Search Documents

By L. D. Jaffe

From data found in the literature, a method has been derived for calculating hardenability of titanium alloys from their composition. A single graph gives the contributions of each alloying element. These are simply added to a base hardenability for unalloyed titanium. Results agree satisfactorily with measured harden-abilities. RECENTLY the importance of hardenability of titanium alloys in permitting attainment of high strength and hardness has become apparent. If a titanium-base alloy has adequate hardenability for the section size and quenching practice used, it can generally be heat treated to high strength and hardness either by simple quenching or cooling from temperatures near the ß transus, by quenching and tempering (aging), or perhaps by direct isothermal transformation of ß1,2 If the hardenability is inadequate, high strength cannot be attained. Preliminary charts translating hardenability requirements for shapes quenched in various media into terms of Jominy end quenched hardenability specimens or ideal round sizes are now available for titanium alloys." The method proposed in 1942 by M. A. Grossmann for calculating hardenability of steels from composition has proved to be of great practical value.' It appeared worthwhile to see whether, using information available in the literature, a corresponding method for calculating hardenability of titanium-base alloys could be derived. Data No systematic experimental study of the hardenability of titanium-base alloys has yet been made. There is available, however, a considerable quantity of scattered data bearing on hardenability. Some investigators determined Jominy curves on one or several alloys. Others reported as-quenched hardness for specimens of a few alloys cooled at various rates or in various media. Still others gave the as-quenched hardness for systematically varied composition, using one or several cooling mediums. The measurements utilized in this work were limited to hardness. Strength measurements were not used because a low strength may reflect high hardness combined with brittleness. Since, in general, the hardness of titanium alloys goes through a peak as the cooling rate is varied from extremely fast to extremely slow, the cooling conditions at which peak hardness was found were taken as the measure of hardenability.1,2 When as-quenched hardness was found to drop as the content of an alloying element (believed to increase hardenability) was raised, this was taken as an indication that the cooling rate was faster than that giving peak hardness; otherwise, the hardness should go up because of solid solution hardening. Also, if the hardness increased on tempering at low temperatures, this was again taken to indicate that the cooling rate had been faster than that giving peak hardness. Many of the data did not indicate precisely the cooling conditions for peak hardness but merely set a maximum or a minimum bound, or a bracket. Since the sizes of specimens quenched and the location of the hardness readings were not always given, it was occasionally necessary to estimate reasonable limits for them. Only the nominal compositions were available in some cases. As quenching from below the ß transus is equivalent to starting with a mixture of a and ß phases, whose individual composition would differ from the overall composition of the alloy, only measurements after quenches from above the ß transus were used. Hardness measurements on samples heated during metal-lographic mounting were also discarded. Because of their bulk, the data used will not be reproduced. They have been or will be published elsewhere.5-22 Approach All data were first translated into terms of ideal round size. For conversion from Jominy or quenched round or sheet, the author's graphs were used." For a few furnace cools or helium quenches where cooling rates were given, conversion was made on the basis of equal cooling coefficient.23 Plots of ideal round size for peak hardness against percentage of alloying element were next made for

Jan 1, 1956

By Percy Barbour

The town of Goldfield, Nevada, with the exception of six stone buildings, was burned to the ground to-day. One man is dead from causes attributed to the fire. A woman is missing and is believed to have perished and several persons were treated for burns as the result of the conflagration believed to have been of incendiary origin which started in the old Tenderloin District. The water supply was not sufficient and dynamite only scattered the frame structures and added kindling to the flames which were fanned by a forty-mile wind. Newspaper Dispatch, July 6. No former Goldfield resident could read that dispatch with unmixed feelings. About two o'clock one morning the crowded train from San Francisco landed me in Goldfield no more hours late than it habitually was. The desert air was clear and crisp and bracing but the pandemonium of cab and bus drivers did not drown out the sounds of music and merriment which floated from the blaze of light which was Goldfield about three-quarters of a mile from the station. As I stood in the ferry house, at the foot of Market Street, awaiting the Oakland Ferry, an old friend of mine, down to see who was departing for the greatest boom town of this generation, informed me that if I had made no reservation for quarters in Goldfield, I would be unable to obtain any, even chairs in the hotel lobbies were renting for $4 per night, and volun-teered the use of his room there for my convenience until his return. He described the house and location, which I identified without difficulty, but found no one to direct me to the room. I peered through a glass door into a room which seemed to be unoccupied and timorously entered and turned on the electric light., I found mail on the dresser addressed to my friend,

