Search Documents

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep underground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county provides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest competitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of gas-solid reactions with special attention given to the hydrogen reduction oj dense spheres of hematite. This reduction process must pvoceed through a sequence of transport and chemical .reaction steps acting in series. Under typical experimental conditions, none oj the individual transport and reaction resistances may be neglected in the development of a physically significant model. A linear vate of thickening oj the product layer, usually taken as evidence of interface-controlled .reuction, may be observed even though transport resistances play a dominant role in the over-all kinetics. The temperature and pressure dependencies of all terms have been carefully evaluated in order to .make fill use oj arailable expe-inzental data in evaluation oj the model. FOR obvious technological reasons, the kinetics of reduction of iron oxides has become the subject of intensive experimental and theoretical investigation during recent years. Continuing efforts to construct mathematical models to describe the kinetics of reaction between a gas stream and a granular bed of solid particles have demonstrated the necessity of a thorough understanding of the reaction kinetics of a single particle within the system as a prerequisite to the construction of physically significant models of complex, reacting systems. This paper presents a critical examination of the transport and chemical-reaction processes involved in single-particle oxide reduction and develops the mathematical expressions necessary to evaluate their importance. Comparison of theoretical predictions with experimental results contributes important new understanding of the complex nature of this process. The reduction process has been studied under a wide range of experimental variables, and it is not surprising that apparent conflicts in observation and interpretation appear in the literature. The interested reader is referred to the reviews of Themelis and auvin"? and Manning and philbrook3 for a description of much of this work. The course of reaction commonly has been followed by measuring the oxygen weight loss from the particle as a function of time. A number of authors have suc- cessfully correlated their data in terms of a model which assumes that the reduction process is controlled by the rate of reaction at a single, sharply defined, advancing interface. According to this model, the interface will advance linearly with time. A mathematical model for gaseous reduction in a packed bed developed by the present authors in an earlier paper4 recognized that reduction must proceed through the series hematite (Fe203), magnetite (Fe30,), wiistite (Fe,O), and finally metallic iron. The reduction scheme permitted a stepwise topochemical reduction of the individual particles to metal or to the lowest oxide thermodynamically possible for the local gas composition in the bed. The limiting situations of theoretically dense and very porous oxide structures were considered. On the basis of available experimental evidence, the simplifying assumption was made in each case that all product layers would thicken linearly with time. A generalized single-particle model has now been developed to determine the significance of transport resistances in the product layers and in the gas film surrounding the particle. The analysis shows that the interplay of transport and chemical resistances is such that an apparently linearly advancing interface may be observed despite the fact that the reaction may be under significant transport control. Attention thus far has been focused on the development of a model for the topochemical behavior of dense spheres of hematite in atmospheres capable of reducing them completely to metal. The formation of successive product layers of iron, Fe,O, and Fe304 is assumed to follow the mechanism originally described by dstrijm.' All oxygen removal from the core occurs at the iron/Fe,O interface, intermediate oxide layers being propagated by sol id-state diffusion without change in the oxygen density of the core. Since fractional reduction is operationally defined in terms of oxygen weight loss, the kinetics of the over-all reduction of FeZ03 to iron is properly studied in terms of the gas-solid reaction occurring at the iron-wiistite interface. The fractional reduction of a partially reduced oxide sphere is given by: here refers to the radial position of the iron/Fe,O interface. This model is not universally applicable because, as explained in the earlier paper,4 a consideration of porous particles or of dense particles in atmospheres not capable of reducing wiistite must allow for the possibility of gaseous reduction at interfaces other than the one between iron and Fe,O. However, evidence that certain hematite specimens actually do follow the dense-pellet mechanism developed here is provided by the data of cewan' and of Bogdandy and

Jan 1, 1967

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,' appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.' For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,' polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By D. A. Woodford

A number of observations have now been reported where the steady-state creep rate is apparently linearly dependent on the applied stress at high temperature and low stresses. This results in a creep rate greater than that predicted by extrapolation of high-stress data and has obvious practical implications. However, some of these observations are open to question. For example, the analysis by Harris and Partridge17 of the data of Greenfield et a1.18 was dependent on strain rates which, according to the original authors, were too low to be measured. Dr. Bernstein appears to have demonstrated a linear stress dependence at low stresses in two zirconium alloys. There are, however, a number of discrepancies in his treatment of the data and the subsequent theoretical analysis which require clarification. 1) It is incorrectly stated that steady-state conditions are revealed by a slope of unity on a plot of log i vs log (time). This objection is trivial if the author meant to say a slope of zero, although it is unclear how subsequent extrapolation was made to determine the steady-state creep rates at low stresses for the zircaloy-2. If the plot used was actually log c vs log (time), it is unlikely that a slope of unity would represent a constant creep rate. A plot of log (c - co) vs log (time), where c0 is the extrapolated intercept sf the steady-state creep rate on the strain axis, would have a slope of unity during steady-state creep. However, eo cannot be determined unless is is already known. 2) The author chooses to interpret his results based on the equation: where A, and B, are structure-sensitive parameters, Ql and Q, are the activation energies for the particular creep process, and n describes the sensitivity of the creep rate on stress. The first term represents a slip creep process and the second a diffusion creep process. However, it is stated later that "two distinct processes acting in parallel are involved". Eq. [I] surely represents two processes in series since each reacts to the total applied stress and t, is the sum of the individual creep rates. If the processes are acting in parallel, then the effective stress in each would be less than the applied stress. The component stresses would be given by sl + s2 = a but it is not clear how the magnitude of either, or the corresponding stress exponent, could be determined.

