Search Documents

By P. Marier, T. R. Ingraham

When anhydrous cupric sulfate is heated in a stream of nonreactive gas, cupric oxysulfate is formed. When this reaction is complete, the cupric oxysulfate then decomposes to cupric oxide, which is the normal end product of reaction. The kinetics of each of these reactions has been studied using pellets prepared from finely divided cupric sulfate and from finely divided cupric oxysulfate. In each case, the reactant-product interface within the pellet is well-defined, and by normalizing the decrease in inter facial area with the weight fraction of the pellet decomposed it has been shown that the interface migrates into the pellet at a uniform rate at constant temperature. The activation energy estirnated for the decomposition of cupric sulfate is 57 ± 7 kcal per mole and that for cupric oxysulfate is 67 ± 8 kcal per mole. The rate of interfacial reaction is flow-sensitive, increasing with increasing flow of a sweep gas in the range from 50 to 2000 cu cm per min. The rate of decomposition is retarded by sulphur trioxide in the sweep gas. The relationship between sulfur trioxide Partial pressure and rate is consistent with the Langmuir Adsorption Isotherm governing the retention of sulfur trioxide in the interfacial layer. MOST of the work reported on the thermal decomposition of cupric sulfate and of cupric oxysulfate is related to the thermodynamics of the individual decompositions.'-4 No information is available on the rates of the individual reactions, on their activation energies, or on the effects of gas flow or of partial pressure of sulfur trioxide on the reaction rates. Some dubious conclusions based on relative reaction rates have been drawn from studies on the oxidation of sulfides. For example, on the basis of the products observed in a quenched system, it has been suggested5" that, when copper sulfide is roasted, the cupric oxide which is formed arises from the decomposition of either cupric sulfate or cupric oxysulfate. This is very difficult to reconcile with the thermodynamics of the C-S-O System,3 which support the probability that both cuprous oxide and cupric oxide precede cupric oxysulfate and cupric sulfate in the sequence of products formed during the oxidation of cuprous sulfide. In this paper the individual sulfate decomposition reactions will be examined and suggestions will be advanced for the mechanism of reaction. This will be based on the effects on reaction rate of changes in interfacial area, flow rate, and back-pressure of sulfur trioxide. EXPERIMENTAL Materials. The copper source material used in all experiments was Fisher Certified Reagent Grade anhydrous cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared by roasting cupric sulfate for 48 hr, with frequent rabbling, in an open tray in a muffle furnace maintained at 725°C. At this temperature, cupric sulfate develops about 0.16 atm pressure of combined sulfur trioxide, sulfur dioxide, and oxygen. Cupric oxysulfate develops only about 0.05 atm pressure, and is stable until

