Search Documents

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

LIMA, PERU Established May, 1952 (Official year begins in June) Luncheon meetings third Wednesday monthly Ernesto A Baertl, Chairman Arthur C Hall, Chairman-Elect Raymond R Beard, First Vice-Chairman Edgardo Portaro, Second Vice-Chairman Walter E King, Secretary-Treasurer Av Santa Cruz 331 San Isidro, Lima, Peru Alberto E Brazzini, Asst Treasurer Daniel M Rodriguez, Asst Secretary, '58, Section Delegate '58, Alternate Section Delegate

Jan 1, 1956

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By B. Haimson, C. Fairhurst

One of the main functions of rock mechanics research has been to find ways of determining in-situ stresses. Many methods have been suggested, the most significant ones calling for measurements inside bore- holes. These methods usually employ some instrumentation for the purpose of measuring hole deformation. Several years ago, a new method was suggested by Scheidegger,l based on previous work by Hubbert and Willis.2 It was the method of "hydraulic fracturing," which had been introduced by the oil industry in 1948 for the purpose of oil-well production stimulation. Basically, hydraulic fracturing consists of sealing off a section of a borehole, pumping in a fluid, and pressurizing it until fracture occurs. If pumping is continued vigorously, the fracture is opened up and extended. In an oil field, such an artificial fracture increases the overall permeability of the formation and usually enhances production. During the entire operation, the variation of pressure with time is ordinarily recorded. Hubbert,2 Scheidegger,1 Kehle,3 and others have shown that the recorded pressures can be theoretically related to the magnitudes of the principal in-situ stresses; the orientation of the fracture can often be used to determine the direction of the principal stresses. The advantage of hydraulic fracturing over the present in-situ stress determination methods is simplicity: no sophisticated instrumentation is required inside the borehole; hence, the stresses can be measured at any depth. Moreover, if the formation is impermeable to the fracturing fluid, no elastic constants of the rock are required in calculating the stresses, a

Jan 1, 1970

Between two and three years ago, in response to an unmistakable and insistent demand, the four Founder Societies appointed Committees on "Aims and Organization," or on "Development," charged with reporting on the internal organization and the external (non-professional) ac-tivities of the engineers societies and to advise as to coöperations and coordination. Each of these committees formulated a report, recognizing that effi-ciency in external activities could only be attained by intimate coopera-tion between the four Societies. As a consequence, each of the Founder Societies was requested to appoint members of a Joint Conference Committee, charged with discussing the situation and evolving if possible a plan of cooperation in external activities which would coordinate not only the efforts of the four Founder Societies but also other national technical and scientific societies, as well as local engineering and profes-sional associations, groups or clubs. The Joint Conference Committee entered on its task with enthusiasm, and after great labor evolved the outline and many of the details of plan for engineering cooperation in public and inter-society activities. This report has now been submitted to the Boards of the Four Founder Societies, and has been ordered printed by our Board for the information of our members.

Jan 12, 1919

By H. B. FERNALD

THE first year to which the Revenue Act of 1936 has applied is now passed. It is appropriate to try to give some calm thought to the plan of Federal income taxation as now imposed and what it will mean to the business and industry of the country if this plan of taxation is continued unchanged. Whether or not we like to pay these taxes is beside the point. Taxes are high and may be expected to be high for many years. The important question is whether the taxes to be imposed will destroy or injure business enterprise and development, and, in so doing, lower the standards of employment, living, comfort, and welfare of our people. The power to tax is the power to destroy. That destruction may come suddenly as a cyclone, or slowly as dry rot. What, if any, features are there in the present plan of Federal income taxation that have these destructive tendencies? A few of the points follow that seem to call for consideration.

