Search Documents

By Lars Thomassen, Ernest Kirkendall, Clair Upthegrove

THE amount of research done in the last few years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Desch1 in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for its review and bibliography is an article by A. I. Krynitsky.3 While considerable material has appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined at three temperatures. PROCEDURE The method used consisted of plating copper on a beta brass, heating it to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the temperature at which diffusion takes place the beta brass is saturated with copper. Thus, while the beta brass supplies the zinc, no diffusion takes

Jan 1, 1938

By A. Perry Thompson

I- GeneRal Distribution, AppeaRance, and Relations ........ 563 11. Data fRom MicRoscopic Examination............... 568 1. Criteria for Distinguishing Primary from Secondary Minerals...... 568 2. The Leonard Vein Filling..................... 574 Quartz............................ 575 Pyrite............................ 575 Enargite............................ 576 Covellite............................ 578 Bornite............................ 581 Chalcocite........................... 583 Chalcopyrite.......................... 586 3. The Fault-Vein Covellite..................... 587 The Speculator Ore........................ 587 The East Gray Rock Ore.....,.............. 589 4. Other Occurrences of Covellite.................. 591 111. Conclusions........................... 592 1. The Replacement of Minerals..................592 2. The Character of Mineralizing Solutions .............. 594 I. General Distribution, Appearance, and Relations Mining in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,' it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 1, 1916

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By Ernest R. Woakes

Cana, originally called Santa Cruz de Cana, is situated in the province of Darien, in the Republic of Colombia, S. A. The river Cana is a tributary of the Tuyra, which flows into the Gulf of San Miguel, and thence into the Pacific Ocean some 80 rniles S.E. of the City of Panama. • The Espiritu Santo mine lies on the S. side of the Cana river at the foot of the Espiritu Santo range. The plateau of Cana has an elevation of 2000 feet above sea-level, and the mine is about 200 feet above the plateau. The map of the Darien accompanying this paper is the only correct one in existence. It was made by Lucien N. Bonaparte Wyse for the Panama Canal Co., and has been copied fur the present use, with permission, by Mr. L. G. Inglis. The dotted line on this map shows the route from the coast to Cana. As this mine was one of the most celebrated at the time of the Spanish occupation, it is only natural that there are a great many traditions and writings concerning its former workers and production. Dampier mentions it, though he does not seem to have been nearer to it than El Real de Santa Maria, the port on the Rio Tuyra, about 50 miles by road from Cana. Senor Vicente Restrepo's work, entitled Estudio sobre las Minas de Oro y Plata de Colombia, translated by C. TV. Fisher and published in New York in 1886, is, perhaps, the best treatise on Colombian mines. He has devoted a great deal of attention to the subject of the Espiritu Santo mine, and has had access to all that dealt with it in the archives of Bogota. It will be interesting to quote a few pasaages from the above work, which seemed like a romance to the writer of this paper some years ago, when he first came across the history. Being actually in Cana at the time, and knowing the present company had

Jan 1, 1900

By AIME AIME

APPARENTLY unperturbed by any misgiving as to ill luck connected with the mystic number thirteen -for there were exactly that number of Directors on deck-the Board held two sessions on Tuesday, Feb. 21. , . Between the executive session at 5:15 p. m. and the general session at 8:30 p. m., 28 Section and Division delegates were wests of the Directors at dinner. Committee chair- " men and past officers brought the attendance to 75. Messrs. McAuliffe, Merica, Mudd and Tally had expressed their intention to be at the Directors' meeting, but each was prevented unavoidably at the last minute. At the executive session of the Board, J. V. W. Reynders was unanimously chosen to fill the unexpired term of Dr. Becket as Director: and Eugene McAuliffe in like " manner was selected to become Vice-president to fill the vacancy created hy Dr. Becket's assumption of the Presidency. Upon nomination of President Becket the following Executive Committee was appointed: Frederick M. Becket, chairman; Howard N. Eavenson, H. A. Guess, J. V. W. Reynders and William Wraith; and the Finance Committee was appointed as follows: Henry Krumb, chairman; Paul D. Merica and H. G. Moulton. Karl Eilers was reelected Treasurer and A. B. Parsons was re- elected Secretary to serve for the ensuing year, whereupon the executive session was adjourned.

Jan 1, 1933

By LESTER H. WOOLSEY

IT IS doubtful whether anything new can be said upon this subject and, therefore, it is with considerable hesitation that l prepare this paper. On account of my recent connection with the Department of State as its law- officer, perhaps I will be pardoned if I discuss this subject briefly from the point of view of that branch of the Government. , I cannot, of course, speak for that department, since I have-no connection with it at-present, but it may be helpful if I set down certain* of the factors which in my opinion and from my experience have a bearing on this international problem. With oil-burning ships, motor vessels, motor vehicles, airplanes-all consuming, astonishing quantities of petroleum or petroleum products; with the United States having within its borders only 12 per cent. of the petroleum resources of the world, and consuming about 70 per cent. of the world's output; with the more enterprising nations wide awake to the necessity ; of obtaining and preserving as large a share as possible of the oil resources extant ; the 'problem is peculiarly and in a, very practical sense an international one.