Jan 1, 1965

By Sidney G. Parker, Jack E. Pinnell

Cubic ZnSe crystals have been grown with HCl, HBr, and I, as chemical transport reagents. The growth of large, well faceted crystals is in the order HCl < HBr < I, with some produced by I, transport being 1 cm on an edge. ZnSe:I crystals showed no strain in cross polarized light and were homogeneous as determined by electron microprobe. These ZnSe:I crystals had a mobility at 25°C of about 300 sq cm per v-sec and contained 103 dislocations per sq cm; further, these crystals were pure cubic and showed both photolumi-nescence and photo conductance. Doping was attempted during crystal growth. ZnS and Zn (S,Se) crystals were also grown by I, transport. ZnSe crystals have been grown by most of the common techniques.1"6 Of these, chemical vapor transport as developed by Kaldis2 showed promise of producing high perfection, cubic ZnSe. With chemical transport, crystals can be grown far below the transition temperature for conversion of cubic to hexagonal structure. A small temperature gradient between source and growth region tends to allow near equilibrium growth, which should lead to good crystalline perfection. Because it is necessary to form volatile compounds, halogens or their compounds are extensively used as transport agents. HCl, HBr, and I, were compared as transport agents for growth of ZnSe crystals. Doping during crystal growth was attempted. ZnS and ZnSxSe1-x crystals were also grown by chemical transport. Electrical and optical properties of the crystals were examined. EXPERIMENTAL Fig. 1 is a sketch of the growth apparatus, which was a modification of Kaldis&apos;. A quartz rod which butted against the seed crystal served as a heat sink to promote growth only on the seed. Initially, crystal growth was attempted with ZnSe prepared by wet chemical methods. Because such a material contained oxides and selenates, HC1 reacted with these oxygen compounds to form H2O and no ZnSe transport occurred. Further, this ZnSe contained about 10 ppm Cu plus other impurities. High purity ZnSe, containing small amounts or no oxygen compounds, was prepared by reaction of H2Se with zinc vapors at 600° to 800°C in an atmosphere of palladium diffused H2.7 The ZnSe thus produced was usually copper free and contained only 1 ppm by weight of magnesium as determined by emission spectrographic analysis. G.E.&apos;s electronic grade ZnS, which had about 10 ppm metallic impurities, was used without further treatment. ZnS-ZnSe charges were prepared by mixing the two compounds together, then sintering 24 hr at 1100°C in an H2S ambient. The gases, HBr and HC1, were commercial grade, of 99.9 pct purity, while the I2 was 99.999 pct pure. The single crystal seeds with (111) faces for growth were mechanically held in place by sealing the outer quartz tube to the growth tube. After the charge was introduced, the system was outgassed at l0-5 torr while heated to 500°C. The desired quantities of transport reagents were then sealed off in the system, which had been cooled to 25°C. The growth tubes were inserted into a furnace with the desired temperature and thermal gradient. The system was allowed to cool for 1 to 12 hr from growth temperatures of about 850" to 25°C. The tubes remained stationary during crystal growth. HCl CHEMICAL TRANSPORT GROWTH Preliminary runs with HC1 had a temperature gradient of 100° to 200°C and no seed or heat sink. Only small crystals were obtained in these experiments as

Jan 1, 1970

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker&apos;s problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker&apos;s problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel&apos;d and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By J. M. Smith, D. Kunii, P. Adivarahan

Effective thermal conductivities were measured for seven samples of porous rocks through which gases or aqueous salt solution were flowing, parallel and countercurrent to the flow of heat. The results are analyzed in terms of the contributions of the solid and fluid phases to the total energy transfer. The solid contribution for the sandstone samples studied was found to be a Junction of the porosity and an effective thermal conductivity for the solid phase. The fluid contribution was a function of the Peclet number. Based upon the equations presented, the effective conductivity of the system can be estimated from the properties of the fluid, the flow conditions, and the porosity and pore-size distribution of the rock. INTRODUCTION Heat-transfer characteristics of porous media containing fluids are needed for the design and evaluation of thermal methods of petroleum production. The study reported here considers the problem of countercurrent flow of fluid and heat in sandstone rocks, and is a continuation of previous studies concerned with parallel and radial flow of energy and fluid in both rocks517 and beds of fine particles.6,10 In addition to these earlier works, Asaad,1 Kimura,4 Preston,8 Zierfuss and vlietll and waddams9 have reported effective conductivities for systems filled with stagnant fluids. There appears to be no published data on rocks through which fluids are flowing. The purpose of this study was to present such information and, particularly, to investigate the effects of properties of the rock and the flow rate on the results. The rock samples were naturally occurring sandstones from different locations and were similar to petroleum-bearing formations. The properties of the seven samples showing the range in porosities and permeabilities are given in Table 1. The mean pore sizes were calculated from mercury penetration data by averaging the radius with respect to pore volume. The details of this method and comparison with other procedures for estimating 7 are given elsewhere. Four fluids, nitrogen, carbon dioxide, helium and 10 weight per cent sodium-chloride solution were used with each sample. For Bartlesville sandstone, BA-5, runs were made at mean pressures from 15 to 250 psig using nitrogen. The other measurements were carried out at a mean pressure of 100 psig. The maximum temperature range eacountered was 70° to 300°F. The flow rate of fluid ranged from about 1.0 to 130 Ib/(hr)(sq ft), and this corresponded to a modified Reynolds-number range of 5 x 10-4 to 1.0. The variation in Prandtl number was 0.70 to 4.1. EXPERIMENTAL WORK The equipment consisted of apparatus to supply a constant flow of gas, or salt solution, at constant pressure to the bottom of a vertical test section, and metering and flow-regulation apparatus after the test section. The flow of salt solution was