Jan 8, 1923

By George T. Bator

If confronted with the problem of pumping a mixture of slime-free sand, gravel and boulders up to six in. in diameter, at the rate of 175 tons per hr in one single-stage pump against a static head of 90 ft and a total head of 140 ft, of which 20 is on the suction side, an engineer might be forgiven for backing away from the job, especially if he were also told that the pump wearing parts must have a minimum hardness of 550 Brine11 for the sake of abrasion resistance. Yet precisely that feat has been accomplished in the gravel pit of John B. LaGarde, Inc., near Anniston, Ala. The pump used is of decidedly novel design and its successful operation since installation 1.5 years ago suggests that it may be of timely interest in numerous other applications in the mining industry, such as pump transportation of coal washer refuse or rock from open-pit's without unduly fine crushing.

Jan 9, 1950

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By ERNEST W. ELLIS

MORE or less contradictory findings as to the most satisfactory feed for concentration tables of the Wilfley type is shown by the diversity of opinion among experimenters. Prof. R. H. Richards,l as a result of his work, favors classification. On the other hand the work of Messrs. Cox, Gibbins, and Porter,' of McGill University, points in general to the desirability of screen-sized feed The ore used was obtained from the West mill of the Bunker Hill and Sullivan Mining and Concentrating Co., Kellogg, Idaho, and consisted of argentiferous galena in a gangue of quartzite and siderite. The natural feed was taken from the launder supplying the Fahrenwald classifier. Classified feed was collected from each of the ten spigots of this same classifier. From the natural feed the screen-sized feed was pre- pared in the laboratory. All three types of table feed were therefore derived from the actual mill circuit of a large plant.

Jan 1, 1926

By J. F. Myers, R. J. Tower

"THERE is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. GENERAL EQUIPMENT A signal light to show that a steel bin, containing relatively fine, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.3 To spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1947

By J. F. Myers, R. J. Tower

"There is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. General Equipment A signal light to show that a steel bin, containing relatively line, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.' TO Spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1949

ZAY JEFFRIES (communication to the Secretary*).-Having seen Mr. Ruder's micrographs of electrolytic iron, I am of the opinion that the tentative explanation offered verbally is correct. Mr. Ruder has informed me that both of the samples were cooled in the furnace. The structures as shown in Figs. Band C resulted from the last cooling through the temperature range near 900° C. Assuming that the rate of cooling through this range was the same in both cases, the differences in struc-ture of the gamma iron in the two samples must have ]:)]-ought about, in some way, the variations in grain size and grain shape shown in Mr. Ruder's micrographs. Even though there is practically no temperature gradient in muffle-furnace treatment during the "soaking" period, during both heating and cooling, there is a temperature gradient. Fig. B should normally have been fine-grained prior to the last cooling, due to the comparatively low maximum temperature to which it was heated (1,000° C.). On cooling through the allotropic change point at 900°, these small gamma grains, iii conjunction with the temperature gradient, should form an ideal condition for germination. Germinant grains should form near the surface of the sample (the-colder portions) and the small gamma grains would be progressively absorbed as they changed into non-gamma iron. The elongated grains in Fig. B, converging toward the axis of the piece of iron, indicate that germinant grains first formed near tine surface and advanced their boundaries toward the interior of the sample. The gamma grains in Fig. C, however, should have been large, prior to the last cooling, due to time high temperature treatment (1,250 to 1,300° C.). In other words, to use one of Prof. Howe's expressions, the crystalline organization should be very complete and the change from gamma to non-gamma iron on cooling would take place reluctantly. This resistance to change from gamma to non-gamma iron would probably be greater in the interior of the large grains than at their boundaries. Non-gamma iron centers or nuclei would probably form at a great many places, at the grain boundaries, thus masking the influence, to a large

