Search Documents

By C. R. Barker, D. A. Summers, H. D. Keith

Introduction Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these areas has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generaly have been short in length, although where methane drainage operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the federal government, methods have also been developed for draining coal seams of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes. Development of methane drainage has recently been encouraged by the potential use of the drained methane as a commercial energy source, with a need, therefore, to adequately organize a collection system, separate from mining the seam for coal. This has already been successfully accomplished, for example, in the Federal No. 2 mine of Eastern Associated Coal Corp. starting in 1975 (Johns). However, whether the system gains access to the coal through horizontal drilling from a pre- existing mine or via access through a separate shaft from the surface, long horizontal holes are required to adequately tap the methane reserve. It is to this regard-the actual drilling of the horizontal holes-that this paper is directed. It will examine potential benefits that may accrue, both in conventional horizontal hole drilling from a mine site underground, and also in drilling from the surface if a high pressure water jet drill is used to drill the degasification holes. Long Hole Drilling from an Underground Site Personnel from the Bureau of Mines have recently examined methods for conventional drilling of long horizontal holes to gain access for methane drainage. They have shown that it is possible (Cervik, Fields, and Aul) to drill out some 610 m using a conventional drilling system. Three types of bit were used in the program and by alternating between a drag bit, tricone bit, and plug bit, advance rates of between 0.6-3.6 m/min were achieved. Hole diameters varied from 7.6-9.2 cm in surface tests at bit thrusts of 1360 kg. A hole was then drilled and maintained in relative alignment within the coal seam for a distance of 640 m. Thrust levels had to be lowered to between 363-680 kg across the bit. Because the loads were smaller than those used in the surface trial, advance rates in the hole were of the order of 10-38 cm/min. The thrust level was lowered since it was found that the level of the thrust controlled the inclination of the drill so that, for example, a thrust of 363 kg caused the hole to incline downward, while at greater than 544 kg the hole inclined upward with the 9-cm-diam bit. Thrust levels increased 227 kg when the hole diameter was raised to 9.2 cm, although in such a case penetration rates in excess of 56 cm/min could be achieved. Horizontal Water Jet Drilling of Coal The University of Missouri-Rolla has recently undertaken research for Sandia Laboratories on the use of high pressure water jets as a means of drilling through coal. The initial experiment in this program called for drilling a hole horizontally into a coal seam from the side of a strip pit using water jets as the cutting mechanism. A very simple setup [(Fig. 1)] was used in this program and a 15-m hole was drilled at an approximate drilling speed of 1.2 m/min. The nozzle was designed so that the hole dimension was approximately 15 cm across [(Fig 2)] and the thrust was maintained at levels below 91 kg in moving the drill into the coal face. The system used was very crude and comprised a high pressure water jet drill enclosed within a 5.7-cm outer diameter galvanized water pipe to provide rigidity to the drilling system. This pipe sufficed to maintain hole alignment over the 15-m increment. While it is premature to make long-term predictions on ultimate applicability of this sytem to long hole drilling, certain inherent advantages of water jets can be delineated from research results and suggest considerable advantage to further research in development of this application. High pressure water was supplied at approximately 62 046 kPa from a 112-kW high pressure pump, with a 83 L/m flow through the supply line to the nozzle. The drilling system consisted of a nozzle rigidly attached to the front end of the galvanized piping. High pressure fluid was supplied to this nozzle through a flexible high pressure hose that fed from the nozzle back through the galvanized pipe to a rotary coupling attached