By J. D. Pennock

The different samples of brick examined were Grecian magnesite, American magnesite; silica brick and coke-oven tiling made in Belgium and used in retort coke-ovens. The Grecian magnesite was furnished by a New Pork party. The American magnesite and the silica brick were furnished by a manufacturing company in Pittsburgh. From these brick were made cylindrical cores, &apos;79 inches long and 15/8 inches in diameter. At one end of each was drilled a hole about 1/4-inch in diameter and 11/4 inches long, into which the thermometer was inserted during the experiment. Conductivity.—The apparatus used for determining the conductivity, as shown in Fig. 1, is a sheetriron drum, 18 inches in diameter and 8 inches high. In the center is a little combustion-chamber with walls of split fire-brick, 39 inches square and about 6 inches high. The fire-brick, however, pass through the drum to the table on which the drum stands. The cores are placed horizontally, half-way between the top and bottom of drum and on the line of diameters at right angles. In the four walls of the combustion-chamber are cut holes just large enough to allow the cores to pass through. The cores extend

Jan 1, 1897

L. C. Graton, Cambridge, Mass.—The subject of chalcocite occur; rence and its geological significance has, of course, a very important commercial bearing, as shown by the recent remark of a hard-headed mining .man: "This secondary enrichment business is one thing you geologists have put up which we can hang on to, and come out right." Most enrichments of copper ores depend upon the formation Of chalcocite from leaner sulphides. Recently it has been shown that not only does there exist this secondary or derived chalcocite, * but that in certain ores the mineral is present as an initial or original constituent, which therefore we may call primary. The desirability of distinguishing between these two kinds of chalcocite is evident and has recently been emphasized. That constitutes the first problem in this connection. I believe many who are working upon secondary enrichment of mineral deposits are giving much attention to that particular question. It is now possible to distinguish primary from secondary chalcocite in many cases. In such cases, what do we know of the&apos; conditions under which this secondary or derived chalcocite was formed? , This is the second main question in connection with the subject. It is now plain, at least in many instances, that the formation of this derived chalcocite represents a phase of oxidation if we have in mind the primary ore as the thing acted upon. The next important question—and it is most important—is: does such oxidation go on above the zone where the rocks are saturated with water—that is, above the water level—or below, or indiscriminately above and below? Many of you have, or have had, opportunities to study at first hand, day after day, occurrences that&apos; enable valuable conclusions to be drawn upon these and other important questions concerning the formation and significance of chalcocite. It is greatly to be hoped that your testimony will be made available and undoubtedly it will go far toward clearing up some of these doubtful points. John D. Irving, New Haven, Conn.—A short time before this meeting was called, H. V. Winchell, who was unable to be present, requested me to exhibit and describe these two samples of pyrite. (Exhibiting specimens.) They consist of fragments of pyrite inclosed in two small bottles. The first bottle shows fragments of pyrite which were immersed in water carrying copper sulphate but without SO2 for a period of two years. They remained comparatively clear and bright. No chalcocite has been deposited on them. The second bottle shows fragments of

Jan 1, 1915

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company&apos;s Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;&apos; in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany&apos;s own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. &apos;ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4&apos;8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

