Search Documents

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By W. R. Crane

DRAINAGE in these mines has been discussed in papers, on mining practice,1 but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions; and consideration of means of improving the conditions. While conditions are not serious, yet there is danger that they may become worse if present mining practice is continued, owing to the presence of formations, known to carry large quantities of water, that overlie the ore bed worked. Much detailed information has been collected regarding: rainfall, and run-off in streams draining the district; the effect of different kinds of formations, porous and non-porous; the inclination of the surface; the condition of the surface above the mines, i. e., whether or not disturbed by ground movement; the occurrence of the ore and character of associated formations, particularly with respect to presence of jointing or slip planes, faults, etc.; failure of top rock in the old stopes; and the conditions under which water effects entrance into the mines, i. e., whether as a natural or forced flow. The study furnished fundamental data on the source of waters now entering the mines and that which may later enter due to collapse of top formations in. abandoned workings. The presence of jointing, or slip planes, has a pronounced influence upon the whole drainage problem. These present lines of least resistance to the water and, by weakening the top formations, cause fracturing of the overlying rock, allowing both surface and deep-seated waters to enter the mines.

Jan 1, 1927

By Dever C. Ashmead

COAL companies in the anthracite region are studying various methods of mining that will permit a considerably shorter life of gangway and therefore a decrease in the maintenance charges. Maintenance charges in the upkeep of gangways where the measures are steeply pitching are high due to the excessive cost of the replacement of timbers and the cleaning up of falls. Therefore, if the length of gangway in the coal beds can be decreased and the mining more concentrated, the life of the coal gangways will be decreased and consequently the maintenance charges will be lower per ton of coal produced. Customary practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced.

Jan 1, 1925

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By Lawrence B. Wright

The Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 fol1owing installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticliue and a cross anticline recumbent against Cretaceous granodiorite. and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to ore-making materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937 The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about I to 4 and in the disseminated and breccia ores, I to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene. Introduction The Republic district of north central Washington is of new interest because of the discovery, development and extraction of new gold-silver ore; also, because of a unique local structural pattern believed to be integral with the broader tectonic mechanism of the continental framework. This district had 40 years of modest rating following its discovery in 1896. Its narrow ore bodies, complex mineralogy. and early inadequate metallurgy, together with the apparent bottoming of ore near 1000 ft, limited production to 300,000 oz of gold and 1,000,000 oz silver between 1897 and 1914. The camp was then reduced to lease Life until 1937, when the gold price increase of 1933 to $35 per ounce

Jan 1, 1949

By Lawrence B. Wright

The Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 fol1owing installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticliue and a cross anticline recumbent against Cretaceous granodiorite. and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to ore-making materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937 The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about I to 4 and in the disseminated and breccia ores, I to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene. Introduction The Republic district of north central Washington is of new interest because of the discovery, development and extraction of new gold-silver ore; also, because of a unique local structural pattern believed to be integral with the broader tectonic mechanism of the continental framework. This district had 40 years of modest rating following its discovery in 1896. Its narrow ore bodies, complex mineralogy. and early inadequate metallurgy, together with the apparent bottoming of ore near 1000 ft, limited production to 300,000 oz of gold and 1,000,000 oz silver between 1897 and 1914. The camp was then reduced to lease Life until 1937, when the gold price increase of 1933 to $35 per ounce

Jan 1, 1949

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By AIME AIME

JANUARY saw the completion of the 237-ft. Upper-Narrows hydraulic debris dam on the main Yuba River in northern California. This project which is the key unit in a series of four similar structures on the Bear, American, and Yuba Rivers, removes the last obstacle to the revival of California's vast hydraulic gold-mining industry. The Upper-Narrows dam is a single-arch type of structure, and embodies the latest developments in that type of construction. One of the principal innovations used is the series of air vents in the crown (that part over which the water spills) which serve to break the vacuum caused by the spilling water, thus reducing vibration to a minimum. Electric strain gages were also embedded in the concrete of the dam, and it is hoped that by careful study of these instruments true stresses can he determined.