Jan 1, 1921

By B. M. Larsen

IN endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary importance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a clear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carbon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. REACTION RATES AT STEELMAKING TEMPERATURES General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase -that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: I. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrin1 has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjusted immediately. 3. Barret, Holbrook and Woods observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By A. E. Wells, H. O. Hofman, R. P. Reynolds

A Discussion of the Paper of H. O. Hofman, R. P. Reynolds and A. E. Wells, read by title at the London Meeting, July, 1906 ; presented at the New York Meeting, April, 1907, and printed in Bi-Monthly Bulletin, No. 13, January, 1907, pp. 37 to 52. GEORGE A. PACKARD, Boston, Mass. (communication to the Secretary*) :-The very interesting results obtained by Prof. Hofman and his assistants came to my attention when I had temporarily assumed charge of the metallurgical department of the Missouri School of Mines, and had found it, pending the completion of a new building, lacking a furnace in which to roast ore preparatory to the customary lead blast-furnace run. An attempt at lime-roasting had been already determined upon, but the use of a charge which would make a slag of definite composition was a new idea. The results following were obtained by Messrs. Aubrey Fellows, J. C. Long, E. R. Wash, and Dr. T. C. Tseung, under my supervision. It is regretted that the data are not more complete; but the work was done simply incidentally to securing the desired ore for the blast-furnace, with no idea of obtaining any results of especial interest. It is submitted because of the metallic lead obtained, no notice of which has been seen elsewhere. The ore was an aggregate of several lots of concentrates, apparently from Missouri ores. The analysis follows, with that of the limestone and sandstone used, as far as made:. Ore, SiO2, 3.04; Fe, 0.77; CaO, 2.53; Pb, 68.74; Zn, 5.77; S, 13.9 per cent.; limestone, SiO2, 1.0 ; CaO, 54.35 per cent.; sandstone, SiO2, 99.8 per cent. The converter was made in the shops from a sheet of No. 14 iron riveted in the shape of a truncated cone, 20 in. in diameter at the top, 15 in. at the bottom and 22 in. high. A grate of No. 8 iron, 17 in. in diameter, with 130 s-in. holes placed at about 1.25-in. centers, was held in place by the shape of the

Jul 1, 1907

By R. C. Ferguson, B. Bernstrom

R.C. Ferguson (District Manager, Hardinge Company Inc., Hibbing, Minn.) — In the opening paragraph of Mr. Bernstrom's paper he stated that the Cascade mill performance information is preliminary. With the completion of the 1962 operating season, more reliable performance information became available. The main bearings, which had been damaged, were reconditioned at the factory. New Gatke bearing bushings with a 120° are of contact were supplied. Provision was made to introduce high pressure lubricant at two points in each bearing. New spherical bearing balls that operate in spherical seats were aligned at the factory and held in place by several setscrews to aid in installing the bearings in the field. The screws were not loosened prior to, or during, operation; therefore, the bearings operated as rigid bearings. The lubricant cooling system was changed to the cooling tower type to provide lubricating water of a suitable temperature. Another refinement consisted of installing a device to add a set percentage of soluble oil to the make-up water.

Jan 1, 1963

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

By D. E. Moore

The strength of a natural serpentinite gouge was measured at 400°C and an effective pressure of 100 MPa. The strength of the gouge decreased with increasing pore pressure to 50 MPa and then was nearly constant between 50 and 125 MPa. The samples at 50-125 MPa pore pressure slid stably, whereas those at 3-25 MPa pore pressure showed stick-slip behavior. Lengthening the pre-heating time to 72,000 s of samples at 100 MPa pore pressure led to increases in both the strength and the likelihood of sliding unstably. With still longer pre-heating times, the strengths decreased again and sliding once more became stable. The strength of the gouge at 3 MPa pore pressure was unaffected by changes in pre-heating time. A possible explanation for the results is that excess pore pressures are being generated in the gouge, causing the true effective pressure to be lower than the apparent value.

