Search Documents

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By AIME AIME

A CORPORATION would go into bankruptcy if its affairs were conducted as are those of the state of New York, according to the Committee on New York State Government Reorganization of the American Engineering Council of the Federated American Engineering Societies, in a report to the chairman, of the Joint Judiciary Committees of the Senate and Assembly. The report, just made public, was signed by the three members of the committee who were appointed by Herbert Hoover. They were H. de-B. Parsons, chair- man, Paul G. Brown and Lewis B. Stillwell. Although the American Engineering Council is a national organization, it decided to aid in governmental reorganization in New York State because of the magnitude of the task. The Council's committee in its report urged the passage of three state reorganization amendments for consolidation of departments, an executive budget system, and a four-year term for the higher state officials. In the words of the report :

Jan 1, 1921

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

By E. H. Wells, A. Andreas

New Mexico retained its position as the sixth largest oil-producing state for the year 1937 with a total production of 38,484,630 bbl. This was an increase of 11,680,184 bbl. over the 1936 production of 26,804,446 bbl., or a gain of 43 per cent. The production for Lea County during 1937 was 35,961,056 bbl.; for Eddy County, 2,136,251 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 387,323 bbl. The average daily non-marginal well allowable for Lea County on Jan. 1, 1937, was 92 bbl.; at the close of the year it was 67 bbl. The average daily pipe-line runs were less than the allocations of the New Mexico Oil Conservation Commission, but slightly in excess of the state allowables recommended by the United States Bureau of Mines. The average daily production for the year was 105,437 barrels. The total number of completions in the state was 742, of which 638 were oil wells; 19 hydrocarbon gas wells; 5 carbon dioxide gas wells and 80 dry holes. Of the dry holes, 46 were in proven fields. Of these 46 dry holes, 13 were in the Artesia-Grayburg-Jackson-Maljamar area, Eddy County, two in the Getty Extension field, Eddy County, 11 in the Red Mountain field, McKinley County, three in the Rattlesnake field, San Juan County, and nine in the Aztec-Bloomfield area, San Juan County. There were only eight dry holes in the proven fields in Lea County. Southeastern New Mexico Lea County.—The Monument field was the largest producing field in Lea County, with 10,945,788 bbl., closely followed by the Eunice field with 10,927,929 bbl. The Hobbs field, formerly the largest producing field in Lea County, was relegated to third .place, with 7,292,522 barrels. Drjlling during the year closed the gap between the northern part of the Eunice field and the southern part of the Monument field. The wells in this area were relatively small, because of decreased porosity in the lime. The greatest activity in Lea County was in the Monument pool, with 199 completions, 197 being oil wells, one a gas well and one a dry hole.

Jan 1, 1938

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

By Fred D. DeVaney

MINNESOTA taconites are extremely hard, and fine grinding is required to produce an acceptable concentrate. To reduce grinding costs, waste material is rejected by magnetic separators as soon as it is liberated. Cyclones are now used in all Minnesota taconite plants to close the grinding circuits. Erie Mining Co. installed its first grinding section at Aurora, Minn., in 1948-a 9 ½ x12-ft. mill and a fine grinding section consisting of a 10 ½ x12-ft ball mill in closed circuit with a duplex 60-in. spiral classifier. Concentrates from the magnetic cobbers treating the rod mill discharge passed directly into the classifier; the ball mill discharge was also treated in magnetic separators and the concentrate from these machines also went to the spiral classifier. Both concentrates passed through ac demagnetizing coils. It is axiomatic that for proper classification the material in suspension must be well dispersed, and it follows that magnetic concentrate must be almost completely depolarized if classification is to be successful.

Jan 8, 1957

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may' be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By A. Aly Selim

A computer model was developed to calculate the fragmentation cost for in situ leaching operations as a function of the blast design and deposit parameters. The model is based on blasting an ore zone only or an ore zone plus overburden by either a coyote blast or a vertical blasthole system. The model calculates the blast design parameters and the fragmentation cost based either on a user input powder factor value or on a powder factor calculated by the model as a function of the overburden height and the ore zone thickness. Examples of blast design parameters calculated by the model are the number and spacing of blastholes for a vertical blasthole system and the number and spacing of crosscuts for a coyote system. The model also calculates the total amount of explosives, the detonating cord length, and the number of primers. The cost of blasthole drilling can be calculated by the model based either on purchasing and operating a drill or on a user input value of the contracted cost of drilling. Application of the model to an example ore deposit showed that the vertical blasthole systems were more economical than the coyote system when there was no overburden and the deposit had an average ore thickness less than 45 meters. With no overburden and ore thickness greater than 45 meters, the vertical blasthole system was either more or less expensive than the coyote system depending on the number of levels used in the coyote system. With overburden, the coyote system was less expensive than the vertical blasthole system for blasting either the ore only or the ore plus the overburden. A coyote blast will usually produce larger particle sizes than a vertical blasthole system. Larger particle sizes can result in lower copper recoveries so that a less expensive coyote blast may not improve the overall economics of an in situ leaching operation. Blasting the ore zone only was generally less expensive than blasting the ore plus the overburden by either blasting system. Also, for the example considered, the coyote system costs were less sensitive to changes in overburden thickness and powder factor while the vertical blasthole system costs were less sensitive to changes in ore thickness.

Jan 1, 1977

By Frederick Bacorn

THE paper of Reno H.. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were, acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept.