Jan 1, 1941

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

By Fred D. Fox

INTRODUCTION Approximately two years have elapsed since the first summary of the Grizzly Gulch Tailings Disposal Project was presented (1). Since that time, various physical modifications and additions to the existing treatment system have transpired. Further, Homestake and the entire mining industry have been impacted severely by additional modifications and additions concerning regulatory reform aimed at total disciplinary permitting and hazardous waste management. The following paper summarizes the past accomplishments relating to the Grizzly Gulch Tailings Disposal Project, correlating these accomplishments with future plans that are being developed to comply with regulations and to continue Homestake's commitment to environmental protection. The famous Homestake Gold Mine, located in Lead, South Dakota, has been operating in the Black Hills region for over a century, approximately 12 years before the south half of Dakota Territory was admitted to the Union as the State of South Dakota (2). During the 104 years of operational development, Homestake's Gold Mine, as well as the entire mining industry, have been influenced by numerous governmental regulations dating back to the Refuse Act of 1899 which regulated the deposit of debris from mines and stamp works. The enactment of the National Environmental Policy Act of 1969 may be thought of as the beginning of a long line of unplanned steps to deal with the many concerns of matters pertaining to the environment. Environmental awareness continued into the 1970’s, in which the Clean Air Act, Federal Water Pollution Control Act, Safe Drinking Water Act, Toxic Substances Control Act, and the Resource Conservation and Recovery Act (RCRA), to name a few, surfaced.

Jan 1, 1983

By D. W. Fuerstenau, G. D. Gumtz

Use of the discretized batch-grinding model for the simulation of locked-cycle grinding tests from batch-grinding data is illustrated. The simulated results were compared with actual locked-cycle experimental data for the dry grinding of dolomite. To illustrate the utility of this simulation method, a number of relationships between operating and performance parameters were generated, including relations between batch grinding and the Bond test, the production rate and the circulating load, and the production rate and the product size. A large amount of testing is done each year in the mineral industry for use with grinding unit cperations, and much of the experimental test data is obtained by the tedious locked-cycle testing procedure. In addition to being experimentally complex and requiring large amounts of sample, the very nature of the locked-cycle experiment yields results that cannot readily be interpreted. The attempts that have been made to model comminution systems during the last few years may provide a better and simpler way to obtain and analyze grinding test data; these models involve elements of both fitting to "model equations" and deterministic representations.1-1 The traditional engineering design techniques for comminution systems have relied mainly upon large amounts of industrial operating data that have been correlated with locked-cycle grinding data.',' Bond's empirical mill-design procedure involving locked cycle testing remains the most generally available method to this day. The purpose of the present paper is to show how much more useful data can be obtained from a simple batch-grinding experiment that provides information which subsequently can be utilized with population balance models of the grinding process to simulate locked-cycle behavior. These simulation results can, of course, be used in Bond's general design scheme. However, the combination of batch-grinding tests and the population balance model allows many more conditions to be considered than do single laboratory tests under specific locked-cycle conditions. The use of these simulation techniques for prediction of locked-cycle behavior represents one of the first practical applications for the simulation method in comminution.

Jan 1, 1971

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By Jay Carpenter

THIS paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator. This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with aTrent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. .These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and. delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 8, 1915

By W. E. Wickerham

THE Magnetic Storm Monitor is an instrument that continuously records variations in the earth's total magnetic field at a fixed location. It is intended for use in conjunction with airborne magnetometer surveys. There are stormy periods when changes in the earth's magnetic field are so violent that data obtained with airborne equipment would be of little value. The Monitor provides this information so that flights may be cancelled or terminated, thus eliminating useless flying. Moreover, when some unpredictable change in the earth's field occurs during an airborne survey, the Monitor record, showing a similar event, may serve to salvage the data. The utility of a base instrument is determined largely by its physical dimensions, power requirements, stability, and reliability. This instrument is small enough to be transported in any powered vehicle. It will operate from either a 110 v, 60 cycle power line or from an inverter powered by an automobile battery. The development of an electronic feedback circuit that measures the magnetic field strength and a fabricated buckout magnet having essentially zero temperature has contributed to instrument stability and reliability. A tripod supporting the magnetometer head, a chassis housing all electronic components, and an Esterline Angus Recorder comprise the equipment, shown in Fig. 1. The vibrator-type inverter shown is used when a 110 v, 60 cycle power line is inaccessible. Approxi- mately 60 w are required to operate the instrument and the circuit is insensitive to reasonable power line voltage changes or transients. The head unit contains a fluxgate-type magnetometer element and a special magnet mounted on a ceramic structure. Since this magnet is used to buck out most of the earth's field, adjustments are provided for properly positioning the magnet with respect to the element. This assembly is mounted in such a way that the element can be oriented into the total field. Fluxgate Element: The heart of the Storm Monitor is a fluxgate-type magnetometer element. The ability of this unit to detect changes in magnetic fields has been covered at length in the literature.1, 2 For this discussion it will suffice to say that the Gulf

