Search Documents

By H. E. Doerr

THE writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to he that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities: Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and air-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250° F. (1235° C). Approximately 1 min. was required to forge under the steam hammier to 1 ¼ in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders ½ in. (17.7 mm.) in diameter and ½ in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. No in-formation was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by

Jan 1, 1919

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By G. Thodos, D. E. Matschke

Cansiderable time and effort frequently are expended to establish, with a degree of confidence, the PVT behavior of pure substances. In particular, a great deal of experimental information contributed by a number of investigators is available in the literature. The data of each investigator, although significant in themselves, cannot be used with a high degree of confidence until they are compared with the continuum of information presented by others. Current interest in thermodynamic and transport properties, for not only the gaseous state but the con-densed state as well, requires that PVT infarmation be presented for both regions. The density dependence on temperature and pressure, when presented as a continuum, is of considerable value in itself, especially since the available equations of state fail to properly account for the PVT behavior in the condensed state. For this reason and to incorporate PVT data recently presented in the literature, this investigation was carried out. In their studies concerned with the thermodynamic properties of methane, Matthews and Hurd in 1946 utilized the data of Kvalnes and Gaddy and Olds, Reamer, Sage and Lacey to establish the PVT behavim of methane in the superheated region and the saturated liquid densities of Keyes, Taylor and Smithl in conjunction with the Clapeyron equation to develop the densities for the saturated envelope. Current activity sponsored by API Project No. 44 under the direction of F. D. Rossini has led to a tabular presentation of compressibility factors for gaseous methane in the superheated region.la These values were obtained by using smoothed residuals, developed from experimental data and the Ben edict-Webb-Rubin equation,' to establish internally consistent compressibility factors for the real gas. This approach offers probably the most precise presentation of PVT information for gaseous methane to date. The PVT behavior of methane also can be represented accurately by equations of state such as the Benedict-Webb-Rubin equation or the Martin-Hoa equation.' These equations, although valuable for analytically representing the PVT behavior, lack precision in the compressed-liquid region. The PVT data available in the literature for methane were utilized to obtain reduced densities that are presented in Figs. 1 and 2 as functions of reduced temperature with parameters of reduced pressure. The critical constants utilized for methane are those reported by Kobe and Lynn." These critical values, T, = 191.1°K, PC = 45.8 atm and p, = 0.162 gm/cc, produce a critical compressibility factor, z, = 0.289. The PVT information, as obtained from the literature, in many instances was not presented in an immediately

By F. Keller, E. H. Dix, R. W. Graham

Aluminum alloys containing relatively small amounts of magnesium and silicon are of commercial interest because they are readily workable in the annealed form and may be hardened and strengthened by suitable heat treatment. An intermediate temper can be produced in these alloys by quenching after a Solution heat treatment and the alloy in this condition can be formed easily. Artificial aging is required to obtain the maximum mechanical properties but this aging does not cause distortion nor require elaborate heat-treating equipment. The hardening of the alloys after quenching is attributable in part to the retention of the compound Mg²Si in solid solution, while the maximum hardness obtained by subsequent artificial aging is attributed to the fact that the solid solubility of the compound Mg²Si in aluminum decreases with decreasing temperature. Considering the importance of aluminum alloys susceptible to heat treatment, it is surprising how few fundamental investigations have been carried out on the aluminum-magnesium silicide alloys. This paper deals principally with the solid solubility relations of the compound Mg2Si in aluminum and is the sixth paper of a series1 from the laboratories of the Aluminum Co. of America reporting the results of investigations of equilibrium relations in aluminum-base alloys made from high-purity aluminum."

Jan 1, 1931

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985

Spencer Gulf takes off from the Great Australian Bight cutting a 200 mile deep wedge of water into the South Australia coastline. A pale winter sun shines yellowly on the choppy surface of this body of water which is progressively more salty as it approaches Port Augusta at the head of the Gulf. Once Port Augusta thrived as a grain port and the speedy clipper ships began or ended their legendary races there. On the eastern shores of Spencer Gulf, farm land spreads away from the water's edge. The western side of the gulf meets marginal grazing land of acacia tree and salt bush. Part way down the gulf, there are two industrial towns facing each other from opposite shores; Port Pirie on the east and Whyalla on the west. These towns are like half brothers, the common parent being the founders of Broken Hill Pty. Ltd., (BHP) who began lead smelting at Port Pirie and discovered iron ore near Whyalla needed for the lead smelting process. The iron deposits later became the inspiration for BHP's iron and steel business.

