Search Documents

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By Norman D. Fitz, Gerald

BOTH physical and economic factors are concerned in determining the optimum rate of depletion of a mineral deposit. The physical limitations are, in a large measure fixed by nature. Economic influences on the other hand, are man-made and subject to wide changes. Analyses of the interrelations of these two groups of factors are of major importance in selecting the optimum rate of production of petroleum and mining properties and in their valuation. Physical Influences PRIMARY limitations on the rate of mining are the rate of shaft sinking and underground development, the rate of hoisting, and the rate of sloping. These rates are largely determined by the physical features of a property. Technical methods which may be employed, and consequently the length of time required, are governed by the dimensions of the deposit, its attitude, depth, regularity, the unit value and character of the ore, the nature of the wall rocks, and similar factors.

Jan 1, 1938

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By R. L. Rickett, W. C. Leslie, W. D. Lafferty

Notch toughness of 0.10'pct C steels, rimmed or killed, is improved by holding the steel at a temperature just above the Ae,, followed by air cooling. The improvement can be gained without apparent change in gross microstructure or hardness. The limits of the process have been determined and some possible reasons for the observed effects are discussed. The results appear to indicate that the current theories of transition temperature are inadequate. THE effects of gross microstructural variables (ferrite grain size, austenite grain size, type and distribution of carbides) on the notch toughness of mild steels have been the subject of many investigations.'-' The results indicate that increasing ferrite grain size raises the notch-impact transition temperature. The transition temperature also rises with increasing size of pearlite colonies and with increasing prior austenite grain size, but these factors are not independent of ferrite grain size. The effects of gross composition of steels have also received considerable attention. As a result, manganese, nickel, aluminum, and silicon are known to improve the notch toughness of mild steels. The other elements that have been investigated—carbon, nitrogen, boron, copper, chromium, molybdenum, phosphorus, sulfur, titanium, and vanadium—reportedly are either deleterious or have little effect on notch toughness. Despite this large volume of work, it is still not possible to predict the notch toughness of a mild steel from its microstructure and composition, even when these are supplemented by hardness and tensile tests. Steels with equivalent microstructures, but different thermal and/or mechanical histories, can differ in notch toughness. Such factors as type and distribution of precipitates, substructure, local variations in composition, or unrecognized variables, may be important in determining the notch toughness of mild steels. However, quantitative knowledge of the effects produced by these factors is almost completely lacking. In an effort to improve this situation, an investigation was begun to determine the effect of a very fine precipitate on the notch toughness of low-carbon steels. Aluminum nitride was chosen as the precipitate because of its presence in aluminum-killed steels, the ease of control of precipitation, and past