Jan 6, 1917

By T. L. Chu, G. A. Gruber

Silica films hare been rleposited 011 silicon substmtes at 400° to 600°C by a chemical-transport technique using hydrogen fluoride as the transport agent ill a closed system. This transport takes place from a source materia1 1071: temperature to substrates at higher temperatures, as indicated by the thermochemistry of the transport reaction. The experimental variables of- the transport process, such as the substrate temperature, the pressure pi the transport agent, and so forth, have been studied. The rate -determining step of the transport process appears to he the ),ale of chemical reaction in the source region. The transported films are similar to thermally grown silica films in physical proper-ties with the exception of 'some what higher dissolrrtion rates. SILICA films deposited on suitable substrates serve many purposes in electronic devices. They are used for the fabrication of tunneling devices, the surface passivation of devices, and the shielding of devices from nuclear radiation: and as selective masks against the diffusion of specific impurities into semiconductors. Doped silica films can also be used as sources for the diffusion of impurities into semiconductors. Several oxidation and deposition techniques for the preparation of silica films have been developed to meet the requirements of these applications. The therma1 oxidation of silicon by oxygen or steam at temperatures above 900 C is commonly used in silicon technology. The deposition techniques are perhaps more advantageous since they usually require lower temperatures and are not limited to silicon substrates. Silica films have been deposited on silicon and other substrates by reactive sputtering and chemical reactions. The sputtering of silicon in an oxygen atmosphere is capable of depositing good-quality silica films on silicon' and gallium arenide. Many chemical reactions are known to yield silica at room temperature or higher. These reactions may involve intermediate steps. However, the final step yielding silica should take place predominately on the substrate surface in order to produce adherent films. When silica is formed in the gas phase by volume reactions, no adherent deposit can be obtained. Generally, the experimental conditions of a reaction can be varied so that the surface reaction predominates over the volume reaction. The chemical reactions which have been used successfully for the deposition of silica films are briefly as follows. The pyrolysis of alkoxysilanes in an inert atmosphere or under reduced pressure has been employed to deposit silica films on germanium3 and silicon4 at 650" to 750°C in a flow system. The deposition of silica films from alkoxysilanes has also been achieved at nearly room temperature by a low-pressure plasma. Device quality silica films have been deposited on germanium and gallium arsenide by the deposition of an amorphous thin silicon film followed by oxidation at 600" to 700" . Silica films for high-temperature capacitors have been produced by the hydrolysis of silicon tetrabromide at 950°C in argon and hydrogen atmospheres.7 We have developed a chemical-transport technique for the deposition of silica films on semiconductor substrates at relatively low temperatures. The thermochemistry of the transport reaction, the experimental variables of the transport process, and the properties of the transported silica films are described in this paper. THERMOCHEMICAL CONSDERATIONS The transport of solid substances by chemical reactions in the presence of a temperature gradient has been used for the preparation of films and crystals of many electronic materials. In this technique, a gaseous reagent is chosen so that it reacts reversibly with the solid substance under consideration to form volatile products. Since the equilibrium constants of most reactions are temperature-dependent, the transport of these products to regions of suitable temperature in the reaction system would cause the reverse reaction to take place. depositing the original solid. When the equilibrium is shifted toward the formation of the solid as the temperature is decreased, the solid is transported from a high-temperature zone to a lower-temperature region, and vice versa. This chemical-transport technique can be carried out in a closed or gas-flow system. In a closed system, chemical equilibrium is presumably established in the different temperature regions of the system, and the transport agent regenerated in the deposition region repeats the transport process in a cyclic manner. The local chemical equilibrium may not be approached in a flow system: however, this system offers a greater degree of flexibility. Silica reacts reversibly with hydrogen fluoride and this reaction was chosen for the transport process. The over-all reaction between silica and hydrogen fluoride may be written as: SiO2(s) + 4HF(g-) = SiF4Ur) + 2H2O(^)

