Search Documents

By M. H. Merriss

IN THE last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: In the series system, the electrodes in a single tank are in series, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 6, 1925

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."' * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,' and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956

By A. J. Langhammer

Broadly speaking, it may be said that the engineer has two major responsibilities: One is to recommend the choosing of proper machinery and equipment; the other, to assist in the simplification of design, determination of method, and advise about the most suitable material to be used. The products of powder metallurgy enter broadly into both these fields. The oil-cushion, self-lubricating bearing surface on a machine part makes for better machinery and factory equipment, often proves a life-saver in curing difficulties where bearings are overloaded or inaccessible for lubrication, or on installations that with normal practice constitute a problem entailing frequent repairs. On the other hand, other parts may require low porosity approaching solidity. In the second field, powder metallurgy provides many possibilities for improved products, improved performance, solving of technical problems, saving of weight, quiet operation, higher factors of safety, greater flexibility, attractive economies, and so on. Parts We of the automotive industries are making many powdered-metal war-machine parts, both ferrous and nonferrous, including gears, external and internal; ratchets, both external and internal; levers; pillow blocks; sliding blocks; cams; gibs; hubs with external and internal splines, and similar units. Powdered metals play an important part in our war work, as they did in peacetime in the manufacturing of passenger cars and trucks. The art of powder metallurgy is not a panacea. Although on certain parts such operations as turning, boring, facing, reaming, counterboring, milling, countersinking. chamfering, broaching, hobbing, profiling. trepanning, gear cutting, grinding, etc., can be eliminated, there will always be the need for machine tools. Advantages of Powder Metallurgy Simple machining operations often are eliminated by using powdered metal, and also many other intricate operations, some of which are of the type impossible to perform on the most modern production equipment; for instance, an external spline on a flange hub, where the spline must continue to the flange face and at full depth. Another important feature is that some of the machine parts may require a self-lubricating surface at one or more points; for example, proper lubrication of a sliding splined spool, while ordinarily most digcuit, is accomplished automatically with a self-lubricating powdered-metal bearing. Frequently machine parts are made with physical, mechanical and technological advantages unobtainable from cast or forged metals of similar analysis. Thus powder metallurgy offers the designing engineer broader latitude. Similarly, the engineer may take advantage of powder metallurgy in his teamwork with other departments. Another important advantage in powder metallurgy for machine parts is the relatively short time required for tool-up.

Jan 1, 1945

By O. Katz, A. Spilners, M. Simnad

THE oxidation of titanium has been studied in recent years by a number of investigators.'-W ne of the most important aspects of the reaction of titanium with oxygen, which has been observed by several of the investigators, is the extremely high solubility of oxygen in the metal. A detailed study of the Ti-0 systeml% as shown that the solubility limit of oxygen in a-titanium is approximately 14.5 wt pct 0 from 800" to 1700°C. The unusual oxidation behavior of titanium may be ascribed to this phenomenon, since part of the oxygen uptake enters into solid solution in the metal and only a part is available for scale formation. A more complete study of the kinetics of oxidation of titanium would require information on the influence of oxygen in solution in the metal upon the oxidation rate. Such information would also be of interest in regard to the theory of oxidation of metals. The authors have measured the oxidation rates of oxygen-saturated and oxygen-free titanium between 800" and 1200°C and have found appreciable differences in their rates of oxygen uptake and in the activation energies. The experimental set-up was similar to that described in a previous paper.u The course of oxida-dation was followed continously by attaching the specimen to a sensitive spring balance and observing the extension of the spring with time of oxidation. High purity electrolytic oxygen was used and precautions were taken to purify the gases employed. The specimens were prepared from iodide titanium and were ground on metallographic polishing papers to a fineness of 4/0. The furnace was first evacuated and filled with argon; the specimen was lowered into the furnace, which was then evacuated and filled with oxygen, after the specimen had reached the oxidation temperature in argon. The samples were presaturated with oxygen by means of the following procedure: Each specimen was first heated in oxygen at 1200°C until its increase in weight indicated 13.8 pct by weight uptake of oxygen. The furnace was then immediately evacuated and filled with purified argon five times. The specimen was heated in the argon atmosphere for a period of 72 hr at 1200°C in order to saturate the metal with oxygen by complete absorption of the scale. The temperature was lowered to the oxidation temperature, the furnace was evacuated and filled with oxygen, and the oxidation rate was followed by noting the extension of the spring balance. No oxide film was visible on these specimens at the start of the oxidation experiments. Titanium samples in the oxygen-free as-received condition were also oxidized and their oxidation rates measured. The results are shown in Figs. 1, 2, and 3, which indicate that the initial rates of uptake of oxygen by both the oxygen-saturated and oxygen-free specimens are parabolic at these temperatures. The rate of uptake of oxygen is, however, appreciably lower

