikes, 700" to 900°C, the original components of the baking gas must undergo decomposition, similar to that taking place with the production of coal gas, resulting in a gas mixture consisting mainly of H2 and CH4 with small percentages of H2S as the main sulfur compound.5 Second, the anodic reaction results in a mixture of C02 and CO, the total quantity of which is about 15 times that of the baking gas. These anode gases must carry the entire sulfur content of the carbon gasified by the anodic reaction. Henry and Holliday6 have shown that COS is the main sulfurous component of the anode gases from Soderberg cells. Soderberg anodes usually exhibit a network of vertical cracks, frequently traversing from one spike to the next one and to the outside of the block and widening downward to the working face of the anode. In addition the anode carbon, particularly that below the spike ends, is rather porous, as indicated in Fig. 1. It therefore seems probable that the anode gases also may partly penetrate to the spike ends. As the anode is partly immersed in the melt, the static pressure of this must forward this penetration. I) SPIKE SCALE COMPOSITION A great number of freshly extracted spikes from industrial plants were inspected and samples of the scale collected for examination. Before analyzing the samples a thin iron oxide layer, formed by air oxidation of the outside of the red hot scale immediately after spike pulling, was removed. On the average the Fe/S ratio found by these analyses corresponded to I the composition FeSl. oo7. X-ray powder patterns showed no oxide and otherwise agreed with those found by Haraldsen7 for iron sulfide with 50.00 at. Pct

Jan 1, 1970

By F. H. Willcox

In Bessemer-steel practice, air is blown through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and cafbon. Toward the end of the blow, when the iron is not protected from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Besserner and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast iron. is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blow holes lies in part in the presence of dissolved oxide of iron in the molten steel and its consequent reaction with the carbon of recarburizers, when these are added, to form gases. (Another factor in the origin of blow holes is, of course, the solubility of gases themselves in the steel and

Jan 1, 1917

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By AIME AIME

WHEN I was getting data for my books on ore dressing, I traveled across the continent, visiting a great many mills, always accompanied by my vanning shovel, and I got to be a joke among the millmen. They would say "Here comes the Professor with his vanning shovel." With the aid of this vanning shovel, I examined the tailings of all the mills I visited and I found it to be universally true that they contained some extremely fine, free mineral. I looked everywhere to see if I could find a machine or a process that would save this fine mineral. But nowhere did I find anything that made any bid for success until I visited the Kennedy mill, with its Gates canvas plant, on the Mother Lode of California. There I found that the tailings of the Frue vanners were put into a one-spigot classifier of good design which yielded a spigot product entirely free from this fine, free mineral which only assayed 40c. to the ton in gold. The overflow was extremely fine and as¬sayed $3 to the ton. This overflow was fed to ten canvas tables each 10 ft. square, with the grain of the canvas running across the table to make for the roughest surface. The canvas used was No. 6 cotton duck sail cloth.

Jan 1, 1934

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.&apos; The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945