Search Documents

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee' studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.' Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By F. W. Hillnhutter

In plant tests with a 9.7 m hearth diameter high top pressure blast furnace the influence of disintegration of sinter during low-temperature reduction on blast furnace performance was evaluated. The blast furnace burden during the test period consisted of 74% self-fluxing sinter with a basicity of CaO/Si02 = 1.3, 15% pellets, 6% lump ore, and 5% recirculated slags. The sinter for the test was produced in a modern sinter plant. By changing the fuel rate and/or the MgO content at a constant basicity CaO/Si02 sinters with different low-temperature disintegration properties could be produced. The blast furnace was equipped with pressure monitoring devices at medium height of the furnace stack wall. This device provided in addition to the normal operating data readings of pressure losses in the upper and lower part of the furnace. The basic physico-chemical factors determining low-temperature disintegration are explained. The testing devices and the extent of quality control measures of sinter during the test period are outlined. Conclusions are drawn from the plant test in relation to sinter properties.

Jan 1, 1977

By G. Ferrara

The reserves of lead and zinc ores in the metalliferous district of Iglesias in south-western Sardinia are today estimated at about 30 million tons, grading from 4 to 10% Pb + Zn. Of these reserves, about 40% are in the mines owned by AMMI Sarda S.p.A. The working of these resources goes back to ancient times. Not infrequently, traces of old Roman workings and remains of ancient implements are come upon in the higher parts of some of the ore bodies. Exploitation of these mines on larger scale, however, dates from the middle of the 18th century. Initially, the more accessible zones of the ore bodies and the richer ores were worked - the galena and the rich oxidized ores (calamine* with 25-35% Zn), which were often found in large masses, the enormous empty cavities of which still remain. The poorer grade deposits have been gradually rendered workable by the development of technology - the perfecting of the

Jan 1, 1970

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.' Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.'. The same condition exists in such sand-tones as the Jones Sand at Shuler' and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.', ' Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines' where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By PHILIP N. MOORE

IT is a pleasure to realize even at that day the dignity of the engineer&apos;s calling was upheld. May I also add my firm belief that today there be many engineers who will qualify to the specifications of our interesting author. Since that time, the development of the world has been chiefly due to the engineer, and so far as human brain can foresee, the material tasks of the future will continue to follow the directions of his judgment. Popular opinion says this is the age of the engineer; literature, which in the long run, voices public sentiment, shows it in the number of engineers who figure as characters of fiction. The engineer has been doing the big things necessary to increase the comfort and efficiency of mankind, but while a certain amount of fame and repute falls to him, too often he figures as the hired man of the entrepreneur, using that term not in the offensive sense of a mere promoter, but to mean the great visioned master of enterprise who has seen ahead of other men, recognized the coming needs of the world, and through ability to inspire others and to hire capital for his use has also been able to hire engineers as needed. Justly enough, therefore, to such men comes the fame as well as the prize of the game.

Jan 1, 1926

By Ross Blake

THE St. Joseph Lead Co. became interested in the Tri-State district in 1921 through acquisition of prospecting and development rights on approximately 20,000 acres of land extending northeastward from the Picher mining field, mostly in Kansas. Prospecting with churn drills was begun the same year and the first commercial ore body was found on the Jarrett tract at the then northern limit of the main Picher field. Operations at this mine began in 1923. Kansas Explorations, Inc., was organized in 1923 by the St. Joseph Lead Co. as a wholly-owned subsidiary to carry on its operations in the Tri-State District from an office at Joplin, Mo. As prospecting of the original acreage proved largely negative, attention was subsequently turned to other sections of the district. Numerous additional leases were acquired and prospected. The Company was successful in developing into operating properties the Jarrett, Isherwood, Robinson, Sullivan and Lotson tracts and, in more recent years, the Ritz, Snapp, Buckingham, Gibson and Jasper mines.