Jan 8, 1914

By N. Christensen, B. Augland, T. H. Johansen

Samples of an Fe-Nb alloy were brought to equilibriurtr with hydrogen-methane mixtures in the temperature range from 950° to 1050°C, and subsequently analyzed on their carbon contents. The solubility pvoduct L = [%Nb] [%C] may be represented by the equation Approximate solubilities indirectly assessed through hardness measurements have been included from a previous report. These data are shown to be in a fair agreement with the present solubility measurements. IN an investigation based on hardness measurements by de Kazinczy, Ms, and pachleitnerl the molal heat of solution of NbC was estimated to 11.5 kcal per mole. This value was considered rather small, and an investigation using a similar technique was carried out. The results indicated a heat of solution about 35 kcal per mole.2 At this stage it was decided to determine the solubility under conditions of true equilibrium . During the course of this work a similar investigation was published by Smith. 3 His heat of solution, 41.6 kcal per mole, is not very different from the value resulting from the present work (42.5 kcal per mole). Our solubility product, on the other hand, is at considerable variance with that reported by Smith. Possible reasons for these differences are discussed below. Mori, Tokizane, and saheki 7 have studied the behavior of niobium in commercial steels, with special attention to the formation of niobium carbide, nitride, and sulfide. Assuming a carbide composition Nbco.87 based on X-ray diffraction and chemical analysis of residues extracted from Fe-Nb-C-S alloys, the molal heat of solution of niobium carbide was estimated to 35.2 kcal per mole. MATERIALS AND EQUIPMENT The chemical analysis of the materials is given in Table I. Electrolytic iron* was used in the preparation of

Jan 1, 1968

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By I. D. Shah

A roasting procedure for synthetic copper sulfide which results in a reproducible transient melting at 450° and 470°C is described in this paper. Possible causes for this melting phenomenon are suggested, and also a procedure to avoid it during the roasting. This melting is believed to be responsible for the occasional occurrence of stickiness in the commercial roasting of copper sulfide concentrate. Many workers have studied the roasting of copper sulfides, but only Lewis et al. have reported that fusion and, in some cases, fusion with "boiling" occurred in the neighborhood of 450°C. The DTA and TGA apparatus, the materials used in this investigation, and the discussion of chemical reactions occurring during the CuS roasting are described in an earlier publication. CuS, in the form of either pellet or powder, was heated at 280° to 330°C in a flowing air or 30% 02: 70% N2 atmosphere. Heating was continued at this temperature until no further weight increase due to sulfates formation was observed on the TGA thermogram. This is believed to be due to the inability of SO, to diffuse out from the sulfate layer on the surface of the pellet, thus halting the sulfate-forming reactions. Hereafter, the sample oxidized in this manner will be referred to as "partially oxidized CuS." X-ray analysis and microscopic examination of a polished cross section of a partially oxidized CuS pellet showed the following order of layers starting from the center of the pellet: Cu2S, Cu2O, CuO • CUSO4, and CuSO4. A bare thermocouple inserted in the center of a partially oxidized CuS pellet (2.5 g) did not indicate any noticeable change in the temperature of the pellet when melted at 450° to 470°C in an inert or oxidizing atmosphere. During the preparation of a partially oxidized pellet, the temperature of a CuS pellet increased by 50°C due to the exothermic formation of sulfates in air at 320°C. The endothermic peak associated with the melting phenomenon at 450°C is shown in [Fig. 1.] A CuS pellet (0.2 g) was oxidized in flowing air (150 cc per min) at 10°C per min up to 320°C and held there for about 2 hr. Then, N2 replaced air and heating was continued up to 500°C. The exothermic peak at 320°C represents an overall formation of sulfates, and an endothermic peak at 450° to 470°C represents the melting phenomenon. To observe the melting visually, a small (50 mg), partially oxidized CuS pellet was heated (in static air) in a hot-stage microscope. The melting phenomenon was observed on an auxiliary TV screen. The sample

Jan 1, 1976

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By E. H. Griswold

The many complexities arising from our present oil pool proration systems emphasize the need for a suitable standard of property rights. Attempts at conservation and unitization agreements have frequently failed because of the lack of such a standard. The necessity of reducing production to consumption has caused umpires, committees, commissions and other governing bodies to allocate the production of flush fields among the respective owners. The methods of allocation vary widely and conservation of underground reserves is frequently neglected or misused. Critical economic conditions increase, rather than modify, competitive methods. In some fields we have irregular and uneconomically close well spacing. Many operators drill unreasonably large holes, take excessive sand penetrations or leave their wells untubed in order to secure higher potential open-flow tests than their offsets. All of these practices result in economic waste and frequently damage to the pool. Regardless of our agreement with the fundamental principles of proration or unitization, both are actual necessities in many of our present economic situations, and we are in urgent need of a suitable standard of rights to facilitate and simplify their operation. The problems pertinent to unit management are simple and of daily use in many partnership enterprises, but the problems of fair and proper division of production under either proration or unitization are, as yet, subject to controversy. The rights of respective owners must be ascertained and standardized before we can eliminate wasteful practices and still preserve constructive competition in our industry. Valuation of Tracts In a recent unitization conference it was found that each participant had a different basis for calculating the relative values of tracts. Some of these assumptions were as follows: 1. Unrestricted open-flow operation to abandonment. 2. Current proration system to abandonment.

Jan 1, 1933