Search Documents

By L. S. Reid, Irwin Politziner F. M. Townsend

Recently published data indicate that the water vapor content of a gas, as determined by dew point measurement, is inaccurate when the gas has been dehydrated with diethylene glycol. Water vapor contents and dew point measurements of gases dehydrated with triethylene glycol have been obtained in this investigation in order to determine the magnitude of a similar error, if one exists. Experimental data show a very low concentration of triethylene glycol vapor in gases dehydrated at atmospheric ternperatures and pressures ranging from 500 to 2,500 psia and that the accuracy of dew point measurements is not impaired by the presence of triethylene glycol vapor. INTRODUCTION Nearly all natural gas transported by pipe line to northern and eastern markets must be dehydrated to a low residual moisture content in order to assure maximum transmission efficiency and continuous delivery under peak load conditions. Without dehydration, water vapor often condenses in pipe lines in quantities sufficient to restrict the flow3 and. under low atmospheric temperature conditions, gas hydrates may form and plug gathering. transmission and distribution facilities. Gas may be dehydrated to pipe line specifications by a number of methods. The most widely used methods are (1) adsorption of water vapor on a solid dessicant such as activated bauxite, alumina or silica gel,' (2) by absorption of water vapor by either diethylene or triethylene glycol-water solutions of high glycol concentration,11,13 and (3) by simultaneous expansion-refrigeration of very high pressure gas in which gas hydrates are purposely formed and then quickly decomposed.'"" Of these three fundamental methods, the adsorption and absorption processes provide the bulk of the dehydrated gas moving to market at the present time. The expansion-refrigeration process. a relatively new development, is gaining in favor because of its simplicity but is sharply limited in its application by available differentials between source and gathering system pressures. Where gas sale or purchase contracts contain a maximum water vapor content specification, the water vapor content is usually determined by measuring the dew point of the gas at system pressure. Knowing he dew point temperature and the system pressure, the water vapor content of the gas is determined from a graphical correlation of saturation, or dew point, temperature us the water vapor content of the gas which is customarily expressed as pounds of water vapor per million cubic feet of gas measured at 14.7 psia and 60°F. Dew points are usually measured with the U. S. Bureau of Mines Dew Point Tester. shown in Fig. 1, which is well suited for use at temperatures lower than 120°F and at pressurei; ranging from atmospheric to 3,000 psi. A number of correlations of dew point temperatures vs water vapor content are available,3,5,15 the most recent of which is that by McCarthy et al.4 Where natural gas is dehydrated by absorhing contact with concentrated diethylene glycol-water solutions. considerable difficulty is experienced in observing water dew points due to condensation of liquid hydrocarbon and glycol films on the mirrored surface of the dew point tester. Riesenfeld and Frazierl2 report that the dew point method for determining the water vapor content of a dietllylene glycol-treated natural gas is in error due to the glycol content of the condensate formed on the tester mirror, and that the water vapor content of the gas tested is actually lower than that indicated by the standard' dew point-water vapor content correlation. Extensive experience in testing gases dehydrated by concentrated triethylene glycol-water solutions lias not revesled difficulties of the nature cited above for diethylene glycol. Water dew points are clear and sharp and condensation of

Jan 1, 1951

By Glenn Allen

SAN FRANCISCO Mines of Mexico, Ltd. owns and operates an extensive group of claims in the San Francisco del Oro-Santa Barbara district, about 15 miles southwest of Parral, Chihuahua. The property comprises the mines, aerial tramways, flotation mill, power plant, shops, offices, assay and testing laboratories, modern hospital, water and sanitary system, quarters for miners, mechanics and operators, a well housed colony for Mexican staff employees and residences for foreigners. Each colony has a club house and mess and tennis courts. The employees have constructed a nine-hole golf course. In other words, the property is self-contained and completely integrated for production of lead and zinc concentrates from complex sulfide ores.