Jan 1, 1956

By A. U. Seybolt

The solubility limit of oxygen in columbium has been determined in the range between 775' and 1100°C by means of lattice parameter measurements and microscopic examination. The solubility is a function of temperature and varies, in the range given above, from 0.25 to 1.0 pct O, respectively. BECAUSE of the marked deleterious effect of oxygen upon the mechanical properties of some of the transition metals, it is desirable to know something about the solubility of oxygen in these metals. The brittleness caused by oxygen in solution is particularly marked in the case of the group VA elements, vanadium, columbium, and tantalum. The solubility of oxygen in vanadium has already been reported in an earlier paper,' and Wasilewski2 has given a value (0.9 wt pct) for the solid solubility of oxygen in tantalum at 1050°C. Brauer3 in 1941 investigated the Cb-0 system up to Cb2O5, but made no real effort to investigate the extent of oxygen solubility in the metal. He made the observation, however, that this solubility must be less than 4.76 atom pct (0.86 wt pct) oxygen. This estimate was made from X-ray diffraction results on the alloys CbO, CbO, and CbO; all alloys consisted of the terminal (Cb) solid solution plus CbO, but the last alloy containing 4.76 atom pct 0 showed only three very weak CbO lines. It is surprising that Brauer, by examining only three alloys, arrived at an estimate of the solubility which agrees very well with the results to be reported herein. Experimental Procedure A columbium strip obtained from Fansteel Metallurgical Products was cut into strips, 0.020x1/2x2 in. Two holes, about 3/16 in. in diameter, were made near the ends of the strips in order to hold them against a flat steel block for mounting in a General Electric X-ray spectrometer for lattice parameter measurements. The same holes were used to hang the specimens inside a fused silica vacuum furnace tube which was part of a Sieverts' gas absorption apparatus. The apparatus and method of adding oxygen gas has been previously described.1 According to the supplier, the columbium obtained had the analysis given in Table I. After degreasing the samples, approximately 0.001 in. was etched from each side of the samples in order to remove possible surface impurities from the last rolling operation. For this purpose the following cold acid pickle was found satisfactory: 8 parts HNO3, 2 parts H2O2 and 1 part HF. Various Cb-O compositions were obtained up to 0.75 wt pct O by the gas absorption and diffusion technique. After the sample had absorbed all the oxygen gas added at 1000°C, an additional 24 hr was allowed for homogenization. This treatment appeared to be adequate, as shown by the linearity of the lattice parameter-composition plot. More concentrated alloys were prepared by arc melting mixtures of Cb and Cb2O5 since it was very time-consuming to make Cb-0 alloys in the neighborhood of 1 pct O, or over, by the diffusion method. When the flat strip specimens were used, they were ready for the X-ray spectrometer after cooling from the Sieverts' apparatus. The cooling rate obtained by merely allowing the hot fused silica furnace tube to radiate to the atmosphere (when the furnace was lowered) was sufficiently fast to keep the dissolved oxygen in solution. Arc-melted alloys were reduced to —200 mesh powder in a diamond mortar, wrapped in tantalum foil, sealed off in evacuated fused silica tubes, and then heat treated as indicated in Table 11. The fused silica tubes were quickly immersed in cold water without breaking the tubes after the heat treatments. The tantalum foil prevented reaction between the fused silica and the sample; there was no reaction between the powdered samples and the foil at 1000°C, but some trouble was experienced at 1100°C. At this temperature level a reaction between the sample and the foil was sometimes observed, which resulted in erroneous parameter values. Experimental Results Hardness Tests: Since most of the X-ray samples were in the form of flat strip, it was convenient to obtain Vickers hardness numbers as a function of oxygen content. Compared to the V-O case,' oxygen hardens columbium much more slowly, presumably because of the larger octahedral volume in colum-bium (about 12.0 compared to 9.3Å3 in vanadium), hence, requiring less lattice strain for solution. The plot of VHN vs wt pct O is shown in Fig. 1.

Jan 1, 1955

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970