Jan 10, 1964

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985

By Walter Harvey Weed

The enrichment of mineral-veins as a result of the migration of material from an upper oxidized or disintegrated part of a vein to a lower level, where it is redeposited, is now, I believe, quite generally accepted as one explanation of the occurrence of bonanzas in gold- and silver-veins, as well as that of bodies of high-grade ores in cupriferous deposits.* Vogt has called attention† to the fact that there are numerous examples of such rich shoots which are " of exclusively primary character, and dependent upon the laws which governed the original ore-deposition." To this I would add that there are also other examples which are neither of primary origin nor due to descending waters, but. result from a reopening of the veins and their penetration by ascending heated waters whose metallic contents are deposited by reaction with the primary pyrite (and possibly other minerals), forming "secondary" enrichments. My studies of the copper-veins of Butte, Montana, show: That the veins there are of several ages and systems; that the older primary quartz-pyrite veins were reopened by later movements, correlated with a period of volcanic activity; and that they were penetrated by hot alkaline waters carrying copper and arsenic in solution, which was deposited presumably by reaction with the pyrite of the original vein. The enormous development of the Butte deposits, attendant upon the extraction of nearly 10,000 tons of ore a day, has revealed many facts concerning the nature and distribution of the ores. Enargite, the copper sulpharsenate, formerly a relatively rare mineral, is now found to be the chief ore of some veins,

Jan 1, 1903

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas' have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

By E. H. Herron, J. H. Perry

Mathematical simulation of reservoir behavior may be used to help understand reservoir processes and to predict reservoir behavior, thereby leading to the most economically desirable form of exploitation. In addition, simulation can be used as a tool for reservoir description to learn more about the physical nature of the reservoir and the mode of primary recovery. This use is essential in most reservoir studies and represents one of the more significant applications of simulation. Prediction of reservoir behavior provides information concerning displacement efficiency, optimum well locations, and the comparison of alternative producing processes. Since oil, water and gas all commonly occur in many reservoirs, a simulation that takes into account the simultaneous flow of three immiscible phases is a prerequisite for obtaining such information. Furthermore, a simulation that describes this flow in two dimensions provides the capability of evaluating combination gas- and water-drive reservoirs with either an areal or a cross-sectional description. Many reservoir problems require such a simulation. The objective of the research described here was to develop a mathematical model and associated computer program for accurate, efficient, and economical prediction of the reservoir flow of three phases in two-dimensional geometry. Several authors have discussed multidimensional reservoir simulation of two phases.l-3 Gottfried et al.' presented an analy- sis of three-phase simulation in one dimension. Fagin and Stewart" and Garrett6 have discussed the simulation of three-phase flow in two dimensions, but their solution techniques were different from the method discussed in this paper. In particular, previous models and computer programs have usually involved either fewer capabilities or inefficient and less rigorous descriptions resulting in limited applicability. In the following sections, we present a description of the model, an evaluation of the method, and the application to reservoir problems. Additional and supporting material is presented in the Appendix. The Three-Phase Model General Description The three-phase model consists of the mathematical description of the flow of oil, water and gas in a reservoir. Conceptually this description considers flow in all three space dimensions, but in the subject simulator it is assumed that no flow occurs in the third dimension. The model includes the effects on reservoir behavior of fluid and rock compressibility, viscosity, gravity, capillary pressure, relative permeability and gas solubility. Within the two-dimensional restriction, the reservoir considered may be completely heterogeneous and anisotropic. The differential equations governing multiphase, multidimensional flow in a reservoir are too complex to be solved analytically, so they are approximated by a system of finite difference equations and solved

Jan 1, 1970

MEMBERS-QUALIFICATIONS AND ELECTION SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall he entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which be must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which be may belong.

Jan 1, 1938

By Harold V. Pearce

THE plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters' described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions have led to a modification of the former smelting practice, and this modification forms the basis of the present paper. No claim is made for personal originality in connection with these improvements, in fact, I expressly disclaim any such intention, since nearly every successful step in the development of the process now used at Argo has been suggested by Dr. Richard Pearce at various times during the past 12 years, though perhaps in a different manner of exe¬cution. These changes would undoubtedly have been made before, were it not that many problems of greater metallurgical importance and momentarily of more urgent need thus had to be solved. At the time to which I refer, economic conditions demanded mainly an increase of capacity. Moreover, the determination and placing of exact losses in smelting were not so imperative as they now are. About three years ago, the time of my appointment to the - management of. the works of the Boston and Colorado Smelting Co., the great decline in the price of copper occurred; the Argo plant, in common with all others engaged in the copper-industry, lost heavily in the market-value of the stocks on hand of ore and furnace-products. Added to this was the unfortunate circumstance that the copper-supply of the Argo plant from general sources began to dwindle; in fact, it almost entirely ceased. About this time the smelting-plants in the west-

Mar 1, 1905

By J. HUNER

Twenty-four new fields were found in Louisiana during 1945. Of this number 15 were oil fields, eight were gas condensate, and one a dry gas field. None of these fields, with the exception of West Delhi, is as yet of any great consequence. The Weeks Island field in Iberia Parish may eventually develop into a considerable reserve.