Jan 1, 1961

By E. D. Gardner

FIFTY years ago the Utah Copper enterprise at Bingham was just getting under way. An epic in metal mining was in the making. Throughout the West the bonanza deposits were approaching exhaustion and most ore still went direct to smelter. But concentrators were shortly to be constructed for treating milling grade ores, and most important, the pilot plant for the Utah Copper enterprise was being built that year at the mouth of Bingham Canyon. The same decade was to see development at the Inspiration mine in Arizona of the most important new mining method for 50 years to come—undercut block caving. Although the average grade of ore being mined has been declining for 50 years, and wage rates and prices of supplies have been greatly increased, the mining industry has continued to grow and to prosper. Technology has advanced to a point where minerals can be mined under the most severe conditions. The hardest rock can be drilled and broken and the heaviest ground handled. Large or small, an ore-body can be mined successfully, at any desired rate of production. It is possible to pump great volumes of water and to ventilate the most extensive workings; air conditioning has made practicable the mining of ore where the rock temperatures are beyond those that can be borne by man. Mining today in the U. S. is a huge earth-moving operation. In 1953 nearly 2 billion tons of material were mined for direct use or for processing. Stripping at open-cut mines totaled about 1.7 billion cu yd. Table I gives relative tonnages of the branches of the mineral industry in 1953. In addition to the solid materials moved, 350 million tons of petroleum and 340,000 tons of gas were produced in 1953. Fifteen million tons of salt and 5 million tons of liquid sulphur were pumped from wells. An appreciable amount of copper was recovered by leaching old mine workings and dumps. Total value of minerals produced in 1953 was $14.4 billion: oil and gas $7.6 billion, coal $2.6 billion, nonmetallics $2.4 billion, and metals $1.8 billion. Formidable problems face some branches of the industry today, especially pertaining to increased output tons per manshift. The time has come when these problems should be reappraised. With current wage rates, the industry no longer can afford to pay men to do manual labor. It should be recognized, also, that the miner is a skilled worker; efforts to promote the dignity of his calling and his pride of accomplishment have yielded beneficial results. Mineral deposits occur under widely varying conditions. In most instances the degree of support needed by the roof and walls is the deciding factor in selection of an underground mining method. The degree of support needed, in turn, is governed by natural physical characteristics of the ore and its enclosing rocks. Mine operators, of course, learn to judge ground by observation, and an experienced mine boss generally can anticipate what will happen following any given mining operation. A more scientific approach, however, would be advantageous in most cases. More should be known about the strength of the ore and the enclosing rocks, more about stresses set up in the ground when ore is removed, and more about the mechanics of moving ground. Better understanding would work both ways: first, favorable rock conditions could be fully utilized for more efficient mining, and second, hazards of rock falls could be minimized, loss of ore in mining reduced, and expenses caused by ground pressures and subsidence lowered. In general, mining comprises breaking the ore or rock in place, supporting the mine workings, and transporting the ore to the surface. This latter is a materials handling problem. Ventilation, of course, must be provided, and the mines must be kept free of water. Development work at some places is the most important cost item in extracting ore. Drilling and blasting remain the usual practice for breaking ore or rock from place except, of course, at block-caving mines. The drilling and blasting practice at a mine must fit the mining method. In laying out mining procedures attention is being given to

Jan 1, 1956

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

The following list comprises the names of those persons who became members during the period May 10, 1916, to June 10, 1916: ARCHIBALD, JOHN CHRISTIE, Min. Engr., Supt. of Cyanide Plant, Guanajuato Reduction Mines, Guanajuato, Mex. BRUNEL, FRANK P., Cons. Min. Engr Mitchell & Brunel, Ajo, Ariz. CALVERT, WILLIAM ROBERT, Cons. Geol. ...225 Kearns Bldg., Salt Lake City, Utah. CHAMPION, J. R., Supt The Yak Mining, Milling & Tunnel Co., Leadville, Colo. CHARLES, LAVERN JOHN, Construction Engr., Elephant Butte Dam, Elephant Butte, N. M. CHASTEL, ANDRE, Min. Engr., Societe Miniere & Metallurgique de Penarroya, 12, Place Vendome, Paris, France. CHRISTIE, WALLACE H., Vice-Pres. and Mgr., Alt. Bert Gold Dredging Co., 604 Mission St., San Francisco, Cal. CLARK, RONALD ..Hardinge Conical Mill Co., 120 Broadway, New York, N. Y.

Jan 7, 1916

By T. T. Field, M. Gell

MUCH has been learned about plastic deformation behavior in crystals through the use of dislocation and slip band etchants. Slip in nickel and nickel-base alloys has previously been revealed by various etching techniques.l-5 The techniques for nickel-base super-alloys4,5 were successful only in the Udimet 700 composition in specific heat-treated conditions. The objective of this work was to develop a more generally applicable slip-band etching procedure. The nominal compositions of the alloys used in this study are listed in Table I. The low carbon Mar-M2OO alloy referred to in the text is the same as listed in Table I with the exception that the carbon content is less than 100 ppm. Mar-M200 and Udimet 700 were solutionized at 2250" and 2150°F, respectively. The aging treatment for both cast alloys was 32 hr at 1600°F and for wrought Udimet 700 was 4 hr at 1975"F, 24 hr at 1550°F, and 16 hr at 1400°F. The new slip-band etching technique consists of a chemical etch followed by a short electropolish, Table 11. Fig. l(a) shows the best result obtained on an internal section of a plastically deformed single crystal of Mar-M2OO when using a conventional slip-band etching procedure which consists of electropolishing followed by etching. Ghostlike traces corresponding to planar slip bands are observed, but the contrast between the bands and the background is weak. Fig. l(b) shows the same field using the new slip-band etching technique. After the etching step of this technique, the same ghostlike traces of Fig. l(a) are observed, but the subsequent electropolishing accentuates the slip bands and the subgrain boundaries while the rest of the matrix is being polished. Longer electropolishing obliterates the slip bands. The new slip-band etching technique makes use of the etchants and electrolytes that are normally used for a given material. Because of this, it should be possible to slip-band etch other nickel-base superal-loys by using existing etchants and electrolytes for a material and following the procedures outlined in the "Comments" section of Table 11. All the illustrative examples given below show internal plastic deformation in single crystals of regular and low carbon Mar-M200 in the solutionized and