Jan 1, 1947

A. H. Bromly, Zihuatanejo, Guerrero, Mexico (communication to the Secretary*):—The following criticism of what "is offered as a summary which may be found useful by mining engineers," is not dictated by any captious spirit, but in the intereet of historical and scientific accuracy. The States of Queretaro and Oaxaca have produced sufficient silver to warrant more extended notice. Referring to Pachuca, State of Hidalgo, the eomewhat loose and inexact statement is made that "the ore-depdsit is an andesite, intermixed with quartz-veins, rich from the surface." A better description mould be,—the ore-deposits consist of quartz-veins in andesite. It is notable that many of the rich shoots worked in recent days did not come to surface. In consequence, Pachuca is often quoted by the ill-informed as a camp in which values improve with depth, the truth being that the veins carry shoots, or clavos, some of which were exposed at surface and some not. The name of " electric plow," applied to the mechanical stirrer of recent use, is certainly not to be recommended. The stirrer, or agitator, consists essentially of a traversing gang-plow, operated by power through shafting; drums, and wire-rope. The fact that in certain plants the motive-power used is electricity does not make it an electric plow. Such a name suggests a machine of which the motor is an essential and integral part; which is not so in this case. A lathe in a factory driven by water-power is not called a hydraulic lathe. My experience agrees with Dr. Raymond&apos;s note as to azulapue, which in some districts is also applied to blue copper carbonate. The El Oro, Esperanza, and Mexico mines should be allocated to the State of Mexico; the Dos Estrellas being in Michoacan, as stated. The El Oro quartz certainly does not appeal to me

Jan 1, 1910

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By F. O. Willhofft

The symposium on mine safety held in connection with the annual meeting of the Institute three years ago, it. was pointed out that "at present no convenient, reliable, accurate means for determining the gas content of mine air is available, for use by the ordinary mine man." In a letter addressed to Coal Age and published on Feb. 25, 1925, Thomas T. Read, then Director of the Safety Service of the Bureau of Mines, stated: "It is to be hoped that sometime in the near future some-one will invent a reliable methane indicator that is con-venient to, use and will permit the keeping of all flames of every character out of bituminous mines, through doing away with the safety lamp." The Martienssen methane detector, which has re-cently received the official approval of the Bureau of Mines, is intended to. meet the demand for such an in-strument as expressed at that meeting and on many other occasions. The characteristics which qualify it for the task are the following: (1) simplicity; (2) small bulk and light weight; (3) ruggedness; (4) accuracy sufficient for the requirements; (5) safety; and (6) dependability. The principle on which the working of the instrument is based may best be explained by giving a brief out-line of the various stages of development through which the inventor, Professor Martienssen of the University of Kiel, Germany, advanced to the final solution of the problem which he had undertaken to solve.

Jan 2, 1928

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of &apos;these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By AIME AIME

TEXAS not only produces millions of barrels of petroleum daily, but supplies the oil industry with an asset infinitely more valuable than liquld gold. That asset is leadership. The oil industry was built from its humble beginning a few decades ago into a potent force in world economy by human hands and human brains. One of these great leaders in the busy world of oil is Wallace Pratt, of the Humble company, who has been called to a position as director and member of the executive committee of the Standard Oil of New Jersey. So reads the Houston Post of June 3, 1937.

Jan 1, 1944

The recent dedication of Magma Copper Co.&apos;s San Manuel, Ariz., electrolytic copper refinery and rod casting plant marks the culmination of a three year, $250 million expansion-modernization program. The new facilities will eventually permit an annual production of 200,000 tons of marketable copper for direct sale to fabricators. The Newmont Mining Corp. subsidiary will produce and market continuous cast 5/16 in. copper redraw rod, full plate cathode copper and sheared cathode plate under its own brand name. Among the four largest in the nation, the new refinery and plant, was built at a cost of $34 million and will be fully automated. In addition, all materials used in the plant will be recycled and no waste, discard or emissions will occur.

Jan 3, 1972

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary&apos;) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945