Jan 1, 1937

By A. J. Lanza

THE prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would- markedly increase their liability to accident. The number of men working underground in mines in this country whose physical, condition totally unfits them for such work presents-a situation that should not be allowed to continue, and which I believe is 'not equalled in any other, industry in the country. There is but one way to secure men who come up to the required standard, . and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to he said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a

Jan 2, 1919

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By R. L. Slobod, H. A. Blum

A semiquantitative method for measuring the wettability of reservoir rocks has been developed. These data are needed for reservoir analysis and for interpretation of laboratory displacement studies. The wettability of a core sample is measured by the contact angle for the system oil-water-solid. These contact angles are calculated from the displacement pressure (threshold pressure) obtained by use of the centrifuge, using first oil-water and second air-oil in the same core sample. This method is based on the assumption that the air-oil and oil-water interfaces occupy similar positions in the porous medium when desaturation of the wetting phase is initiated. The assumption is also made that the Contact angle for the air-oil-solid system which is close to zero in value does not change appreciably even when the contact angle for the oil-water-solid system experiences marked changes. "Apparent contact angles'' for five different solids ranging from 31" to 82" have been determined, and changes irr the "apparent contact angle" of a given sample with laboratory use from 33" to 53' {lave been observed. INTRODUCTION Reservoir rocks vary in their wettability, 1,2,3,4 some being preferentially water wet while other are apparently preferentially oil wet. The degree of wettability, in theory, is measured quantitatively by the contact angle for the system solid-oil-water, hut in 1)practice this quantity is extremely difficult to determine." The need for obtaining some measure of this quantity has become obvious in recent years as a result of both laboratory. and field observations. Several reservoir.: such as the Bradford Sand in Pennsylvania and the Wilcox' at Oklahoma City are reported to be oil wet. If these report:: correctly reflect the true nature of the surface of the rock in the ground, then these reservoirs probably will not perform as predicted on the basis of a water wet rock. In the laboratory many core samples have been Observed to be oil wet. These samples, while perhaps not correctly representing the reservoir, have markedly different properties from water wet rock. The location of the phases is different (oil is in contact with rock instead of water), and other quantities such as the connate water, the capillary pressure curve; residual oil. relative permeabilities. and the recovery of oil by water flooding are markedly affected by the value of the contact -4 A further complication observed in the laboratory is the chang-ing of the wettability of a rock specimen with use. such changes mean that repeat runs on the same core are not the duplicate tests desired, but represent new experiments on a more oil wet material. The changes in surface characteristics are sometimes so rapid that by the time an experiment requiring several days is completed, the results may not be representative of the core as originally described, The, rock material itself (Silica. carbonates. etc.), whell Clean and uncontaminated, is water wet. There seems b( : little evidence of the presence of oil wet minerals such as heavy metal sulfides. The oil wetness of reservoir samples, therefore, is believed to be caused by the accumulation of an adsorbed film in which the polar group of a large organic. molecule is adsorbed on the surface leaving the organic or hydrocarbon part of the molecule projecting out from the solid. Such a surface is much more readily wet 17" oil than by water. These considerations indicate the need for a method which will provide some measure of tile wettalbility (Contact(angle if possible) for reservoir rock ..samples) The method should be capable of (1.1 distinguishing between tile wettalility of dif. ferent formation,.. (2) detecting (change. ill wettalbility of a core with use. and (3) measuring the changes in Wettability which may be accomplished with cleaning operations. such as the use of sodium silicate for increasing water wrettalbility." A preliminary report on such a method is preseted below. not with the idea that this procedure alone will Solve the wettabil-ity problem. but rather that it may provide encouragement to

Jan 1, 1952

By N. S. Kenny, A. A. Burr

THE purpose of this note is to present evidence that vacancies, which have been produced by quenching from a high temperature, alter the rate of strain-hardening of an hep single crystal. The majority of investigations of the effects of quenched-in vacancies on the yield stress of metals have been made using fee samples in the form of thin wires. However, there is an inherent disadvantage in using such wires to study the effects of vacancies on the rate of strain-hardening of metals because fee wires begin stage II slip either immediately upon yielding or very shortly thereafter. When stage II slip occurs, very rapid strain hardening also occurs, masking the effects of vacancies on the rate of hardening. In this investigation single crystals of magnesium hep were studied since magnesium has only one slip plane at low temperatures and has, therefore, an extensive easy glide region. In addition, the effect of both static and dynamic recovery on the rate of hardening were eliminated by testing in liquid nitrogen. Both forms of recovery occur in hep metals by dislocation climb, which is a diffusion controlled mechanism and is negligible at liquid nitrogen temperatures. Finally, the dependence of the strain-hardening rate on the crystal orientation was eliminated by using the equations of Schmid and Boas.' Variations in the strain-hardening rate could, therefore, be attributed to the presence of vacancies. Single crystals in the form of rods approximately 5 mm in diam and 6 cm long were grown by a modified Bridgman technique from commercial high-purity magnesium (99.97 pet) supplied by the Dow Chemical