Jan 1, 1970

By A. E. Back, S. F. Ravitz

When manganese ores are leached with sulphur dioxide, a large part of any zinc in the ore usually is extracted with the manganese.1 In the dithionate process,2,3 in which the manganese ore is leached with dilute sulphur dioxide gas and the manganese is subsequently precipitated by adding lime to the pregnant solution, the zinc is precipitated with the manganese. These facts suggested the possibility of applying the dithionate process to the recovery of zinc from oxidized ores or calcined sulphide concentrates. Accordingly, an investigation was begun, and preliminary tests were made on several ores and concentrates. The results were encouraging, but the need to devote available funds and personnel to other projects made it necessary to drop the work before the various factors involved in the process could be studied in detail. A brief mention of the process,4 however, elicited a number of inquiries, so that it appeared desirable to report the results of the preliminary work. The dithionate process as applied to zinc may be summarized briefly as follows: The ore or calcined concentrate is leached with dilute SO2 gas to dissolve the zinc, largely as zinc sulphate, in accordance with the following equation in which [ZnO] represents the "oxide zinc" in the ore or calcine: [ZnO] + SO2(g) + 1/2 O2 = Zn++SO4— [1] If, in the leaching step, the ore or calcine is suspended in calcium dithionate solution, the sulphate ion, as it is formed, is precipitated immediately as calcium sulphate, which is subsequently filtered off with the insoluble ore residue: Zn++SO4— + Ca++S2O6— = CaSO4(s) + Zn++S2O6- [2] An alternative procedure is to suspend the ore in water, filter off the insoluble ore residue after leaching, add calcium dithionate to the resulting zinc sulphate solution, and then filter off the calcium sulphate precipitate. In either event the zinc is obtained in the form of a pregnant solution of zinc dithionate, from which it can be precipitated as relatively pure zinc hydroxide by adding milk of lime: Zn++S2O6— + Ca(OH), = Zn(OH)2(s) + Ca++S2O6- [3] The zinc hydroxide precipitate is calcined to form the final zinc oxide product: Zn(OH)2 = ZnO(s) + H2O(g) [4] Theoretically the process is completely cyclic with respect to dithionate ion, the calcium dithionate required for reaction 2 being replaced by that formed in reaction 3. In practice, of course, small amounts of dithionate would be lost in the various filter cakes, depending on the economic washing limits. In the leaching step, however, some of the SO2 is oxidized to dithionale instead of sulphate, accord- ing to the following overall reaction: ZnO + 2SO2(g) + 1/2 O2(g) = Zn++S2O6-, [5] so that the dithionate losses are made up, at least in part. Ores and Concentrates Tested The analyses of the ores and concentrates tested are summarized in Table 1, which also includes the analyses of the calcines produced from the concentrates. The concentrates were roasted in a laboratory muffle furnace at the temperatures indicated until evolution of SO2 could no longer be detected; shallow clay dishes ordinarily were used; but calcines 2a and 2c were prepared in iron dishes, with the result that these two calcines were badly contaminated with iron scale. The "complex" concentrate, sample 1, consisted essentially of sphalerite grains containing inclusions of pyrite and other sulphide minerals too minute to be liberated by grinding within economic limits. In the " marmatitic" concentrate, sample 2, the iron was present largely as marmatite (that is, as iron sulphide in solid solution in zinc sulphide) rather than as pyrite inclusions. The zinc was present largely as the carbonate in the two "oxidized" ores, samples 3 and 4, and as the silicate in the "willemite" ore, sample 5. Leaching Tests The leaching cell was a 3-liter glass beaker placed in an electrically heated water bath manually controlled to maintain a temperature of 35°C in the leach slurry. The slurry was agitated by means of a flat paddle-type stirrer