Jan 1, 1956

By P. Somasundaran

INTRODUCTION Large amounts of mineral values are discarded today as fines and ultrafines, because of inadequate technology to process them economically. Most conventional mineral processing techniques fail in the sub-sieve range. Fines respond poorly to processes such as flotation either due to change in mineralogy and surface composition or even simply due to the direct effect of their smallness in size on collision and adhesion rates between them and air bubbles. Indeed if the poor flotation is due to the smallness in size, a solution must rest in aggregating the fines. Inorganic electrolytes as well as polymers have been successfully used as flocculants in the past for obtaining increased flotation of colloidal material from waste water effluents. In mineral beneficiation, this technique can be profitably used if the process of flocculation can be made to take place selectively. The power of the selective flocculation technique has already been proven, with the successful application of it in the case of beneficiation of low grade iron ore by the Cleveland-Cliffs Iron Ore Company and potash ore by Cominco. The process holds tremendous potential when it is followed by flotation, elutriation, etc. Today its application is, however, limited to the above two cases and it has become clear that a full understanding of the process will prove helpful for developing solutions to various problems that exist both at the basic and applied levels. In this paper, principles that are known to govern selective aggregation processes such as selective flocculation, carrier flotation and spherical agglomeration will be examined and areas of uncertainties will be identified.

Jan 1, 1979

By M. R. Todd, J. Szekely

THE mechanism of carbon oxidation in steelmaking processes has attracted considerable attention in recent years. The generally accepted model postulates that the reaction between carbon and oxygen occurs at the surface of CO bubbles that originate at the suitable nucleation points and subsequently rise through the metal bath.1-4 Although this model describes adequately the behavior of open-hearth type operations, it is not a satisfactory representation of carbon oxidation in oxygen steelmaking processes since it cannot account for either: i) the very high rate of oxidation per unit bath area,or ii) the commonly reported shapes of the curves showing the dependenie of the oxidation rate on the carbon concentration. The very high decarburization rates commonly encountered in oxygen steelmaking processes need no further elaboration; some typical plots of the rate of carbon removal against carbon concentration, taken from a publication by Li, Dukelow, and smith,' are reproduced in Fig. 1. It is seen from the curves that the decarburization tends to decrease from a peak or a plateau once the carbon concentration falls below a certain value; in the experiments reported, this critical value ranged from 1.2 to 0.2 wt pct C. The apparent dependence of the decarburization rate on the carbon concentration indicates that within this region phenomena associated with the transfer of car- bon must play an important if not predominant role. Since the concentration of oxygen in molten iron at steelmaking temperatures (removed from the immediate impact zone) is only about 0.1 wt pct,6 it is clear that simple simultaneous diffusion of carbon and oxygen to the surface of CO bubbles could not account for the rate of carbon transfer being the controlling step at carbon concentrations as high as 1.0 wt pct. The purpose of this communication is to present an alternative model which may explain at least qualitatively the apparent anomalies mentioned and may stimulate further experimental work. The Physical Model. It is suggested that the principal mechanism of decarburization is the reaction between CO bubbles and an emulsion consisting of molten iron and molten iron oxide particles in the vicinity of the "slag-metal interface9'.* This mech-