Jan 1, 1962

CHARLES F. WILLIS,* Bisbee, Ariz.-(written discussion?).-The consensus of the discussion of the paper of Dr. Lanza indicates that the physical examination, while it is probably a good thing, is fought by the workingman, and that, because of this fact, it has been proved unsuccessful. The physical examination standing alone is worth but little, and could easily be made a subject both of ridicule and dissension unless the company having such examination shows its own good faith in promoting a thoroughly better health program. It is easily seen why a workman would resent his employer expecting him to be physically fit, if at the same time the employer provides un-healthful, unsanitary, working conditions, or if the town in which the employees are expected to live is dirty and unkempt. One mocks the other. The employer cannot say, "You must remain healthy so that I can get by with unhealthy conditions." But if working- conditions are as good as can be obtained to keep men well, the employer can ask his men to be in a healthy condition. A State examination and standard would have many difficulties, owing to the fact that a man would pass or would not pass the standard set, thus eliminating the discretion on the part of the employer in placing men whose physical condition might well permit working in one place and not another. Any physical examination that is run for the purpose of eliminating the physically unfit is unjust, both to the worker and to the nation as a whole; a State examination would make a distinct dividing line, whereas examination by the employer is conducted with a vision of the positions available. The workman's opposition to the physical examination comes from the fact that he has been taught to believe that it is an interference in his personal affairs, that he can be clean or dirty as he chooses, that he can he healthy or unhealthy, and that it is nobody's business but his own. The war has taught us, however, that the individual is no longer the unit and that all such propositions must be based on the greatest good for the greatest number.

Jan 6, 1919

By A. J. Shaler, H. Udin, J. Wulff

In the study of the sintering of meta powders, we have come to the conclusion in this laboratory that further progress requires a more basic understanding of the operating mechanisms. This is emphasized in detail by Shaler. He has shown that a knowledge of the exact value of the surface tension is imperative for a solution of the kinetics of sintering. This force plays a principal role in causing the density of compacts to increase.2 Furthermore, a knowledge of the surface tension of solids is also applicable to other aspects of physical metallurgy. C. S. Smith3 points out the relation between surface and interfacial tension and their function in determining the microstructure and resulting properties of polycrystal-line and polyphase alloys. This paper describes one group of results of an experimental program designed for the study of the surface tension in solid metals. As a by-product of this work, considerable information has been obtained on the rate and nature of the flow of a metal at temperatures approaching the melting point and under extremely low stresses, a field of mechanical behavior heretofore scarcely touched by metallurgists. The importance of this additional information to students of powder metallurgy need not be stressed. Theoretical Considerations Interfacial tension arises from the condition that an excess of energy exists at the interface between two phases. Gibbs proves that this energy is a partial function of the interfacial area; thus: ?F/?s = ? where ?F/?s is the rate of change of free energy of the system with changing surface area, at constant temperature, pressure and composition, and ? is the interfacial tension, or interfacial free energy per unit area. If one of the phases is the pure liquid or solid, and the other the vapor of the substance, ? may properly be termed "surface tension," and is a characteristic of the solid or liquid. The attempt of a body to lower its free energy by decreasing its surface gives rise to a force in the surface which is numerically equal in terms of unit length to the free energy per unit area of the surface. Thus ? may be expressed either in erg-cm-² or in dyne-cm-1. Similarly, surface tension may be determined either by a thermo-dynamic measurement of the surface energy or by a mechanical measurement of the surface force. We have chosen the latter approach. Tammann and Boehme4 determined the surface tension of gold by measuring the amount of shrinkage or extension of thin weighted foil at various temperatures and interpolating to zero strain. The method is of questionable accuracy because of the tendency of foil to form minute tears when heated under tension. Their assumption of F = 2W?, where W is the width of the foil, is unsound, as the foil can decrease its surface area by transverse as well as by longitudinal shrinkage. Although their experimentation was meticulous, the paper does not include details of the sample configuration required for recalculating ? on a correct basis, even if such a calculation were possible. In the experimental procedure chosen here, a series of small weights of increasing magnitude are suspended from a series of line copper wires of uniform cross-section. This array is brought to a temperature at which creep is appreciable under extremely small stress. If the weight overbalances the contracting force of surface tension, the wire stretches; otherwise, it shrinks. The magnitude of the strain is determined by the amount of unbalance, so a plot of strain vs. load should cross the zero strain axis at w = F?. If balance is visualized as a thermodynamic equilibrium, the critical load is readily calculated. At constant temperature, an infinitesimal change in surface energy should be equal to the work done on or by the weight: ds = wdl [A] For a cylinder, s = 2pr2 + 2prl [2] If the volume remains constant, r = vV/pl [31 s = 2vpl+2V/l [4] ds = vpv/l - 2V/l²) dl [5] Substituting [5] into [I] gives for the equilibrium load, w = ?(z/rV- 2V/12) [6] and, again expressing V in terms of r and l, w = pr?(1 - 2r/l [7] Here the end-effect term, 2r/l, is neglected for thin wires in subsequent work. Eq 7 can be confirmed by means of a stress analysis. If the x-axis is chosen along the wire, then the stress is 2pr? - w pr² pr2 [8] A cylinder of diameter dis equivalent to a sphere of radius r, insofar as radial surface tension effects are concerned.³ Thus xv = 2?/d = ?/r = sz [9] For the case of zero strain in the x direction, the strain will also be zero in the y and z directions. Since the wire is under hydrostatic stress, Eq 8 and 9 are