Jan 1, 1950

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

The war story of the engineer corps at home and in France is told officially for the first time in the advance sheets of the War Department's brief history of American war efforts. Many of these accomplishments have been published before as isolated incidents, but they gave no idea of the extraordinary duties modern warfare has laid upon engineering troops. In the engineering units that reached the other side, there were seven regiments and two battalions of railway construction engineers; five battalions for maintenance of way; two battalions for maintenance of railway equipment; four regiments and one battalion to operate the main American railways in France; three regiments to operate light railways and their repair shops; two regiments to operate the regular railway repair shops; two regiments and six separate battalions on general construction work; two regiments for storing and transporting engineer supplies; a forestry regiment; a light-railway construction regiment; a roadbuilding regiment; a water-supply regiment; a mining regiment; a quarrying regiment; a technical regiment for surveying and sound ranging; three survey and printing battalions; two railway transportation battalions; an electrical and mechanical regiment; several separate companies to operate cranes; a camouflage service; five inland waterway companies, to operate canal boats and the like; five pontoon trains and a pontoon

Jan 6, 1919

By S. W. Miller

MOST of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,1 that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., when he has found them in large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than ;3/4 in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top ;1/16 in. (1.5 mm.) of the weld, they were removed by the grinding or machining; also, welds ¾ in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign -of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was

Jan 2, 1919

By R. J. Colony

THE failure, or disintegration, of concrete in structures, even when the cement, sand, and coarse aggregate used have passed satisfactorily all tests and inspections, is not uncommon. Such failures occur even when proper methods of mixing and placing have been used and where, weather conditions were correct. In these cases, the origin of the trouble must be sought in the cement, therefore some additional mode of determining the quality of cement must be employed. The problem is to find a simple, usable; easily applied method that will supplement the standard tests. The solution of this problem in-volves a knowledge of the chemical composition of Portland cements, also of their constitution (or componental composition), as the behavior of a cement, when gaged, is dependent on the physical and chemical characters of the compounds of which it is composed, the proportions existing between them, and the fineness of grinding. It is likewise essential to know the character, behavior, and composition of the hydration, products of Portland cement. The most promising method of attack makes use of chemical, mechanical, and petrographic methods. Chemical, by determining quantitatively not only the usual constituents, but the carbon dioxide and water. Mechanical, by determining the fineness with the air analyzer,1 which separates into fractions of various grain dimensions all of that portion, which in the ordinary sieve test passes the 200-mesh sieve and constitutes at least 75 per cent. of the total cement. These fractions may be further studied chemically and petrographically and micrometric measurements made of the grains. Petrographic, by the method of immersion, and by making thin sections from test pats of both neat cements and standard` mortars.

Jan 1, 1921

By Daniel T. O’Brian

Mineral exploration activities are benefiting from new interpretive techniques which have become economically practical with computers. Government agencies, educational institutions, and industry have each contributed research and development efforts for improving the mathematical analysis and graphical display of exploration data, resulting in operational aids not foreseeable a decade ago. Progress has been worldwide and is expanding rapidly. Books 1-10 are supplementing the periodic literature, at least one abstracting service is now active, 11 and an association has recently been formed to encourage and publicize advances in this field. 12 With the diversity of applications, only partial coverage of the subject can be made at any single symposium. Four of the six papers in this section report on the current state-of-the-art in selected areas of interest: graphics, time-sharing, mathematics, and economic analysis. The remaining two papers are descriptions of advanced statistical techniques for gaining additional information during exploration, and illustrate methods which will become more commonly applied in the future. "Computer Graphics: A New Tool for Exploration and Mining" describes the use of a computer and accessory equipment as an information retrieval device, graphically merging and displaying pertinent information for visual inspection and interpretation. This is a rapid means of studying information which has been pre-stored in a form accessible to the computer. Time-sharing is a means of achieving a comparable rapid response when calculations are being performed. The paper, "Some Applications of Time-Sharing in Mining Geophysics," describes the experience of one company using a time-sharing facility for geophysical computations. Another paper on this subject, stressing mining applications, has recently been published. 13