Jan 1, 1965

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By A.E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By A. E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By R. H. McLean

Velocity, kinetic energy and shear in crossflow beneath three-cone jet bits may influence cleaning of the bottom of the borehole and the teeth of the bit. Laboratory investigation shows that each of these parameters is a function of the diameter of the borehole and the product of the volume rate of flow and velocity through the nozzles (QVn). Increasing QV, or decreasing the diameter of the borehole increases each parameter. These functions provide means of predicting the magnitude of each parameter and of scaling the cleaning forces. INTRODUCTION In drilling operations using conventional jet-type rock bits, the impinging jels create an important flow mechanism. Called crossflow, this flow mechanism originates in the impact area of the jets, spreads across the bottom of the hole and supplies the principal source of energy to clean the teeth of the bit and most of the bottom.' Besides providing the means of cleaning cuttings from the bit and the hole bottom, crossflow may also have other, less direct, effects on the rate of penetration. The shear stress generated on the bottom by crossflow will inIluence the thickness and permeability of any filter cake of mud solids or crushed material which forms on the bottom.' These factors may affect the rate of penetration. A previous pulblication introduced some fundamental concepts of crossflow.' Crossllow was shown to occur in a thin layer adjacent to the bottom, and to cover the bottom completely. The maximum velocity in the crossflow above any position on the bottom was found to be directly proporlional to the square root of the product of the volume rate of flow and velocity through the nozzles—the jct QV,,—and inversely proportional to the diameter of the borehole. This information indicated that the effectiveness of crossllow in scavenging the bottom can be improved by maximizing the jet QV. The investigation reported herein amplifies the definition of crossflow. Complete velocity profile data above a representative position on the bottom are analyzed. These data better illustrate control of the capacity of crossflow to scavenge the bottom, and also relate shear stress on the bottom to known, controllable parameters. The conclusion reached in the previous publication that maximization of the jet QV. produces the maximunl cleaning beneath current jet bits is unchanged by these new data; rather, it is strcngthened. Data presented here show that the kinetic energy flux above a representative position on the bottom is maximized by maximizing the jet QV. The shear stress on the bottom will also be shown to be maximized in the same manner. Since the functions relating the jet QV. to velocity, shear stress and kinetic energy also involve the diameter of the borehole, means of equating, or scaling, these quantities in different sizes of boreholes will be illustrated. EXPERIMENTAL EQUIPMENT AND TECHNIQUE JET BIT MODEL Data were recorded from the same laboratory model as used in the aforementioned investigation of the flow around a jet bit.' The model consisted of a 43/4-in. three-cone, jet-type rock bit in a smooth, flat-bottomed borehole constructed of lucite. The bit had a shape and nozzle placement closely resembling larger three-cone jet bits commonly used in field operations. Fig. 1 illustrates the impact area on the bottom of a jet from this bit. Details of the orientation of the jets may be found in the previous publication. TECHNIOU'E OF MEASUREMENT Measurements of the crossflow were made by inserting a very small Pitot tube through the bottom of the simulatetl boreholc. Extreme thinness of the layer of crossflow necessitated accurate measurements of the height of the Pitot tube above the bottom to achieve close definition of the velocity profile. A cathetometer, which could be read to the nearest 0.005 cm, was used to make this measurement.