Jan 1, 1984

R. F. McELVENNY.- The next item is: "Center and other methods, vs. side charging." That was all discussed in the Carson case, and I do not know but what many of the plants are still using center charging. Some are using side charging. Did I understand that where you use the wet charge it is all side charging on the wet ore? B.-G. C. HONEYMAN.- We were on center charging for about a year with wet ore. R. F. McELVENNY.- Then you went to side charging. Has anyone any remarks to make on side versus center charging? E. A. BARNARD.- We have one side and one center, both on deep bath. It is an experimental proposition so far, but the side charge looks very favorable.. R. F. McELVENNY.- This is with calcine? E. A. BARNARD.- This is with calcine on a floating charge proposition.. They are both water jacket. The charge acts very similar on both center and side charging. The calcine spreads much the same as it does on the center charge. It will run down 75 ft. on the furnace side as well as the center. The advantage is in taking care of secondaries and things of that nature. C. BARDWELL.- Do you get any side wall protection from it? E. A. BARNARD.- No. R. F. McKENZIE.- Do you not project the side wall up to protect the skewback? E. A. BARNARD.- There is a slot projection down around the top of the bath; but the repairs on the side wall have been practically the same; that is, they, have been practically the same as they have on the center charge. A. H. RICHARDS.- A point I would like to make is that if you have any doubt about the center charging, we feel that we get better tonnages and lower fuel ratios and better slags with center charging than we ever got with side. Different kinds of charges would, of course, vary, and I could readily see that if you had the same advantage with deep bath smelting that you mention you would probably get just as good a slag and as good fuel ratios. E. A. BARNARD.- In fact, I think the calcine charge spreads more on the side than on the center charge. A. H. RICHARDS.- If you maintain a deep bath. E. A. BARNARD.- That is one thing we have to be careful about, to hold the charge back.

Jan 1, 1930

By W. H. Durrell

DISCOVERY of large iron ore deposits in New Quebec and Labrador is, undoubtedly, one of the outstanding mining events of the twentieth century. To give an idea of size, the present concession is almost equivalent to a strip a mile wide around the earth at the equator. Importance of this iron ore area can best be appreciated by comparison to the famous Mesabi Range. On Mesabi, the area of favorable rock is 110 miles long and from 1 to 5 miles wide, with a, productive zone about 70 miles long. On the con- cessions the area of favorable rock in the Labrador Trough is 225 miles long and from 10 to 60 miles wide. In Quebec-Labrador, exploration already discloses that the productive zone is 90 miles long, with good chances of being extended at both ends. The Mesabi is covered generally by thick over- burden, and the iron ore deposits were found by T- test-pitting and systematic test-drilling. In Labrador and Quebec, most ore has been developed from a few surface deposits, and when it is considered that at least 95 pct of the area is covered by over- burden, and that there remains thousands of square miles of favorable territory still to be explored, it can be seen that the possibilities for developing additional ore are tremendous.

Jan 4, 1954

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By W. P. Blake

Forty-five years have passed since I discovered the extensive and remarkable diatom-earth beds at Monterey, California., and now I have the satisfaction of bringing to notice still another wonderful deposit in the heart of Arizona. The Monterey beds mere described at the Philadelphia Academy,* and specimens were sent to Prof. J. W. Bailey, West Point, N. Y., at that time the leading American authority upon such microscopic relics of organic life. The earth from both localities is snow-white and pulverulent. It rubs off' like soft chalk upon the fingers when handled, and has the general appearance of chalk. But, unlike the Monterey beds, these newly-discovered deposits consist largely of volcanic ash, through which the siliceous shells of the diatoms are distributed. These deposits are in the central portion of the San Pedro valley,† in the southeastern corner of Pinal county. The region of their greatest development is a few miles south of the mining town of Mammoth, on the east bank of the stream, and near Redington, some 40 m. N. of Benson, on the Southern Pacific railway. The altitude is about 2600 ft. above tide. This portion of the San Pedro valley lies between the high Catalina and Rincon ranges on the west and the Galiuro mts. on the east. The Catalinas are composed chiefly of crystalline DIRECTOR OF THE ARIZONA SCHOOL OF WINES,

Jan 1, 1903

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.'-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962

By Harold R. Larson, John F. Elliott

The standard free energies of formation of several nzetallic sulfides have been measured by a reversible electromotive-force cell employing stabilized zir-conia as the electrolyte. The oxygen potential at the cathode was fixed by the use of pure oxygen gas at 1 atm. It was established at the anode by bringing to equilibrium the reaction between the sulfide and oxide species present. Thus, Gf: for the sulfide could be obtained from the cell potential and the standard free energies of formation of the oxides participating in the reaction. The results in calories per cam rnole for the temperature range 850" to 1100°C are: Use of the reversible electromotive-force cell having an oxide-ion electrolyte to obtain the standard free energies of formation of some of the more stable metallic sulfides offers a convenient experimental method that is very productive. It also avoids some of the problems inherent in the experimental methods' for such studies which rely on precise determination of gas compositions, particularly if these compositions lie near the limits of our capabilities for accurate chemical analyses. The reaction equilibrium between the lowest sulfide of a metal, SO2 at a fixed pressure, and an oxide of the metal has a characteristic oxygen potential. For example: and for metals whose lowest sulfide is much more stable than the oxides of the metal, the equivalent reaction might be:

Jan 1, 1968

By Leon W. Dupuy

INTRODUCTION A BRIEF elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kind or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico 1-4 during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. SELECTION OF METHOD OF DRILLING Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. FACTORS GOVERNING SELECTION OF DIAMOND DRILLING The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1947