Search Documents

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

By ARCHIBALD DOUGLAS

BY this time almost everyone knows, in a general way, the corporate income distribution policies of the 1936 Revenue Act, and many of the practical problems arising there under. This article is not intended to be a technical discussion of that act by title, subtitle, section, or supplement, nor an analysis of inter- dependent sections of the various acts over many years woven on the fiscal loom f our Congressional machine. Such a discussion would require the spinning of a web of words too long for patience. Yet ,a general statement of the underlying plan of the 1936 Act, so far as it affects dividend policies, is perhaps useful.

Jan 1, 1937

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By Ian MacGregor

INTRODUCTION I retired in 1977 and have been enjoying myself ever since doing odd jobs for various people - on occasions, politicians. I commend it to you as post retirement - get involved in situations that nobody else will take on. It produces all sorts of excitement, it is a lot of fun and, courtesy of the media, you provide great raw material for their current Punch and Judy shows. The example of the adventures in the Escondida financing made me think about the history of the minerals industry in the United States. In order to see more clearly what is going to happen in the future, we have to look at the past and what we have learned, and try to extrapolate from that a scenario for the future. This paper is about global material cycles and the financial needs of the extractive industries. Since about 2,000 years B.C. we have been living in the Iron Age. Since about 4,000 B.C. we have been living in the Copper Age. These have been the two foundations of modern industrial society. Understanding the use of metals and materials helps us understand the civilization in which we live today. Let me focus more closely on the United States, particularly in this century. In the first two-thirds of this century the United States was growing and expanding and developing. It was providing for its inhabitants a society which was enjoying the benefits of a rising standard of living, improved opportunities and the ability to support a population growing at quite a dramatic rate. It is still growing. In the Department of Commerce, there is a clock that shows how many people there are in the United States. It turns all the time; the numbers are going up. On January 21,1980, when Ronald Reagan was sworn in as President, the number on that clock was a little over 220 million, and in the last week before he left, it was travelling towards 245 million. During his period in Washington, we have added , the equivalent of one total state such as California. That gives the dimensions of the U.S. appetite for raw material inputs. The inputs are of critical importance. COMPARATIVE ADVANTAGE During the first two-thirds of this century, the minerals sector enjoyed comparative advantages. There was a clear understanding of the importance of minerals enshrined in the tax legislation of the country from the early decades of this century - the depletion allowance. No other country identified as clearly that the supplies of minerals were finite. As they are used up, just as with a wearing-out machine, one must get capital back to replace the resource when the time comes. Within the last decade, that idea has been questioned and criticised. It is now seen as giving money away to a preferred part of the economy, instead of recognizing what depletion is all about. In previous times it insured that the U.S. always was able to regenerate the capital in its minerals industry, so that it could remain competitive. The U.S. had plenty of everything, including energy. We had a growing population. Equally important, we had an agriculture that led the world in productivity, even as far back as the turn of the century. It continues to do so. We still retain that comparative advantage, an ability to produce our foodstuffs in quantity and quality at excellent cost. Look at another ingredient of our comparative advantage, the energy position. We ran through the first two-thirds of the century with ever- decreasing energy costs. In the 1940s and 1950s the coal industry went into a decline. Why? Because the $3.00 - $5.00 a ton cost of mining coal in the U.S. represented relatively expensive energy. A ton of good grade bituminous coal contains 25 million BTU's. $0.20 a million BTU's represents $5.00 a ton at the pithead. That price was undermined by the increasing ability to find petroleum at even lower costs. At the apex of the growth of development of the American dominated

Jan 1, 1990

By H. J. O’Donnell, B. C. Parks

IN 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.l The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogenation properties of certain American coals. In the years following adoption of Thiessen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring instrumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. PETROGRAPHIC COMPONENTS AND TYPE CLASSIFICATION OF COAL Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1948

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.' The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

By John Johnston

The actual amount of any metal volatilized from a mixture of metals depends on the magnitude of its partial vapor pressure under the specified conditions of temperature, and on the circumstances attending the heating—in particular, on the duration of heating, the volume of gas coming into actual contact with the surface of the metal, the extent of this surface, and the rate of diffusion of the volatile metal from the body of the melt toward the surface.' If two (or more) metals are volatilizing from the same mixture of metals, the several conditions are identical except for the difference in partial pressure and in rate of diffusion of the volatilizing metals; the second of these two factors is without doubt only of secondary importance as it is probable that the rates of diffusion of the volatilizing metals would be very similar. Hence, in order to gain an estimate of the relative amounts of two metals that may be volatilized from a given mixture, it is necessary to know the vapor pressure, or, more precisely, to ascertain for each metal its partial vapor pressure in equilibrium with the liquid (or solid) alloy under the particular circumstances. The partial pressure of each constituent depends on the effective concentration of that constituent in the alloy2 as well as on the vapor pressure of the constituent when pure, and it can be calculated when both of the above factors are known. The first step, therefore, is to ascertain the vapor pressure of the several pure metals. Vapor Pressure of Pure Metals The experimental data on the vapor pressure of the several pure metals with which we are here concerned are not so accurate as could be wished, nor have the determinations been made in general at temperatures such that the results can be used directly. In a previous