Jan 1, 1968

By Carl W. Volz

NORWAY'S metallurgical development, which has extended over many centuries, is intimately associated with that country's unique topography and climatic conditions. It is a rugged mountainous country, with a most irregular shore line, bordered by thousands of islands forming a natural protection for shipping. There are an endless number of lakes, and innumerable rivers and waterfalls, many fed by glaciers and melting snow. Rainfall is abundant. Though half of the country is north of the Arctic Circle, it is warmed by the Gulf Stream, so that the average temperature is about 45°, or 20° higher than other parts of the world in the same latitude. A sub-

Jan 1, 1935

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By R. J. Colony

MINING geology does not lend itself - very readily to a review embracing "improvements in methods," as perhaps do shop practices or laboratory procedures. The "methods" used in mining geology are simply the application of geology to mining; winning the ore, the handling of material, mechanical appliances, all belong strictly to mining proper, and have no place in a review of geology as applied to mining. A comprehensive review would necessarily cover a .very broad field, which could be subdivided into many -parts. Only a few of these can be discussed here. .Those that have been suggested to the chairman indude :

Jan 1, 1930

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By A. Bar-Or, G. Hirsch, P. Wynblatt

The rates of nucleation and growth at various temperatures in U-0.45, 1.1, and 1.35 at. pet Cr alloys were determined, providing a qliantitative proo-f that the transformation under study is controlled by nucleation and diffusional growth. The linear relationship, log NV US 1/T2, suggests that the nucleation of the alloys is probably controlled by the classical law of nuclei formation. The established linear relationship, log G us 1/T, in the three alloys suggests that growth in each alloy is controlled by bidimensional nuclei formation. It was established that both the rate of growth and the rale of nucleation are retarded by chromium. Using classical formulae, sApN and sApG (the ß/a apparent interphase energies) were calculated from the nucleation and growth results, respectively. It was found that their values are of the same order of magnitude. However, why sApN is unaffected by the addition of chromium, while sApG increases with it, needs further clarification. In the last few years, an appreciable amount of research has been conducted into the mechanism of the ß —a transformation in uranium and uranium alloys. Recently, Burke1 reviewed the published work concerned with this transformation. He concluded that in dilute uranium alloys it is firmly established that, at high temperatures in the a range, ß decomposes by a diffusional process. However, he based his conclusion either on experiments dealing with the over-all transformation,2 or on qualitative results.3 It was felt that a better insight into the mechanism of transformation could be gained from the quantitative measurements of growth and nucleation rates, which we aimed to carry out in the present work. In a previous work,4 we have shown that a rim of a grains is formed during isothermal transformation at the high a range. The thickening of this rim with time was used for measuring the rate of growth in U-0.45 at. pet Cr.5 This method was also used in the present work for two more alloys. For meas- uring the rate of nucleation, a method of quenching and macroetching was developed to allow differentiation between a grains formed during isothermal transformation at the upper a range and those formed after quenching, Fig. 1. EXPERIMENTAL WORK AND RESULTS The Rate of Nucleation. The measurement of the rate of nucleation was effected by counting the num-

Jan 1, 1965

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By F. E. Harris

It has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-'. If the term used for carbon concentration is weight Pet C, as is customary, then a factor must be found, changing this term to One of weight Per unit volume when the diffusion coeficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expresses all evaluation of unsteady flow whereby D is given a relationship with the numerical value of C-x slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-x curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. KO such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. The Steady State Diffusion of Carbon in Au~tenite The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.' For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the Center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase: carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid ment down towards its steady state value. At points well removed from the ends, the concentration will remain the Same along planes parallel to the surfaces of the plate.