By C. Richards Honeycutt, Frederick C. Langenberg, Guenter Pestel

Solidification in a moving electromagnetic field was successful in altering the as-cast grain structure of steel ingots. The equipment is described and exerimental results are presented for several different alloys. Conditions for optimum grain refinement are described and an empirical design constant presented. The effect of the grain refinement on hot workability is briefly discussed. T HE grain structure of a steel ingot teemed into a metal mold can be defined by macroscopic examination in semiquantitative terms. For example, the relative volume of obviously differing structures can be estimated with the classic definitions of chill, columnar, and equiaxed zones. Experimental evidence has proven that the grain structure of an ingot is affected by changes in such factors as teeming temperature, rate of teeming, degree of turbulence, size of ingot, mold characteristics (including preheat temperature, design and coating), and composition of the metal (especially as it affects the range of solidification). Significant advances have been made in fundamental solidification studies; but the principles which have been developed are difficult to apply tothe complex and changing phenomena that occur simultaneously during ingot solidification. In particular, many attempts have been made to refine the as-cast structure of ingots, with special emphasis on the columnar grains. The formation of large columnar grains is generally considered harmful to the further fabrication of an ingot. It may also result in undesired ani-sotropic properties. However, columnar grains are not undesirable in all grades, or product applications, and caution must be exercised to determine in which grades and applications columnar grains are not desired in the ingot. Although the literature on the refinement of as-cast ingot grain structures is too vast in general to review here, it is noteworthy that such methods are additions of artificial nuclei, mold vibration, mechanical stirring or ultrasonic agitation of the molten metal, and controlled cooling and reheating during solidification have been tried with varying degrees of success. However, it is doubtful that any method of refining the as-cast ingot grain structure has been completely successful on a commercial basis. The purpose of

Jan 1, 1962

By James Boyd

THE Bureau of Mines for a number of years has been seeking additional ways and means of improving the efficiency of its operations and increasing its service to the public. It has become obvious that changes in the organization of the Bureau are essential to a more effective accomplishment of its functions and objectives. The old organization was defective in meeting current needs in that the Bureau&apos;s field activities were neither sufficiently coordinated with the national program nor were they particularly responsive to local needs of the mineral industries. Further, the traditional organization hampered the efforts of the Bureau to obtain, analyze and provide to the policy-making agencies of the Government essential information and advice in such a form that the requirements of domestic industry could be fully taken into consideration in the development of domestic and foreign policies. Consequently, the Bureau has now modified its organizational structure.

Jan 1, 1949

Primarily, 1961 was a year for widespread application of tools and techniques which have become operational in the past several years • • • Raising --Raise climbers and climber raising techniques have been improved; narrow veins as low as 55° dip are now being mined from climber raises. Climber modifications include: larger motors, tighter radius curves negotiated, improved lubrication and new methods of stowing the climber during a blast. Climber raises are now ventilated in several ways: a 12-in. diam flexible vent tube behind the climber rail; a 6-in. diam pipe behind the climber rail (with fan); or a 6 to 8-in. diam drill hole along the axis of the raise. In hot raises, these ventilating techniques have resulted in more rounds per shift. When driving raises from crosscut and lateral development, mucking machine loading of raise rock is preferred over slusher ramp loading for the following reasons: a) faster set-up and teardown of climber facilities; b) easier access for climber maintenance, repair and loading of raising supplies; c) area at the bottom of the raise can be kept cleaner. Both wide and narrow veins are mined from 7 x 7-ft climber raises at Butte and at Republic, Wash. At Republic, climber rollers have been modified to support increased weight when driving 55°dip raises • Drilling-The new largebore, short-stroke push feed drills are much faster drilling than previous models and are most satisfactory in hard ground. Although reports on maintenance studies of the new drills are not yet available, increased steel and bit wear and breakage, and increased drill maintenance are seen as potential problems. Mines in Montana and Idaho continue to test rubber-collared drill steel. The fabricating methods used are successful but advantages in increased steel life have yet to be proved. Underground applications of down-the-hole drills continue. Drilling speed and accuracy are reported as the outstanding advantages. Manufacturers are now hopeful of making drills which will operate in any direction. Present applications are for ventilation holes (to 8 in. diam) for climber raises, holes for hydraulic fill distribution, drain holes and "predrilled" raises. Good drilling accuracy has been reported to a depth of 200 ft. Cutting holes in drifting is seen as a future application