Jan 1, 1950

By M. K. Barnett

Engineering research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency—i.e., the attain- ment of the maximum amount of reliable, useful information relating to the influence of, the factors on the property of the product or characteristic of the process, for the least expense—is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modern methods for the analysis and evaluation of experimental data. The Present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1948

By M. K. Barnett

Engineering research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency—i.e., the attain- ment of the maximum amount of reliable, useful information relating to the influence of, the factors on the property of the product or characteristic of the process, for the least expense—is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modern methods for the analysis and evaluation of experimental data. The Present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1948

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By G. A. Beske, P. Hilsch, J. Wulff

The effects of the growth precipitates on the su-perconduching properties of an Al- 15 al. pel Zu alloy have been studied using magneization, transition lem-perature, and residual resistivity measurements. Aging at 230C for 1/2 to 11 he produces an increase in Hfp, Ike field of first penetration, and tut increase in trapped flux. The upper critical field, Hc2 remains constant for such aging tunes. Aging at 200°C produces a decrease in Hfp and an increase in trapped flux. The transition temperature remains constant at Tc - 1.227° ± 0.02°K for aging at 220°C for tims of from 1/2 to 10 hr, and for aging at 200°C it remains constant at Tc. = 1.18° i 0.02°K for times from 1/2 hv to 26 hr. The observed behavior indicates that the superconducting matrix when aged at 220°C behaves tike a type U su-perconducior, but when aged at 200°C behares like a type I superconductor. The magnetization changes after aging can be attributed to the growth and clutnge in distribution of the precipitate in a matrix of fixed composition. IT has been realized for some time that the superconducting properties of alloys are highly structure-sensitive. This is evident in the work of Mould and Mapother1 who examined the properties of an aluminum alloy. Precipitation effects have also been briefly mentioned in other studies.2-4 Bonnin and coworkers5 have observed a sharp inc rease in trapped flux in an A1-Mg alloy when the residual resistivity reaches a value that indicates it is a type II superconductor. Recently Blanc, Goodman, and Nemoz5p have reported on precipitation effects in A1-Ag alloys. Detailed studies of precipitation in Pb-Sn and Pb-Cd alloys made by Livingston6 serve to show that the upper critical fields are enhanced by quenched-in solute. Furthermore. at various stages in the precipitation process? the upper critical field is determined largely by the remanent solute. The observed magnetic hysteresis and trapped flux in such alloys result from the interaction between precipitate and the flux filaments in the mixed state. The flux trapping appears to depend largely on the precipitate distribution and is greater if the superconductor is type II than if it is type I. To examine the effect of precipitation in another alloy system, particularly one in which the composition of the superconducting phase does not change significantly during the course of precipitation, the Al-Zn system seems interesting, especially in view of the transition temperature and resistivity studies of Chiou and seraphim.' Furthermore, the recent detailed electron-microscope studies of an Al-Zn alloy by Richards and Garwood8 provide a guide for relating superconducting properties to changes in structure. For these reasons, magnetization, transition temperature, and residual resistivity measurements for varying times of heat treatment at two temperatures were made with a -15 at. pct Al-Zn alloy. The results are reported in this paper. I) EXPERIMENTAL The alloy used was prepared by Cominco Products Inc. from 99.9999 A1 and 99.999 Zn. It was chill-cast, swaged, and drawn to 0.125-in.