Jan 1, 1981

By L. Segle, R. Resnick

NUMEROUS experiments in the past few years have proven that void formation occurs quite generally in the diffusion zone of bimetal specimens1-4 The phenomenon has been explained in terms of the accumulation of lattice vacancies resulting from unequal diffusion of the constituents and their eventual precipitation as holes.= Attention has recently been directed to the fact that voids also form within homogeneous metals during high-temperature creep.' The idea has been put forward that these voids form by the condensation of excess lattice vacancies generated by intersecting dislocations.".' If the precipitation of lattice vacancies from solution is treated as a nucleation and growth process, the predicted vacancy concentration for homogeneous nucleation of voids at an observable rate is 100 to 1000 times the normal thermal equilibrium concentration. It appears that voids actually form during diffusion at vacancy supersaturations which are much lower than this8 According to the calculations of Machlin,' the same must be true for voids formed in homogeneous metals during creep, if these are considered to arise from the precipitation of lattice vacancies. Therefore, if the vacancy mechanism is valid, it seems that the holes which form in diffusion and creep specimens are heterogeneously nucleated by imperfections or impurities in the metal. Irregularities in the frequency and distribution of voids in diffusion couples bear out this explanation.' , It is not known at the present time what the nuclei are on which vacancies condense. Various investigators have speculated that they could be certain dislocation configurations, already existing voids produced during solidification or working, gas pockets, or inclusions in the metal. Relatedly, the precise value of the degree of vacancy supersatura-tion for void nucleation is still uncertain. An initial attempt to estimate this value from diffusion data, made by Balluffi, indicated that voids form in diffusion couples at vacancy concentrations which may

Jan 1, 1958

By T. K. Perkins, W. W. Krech

Jan 1, 1969

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

By James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

By William Kelly, Frederick Laist

The slow, tedious and costly method of reducing copper matte to metallic copper in the reverberatory furnace, commonly known as the Welsh process, was displaced by the rapid and inexpensive converter process about fifty years ago. The art of refining copper was for many generations a carefully guarded secret among the Welsh furnacemen and was handed down among them from father to son. An attempt was made to apply it at Butte when the smelting of copper ore first started there but it proved too difficult and expensive under local conditions, and until the introduction of the converter process the entire output of copper was shipped to Swansea in the form of high-grade (60 per cent) matte. Before the construction of the Manhes converter, attempts had been made to reduce copper matte in the bessemer steel converter, but these failed, chiefly because the air was blown through the bottom of the vessel. The air holes became clogged with chilled copper as soon as the reduction started. Manhes partially overcame this difficulty by placing the tuyeres in the side of the vessel, some, distance above the bottom, thus allowing space beneath them for the copper to accumulate. Nevertheless the first attempts to operate such a converter at Butte were not successful, as no means had been provided for clearing away obstructions, which formed to some extent in front of the tuyeres. This difficulty was overcome by drilling holes in the outside wall of the air chamber directly opposite the holes in the shell and lining, so that these could be punched

Jan 1, 1934

By Richard S. Smith

THAT management and purchasing have developed a more closely-knit working relationship is evidenced by the fact that more and more companies are appointing the heads of their purchasing departments to the position of vice president. This is concrete and dramatic indication that management is utilizing the knowledge and experience gained in this department and working with it at the policy-making level. When the engineering department is at the planning stage of a project, the purchasing department is being asked to sit in on the preliminary discussions . . .today. One result of this cooperation is that drawings and plans will reflect the current situation on material availability and another is that standardization will be incorporated in new construction and equipment.

Jan 1, 1958

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O'Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By J. Husson, R. Iffly, M. Gondouin