Jan 1, 1948

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs' scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By R. H. Jamison

A relatively new haulage system is described. Employed by the Delmant Fuel Co.. the "Full Dimension" system provides an uninterrupted flow of coal from a loader or continuous miner at the face to the main line transportation system. This system is said to provide a higher percentage of recovery as well as additional safety and production. Delmont Fuel Co. is employing a comparatively new system of transportation known as a Full Dimension system. Cne of these systems has been in operation for a year at the company's 10-B Mine as a part of a conventional section. A second was installed at the No. 10 mine in late 1960 to handle the production of a Colmol in a pillar section. SYSTEM COMPONENTS A Full Dimension system is a haulage system that provides an uninterrupted flow of coal from a loader or continuous miner at the face to the main line transportation system. The equipment required for this system consists of a series of interconnected chain conveyors that are mobile and articulated. They will retract or extend a sufficient distance for the development of a five-entry system; or, in the Colmol pillar section, it provides reach of 210 ft in all directions from the section belt. The components of this system are: l)One 160-ft chain line placed in tandem with the belt conveyor. It has a self-propelled drive, is 20 in. wide and 9 in. deep. Moving this conveyor requires the assistance of a loading machine or cutting machine. 2) One 40-ft piggyback that discharges along the entire length of the 160 ft chain conveyor. 3) A mobile bridge carrier, which is a self-propelled conveyor with four wheel steer and four wheel drive, twenty-eight feet long, it delivers coal to the receiving end of the piggyback. Axles steer individually making possible almost lateral movement. 4) Another 40-ft piggyback, duplicate of item 2 that delivers coal along the entire length of item 3 (mobile bridge carrier). 5) A second mobile bridge carrier, similar to the first, which deliver coal to the piggyback (item 4). 6) A third 40-ft piggyback, duplicate of items 2 and 4. This pig is attached to the loading machine and delivers its coal along the length of the second mobile bridge conveyor. Since the original preparation of this paper, the Delmot Fuel Co. has been able to eliminate the 160-ft chain conveyor. This was accomplished by connecting the outby piggyback directly to a loading machine with an extended boom. The loading machine loads directly onto the belt. This change has resulted in a substantial reduction in moving time and greatly increased flexability. A single trailing cable powers the entire string of equipment. It is attached to the side of the equipment in such a way as to keep it off the ground and afford maximum protection. The tramming rate of this equipment is 90 fpm. The conveyor capacity in a conventional section at Delmont's mines is 7.5 tpm and in the Colmol section is 5.5 tpm. This regulation is a simple function of conveyor speed. To visualize operation of this equipment, it would be well for me to touch briefly on local conditions in the Upper Freeport seam in which we mine. (Also, see the photographs of some of the equipment in use.) DELMONT'S TOPOGRAPHY The Delmont Fuel Co. operates two mines in this seam in Westmoreland County, Pa. The No. 10 mine, which was opened in about 1912, is now almost worked out. Depending on economics in the industry, it has a life of two to four years on a declining production basis. A year ago a new drift mine was opened which is called No. 10-B. It is about two miles from the cleaning plant and is connected thereto by an overland belt conveyor. The new mine is being developed at a rate calculated to take up the slack as the old mine plays out. The Upper Freeport seam averages 4.2 ft in thickness in the area of the Delmont mines. It carries 4 in. of boney coal at the top of the seam and a middle man of from 2 to 4 in. We mine just above a 1-in. slate parting which has 4 to 6 in. of highly laminated coal beneath it. This material normally makes a very firm bottom. The roof varies from dark shale to sand rock and 36-in. bolts are placed on 4-ft centers for roof support. All working places are driven 20 ft wide on development and 25 ft wide on retreat. Selection of mobile chain conveyor equipment when it became available, was a very natural move for Delmont Fuel to make, because chain conveyors and piggybacks had been in use at the company's mines for about 12 years. Grades in the new mine

Jan 1, 1961

By H. R. Banks

The Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. Original Flotation Equipment and Ore The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.P.m. The impellers were the 45' type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling go per cent made up of 13.6 per cent galena, 14.4 per cent mar-matite, I per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between IS and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. Special Features of Flotation at Sullivan Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed. This operating condition is mentioned because it is the author's belief that the in-

Jan 1, 1947