-diam rod. The analyzed composition was 15.6 at. pct Zn (31.1 wt pct). A jeweler's saw was used to cut the 0.125-in.-diam rod into the 0.875-in. lengths needed for magnetization measurements. The ends of the cylinders were slightly beveled to remove the sharp edges. A portion of the original 0.125-in.-diam rod was drawn into 0.010-in.-diam wire and used for transition temperature measurements. Specimens were suspended from wires within a vertical furnace during heat treatment. All were homogenized at 500°C for a minimum of 3 days and subsequently solutionized for times in excess of 6 hr. The solutionizing temperature was held constant to +3°C. Individual specimens were homogenized, quenched, and aged several times and no effects indicating loss of zinc were noted. The suspended specimens were quenched by cutting the wires and allowing the specimens to fall into a silicone oil bath held at the aging temperature. They were then isothermally transforked by aging in the same bath used for quenching. After aging for the required time (approximately 10 min aging was necessary before the upper critical field reached a fixed value), they were briefly (1 to 2 sec) dipped into an acetone bath at room temperature to remove adherent oil and then immediately transferred to liquid nitrogen where they remained until inserted into the helium bath (usually within an hour). The temperature of the aging bath was held constant to +3°C for longer aging times. The cryostat used for the measurement of superconducting properties consisted of outer and inner dewars for liquid nitrogen and liquid helium, Stokes 6-in. booster diffusion pump and Stokes Model 212 mechanical pump, temperature controller to measure and control the temperature of the helium bath, and a superconducting solenoid with inserted search coils to provide the magnetic field and measure the magnetic moment of the specimens. A schematic diagram of the cryostat is shown in Fig. 1. An ultimate temperature of 0.85°K was reached with this apparatus. The temperature controller used is similar to the one described by Blake and chase.' A 0.5 pct Allen-Bradley carbon resistor and a nichronle heater (200

Jan 1, 1968

By R. L. Wiegel

The generation of operating information for mineral beneficiation processes has become more sophisticated as a result of the use of improved laboratory analytical techniques, some of which provide multiple component assays, as well as the introduction and gradual industrial acceptance of process sensors for the measurement of flow, density, size, and chemical composition. In general, however, the mineral processing engineer's ability to tie together this wealth of information has not kept pace with these developments. In fact, in almost all existing plants, the metallurgical inflow-output balance, wed to indicate current process performance, is still being calculated from only a small portion of the information routinely available. There is substantial activity in the development of techniques for using all available process information to significantly improve the reliability of the metallurgical balance. While the use of these improved techniques does require access to computing facilities and a slight change in perspective on the part of the mineral processing engineer regarding the inviolability of process information, there are numerous practical benefits to be derived from their application. In addition to summarizing some of the concepts basic to these techniques, this paper describes the experience of the author in applying one of these advanced metallurgical balance techniques to a variety of pilot plant and commercial plant flowsheets during the past eight years.

Jan 1, 1983

By J. J. Kantner

CREEP investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that applica-tion of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and struc-tural character of the solid metal.

Jan 1, 1937

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969