A systematic variation of well deliverability, as reflected from isochronal back-pressure tests performed at regular intervals, has been observed in some gas condensate wells producing at high rates. The same effects have been obtained using a numerical model of gas and condensate flow which takes into account secondary gasoline deposited in the pore space as a result of pressure reduction, and non - Darcy flow of gas in the vicinity of the wells. Matching calculated values with previous test results has been possible, and future predictions have been obtained. An application of this method to the Hassi Er R'Mel gas-condensate field in Algeria is tentatively shown. INTRODUCTION Flow capacity of gas wells is generally derived from an analysis of back-pressure tests. The empirical equation q = C (?p2)n used by Rawlins and Schellhardtl can be derived rigorously assuming that steady-state radial flow of a dry gas of constant viscosity and compressibility is established during each flow period of the well tests. Furthermore, when Darcy's law applies in the entire flow region, the theory predicts that the exponent n is equal to 1. In low-permeability reservoirs, it was soon discovered that the time required to reach a stabilized flow often exceeded the duration of the flow periods normally available for testing wells. Consequently, transient gas flow had to be considered instead of the steady-state assumption previously used. This led to the isochronal testing procedure established by Cullender2 which has largely replaced conventional back-pressure testing. For dry gas fields, this method yields definite values of C and n equivalent to those of the empirical equation. These values should remain constant for each well as long as the permeability of the formation and the characteristics of the gas (viscosity and compressibility) do not change appreciably. This is the case when reservoir pressure remains -close to the original value and when the formation near the wellbore remains free of plugging. Under those conditions, stabilized flow potential curves of gas wells can be established from a single sequence of isochronal flow and shut-in periods. An analysis of a pressure build-up following a longer production period provides additional data on the transmissivity (k h/ u) of the reservoir, and eventually on the 'drainage radius rd of the well, which can be related to the value of C so that future performance of the well can be predicted using the concepts developed by A. Houpeurt.3 At high flow rates, Darcy's law no longer applies in the vicinity of the wellbore, and inertial effects in the high velocity gas flow introduce additional pressure drops. As a consequence, exponent n of the backpressure tests becomes smaller than 1, and a slight curvature of the log-log plot of ?p2 vs q can be predicted when going from very low to high rates of flow (Elenbaas and Katz).5 The effects of variations of viscosity and compressibility with pressure on the radial flow of dry gas in an infinite reservoir were taken into account by Jenkins and Aronofsky.7 Numerical solutions of the transient flow of an ideal gas in finite radial reservoirs were presented by Bruce, Peaceman, Rachford and Rice.8 In the case of gas condensate wells, however, the presence of gasoline in the pore space as soon as reservoir pressure is reduced below the dewpoint pressure further complicates the interpretation of flow tests so that the prediction of stabilized well performance becomes very difficult. Field observation shows that both C and n derived from isochronal tests vary in time, even when reservoir pressure has not changed appreciably. Such a variation cannot be attributed to any change of the gas characteristics, and must result from the effect of a gasoline saturation on the gas flow.

By R. A. Turpin

Bethlehem Steel's Research Department is developing a set of computer programs as mine-planning tools for Bethlehem's coal mines. Several of these computer programs have been completed and have been in routine use by Bethlehem Mines personnel since early 1975. The production scheduling and ventilation planning programs have been installed on an interactive time-sharing computer. The use of time sharing allows mines in remote locations to access these planning tools through standard phone lines and low-cost computer terminals. The capabilities of the interactive production scheduling and ventilation planning programs are briefly described. The advantages of implementing them using time sharing are discussed. A case study illustrates some of the benefits that planning based on the use of these programs has already provided.

Jan 1, 1977

By Walter Larsh

The Ruth orebody, so far developed, is roughly oval in plan, major and minor axes about 1600 ft. (487 m.) and 1200 ft. (365 m.) respectively, average thickness about 120 ft. (36 m.), and with a general dip of about 15° to the northwest. According to the generally accepted theory, the ore is a secondary enrichment of the porphyry due to leaching in situ by meteoric waters. Copper occurs as chalcocite, chalcocite coating pyrite, and a little chalcopyrite. The leached zone, or capping, covering the ore varies in thickness from 110 to 540 ft. (33 to 164 m.), average about 410 ft. (124 m.). The ore is blue gray in color, and the capping, light yellow to brown. Ore was first discovered in quantity in the workings from the Ruth shaft, now caved. Further development work was done by churn drills, and the outline of the orebody, as stated above, determined in this manner. Drilling is still being carried on. The porphyry area is entirely surrounded by sedimentaries, lime-stones and shales; and, in so far as the underground workings have shown, the porphyry' itself, the sedimentaries near the contact, and the country underlying the ore (igneous or sedimentary) is very soft, heavy, and in places swelling ground. All openings have to be carefully and stoutly timbered, and, after once driven, they have to be constantly eased off and repaired. The mine is at present served by two shafts, the Star Pointer, the main working shaft; a vertical, and the Ingersoll, an incline used for waste and material. The two shafts are about 2600 ft. (792 m.) apart, connected on the 500 level; a connection is now being driven on the 600 level. (Dec., 1917. This connection is now completed.) The 300 level, which is finished, and the 400 level which is nearly completed, are accessible only from the Ingersoll and connections with the 500 level.

Jan 1, 1918

By William G. Pariseau

A design procedure for the quantitative estimation of support load requirements in underground mines is presented. The central problem in the design of mine support is one of es¬timating a maximum load that the ground will exert on the support in the coarse of mining. The distribution of stress around mine openings changes as mining progresses. At the time of support installation, the support load is essentially zero. With the passage of time and advance of the face, ground motion loads the support. The finite element method of analysis provides a simple quantitative technique for simulating the effects of mining and face advance on support load requirements. In particular, the maximum support load can be estimated by the proposed design procedure.