Jan 2, 1962

By C. A. Meissner

The; following is a further discussion of the paper of James Qayley, " The Application of Dry-Air Blast to the Manufacture of Iron " (Trans., xxxv., 746), with special reference to his supplementary paper (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 797 to 819), and to the paper of J. E. Johnson, Jr., " Notes on the Physical Action of the Blast Furnace " (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1111 to 1146). Mr. Gayley&apos;s paper has been discussed also by E. Windsor Richards, R. w. Raymond, E. H. Saniter, W. J. Poster, H. M. Howe, V, Pendred, B. H. Thwaite, James Gayley and Alexander Pourcel (Trans., xxxv., pp. 1022 to 1042), Joseph W. Richards (Bi-Monthly Bulletin, No. 4, July, 1905, pp. &apos;703 to 718); T. W. Robinson (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 788 to 796); C. B. Dudley, R. W. Raymond, J. E. Johnson, Jr., W. F. Mattes, James Gayley, David Baker, John Birkin-bine and F. E. Bachman (Bi-Monthly Bulletin, No. 5, Septem-

Jan 1, 1907

F. N. SPELLER (communication to the Secretary*).-It would certainly be interesting to know more about the heat balance in this practice, but there seems to be no doubt that the net result is a greater absorption of heat where roll scale is used instead of solid metal scrap. In the experimental heats referred to, about an equal weight of pig iron or steel scrap was replaced by roll scale. This caused a reduction of about one-third in the time of blow compared with a heat of the same

Jan 6, 1917

By E. C. Rien

When the electrical system for a surface or open pit mine is designed, four major considerations should be satisfied in the following order: safety, reliability, flexibility, and cost. Careful planning initially will make expansion for future growth economical as well as possible without extended shutdown of operations. Electrical requirements in surface and open pit mining can be divided into three categories: main substation, plant power, and pit distribution. These systems are integral to each other, but will be dealt with separately here. 11.2-1. Main Substation. A main substation for a mining operation may vary from a 500 kva transformer supplying 480-v power to motor-driven pumps and conveyors, to a 50,000 kva substation serving a large beneficiation plant or a large strip mining operation. Regardless of size, it should be designed with the realization that a failure of the main substation will totally shut down the operation (Fig. 11.2-1.). Location of a main substation usually is a compromise between expense of running the incoming high-voltage transmission lines and the voltage drop of long secondary runs. Based on a geological survey for immediate and future areas of excavation, the main substation should be located as near to the center of load as possible. The site should be out of the blasting area, readily accessible to authorized personnel, and situated where prevailing winds will keep it free from dust or snow. DISCONNECTS AND OVERLOAD PROTECTION. The main substation should have a primary disconnecting device-either a pole top gang-operated switch and fuses of adequate interrupting capacity or, preferably, an oil circuit breaker with properly coordinated relay protection.

Jan 1, 1968

By Cleland N. Conwell

Coals are found in all parts of Alaska, ranging in geologic age from Carboniferous to Tertiary, and grading from lignite through anthracite. Only the Matanuska and Nenana coal fields have been extensively developed. Nenana Field Today roughly 94% of the coal mined in Alaska comes from the Nenana field near Healy. The coal-bearing horizons in the Nenana field are found in a sedimentary sequence of Tertiary age approximately 2800 ft in thickness. The sediments rest directly on schists of possible Precambrian age. Individual coal beds in the field have been designated by both letters and numbers, starting with the alphabetical designations from A to G, and the numbers 1 to 6. Of these coals, the principal beds that are mined are F, 1, 2, and 3. These vary greatly in thickness, e.g., bed 1 ranges to over 50 ft, and beds 2 and 3 to 30-40 ft.

Jan 10, 1972

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson&apos; have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,&apos; have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892