Search Documents

By Donald R. Lessard

I. INTRODUCTION There is no question that the choice of an appropriate discount rate is a critical element in virtually all business decisions in extractive industries. The standard textbook approach relies on a single overall cost of capital for an entire firm, itself a weighted average of the firm's cost of debt and equity. But a single rate is appropriate only if the commercial risks and financing structures are similar for all projects under consideration. In extractive industries, appropriate discount rates are likely to vary greatly from project to project. Risks of projects differ markedly by mineral, by country in which the project is located, by stage in production, and by position in the project's life. Further, for a variety of institutional reasons, financing structures vary greatly in relation to these same variables and thus the discount rate appropriate to the entire investment and, in particular, to the sponsor's equity investment will vary even more markedly. Failure to select discount rates which reflect these differences can result in extremely distorted decisions. Our interest in this subject results from our ongoing research on alternative ownership and financing structures for large scale extractive ventures in less developed countries where risks to the various participants--the sponsors, the financiers, and the host government--vary dramatically with the different options. Given the magnitude of these differences, a single discount rate for all options is clearly inappropriate. However, there appear to be few guidelines for practicing managers to follow in setting appropriate rates. In this paper, we take a first step in this direction.

Jan 1, 1977

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author&apos;s values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author&apos;s can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author&apos;s reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By J. J. Gilman

RECENT experiments have shown that the mar-tensite reaction in a standard tool steel is influenced by the history of the reacting austenite. The martensite reaction proceeds to a given extent at a higher temperature in austenite formed from an annealed spheroidal structure than it does in austenite formed from tempered martensite: that is to say, a prequench lowers the temperature range of the martensite reaction in this steel. Furthermore, a prequench alters the appearance of the martensite as compared to martensite formed from "virgin" austenite. The steel used for this work was a manganese nondeforming tool steel of the following composition: C, 0.85 pct; Mn, 1.43; Si, 0.23; Ni, 0.12; Cr, 0.59; and W, 0.59. A piece from a rolled bar was forged to Vz in. sq and annealed to a spheroidal structure. Disks 1/8 in. thick were used in the experiments. Several sets of the specimens were prepared and austenitized in lead at 1475°F. Three sets were held at 1475°F for 15 min, quenched in water, and immediately reheated to 1475°F. After this quench the three sets were held for 5 min, 30 min, and 3 hr, respectively, at 1475°F and then the individual specimens in each set were quenched in molten baths to 325", 300°, and 275ºF, respectively, and held for 15 sec. Immediately after the quenching treatments? the specimens were tempered at 600°F for 30 sec to darken the martensite and then were quenched in water. The holding times were short enough to avoid isothermal transformation. Three other sets of specimens were given the same final quenching treatments as the first three, but they were austenitized at 1475°F for 20 min, 35 min, and 3 hr and 15 min, respectively, without an intermediate water quench. The two individual specimens from each set were quenched together in order to eliminate quenching errors. Several experiments were run in this way but only the six sets referred to are described in detail because they all yielded essentially the same results. By means of the stated heat treatments the martensite reaction was investigated for: 1—austenite formed from an annealed structure, and 2— austenite formed from tempered martensite. The martensite reactions of the two types of austenite differed significantly. This is shown by Figs. 1 and 2. Comparison of the photographs on the left in Figs. 1 and 2 with those on the right shows that less martensite was formed by a quench to a given temperature from prequenched austenite than from austenite formed from an annealed structure, that is, the prequench suppressed the martensite reaction. The effect was observed for specimens austenitized 20 min, 35 min, and 3 hr and 15 min. A comparison of Figs. 1 and 2 shows that the martensite reactions in both sets of specimens occurred at lower temperatures with increased austenitization time. This was caused by the increased dissolution of residual carbides with time at 1475°F. However, the difference in amount of martensite formed in prequenched austenite as compared to virgin austenite was approximately the same for all three austenitization times. One further observation should be noted. The needles of the martensite formed from virgin austenite are somewhat longer on the average and show less of a tendency to cluster than those of martensite formed from prequenched austenite. This causes the martensite on the right in Figs. 1 and 2 to have a more acicular appearance than the martensite on the left. Since the sets of specimens used in this work were austenitized for identical total lengths of time and the effect of a prequench on the martensite reaction existed for specimens held at the austenitizing tem-