Jan 1, 1978

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By R. R. Judd, H. W. Paxton

The rate of dissolution of cementite was studied in three low-carbon materials: a zone-refined Fe-C alloy, an Fe-0.5pct Mn-C alloy, and a commercial low-carbon steel. The materials were spheroidized, ad then held isothermally at temperatures above the Al. The isothermal anneal was interrupted periodically by a water quench and the specimens were analyzed by quantitative metallography for the amount of aus-tenite formed during the anneal. The results of this study were compared with an analytical model for the process, which assumes that carbon diffusion in aus-tenite is the rate-controlling step for the cementite dissolution process. The correlation between the model and the experimental data is excellent for the zone-refined Fe-C alloys; however, the Fe-0.5 pct Mn-C alloys and the commercial steel deviate from the calculated model. This deviation is thought to be a result of manganese segregation between the carbide and the matrix. The rate of nucleation of austenite at carbide interfaces was reduced by the manganese addition and enhanced by the presence of ferrite-ferrite grain boundaries. PREVIOUS investigations of the nucleation and growth of austenite from ferrite-carbide aggregates are not entirely satisfying for at least one of several reasons. The most prevalent of these is a lack of quantitative data. Engineering studies have been run on many steels with little control over important parameters such as composition and initial aggregate structure. The data obtained are valid only for material with identical chemistry and thermal history. A more informative approach to the problem of aus-tenitization would be to determine the mechanism that controls the rate of solution of carbide in austenite and how it is modified by alloying elements. This information could then be used to calculate an austeniti-zation rate for any material, provided its composition and structure are known. The object of the present work is to establish the rate-controlling step for cementite dissolution in Fe-C austenite and to investigate the modification of this rate by small manganese additions. The composition and structure of the material used were carefully controlled and all measurements were designed to allow a quantitative analysis of the kinetic process that controls the austenitization rate. A MODEL FOR DISSOLUTION OF CEMENTITE Cementite dissolution has been analyzed mathematically by a model that approximates the material used in the experiments. This model postulates a regular ar-array of identical cementite spheroids with 4 C( diam, embedded in a grain boundary- free ferrite matrix. The analysis provides a detailed description of the dissolution of one carbide spheroid and a generalization of the solution by summation over all the carbides in the material. The carbides may be isolated by defining identical, space-filling cells of ferrite around them. If the cell dimensions are greater than the diameter of the austenite sphere resulting from complete dissolution of the carbide, and no interaction (through diffusion in ferrite) takes place between cells during the dissolution process, the model need concern only one cell, since the solution in each cell is identical. In the experimental material, the dimensions of the cell, the carbide, and the final austenite sphere are approximately 24, 4, and 8 p, respectively; use of the single cell is therefore justified. The experimental observations are made on the austenite nodules that form around each carbide during the dissolution process. The model concerns the growth of these austenite nodules. The attendant shrinking of the carbide can be obtained from the same analysis by an extension of the calculations. Several a priori assumptions are necessary to make the analysis of the growth problem tractable. They are: 1) carbon diffusion through the austenite nodule is the rate-controlling process; 2) local equilibrium exists at all interfaces, 3) the austenite nucleus that forms on each carbide instantaneously envelops the carbide; 4) during the austenite growth process, the diffusion flux of carbon in ferrite is insignificant; 5) a quasi-steady state exists in the austenite concentration field; that is, at any instant during the dissolution process, the austenite carbon concentration gradient closely approximates that for a steady-state solution; and 6) the effects of capillarity on the dissolution rate of the carbides can be neglected. Referring to Fig. 1, a mass balance at the y-a interface for an infinitesimal boundary movement gives: Where rb is the outer radius of the austenite shell, C1 and C are carbon concentrations at the interface in austenite and ferrite, respectively, see Fig. 2, is the diffusion coefficient of carbon in austenite for the concentration of carbon at the interface, and t is time. The fifth assumption permits the austenite carbon concentration to be approximated by the Laplace solution for the spherical case. Therefore, where C(Y) is the carbon concentration at r, and A and B are constants. Local interfacial equilibrium fixes the boundary conditions for the diffusion problem. They are:

Jan 1, 1969

By C. G. Dunn, W. W. Martin

Various X ray diffraction techniques have been developed for determining orientations of crystals. Transmission and back-reflection Laue methods1,2,3 in particular have been found to be very useful. In many applications, however, a need still exists for a simplification of the details of analysis so that orientations can be determined more rapidly, and operators with little or no training in crystallography can be easily instructed in the necessary procedures. Filling this need in part is a system of analysis that has been in use for several years in the Metals Section of the Laboratory, General Electric Co., Pittsfield, Mass. This method is an extension of the one of Majima and Togino,4 which uses fifty-five indexed standard transmission Lauemams to cover the entire range of crystal orientations. Greater rapidity in determining the orientation of a crystal is achieved by using a slightly larger set of standard Lauegrams and by systematizing the steps followed. This system of analysis in its present form constitutes the subject matter of the present paper. Although the method uses transmission X ray Laue patterns, many of the operations are applicable to the analysis of back-reflection Lauegrams. Very briefly the method is based on the fact that Bragg and azimuthal angles for two or more identified Laue diffraction spots completely determine the orientation of a crystal, and standard Laue photographs of the Majima and Togino type provide a ready means for identifying Laue spots. After a preliminary analysis, which consists of identifying the pattern in terms of one of the standard patterns, a correctly marked Lauegram is selected to carry out the final analysis. From measured Bragg and azimuthal angles, the normals (poles) of the reflecting planes for the selected Laue spots are located on a stereographic projection and the orient.at.ion of the crystal determined (in terms of the positions of cube poles for example) by a few additional operations on a \I1ulff net. The actual procedure followed will be illustrated in detail after a brief treatment or X ray problems connected with orientation determinations and a discussion of useful principles and techniques. X Ray and Plotting Problems RELATIVE ADVANTAGES OF BACK-REFLECTION AND TRANSMISSION LAUE DIFFRACTION METHODS In the back-reflection Laue method it is easy to make a direct measurement of the tilt of a zone of Laue spots. Specimen thickness also is generally no problem. In the case of thin specimens, however, the time of exposure is less for the transmission Laue method. For example, with silicon ferrite this advantage holds up to a thickness of 0.6 mm if tungsten radiation at 40 kv peak voltage is used. Furthermore, the transmission photograph represents the entire thickness of the crystal whereas the back-reflection picture represents only a surface layer (a thickness of less than 0.05 mm for silicon ferrite), the deeper layers supplying a negligible amount to the diffraction pattern. If a crystal is distorted, the transmission Laue pattern gives more information particularly with regard to the orientation of the crystal and the overall amount of spread in orientation. Finally a 3 1/4 X 4 in. film suffices for transmission photograms; a 4 X 5 in. or 5 X 7 in. film with a central hole is needed for back-reflection patterns Not only is the manipulation of film easier because of the size of film, but

Jan 1, 1950

By H. A. Davies

DURING a current program of research on the structure and properties of liquid sodium alloys, the need arose for information on the solubilities as a function of temperature of several B subgroup metals in liquid sodium. In the absence of reliable information in the literature for several of these systems, par- ticularly at temperatures in the range 100° to 300°C, an apparatus was constructed to determine solubilities by a direct melt-sampling technique, followed by wet-chemical analysis for both sodium and the solute metal. The details of the technique have been described previously.' The solubility of indium in liquid sodium was determined at eight temperatures in the range 100° to 270°C. The solubility as a function of temperature is shown on Fig. 1; this represents the liquidus line over this composition range. A cooling curve was plotted after the completion of the sampling and an arrest was observed at 94.9°C which must be interpreted as being the result of a eutectic reaction. By extrapolation of the liquidus to this temperature, the eutectic composition was estimated to be about 0.25 at. pct In. The present estimate of the eutectic temperature and composition are in good agreement with the values of 96.0° to 96.2°C and between 0.28 and 0.45 at. pct In, respectively, which were reported by Heycock and Neville.2 However, no further information on the liquidus of this system at the sodium-rich end could be found in the literature for comparison. One compound: NaIn, has been reported in this sys-

Jan 1, 1968

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

By R. L. Templin

THE increasing use of aluminum and its alloys in commercial fields has demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure aluminum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. COMPARISON OF CUTTING TOOLS Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30° to 50°, making the total angle of the cutting edge of the tool from 35° to 55°. A side

Jan 1, 1928

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side