Jan 1, 1930

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970

By N. H. Jensen

SINCE the sixties, Utah has been one of the leading metal mining states of the Union. During the last fifteen years its mines have supported the largest smelting center in the world. Its rank as a metal producing state is reflected by its 1924 production which had a value in excess of $65,000,000 making it the leading silver producing state, third in both copper and lead and sixth in gold production. During the past year, metallurgical developments for the recovery of zinc contained in lead ores has made rapid progress so that the future zinc output will be of substantial importance. The largest silver mines of the nation and the world's largest open cut copper mine are within its borders. Settlement of Utah started in 1847, with the advent of the "Mormons," and originally the area of the state was much greater than now. The first metal mining

Jan 1, 1925

NEW MEMBERS The following list comprises the names of those persons who became members during the period of July 10, 1917, to Aug. 10, 1917. ARNOT, STANLEY L., Engr., Plymouth Cons. Gold Mines; Ltd., Plymouth, Amador Co .2 Cal. BARRETT, LESLIE PARK, Asst. Geol.... Michigan Geological Survey, Lansing, Mich. BENNIE, JOHN WILLIS Gen'l. Mgr., Shannon Copper Co., Clifton, Ariz. BRINTON, OWEN FUGATE Mgr., Admiralty Zinc Co., Quapaw, Okla. BRODERMANN, JORGE, Civil Engr., Compania Minera San Francisco, Havana,Cuba. BROWN, RICHARD HENRY JR., Sales Engr., Ingersoll Rand Co., 300 N. Broadway, St. Louis, Mo. BROWN, STANLEY Chile Exploration Co., Chuquicamata, Chile. BUDDECKE, WILLIAM A Pres., Point Milling & Mfg., Co. Mineral Point, Mo. BURGESS, GEORGE K., Physicist and Chief, Division of Metallurgy, Bureau of Standards, Washington, D. C.

Jan 9, 1917

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable for subsequent precipitation of Ni and Cu by H,

Jan 3, 1955

By N. H. van Lingen

A laboratory stud], has been made to determine what factors affect the penetration rate of roller bits, diamond bits and drag bits in rock drilling with clay /water muds. The rather simple relations that exist when pressures in and around the borehole are equal become more conzplicated when under down-hole conditions the penetration rate is hampered by the existence of a pressure differential between the mud at the hole bottom and the pore liquid at cutting depth. Expressions that have been derived for both the penetration rate and the magnitude of the pressure differential in permeable rock together fully account for operating, rock, mud and bit variables. In impermeable rock a similar pressure differential is caused by the bit action itself. In all cases, the pressure difierential and the reduction in penetration rate increase with the effectiveness of the plastering at the bottom of the hole by mud particles. Where bits are employed whose action is largely that of crushing, however, the plastering may become even more effective owing to the addition of rock particles rubbed into the pores of the rock. With roller bits, a plastically hehaving layer may be formed, which causes a further reduction in penetration. In the case of bits whose action is chiefly scraping, moreover, penetration may be arrested by the bit's becoming balled-up. The various adverse effects are reduced by thorough scavenging of the hole bottom. This paper shows how with jet bits the efficiency of such scavenging may he improved by suitable choice of the position of the nozzles. INTRODUCTION The reduction in a bit's penetration rate with increasing depth of hole has been the subject of many investigations. Various investigators ',' have independently reached the conclusion that this reduction occurs not so much because the rock-breaking process becomes more difficult as it does because the lifting of the rock fragments is impaired by a fluid pressure differential holding the fragments down. When such a pressure differential can be avoided, as in air drilling and to a smaller extent in water drilling, penetration rates remain high. Although the range of applicability of these techniques is being extended, most oil wells still have to be drilled with mud. In this paper we present the results of laboratory experiments carried out to determine what factors govern the hold down effect encountered in mud drilling. In the course of this investigation, the well known importance of bottom scavenging came more and more into prominence. Not only may it reduce the magnitude of the hold-down forces, but also it appeared to be a means of preventing the accumulation of a plastic mass of cuttings and mud on the hole bottom and bit which may cause penetration to cease almost completely. So that the effects of fluid pressures may be more readily understood, the factors that govern penetration rate in the absence of these pressures will first be discussed. The effect of down-hole pressures will then be assessed for the case of permeable rock where fluid pressures are well defined, and it will be demonstrated how rock strengthening due to confining can be accounted for. Subsequently, fluid pressures in less-permeable rock will be examined; we will show that in impermeable rock it is the bit action that governs fluid-pressure distribution and hold-down. In the case of poor scavenging and/or high bit load. cutting cake manifests itself. The effect, like various others. appears to depend on the type of bit used. From the very beginning, therefore, we shall base our discussion on the three main types of bits used in rotary oil-well drilling— roller bits, diamond bits and drag bits. Since space is limited, it will be impossible to make more than a passing reference to many aspects of the problem. Moreover. certain relations that are not of primary irnportance to our argument will unavoidably have to be stated in a somewhat dogmatic fashion, and the experimental data on which these are based necessarily must be omitted. EQUIPMENT The drilling experiments were performed on three machines, of which one has been designed for the realistic simulation of down-hole pressure conditions. HIGH-PRESSURES MACHINE In this machine (diagramed in Fig. 1) the mud, pore and confining pressures can all be adjusted independently. The foil-covered rock sample contained in the inner pressure vessel is confined by oil that is pressurized by means of a hand pump. The pore space of the watersaturated sample is connected to an arrangement which keeps the pressure in the pore space constant regardless of the rate of filtrate flow through the sample.