Jan 1, 1953

Jan 1, 1969

By A. E. Zawadzki

A progress report is presented on the development of a process for the removal of sulfur dioxide from flue gases. Catalytic oxidation of the sulfur dioxide in flue gases, with the production of recoverable sulfuric acid, has been demonstrated to be technically feasible. Problems associated with the process are discussed. The need for an inexpensive and efficient process for controlling sulfur dioxide emissions from utility plant stacks has been accentuated by the ever-increasing public demand for elimination of all man-made air pollutants. I would like to describe the results of an investigation of the development of such a process; more important, I would like to present a discussion of the problems associated with the process which remain to be solved. The research work on the BCR catalytic gas phase oxidation process has been jointly sponsored by the Association of Edison Illuminating Cos., Edison Electric Inst. and Bituminous Coal Research, Inc., since 1958. However, work on SO2-pollution abatement was initiated by BCR in 1953. Tieman and Clymer,1 working with ozone and simulated flue gases, evaluated a gas phase oxidation process for removing SO2 from flue gases. Their experimental data indicated that the use of ozone to oxidize SO2 in flue gas concentrations, with subsequent recovery of H2SO4, did not appear to be economical due to the large ratio of ozone to sulfuric acid produced (2.6 to 1). The cost of the ozone would be 6 to 10 times the cost of sulfuric acid produced. As a result of the ozone study, work on a catalytic oxidation process was developed. The following reactions are the basis for the catalytic oxidation process Reaction [I] normally occurs in the combustion of sulfur-bearing fuels. At the high temperature found in the combustion chamber, 95% to 99% of the sulfur in the fuel is oxidized to SO2 and 1% to 5% is oxidized to SO3. The concentration of SO2 in the combustion gases depends on the combustion efficiency and the quantity of excess air used. A commonly used rule of thumb is 0.1 percent by volume SO2 in the flue gas for each 1% sulfur in the fuel. Reaction [2] proceeds at a wide range of temperatures. The rate of the reaction is rapid above l,000°F; however, the equilibrium conversion drops rapidly above this temperature. 2 Reaction [3] occurs rapidly to completion at temperatures below 400°F; above this temperature some SO3 exists in equilibrium with H2SO4. Complete dissociation of H2SO4 occurs above 650°F.3 The simplicity of the proposed process provided added incentive to the development and evaluation of the various component unit operations. The advantages of the process were considered to be as follows: 1) no raw materials were required, 2) the unit operations were not radically new; and 3) a salable product, sulfuric acid, would be produced. The successful development of the process was contingent upon the solution of several major problems: 1) The development of a catalyst which would provide high catalytic activity at reasonable conditions of gas flow and temperature without causing an unacceptable increase in pressure drop. 2) The development of a high temperature dust collection system to provide clean flue gases to the catalytic reactor. 3) The complete recovery of the sulfuric acid produced in the process; the effluent gas must contain less than 20 ppm by volume of sulfuric acid. As of this date, the complete solution to these problems has not been achieved. EXPERIMENTAL Catalyst Development: The use of platinum and vanadium catalysts for the production of sulfuric acid by the treatment of dry gases containing 5% to 20% by volume sulfur dioxide has been known for many years. The application of the basic idea of catalytic oxidation of sulfur dioxide in flue gas concentrations was

Jan 1, 1965

By Zay Jeffries

IT HAS been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat and cooling either rapidly or slowly with nearly pure iron and slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point, which is near 700° C. The present paper will not consider these old and well-known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, in 1886, reports that both working steel and heat treatment of steel in the blue-heat range are highly injurious. Recently, however, some metallurgists believe that the straightening of warped steel forgings at a blue heat produces a beneficial effect on the metal.2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes -in Iron and Steel Below the Thermal Critical Range, which has the following personnel: R. R. Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F.C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood: This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 2, 1920

By W. J. Reagan

A survey of the literature on bottom-cast practice gives but Scant information as to some of the real facts concerning this most int&apos;eresting method of steel manufacture, and some of the information available is very misleading. An exceptionally good description of this met,hod of pouring or teeming is to be found in an English publication2 on the heterogeneity of steel ingots. Quoting from this paper: (a) With bottom teeming, the metal rises steadily and progressively in the mold with the minimum possible agitation, the main force of the stream coming from the ladle being broken down or retarded by the down gate or runner. Further, the stream of metal from the ladle, under these conditions of casting, is invariably maintained at a much more continuous rate and is steadier than with top teeming. (b) In view of the facts referred to in (a) it follows that with bottom teeming the metal is not exposed to atmospheric oxidation to anything like the same degree as with top teeming. In this paper it is intended to detail briefly some of the advantages of bottom-cast practice and to discuss the possibilities of iron-oxide control in the basic open-hearth furnace. A description of the type of charge, ingot rnold set-up, etc., is found in detail in an earlier paper.3 Design of Ingot Molds In any kind of steel manufacture, ingot-mold design is important. L. H. Nelson4 lists in the order of their probable importance the following factors as influencing most the solidification of the ingot:

Jan 1, 1934

By John Chipman

Published data on the equilibria of carbon in binary Fe-C austenite with H2-CH4 and CO2-CO gas mixtures are used to obtain the constants of an equation repre -senting the activity coefficient of carbon throughout the stable austenite range of temperatutre mid compositiotl. Calculated values for the solubility of graphite are found to be in agreement with the best-published direct observations. Its heat of solution is 10,680 calper g-atom. The free energy of formation of cementite is culculated from the equilibrium compositions of austenite and of gas. Its entropy and heat of formation are also obtained. BASIC knowledge of the high-temperature properties and treatment of steels is contained in the Fe-C diagram and its extensions for the effects of alloying elements. The application of thermodynamics to the Fe-C system, with addition of alloying elements, can serve to simplify and systematize this knowledge. The points of beginning are the binary fee solution, austenite, concerning which our information is reasonably complete, and the binary carbide, cementite. Further studies must include the other phases of the binary system, a and liquid, and for these an accurate knowledge of the ? phase boundaries is essential. These studies should provide a firm base for systematic study of the effects of alloying elements on all phases of the system, their transformations, and precipitation phenomena. With the aid of the simplifying thermodynamic concepts of activity coefficients and interaction parameters it is to be hoped that the results of these studies will be amenable to computer solution thus making the information on multicomponent systems more readily available than would be possible in multidimensional diagrams. Studies of the thermodynamic properties of austenite have utilized equilibrium measurements on the reactions:

Jan 1, 1968

By P. R. Celmer, Leonard R. Weisberg

THE principle of fractional crystallization has been successfully used to prepare high-purity (99.999 pct) Ga. Hoffman and Scribnerl removed single crystals of gallium solidifying in a gallium melt, while Zimmerman2 grew single crystals from the melt by the Kyropolous technique. In contrast, attempts at purifying gallium by zone refining have been less successful. ichards, reported that despite the passage of 40 zones through a gallium ingot, there still remained 5 to 70 ppm each of Cu, Fe, Ca, Mg, Si, Al, and Ag. Previously, Detwiler and Fox4 detected only one impurity, Pb, segregating in zone-refined ingots. These surprising results prompted an investigation of the factors controlling impurity segregation in gallium. Possible reasons for this were insufficient diffusion of impurities in the melt; recontamination of the melt by its oxide film which is not affected by the passage of the zone; reaction of gallium with the boat; sudden freezing of gallium following supercooling, especially since gallium easily supercools to and trapping of impurities at grain boundaries. Impurity segregation tests were carried out by directionally freezing gallium using the Bridgman rnethd, modified in that the molten gallium is lowered out of a furnace into a slush of dry ice and trichloroethylene, thus minimizing supercooling. Since the gallium is contained vertically, the oxide film is in contact only with the tail end of the melt. It was found that Teflon makes an excellent crucible for gallium since it is quite pure, non-reactive, translucent, flexible, machinable, and is not wet by gallium. The gallium crystals could be grown at various speeds, and the melt could be vigorously stirred by a Teflon rod moving through the gallium in a vertical reciprocating fashion. Single crystals could be grown by placing a solid Teflon plug at the bottom of the melt drilled out in such a way to cause the solidifying gallium to follow a winding path. Thus, even if many crystals are originally nucleated, only one grain will predominate. The grain structure of the gallium crystals was revealed by an etchant composed of equal volumes of HC1, HNO3 and HF, diluted with water to half strength. Emission spectrographic analyses were carried out on samples removed from the front and tail ends of the resulting gallium ingots. Typical results of this study are summarized in Table I. The rate of freezing in all three cases was about 1 in. per hr. It can be seen that even though stirring of the melt does help, it is even more important to grow a single crystal of Ga in order to obtain good segregation of impurities. The effect of crys-tallinity on the segregation of impurities was previously observed6 in the directional freezing of germanium; however, in this case, the effect was much less pronounced. This dependence of impurity segregation on the crystalline perfection of Ga may be related to its thermal conductivity which is the most anisotropic of all metals.7 The anisotropic thermal conductivity can cause the solid-liquid interface to be nonuniform, thus leading to trapping of impurities during freeing, and therefore reduced segregation. In conclusion, it is indicated that zone refining of gallium would be more successful if seeding and similar precautions are taken to insure single crystal growth. The authors are indebted to Mr. H. H. Whitaker for the spectrographic analyses and to Drs. B. Abeles and F. D. Rosi for helpful advice and encouragement throughout the course of this work. This research was supported by the Electronics Research Directorate, Air Research and Development Command, under Contract No. AF33(616)-5029. REFERENCES &apos;J. 1. IToffmon and B. T. Scribrer: I. Research h&apos;atl. Bur. Standards, 1935, "01. 15, p. 205. &apos;W. Zirnmerman: Science, 1954, vol. 119, p. 41. %J. L. Richards: Nature, 1956, vol. 117, p. 182. &apos;D. P. Detwiler and W. M. Fox: I. Metals, 1955, "01. 7, p. 205. 5P. W. Bridgman, Proc. Am. ilcod. Sci., 1925, vul. 60, pp. 305,385,423. "S. L1. Christian: private c ommuni cation. &apos;K. W. Powell: roy. Sac., 1951, vol. 209, p. 525. &apos;W. G. Pfann: Zone Re fining, p. 20. John Wiley and Sons, Inc., New York, L058.