Jan 1, 1969

By S. Floreen, H. W. Hayden

The effects of additions of iridium, rhodium, ruthenium, and platinum on the mechanical properties of Fe-C alloys were determined. Each alloying element significantly improved the toughness. The results support the general correlation that substitutional alloying elements that stabilize austenite are beneficial to toughness, but the reason for this improvement is not obvious at this time. The effects of substitutional alloying elements on the toughness of steel has long been a subject of both practical and theoretical interest. Despite the obvious importance of this subject, there has been little progress toward understanding the mechanisms by which alloying elements influence the fracture behavior. In some cases the deleterious effects of alloying elements have been shown to be due to mechanisms such as embrit-tlement of prior austenite grain boundaries or inhibition of cross slip in the ferrite lattice. In other cases, however, the reasons for the change in properties are not clear. This is particularly true for elements, such as nickel, that improve the resistance to brittle fracture. Several investigators'-3 have pointed out that there is a correlation between an alloying element's phase diagram with iron and its effect on toughness. Those substitutional alloying elements that stabilize austenite generally are beneficial to toughness, while ferrite-stabilizing elements generally are detrimental to toughness. The word "generally" should be emphasized, because exceptions to this rule can be found. Nevertheless, this correlation does offer a starting point at which to try to understand the effects of alloying elements on toughness. Thus far only two austenite-stabilizing elements, manganese and nickel, have been considered. In order to test the validity of this correlation several other austenite-stabilizing elements were evaluated. The noble metals, iridium, rhodium, ruthenium, and platinum, have binary phase diagrams with iron similar to the Fe-Ni and Fe-Mn diagrams. That is, each element expands the austenite field, and also higher concentrations of each element produce martensitic transformations at low temperatures. Presumably then, each of these elements should improve the toughness of steel. The present study was conducted to determine if this were so. EXPERIMENTAL PROCEDURE The alloys were made as l-lb air-induction melts using electrolytic iron and commercially pure noble metals. Each heat was initially deoxidized by a carbon boil, and further carbon was added to attempt to produce a 0.05 wt pct C content in each alloy. Before pouring, a final refining addition of 0.2 wt pct A1 and 0.1 wt pct Ti was made to each heat. The alloys were cast in a copper mold to produce ingots approximately 1 in. in diam and 5 in. long. The chemical compositions of the alloys tested are given in Table I. The residual nitrogen, aluminum, and titanium contents were all relatively constant at 0.003, 0.03, and 0.02 pct, respectively. The carbon

Jan 1, 1968

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925

By J. O. Mack, J. B. Russell

In recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. Table i.—Composition Ranges Prescribed for a Commercial Substitute Solder Element Per Cent Tin............................ 18.0-20.0 Bismuth (maximum)a............ 0. 80 Silver.......................... O. 10-1. 25 Bismuth plus silver (minimum).... 0. 85 Antimony (maximum)............ o. 50 copper (maximum),,,,,,,,..,,,, 0. I3 Other elements, each (maximum)6 0.03 Lead........................... balance a When silver is present in excess of I per cent, the Bi content shall be 0.50 per cent or over. b Total not to exceed 0.10 per cent. The Purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing 18 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic I5-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wet-tability, that will enable it to be used on the metals in common use. Basic Considerations The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat. If a soldering iron is used, it must not only

Jan 1, 1945

By R. A. Vandermeer

It is usually assumed that the rate-determining step in the migration of a grain boundary involves the thermally activated transfer of single atoms across the interface. Chemical reaction rate theory then gives a migration rate which is proportional to the driving force when this is small compared to kT.1 In their recrystallization studies on aluminum, Gordon and vandermeer2 obtained data which was capable of providing the first experimental test of this proportionality. They correlated stored energy (driving force) release measurements determined calorimetrically with fraction recrystal-lized kinetic (growth rate) data acquired metallo-graphically at a temperature where a significant amount of recovery takes place concurrently with recrystallization. Within experimental error, the results of Gordon and Vandermeer confirmed experimentally, at least over a limited range, the linear dependence of boundary migration (growth) rate on driving force in accordance with theory. In obtaining these results, however, an incorrect, implicit assumption was made in relating the average instantaneous growth rate of the recrystallized grains to the measured fraction recrystallized kinetic data. The purpose of this present note is to point out and correct this assumption. An alternate approach, whereby a more proper average growth rate can be calculated from the recrystallization kinetic data, is presented. The earlier data, reevaluated in terms of this new approach, show the same general trend as before so that the original conclusion of Gordon and vandermeer2 is still valid. As was shown in a detailed study3 of the geometrical features of recrystallization in aluminum, the colonies of recrystallized grains can be regarded as uniform cylinders embedded in a three-dimensional matrix, the number of such colonies being constant. Thus during the early stages of recrystallization the volume fraction recrystallized, Xv, can be written as Xv=ynvlr2 [l] where y is a shape factor and i and r are defined as the average length and radius of a recrystallized colony and are spatial averages over the specimen. -nv, is the number of such colonies in a unit of volume. The erroneous assumption made in the earlier paper2 was that r in Eq. [I] could be replaced by