By J. S. Fulton

THOSE who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangement, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartment septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries) ; portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. PHASES Of the many papers published on various phases of the Bessemer process, nearly 170 according to one bibliography, over go per cent were concerned with the metallurgical phase and less than 10 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to one of the causes of the Bessemer process. Is it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By F. Peter

Technical progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating-and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.' The object of metallurgical furnaces is either to fuse the material charged or to bring it to a high temperature required for further mechanical manipulation. Leaving out of consideration for the present the reverberatory fusion-furnaces, we have to do with the heating-furnaces employed in connection with rolls, hammers, or hydraulic presses. The temperature to which the material must be

Jan 1, 1914

By William A. Bassett

Two very intense sources of electromagnetic radiation are contributing significantly to experimental studies of minerals at high pressures and temperatures: 1) A Q-switched YAG laser is able to produce a pulse of infrared radiation capable of heating a sample under pressures up to 400 kbar in a diamond cell up to temperatures in excess of 4000°C. 2) X-rays from the Cornell High Energy Synchrotron Source (CHESS) are used to obtain diffraction patterns of samples In a diamond cell in less than two minutes, patterns that would require hundreds of hours on a conventional source. The laser heating technique is being used to study the pressure-temperature conditions over which the melting of diamond takes place. In the initial stages of this investigation, diamond has been melted and techniques for detecting the melting have been developed. The intense X-rays from the synchrotron source have been used to examine the mechanism and rate of the pressure-induced phase transformation in Fe2Si04.