Jan 1, 1919

By Floyd C. Kelley

THE literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough investigation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibrium produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizing1 which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. DIFFUSION OF METALS IN IRON It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

Jan 1, 1928

US 4,134,944-Production of iron oxide ore pellets of uniform size and excellent strength. Small pieces of ore are rolled into nuclei in a first pellet-rolling circuit in the presence of a binder, the nuclei sized and hardened by sintering or cold-bonding of the binder, the nuclei rolled in additional ore to form product pellets, the pellets sized, the suitable size fraction taken as product, and undersize pellets returned to the rolling operation. P. A. Ilmoni and R. Drugge, assigned to Luossavaara-Kiirunavaara AB Jan 16, 1979. 5 pp. (264-37) Filed- 5-25-77 (800,278) Priority: Sweden, 6-2-76 (76/06,¬241). Same British 1,553,763, dated Oct 10, 1979. US 4,145,210-In the induration of pellets of iron oxide ore or iron works dust or sludge, a charge of dried pellets and 2-20% by weight of coke having a size range of from 5 to 30 mm, a drum index of more than 70, a reactivity index of less than 50, and a tumbler index of more than 50 is charged into a rotary kiln The charge is heated and passed through the rotating kiln to indurate the dried pellets without burning the coke Powder-coated coke is recovered from the kiln for reuse. Ring formation in the kiln is substantially prevented. K. Kato and K Kadota, assigned to Sumitomo Metal Industries, Ltd, and Sumitomo Heavy Industries, Ltd. Mar 20, 1979 10 pp (75-3) Filed- 2-22-77 (770,947) Priority: Japan, 2-24-76 (51/19,754) US 4,145,211-Method of cooling hot metallized iron oxide ore agglomerates from a direct reduction furnace Agglomer¬ates ranging from 3/a in to 41/2 in in cross-section and at a temperature of 1000-2000°F are formed into a moving bed while at rest relative to each other Air at ambient tempera¬ture is passed through the bed at a velocity sufficient to cool the agglomerates rapidly to a temperature no greater than about 500°F without substantial reoxidation of the metal in the agglomerates and by using air as the sole cooling gas. C A Czako, A Berzins, and M J Greaves, assigned to Arthur G McKee & Co Mar. 20, 1979 15 pp. (75-34) Filed: 7-18-77 (816,467)

Jan 1, 1980

By W. P. Shinn

In a paper contributed by W. A. Goodyear, M.E., on "Water Gas as Fuel," read at the Boston Meeting, February, 1883,* the following statenlent was made: "The latest experiments on a scale of some magnitude in our citier, in the way of heating buildings and furnishing power for manufacturing purposes, have been by the distribution of high-presslire steam through pipes laid in the streets. Hilt these experiments (1) have not hitherto been very successful; and when we consider the high cost and (2) the great and unavoidable loss of heat and power, which always accompany the conveyance of high-pressnre steam to any considerable distance in pipes, to say nothing of (3) certain practical difficulties in the management of the pipes themselves, (4) it is evident that all such methods must eventually disappear before a system which can furnish a cheap gas of great heating power, easily distributed wherever wanted, without requiring pipes to stand pressures of 50 to 75 pounds per square inch, and (5) without keeping the whole mass of ground in the streets through which it passes hot, gratis, for a distance of ten or fifteen feet, in all directions around the pipes!' For the purpose of controverting Mr. Goodyear's statements in regard to steam-distribution in cities, I hare numbered the points made in his indictment, my principal object being, not a professional discussion of the technical and theoretical merits of steam vs. watergas, but a simple statement of facts, in regard to the present state of the street system of steam distribntion. Taking Mr. Goodyear's points in their order: 1. Concerning what he terms " These experiments," saying that they " have not hitherto been very successful," I propose to show, that the problem of stearn-distribution has passed beyond the experimental stage, and that its practical solution is highly successful. This will be shown by the facts hereinafter fully set forth. 2. "The great and unavoidable loss of heat and power whicn always accompany the conveyance of high-pressure steam to any con-