Jan 1, 1965

By Howard A. Smith

Of late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloy1-9† although two investigations have been made on copper alloys10*". That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-for~chung'13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At suberitical temperatures above Ar" (temperature of martensite formation) where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain' find that different sorts of atoms in solid solution in gamma iron affect the length of this " prereaction" period differently, manganese probably being the most effective in lengthening it. It is very difficult to believe that nothing occurs within these "prereaction" regions, for if this were so there is no reason why any reaction at all should be observed. In the light of experimental facts and theoretical considerations it is certainly

Jan 1, 1935

By Howard A. Smith

Of late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloy1-9† although two investigations have been made on copper alloys10*". That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-for~chung'13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At suberitical temperatures above Ar" (temperature of martensite formation) where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain' find that different sorts of atoms in solid solution in gamma iron affect the length of this " prereaction" period differently, manganese probably being the most effective in lengthening it. It is very difficult to believe that nothing occurs within these "prereaction" regions, for if this were so there is no reason why any reaction at all should be observed. In the light of experimental facts and theoretical considerations it is certainly

Jan 1, 1935

BEING at the crossroads, metaphorically speaking, seldom has the advantages of the literal sense of the words. One seldom has precise knowledge of the existence of the metaphorical crossroads or forks in the road of life. A case in point is the Committee on Education of the Engineers' Council for Professional Development, which for twenty years has been accrediting the engineering curricula in the educational institutions of the United States. The committee is now at odds with itself and with the National Council of State Boards of Engineering Examiners over the accrediting of courses which in the opinion of many engineers are not strictly speaking engineering curricula at all. Such courses include: fire protection engineering, crystal engineering, nuclear engineering, and geological engineering. The crossroads might be placed arbitrarily somewhere between 1936 and 1938 when the committee first started accrediting curricula and included the first course in industrial engineering. Purists might argue that the committee first wandered from the straight and narrow when it recognized subdivision of engineering into the major branches of mining, metallurgical, civil, mechanical, electrical, and chemical engineering. Accrediting is certainly an important function because it provides a standard for engineering education and it should be done on a national basis by an unbiased group like the Education Committee of ECPD. Students, educational institutions, and industry derive great benefit from proper standards. The autonomous State Boards of Engineering Examiners have long accepted ECPD accreditation as evidence of the required academic training of engineers aspiring to licensing. But the State Boards today question the wisdom of applying the name engineer to graduates of some of the so-called fringe curricula. The Education Committee, having gone so far in accrediting some of them, has numerous applications pending for accreditation of similar curricula and even new courses never before accredited. Arguments against recognizing highly specialized engineering curricula are numerous. The Salary Stabilization Board has disallowed industrial engineering from classification as engineering for its purposes. A graduate of a specialized course in geological engineering at a school in the Southwest slanted heavily for practice in the petroleum industry might not be interchangeable with a graduate of a similarly designated curricula at one of the institutions in the North Central states where the emphasis might be on metallic. mineral deposits. Industry in general should not expect the universities to supply a degree in each of the specialized engineering classifications it might set up for purposes of salary or job designation. Having gone so far, it is easy to understand the difficulty of the Education Committee. ECPD might well call a moratorium for the purpose of taking stock of its position. If the present trend is allowed to continue, it is apparent that an engineering institution could be subdivided into a multiplicity of departments teaching specialized curricula resulting in a subordination of the basic concepts of engineering. Although the parallel of the medical profession is trite, it should be pointed out that degrees in medicine are not labelled by the numerous specialities practiced by doctors. For practical purposes the ECPD would do well to accept the fact that the crossroads have been overreached "and protect the engineering profession by coming up with minimum standards for an engineering curriculum.

Jan 1, 1952

By C. A. Stetefeldt

The hacienda Sauceda is one of the largest and finest haciendas in the vicinity of the City of Zacatecas, Mexico, and is said to reduce ores by the Patio process more cheaply than any other establishment. It receives its supply of ore from the San Acacio mine. This mine has been for some time, like most of the Zacatecas mines, out of bonanza, and yields, at present, ore of rather low grade. The silver occurs principally as silver-glance, ruby-silver and native silver, associated with pyrites of iron and copper, and some galena and zinc-blende, in a gangue of pure quartz, which takes the form of amythyst whenever the ore is of high grade. All the ore, as it comes from the mine, is broken by hand into small pieces, and sorted before it is delivered to the hacienda. Here it is first crushed dry in Chili mills, and then ground wet in arrastras to an impalpable powder. The sulphurets not decomposed in the patio process are separated in the settlers from the tailings and concentrated by hand. By roasting them in a reverberatory furnace with carbonate copperores, "magistral" is obtained. All machinery is driven by mulepower.

Jan 1, 1885

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947