Jan 1, 1966

National Society of Professional Engineers has thrown its full sup- port behind pending legislation to appropriate $500 million for national conversion efforts that would provide employment opportunities for engineers, scientists, and technicians who are currently unemployed because of the decline in defense and aerospace programs. Known as the Davis-Giaimo bill, the proposed legislation would raise total Federal investment in science and technology to an adequate annual spending level and keep it proportionally equal to the growth in the GNP. If passed, the bill would increase and maintain Federal obligations for civilian-oriented research and development activities to a parity level with similar obligations for defense research development. U. S. Bureau of Mines has cataloged and placed on open file an inventory of U.S. coal deposits which can be economically strip mined at today's production costs. The costs include charges for reclaiming the mined land as required by 21 states. The report claims that some 46 billion tons of bituminous coal and lignite can be strip mined under present economic conditions, and that 32 billion tons of the total is classified as having less than 1% S. The report reviews strippable coal deposits by state, by county, by coal seam, by coal-seam thickness and by sulfur content. The report also gives an up-to-date summary of state laws on surface mine reclamation. Open-file copies of "Strippable Reserves of Bituminous Coal and Lignite in the U.S." may be consulted in Washington, D.C., at the Department of the Interior library and at U.S. Bureau of Mines offices in Pittsburgh, Denver, San Francisco. Dallas. Spokane, and Douglas Island, Juneau. Alaska.

Jan 1, 1971

By O. D. Gonzalez, H. A. Wriedt

Alloys ranging from pure iron to pure nickel were saturated with nitrogen gas at 918°, 999°, and 1217°C and analyzed. The solubility of nitrogen at 1-atm pressure was obtained as a function of nickel content for the whole range of iron-nickel alloys and the temperature dependence of solubility is shown for the experimental alloy compositions. The heat of solution and the entropy of solution of nitrogen in the alloys as func-tiom of composition up to 41 pct Ni are given. 1 HE acquisition of more exact thermodynamic information for systems composed of iron with various alloying elements continues to interest ferrous metallurgists. The interstitial alloying elements, especially carbon, hydrogen, and nitrogen, comprise a field of particularly intense study. A recent investigation of carbon solubility in Fe-Ni alloys held at 1000°C in gases of fixed carbon activity showed an unpredicted minimum in the solubility near 72 pct Ni.1 The present investigation was undertaken to see if a similar anomaly in solubility existed for nitrogen in Fe-Ni alloys. The solubility of nitrogen in ? iron at known nitrogen activities has been measured several times.&apos;-&apos; Corresponding information for the solubility of nitrogen in solid Ni and Fe-Ni alloys is not available. Juza and sachsze9 reported that metallic nickel dissolved 0.07 pct N in equilibrium with Ni3N at 445°C. This result was regarded as dubious by Turkdogan and Ignatowicz10 who found less than 0.0004 pct N in nickel specimens equilibrated at 600°C with ammonia-hydrogen mixtures having fugacities of N2 gas up to 35,000 atm. Such fragmentary reports indicate only that nitrogen gas has a very much lower solubility in nickel than in iron. MATERIALS A purified iron from Battelle Memorial Institute was used for solubility measurements. This grade contained more than 99.95 pct Fe, the highest content of any measured individual impurity being 50 ppm for each of As, C, Cu, and Pb. The nickel and iron-nickel alloys, supplied by the International Nickel Co., contained 0.02 to 0.04 pct C, 0.17 to 0.19 pct Mn, 0.04 to 0.08 pct Si, < 0.01 pct P, <0.03 pct S, and <0.20 pct Co as principal impurities. The Fe-0.59 pct Mn alloy was of zone-melted quality, the highest concentration of any individual impurity being 15 ppm Al. The "prepurified" grade of nitrogen gas from Matheson Co. had a nominal nitrogen content of 99.996 pct. An "electrolytic" grade of hydrogen gas from National Cylinder Gas. CO. in which the principal impurity is water vapor was admixed with the nitrogen to prevent oxidation of these specimens. This grade was preferred to a purer grade because the presence of some oxygen helps in suppressing contamination of the specimens, for instance, by silicon from the porcelain furnace tube. EXPERIMENTAL PROCEDURE The specimens were equilibrated in vertical tube furnaces through which a 99 pct N2-1 pct H2 gas was passed at ambient pressure. For the 915", 918", and 999°C runs, a wound-resistance furnace was used, and for the 1217°C runs, a furnace with a tubular silicon carbide element was used. The temperature control system on both furnaces was similar: a Weston "Celectray" controller with a modulator, responding to the electromotive force of a thermocouple with its hot junction in the furnace, switched the furnace current between high and low settings. The temperature distributions in the working zones of the furnaces were determined with calibrated Pt/Pt-10 pct Rh thermocouples. The overall uncertainty in temperature was estimated to be ±3° at 915° to 999°C and ±5° at 1217°C . Consideration of the small temperature coefficients of the equilibria studied, together with the error limits in the method of analyzing for nitrogen, showed that further refinement in temperature uniformity would give no improvement in resultant accuracy. The reactive gas was generated by mixing together "prepurified" nitrogen and "electrolytic" hydrogen directly from cylinders commercially supplied. The flow rates of nitrogen and of hydrogen were fixed by setting with bleeders the pressure drops across the individual calibrated flow meters of constant resistance. For any given alloy, the solubility of nitrogen at 1-atm pressure (% N) was obtained from the analyzed nitrogen content of equilibrated specimens (% Na)according to Sieverts&apos; law, thus