Jan 1, 1884

By A. S. Yue, A. G. Guy

A study was made of the effects of a prolonged flux of zinc atoms through the a solid solution of zinc in copper. The experimental arrangement consisted essentially of a copper disk about 0.01 in. thick, at one of whose surfaces a gaseous atmosphere containing zinc atoms was maintained, and at the other surface a gaseous atmosphere with a minimum of zinc atoms was maintained. During prolonged theothersurfaceexposure at high temperatures the zinc content of the copper disk gradually built up to the steady-state concentration distribution and then remained at this value. The concentration-distribution curves for various conditions were determined by chemical analyses. The results showed that the condition of steady-state diffusion was achieved. The diffusion coefficients calculated from the experimental data, although not of high precision, agreed with the values obtained by other workers using unsteady-state methods. Relatively slight porosity developed in the specimens in the course of diffusion. A LTHOUGH most diffusion studies have been made under unsteady-state conditions, it is known' that the steady-state method is often superior with respect to the directness and accuracy of interpretation of the data. Steady-state diffusion of gases through metal diaphragms is well known. Also, Harris' and Smith" have used the steady-state method in studying the diffusion of carbon in aus-tenite. The accepted mechanism in this system involves the motion of the interstitial carbon atoms in the rigid framework of the lattice of iron atoms. Thus, there is little difficulty in visualizing the steady flow of the small carbon atoms through the austenite. The situation in substitutional diffusion is quite different. Here the atoms are comparable in size, and it is not evident how a steady flow of one of the atoms through the solid solution might be achieved. At the time the present research was started, it was known that a previous exploratory attempt to produce steady-state diffusion in a substitutional alloy, the Au-Ag system,' had been unsuccessful and had indicated that perhaps there were basic difficulties that could not be ovei-come. Therefore, the present research began as a study of the effect of a prolonged flux of metal atoms through a substitutional solid solution. Eventua.lly, it was possible to produce actual steady-state diffusion in the system chosen for study, the a Cu-Zn alloys. Experimental Procedure The aim in the experiments was to maintain a high zinc content, about 30 pet, at one surface of a copper sheet, and to maintain a low zinc content, near 0 pet, at the opposite surface. The zinc would then diffuse into and through the copper, first building up to the steady-state concentration distribution and then maintaining this distribution. The three types of specimens that were used are shown in Fig. 1. In type A specimens the copper disk through which diffusion occurred was welded to the top of a cylindrical molybdenum tube, the bottom of which also was sealed by welding. At the diffusion temperature the brass chips in the molybdenum container were the source of the zinc vapor which maintained the lower surface of the copper disk at 30 pet Zn. The upper surface was maintained at 0 pet Zn by the vacuum in which type A, and also type B, specimens were diffused. Since the molybdenum container was impervious to zinc vapor, it was intended that the only path of escape for the vapor from the brass chips would be through the thin copper diffusion disk. However, it was found that small leaks often developed at the welded joints during the diffusion treatment, and in most specimens some of the zinc was lost in this manner. Although even small losses of this kind were a serious handicap in attempting to determine the flux through the disk, they did not prevent the maintenance of satisfactory boundary conditions for the attainment of the steady-state condition. Type B specimens differed from type A in having a weight of about 300 g supported on the copper disk by 15 to 20 short quartz rods. This change was made when it was observed that the copper disk was being bowed upward by the difference in the pressures acting on its two surfaces. Since the grain-boundary cracking which occurred in the bowed specimens could be attributed largely to the accompanying creep,3 it was desirable to minimize this effect. The counterweight was effective in significantly decreasing both bowing of the disk and cracking at grain boundaries. Type C specimens differed considerably from the others in that the low-zinc atmosphere at one sur-

Jan 1, 1959

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By Edward C. J. Urban

THE nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than to years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini¬tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. DEVELOPMENT OF ROCK DRILLS The earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its piston-type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1947

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators 1-5 have noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilities6 and by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported' to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of this portion is shown in Table I and an approximate mineralogical analysis is shown in Table II. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of -6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1952

By Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dis-sociated in the liquid state, as indicated by the continuous for in of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a =6.52, b = 8.60, c = 4.16 A.2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb From the known free energies of formation of CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By J. A. Porter

In offering some data relative to this property, and the treatment of its ores, it is proper to say that a purely scientific article has not been attempted. It is hoped, however, that the economic conditions presented may be of interest to the members of the Institute, and that a discussion upon the concentration of the ore may throw some light upon a very unsatisfactory part of the work. The Smuggler-Union mines are located at the head of the San Miguel river, just south of the water-shed between Ouray and Telluride. The latter town, reached by the Denver and Rio Grande railway, is most picturesquely situated, at ail altitude of 8500 feet, in a narrow valley, the lower portion of which exposes only the sedimentary rocks. Along the sides of the valley, large masses of coarse alluvial deposits are left high above the present channel of the stream. Although much placer-work has been done, and some very rich material has been found, the limited extent of the isolated tracts has made placer-mining in this locality generally unprofitable. The valley terminates two miles above Telluride in an amphitheater around which walls rise abruptly several thousand feet. Here the company's mill is situated, being reached by a Bleichert tramway from the mines and also by a spur of the Rio Grande railway from Telluride. At this point, not only are the reddish sandstone and conglomerate beds exposed, but the contact between the conglomerate and the overlying gray volcanic breccia is plainly in view, even at a distance of many miles. A marked stratification is noticeable, indicating the successive layers of igneous breccia, locally termed trachyte. Throughout the entire region this is the favorite name among the miners for the rocks composing the igneous cap of the San Juan

Jan 1, 1897