Jan 1, 1969

By D. L. Harris, A. M. Gaudin

Observations were made of the distribution of mercaptan containing S35 between aqueous solution and mineral and between aqueous solution and the gaseous phase. Although equilibrium may not have been attained, adsorption of the reagent was shown to occur reasily from air or aqueous solution on sphalerite, zincite, and willem-ite and to correspond to flotation. Adsorption on quartz did not similarly occur. THE following results, presented here in condensed form,' were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report' of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr. Coarsely-crystallized sphalerite was handpicked, stage-crushed in the dry state, wet-screened on a 200-mesh sieve, and deslimed in water at about 5 microns. Further treatment consisted of a wash in dilute aqueous hydrogen peroxide, drying, removal of the dark-colored fraction in a Frantz magnetic separator, washing in very dilute hydrochloric acid, repeated washing in distilled and conductivity water, and drying. The last washings showed a conductivity equivalent to a few ppm NaC1, that is, much more than would be provided, theoretically, by a saturated ZnS solution. The material was stored dry in sealed bottles. Analyses were as follows: Zn, 62.3 pct; Fe, 0.43 pct; Cd, 0.44 pct; S, 31.2 pct; Mn, 0.001 pct. The specific surface (BET method) was 2000 cm2/g. Zincite from Franklin furnace of the New Jersey Zinc Co. was hand-picked, dry-crushed, wet-screened at 100 mesh, and deslimed at about 10 microns. After drying, the associated zinc, manganese, calcium, and silicate minerals were removed in a Frantz magnetic separator. The purified zincite was washed in distilled water and conductivity water to a conductance of less than 2 ppm equivalent NaC1, dried, and stored. Analyses were as follows: Zn, 75.1 pct; Fe, 0.9 pct; Mn, 2.78 pct. The specific surface (BET method) was 1740 cm 2/g. Willemite, also from Franklin furnace, was purified similarly. Analyses were as follows: Zn, 52.5 pct; Fe, 0.12 pct; SiO², 27.3 pct; loss on ignition, 0.13 pct. The specific surface was 1760 cm 2/g. Conductivity water (double-distilled) and demin-eralized-distilled water were used in most of the tests. The specific resistance was not less than 600, 000 ohms, and usually above 1,000,000. Radiosulphur-marked hexyl mercaptan (1-hexane thiol) was synthesized by Tracerlab, Inc., Boston. Two lots were secured several months apart. The last lot, consisting of about 0.5 g of the mercaptan, had a total activity of about 10 millicuries. Tracerlab Co. guaranteed only the activity; hence a quasi -vapor pressure determination (based upon an S analysis) of the mercaptan was made. The calculated value, 4.2 mm of mercury at 25.5' C, has been compared with that of a sample of Highest Purity 1-hexane thiol from Fisher Scientific Co. The latter had a vapor pressure of 4.5 mm of mercury at 2.5 C. Analytical Procedures The sample containing radiosulphur-marked mercaptan was oxidized to convert the mercaptan sulphur to sulphate, carrier barium sulphate being added to provide a suitable quantity of total barium sulphate in a filter cake. The precipitate was filtered and dried, and counting was carried out either in a streaming-gas (Q-gas) counter for high sensitivity or with an end-window G-M counter for convenience. The oxidized and precipitated mercaptan gave a radioactive count of 65 counts per minute per microgram in the end-window Geiger-Mueller counter and 1100 counts per minute per microgram in a Q-gas counter. For standardization of the mercaptan solution, 15 replicate analyses were made. The average deviation per measurement was about 1600 cpm in 65,000 cpm, the probable error in the mean being 275 cpm. It

Jan 1, 1955

By Mourad Aissa

From our previous work (Gardner, Aissa, and Verghese, 1982) on determining the residence time distribution of ball mi 11s from radiotracer data taken in closed-circuit operation without interruption of the process, it occurred to us that the data taken for this purpose also contained information on the breakage rates of all the sizes present. It is the purpose of the present work to evaluate methods to obtain breakage rates from this data. A numerical solution for the impulse injection and subsequent detection of radiotracer in a closed-circuit linear comminution process is developed and used with typical breakage parameters, residence time distribution, and classifier functions to study and evaluate these methods.

Jan 1, 1984

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946