Jan 1, 1985

By H. W. Camp

The past year has had no revolutionary change in the process of petroleum refining, although there have been improvements and developments in practically every phase of operation, due largely, perhaps, to economic pressure. A few years ago, a Mid-Continent skimming plant using 35 gravity crude obtained 28 per cent. gasoline and naphtha; 9 per cent. kerosene, and the remaining yield gave gas oil and fuel oil. Figuring manufacturing cost, but not including sales, transportation, overhead and depreciation, the realization was $1.45 per bbl. of crude. Today, a thoroughly modern and up-to-date skimming plant, having all latest equipment, shows a realization of $1.74 per bbl. on the same basis. Thus it is evident that progressive developments have taken place in the last 2 or 3 years when potential earnings have been increased about 20 per cent. The average refiner is compelled to exert his utmost ingenuity in order to operate with a profitable margin. He has two factors to consider—recovery of maximum yields of profitable oils and the reduction of operating expenses. For the past 8 years, the margin between price of gasoline and cost of crude has grown narrower, constantly. Both these prices are determined by external conditions and not by the refiner himself, but the refiner might have been able to increase that margin had he more carefully controlled his output, limiting his production of light oils to current consumption. Be that as it may, this same economic pressure has given impetus to progress in improvements of primary distillation equipment, including stills, towers and heat-saving devices. A pipe still and bubble cap fractionating equipment can now replace a battery of shell stills, giving better yields, better control, elimination of rerunning and lowering of operating costs. The most recent pipe stills are being equipped either with radiant-heat furnaces or air-preheating systems and improved heat exchange equipment. These can be operated on a fuel consumption as low as 1 per cent. of the charge as compared to a fuel consumption of

Jan 1, 1929

By Maurice Cook

A procedure of obtaining specimens of lead, tin, and cadmium with a moderately equiaxed structure and a smooth surface suitable for etching without grinding and polishing is described; the advantages of general oblique illumination (as opposed to vertical illumination) in the photomicrography of pure metals .are stated. Using these methods, a statistical study of the changes brought about in deformed lead, on annealing, has been made. The common mode of structural change was found to be recrystallization. Cases of growth of one original grain into another were rare; but if a totally recrystallized specimen was annealed above 200° C., a few large grains appeared and spread over the whole area, except for a certain number of small grains which remain unabsorbed. The temperature needed to produce structural change in lead was found to be lower, the greater the degree of deformation. With tin, an extension of 28 per cent. caused practically no recrystallization at ordinary temperatures, but recrystallization occurred if the specimen was heated to 100° C. In cadmium at low temperatures, the grain size decreased in marked manner as the deformation increased; but at high annealing temperatures, the grain size was comparatively independent of the degree of deformation. THE structural changes in metals brought about by annealing following a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum,1 tungsten,2 iron,3 copper,4 gold,5

Jan 11, 1924

By F. Peter

I. GENERAL INTRODUCTION. TECHNICAL progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and. revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating- and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.'

Jan 12, 1913

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By H. B. Kinnear

THE first copper stool used under an ingot mold to receive molten steel has recently been taken out of service after it had received ingots amounting to 6012 gross tons. This stool, weighing 8330 lb. had been in continuous service for 1822 heats since its installation. From this modest beginning the use of copper for ingot-mold stools grew to 425,000 lb. in 1934, with an additional 50,000 lb. of copper used in the form of inserts in cast-iron stools. During 1935 the quantity of copper used for stools increased by about 350,000 lb., making a total of 775,000 lb. now in use for that purpose. Copper used for inserts has increased during this time 180,000 lb., or over 350 per cent, to a total of 230,000 lb. The total of copper, therefore, in use at present under ingot molds is slightly over 1.000,000 lb.

Jan 1, 1936

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912

By T. T. Read

JAPAN'S iron and steel industry has always been closely connected with military strategy. Many years ago it became evident that the country's iron-ore resources were too small to support any extensive industry. As a result a belief in the imperative necessity of securing such resources has influenced Japan's political and economic policy in the Far East. Iron-ore developments in China are too well known to need repeating except to note that they have been rather unsatisfactory to both China and Japan. The ore deposit at Tayeh, in China, is not as large as was first believed and, though that and other sources of supply in China proper are now furnishing Japan a little more than a million tons of ore yearly, it cannot be counted upon as a large permanent source of supply. The deposit in Shantung proved so disappointing on further exploration that operations there have, so far as I know, long since ended. The operations at Pen-bsi-hu, in South Manchuria, which C. F. Wang de¬scribed in the A.I.M.E. TRANSACTIONS for 1918, Vol. 59, were reported to have yielded 84,000 tons of pig iron in 1928 and about 50,000 in 1935, so they seem to be going back.

Jan 1, 1937

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962