Jan 1, 1946

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By J. H. Rose

The arrangement of the reverberatory furnace and the two waste-heat boilers at the Magma Copper Company's smelter at Superior, Ariz., is shown in Fig. 1. The inside dimensions of the furnace at the slag line are: length, 96 ft.; width, 22 ft. The boilers are Erie City vertical type with a rated capacity of 700 hp. The 3-in. boiler tubes are arranged in two banks with a vertical baffle between. The banks are 30 tubes wide by 9 tubes deep—a total of 540 tubes.

Jan 1, 1934

By L. G. Huntley

A description f the geology and conditions affecting the occurrence and mining of oil; also the prospects of obtaining oil in different parts of the country. THE Colombian highlands consist of three parallel mountain ranges (Fig. 1) called respectively the eastern, central, and western cordillera of the Andes. A segment of the range that forms the backbone of the Isthmus of Panama also extends into Colombia, along the Pacific coast, as far southward as the mouth of the San Juan River. These four mountain ranges furnish the key to the varying climatic conditions and vegetation of the country. The river valleys are hot and covered with dense tropical growth. This is also generally true of the coastal plain, although in the northern portion there are some fairly open stretches where cattle are raised and even small districts where semi-arid conditions prevail. The population of this heavily wooded wet lowland depends almost entirely on river transportation for all intercourse. The elevated mountainous plateaus of the three ranges are more open and more generally cultivated; all traffic is by means of horses, mules, and the burro. The canoe and river-steamer transportation systems of the valleys are connected with the highland system of trails and roads by short cross trails and the few short railroads of the country. As these cross trails must pass through the intermediate foot-hill region, where the heavy rainfall reaches its maximum, they are exceedingly bad and the life of pack animals is short. The oil development of the Magdalena River valley is in this intermediate region, between the river and the sierras, north of Bogotá.

Jan 9, 1922

By Fred W. Stiefel

To open the Fisher Hill mine of the Republic Steel Corporation, it was necessary to sink an inclined shaft into the rock and excavate stations, drifts, and ore pockets. This inclined shaft, or slope, q ft. 8 in. high by 28 ft. 2 in. wide, has compartments for two 5-ft. gauge ore-skip tracks of 120-lb. rail, one 5-ft. gauge man-skip track of 60-lb. rail, a concrete stairway, and service pipes consisting of a 12-in. compressed-air line, an 8-in. pump-discharge line, and a 4-in. water-supply line. When we were requested to investigate the work, the progress being made (by another organization) amounted to only 2 ½ ft. advance in 24 hr. We reported that progress of at least 6 ft. per day could be made. As a result, the Defense Plant Corporation, through the Republic Steel [ ] Corporation, entered into a contract with us to sink the shaft. The contract contained a penalty and bonus clause predicated upon an advance of 150 ft. per month. The average advance was 7.8 ft. per day; that in the best six-day week was 60 ft. and that in the best month, 215.5 ft. in 25 working days. The drilling was performed by 3 ½ -in. wet drifter drills mounted on five 8-ft. columns (see accompanying illustration). Even though a full-face drilling and mucking operation is customarily desirable, the steep slope, with the accumulation of water and fine debris at the face, made a modified heading and bench operation preferable. The heading and bench were of equal height. The five columns, instead

Jan 1, 1945

By J. G. Thompson

IRON, iron everywhere, but hardly a particle of pure unadulterated iron for the metallurgist to use as a base for the protean characteristics that he develops in the alloys of iron-the modern steels. Iron, next to aluminum the most abundant metal in the crust of the earth; one of the oldest metals known to man and serving him as the most indispensable metal in both war and peace; yet man's knowledge of its properties is based on specimens that are not pure and hence probably differ considerably in their properties from the truly pure metal. Purification of iron has brought about startling changes in its electrical and magnetic properties and has modified its behavior in changing its crystal form with temperature, the basis of the heat-treatment of iron. So both the research metallurgist and the metallurgist of the steel plant are intrigued by the possibilities that might unfold were 100 per cent pure iron available in sufficient quantities to determine its properties.

Jan 1, 1940