Jan 1, 1962

The following is an incomplete list of members and guests who. called at Institute headquarters during the period Dec. 10, 1917 to Jan. 10, , 1918: A. A. Arluck, Camp Merritt, N. J. W. Spencer Hutchinson, Boston, Mass. C. L. Bruns, Santiago de Cuba. William F. Jahn, New York, N. Y. Henry C. Carr, New York, N. Y. C. H. James, Tucson, Ariz. L. J. Charles, Santa Fe, N. M. Charles Janin, San Francisco, Cal. W. A. Deane, Waxhaw, N. C. Joseph T. Kupferstein, Shreveport, Pa. P. St. John Dixon, Rio de Janeiro, Brazil. Richard Lamb, New York, N. Y. M. C. Drake, Marquette, Mich. Walter R. Malm, San Francisco, Cal. F. W. Draper, Petrograd, Russia. W. H. Nash, Buffalo, N. Y. Paul W. Gaebelein, Boise, Idaho. Edmund Newton, Minneapolis, Minn. H. F. E. Gamm, Rutherford, N. J. Guy C. Riddell, Port Pirie, South Australia. C. A. Grabill, El Paso, Tex. Williams A. Simkins, San Francisco, Cal. William H. Hampton, New York, N. Y. Henry B. Smith, Northampton, Mass. R. M. Henderson, Brackenridge, Colo. H. E. Smith, Chicago, Ill. Geo. B. Holderer, Northpines, Ont., H: C. Spaulding, Washington, D. C. Canada. Y. Wakabayashi, Tokyo, Japan. H. H. Howry, Camp Upton. N. Y. A. P. Watt, Mine La Motte, Mo. L. Douglas Anderson", superintendent of the Midvale, Utah, smeltery of the United States Smelting Co., has been appointed manager of smelteries for the company at Salt Lake City, Utah.

Jan 2, 1918

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By Nicholas J. Grant, Ulf Kalling, John Chipman

D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—I would like to know what evidence you have to prove the MnO was pure MnO. I would also like to know whether you might not explain it on the basis of a temperature reversion; and, was it due to the oxidizing power of MnO? N. J. Grant (authors&apos; reply)—Briefly, we have no proof that pure MnO was used. The manganese oxide was added as chemically pure MnO,. MnO is assumed as the oxide in the reacted slag following standard molecular slag theories, especially under the reducing conditions of these experiments. The noted sulphur reversion cannot by any means be explained on the basis of a temperature reversion since the temperature effect is shown in this paper to be very small. Until a more logical explanation can be offered, backed I hope by some experimental proof, we propose to explain this sulphur reversion as stated in the paper, namely, that it is due to the oxidizing effect of the added manganese oxide. Member—How did the oxygen in the slag give you a reversion of sulphur? What was the mechanism there?

Jan 1, 1952