Jan 1, 1962

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult&apos;s law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman&apos; equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,&apos; Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell&apos;s value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1&apos; has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

Frank Williams, Johnstown, Pa. (Communicatioll to the Secretary): As the manager of the company which manufactured the " American " magnesite and the silica-brick mentioned by Mr. Pennock, I beg to say that he was quite right in placing a mark of interrogation after " American " (page 268). While the users of magnesite in this country are at a disadvantage as to cost by reason of not having any large bodies of sufficiently pure material at hand, the manufacturing concern referred to has secured an advantage as to quality by a mixture of the different foreign magnesites, which vary considerably in their composition and physical structure. The American (?) magilesite tested was a sample of the next

Jan 1, 1897

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien&apos;s article&apos; describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

By Arthur S. Wright

THE accuracy of the silver-assay depends in great measure upon a careful regulation of the heat of the muffle during the process of cupellation. At the beginning of the operation, a relatively high temperature is required to " open " the lead buttons, that is, to clear off the black film of oxide that covers the surface of the metal button immediately after fusion has taken place. The muffle is usually closed up until the buttons are uncovered. As soon as a clear, free surface of molten metal is exposed to the oxidizing action of the air, the temperature should immediately be lowered to the minimum temperature at which the formation and absorption of litharge can progress freely, and the buttons still be kept from " freezing." The process, under satisfactory conditions, will be characterized by the formation of rings of litharge crystals (" feathers," as they are styled), on the cupel, about the oxidizing globule; and the nearer these rings of litharge crystals call be made to approach the central oxidizing globule without interfering with the freedom of oxidation and absorption, the smaller will be the volatilization of silver, and consequeiltly the greater the degree of accuracy attained. This minimum heat must be maintained uniformly during the oxidation of the lead; and just as the last of the lead is disappearing, and the button is preparing to l blick," the temperature of the muffle should be allowed to rise so that the last traces of lead will be driven off. This regulation of the heat calls into play all the skill of the assayer, and requires a vigilant eye, able to distirlguish between the slightest variations of temperature of the muffle, assisted by a nice adjustment of fuel and draft. With a few cupels in the muffle at one time, the proper heat for each cupel can be maintained by roughly approximating the proper temperature, and then moving the cupels backward and forward in the muffle; but this is gene-

Jan 1, 1897

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the [&apos;tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the [&apos;tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By A. B. Johnson, J. S. Browning

The USBM has developed new and improved physical beneficiation techniques for economically recovering potash minerals from high-clay and low-grade ore from the Permian Basin of New Mexico. With the depletion of the high-grade ores a need for changes in industry&apos;s standard methods of recovery is a must. Technology may be improved in the beneficiation of the ore prior to mineral flotation and in brine clarification from the desliming phase to effect a reduction of losses of fine potash and brine in the disposal of the clay slimes. This report summarizes the results of these tests and demonstrates the feasibility of producing products that meet the requirements of the agriculture market, namely, 95% KCl equivalent to 60% K2O with recoveries ranging between 80 and 90%.

Jan 1, 1973

By R. R. Sayers

Ventilation may be defined as the process by which vitiated air of an enclosed or partly enclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level Per Cent. Oxygen.................................................. 20.94 Nitrogen................................................. 78.09 Carbon dioxide........................................... 0.03 Argon................................................... 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxide, ammonia, ozone........................................ traces Carbon Dioxide Limit For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent, carbon dioxide. Nevertheless, in mines it sometimes occurs in sufficient quantities to cause symptoms in men or even unconsciousness and death. One-half of 1 per cent. of carbon dioxide in normal air causes a slight and unnotice-able increase in the ventilation of the lungs, that is, a man exposed to one-ha,lf of 1 per cent. of carbon dioxide will breathe a little deeper and a little faster than when in pure air. If 2 per cent. of carbon dioxide is in the air, the lung ventilation will be increased about 50 per cent.; if there

Jan 1, 1927