Search Documents

By C. T. Cox

The title of this short paper necessarily implies that friction articles comprise a distinct and unique field and are different from the other metal-powder articles, such as bearings, electrical contacts, and magnets. However, this distinction is rather hard to define in that it is really one of degree and not Of kind. It would appear that the main distinction is that friction are are articles of rather large pressing area. In other words, they are articles in which the area Of the mold in which the metal powder is pressed is relatively large. Other articles made from meta1 powders are generally of rather small area, usually a few square inches, while in friction articles the area ranges up to several hundred square inches. The satisfactory production of meta1-powder friction articles involves many production problems and a large number Of these are accentuated by the large area' Since it is impossible in the short space of this Paper to describe adequately all the problems involved, I have thought it best to merely mention some Of them and to place particular emphasis upon a problem that is common to all metal-powder articles, although it is of greater importance in the making of friction articles. This problem has to do with the effect On the properties of a friction article of small variations in the composition. However, before discussing the problems, it is probably appropriate that some mention be made of the limitations on the use of friction articles. Most engineers are familiar with the general field that can be characterized as constituted by clutch facings and brake linings, and undoubtedly have heard many stories of how metal-powder friction articles have had a service life 10 times as long as nonmetallic friction materials, and of instances where metal-powder friction articles have operated satisfactorily where no other material could be used. These instances should not be regarded as criteria for the assumption that metal-powder friction articles are capable of universal use in the friction field and will always outperform other materials. On the contrary, metal-powder friction articles are unsuitable for numerous applications, either on a performance or on a cost basis. Metal-powder friction articles will not replace wooden block brakes for wagon wheels nor cast-iron brake shoes for railway car wheels, to mention just two obvious examples. Metallic friction articles cannot be used where they must act as heat insulatorsl for they have a relatively high thermal conductivity as compared with asbestos. This is a detriment in some uses, as in certain airplane brakes having hydraulic actuators provided with rubber seals. The metallic friction material readily transfers the heat developed at the braking surface back through the material to the rubber seal and destroys it. Within its limited field, metal-powder friction material has proved satisfactory, but many problems are involved in the Selection of the proper material to use in an application and in the commercial pro-

Jan 1, 1945

Discussion Of the paper Of GEORGE K. BURGESS, J. J. CROWE, H. S. RAWDON, and R. G. WALTENBERG, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin NO. 93, September, 1914, pp. 2433 to 2437. ALBERT SAUVEUR, Cambridge, Mass.-The Bureau of Standards has once more rendered a public service. Manufacturers and consumers of steel rails alike should welcome the important results now laid before them by Dr. Burgess and his co-workers. Personally I welcome these results all the more that in the past, as some of the members may remember, I have never failed, when occasion arose, to call the attention of rail manufacturers to the importance of controlling the finishing temperature of their rails. The pioneer metallographic work conducted at the South Works of the Illinois Steel Co. in the early '90s clearly brought out the close relations existing between the manufacture, properties, and finishing temperature of steel rails and I think I may say without fear of being contradicted that the results of this early investigation had considerable influence in drawing the attention of manufacturers to the importance of finishing temperature and of heat treatment in general. The results now before us should be, it seems to me, of great value to rail manufacturers in their efforts to produce a better and, above all, a safer rail. It seems to be demonstrated in this paper that there is no difficulty in installing in rail mills pyrometric outfits, making it possible to record, without interfering in the mill operations, the temperature of the rails as they leave the finishing rolls, or of the ingots as they are withdrawn from the soaking pits, or at any intermediate point in the process of manufacture. The inference necessarily follows that manufacturers should see to it that such pyrometric installations are made, in order that they may actually know, instead of guessing at, the temperature of their rails;, and, for obvious reasons, rail consumers should insist upon such installations. In the rolling of heavy sections especially should care be taken to lower their finishing temperature, seeing that the present tendency is to finish them at higher temperature, whereas, owing to the slower cooling of their central portions, which makes for coarseness of grain, they should, if anything, be finished at a lower temperature than lighter rails.

Jan 4, 1915

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of- liquid Mg-Pb allojs have been determined by an isopiestic method from 18 to 42 at. pct Pb and by a thevmodynumic analysis of the phase diagram frofiz 0 to 100 at. pct Pb. In the overlapping composition range the magneszupn activity values derived by the two methods are in excellent agreement, thus mutually supporting the correctness of the Mg-Pb phase diagram previously determined by the authors and of the acticitzes deriz~ed isopiestically. SEVERAL studies have been made of the thermody-namic properties of liquid Mg-Pb alloys. Wagner and Engelhardt,1 Lantratov,2 Knappwost,3 Sryvalin et al.* and Wilson5 used the electromotive-force method, Scheil and Wolf8 and Schmahl and Sieben" applied the transpiration technique, and the present authors8 utilized the phase diagram to determine the activity of magnesium in the Mg-Pb system. The results of these studies are not in very good agreement and could not be incorporated into a general systematic analysis of the thermodynamic properties of the homologous series of the Mg-Group IV B systems Mg-Pb,8 Mg-Sn,° Mg-Ge,10and Mg-Si.11 The thermodynamic properties of the Mg-Pb system were therefore re investigated by an isopiestic technique which has been developed for similar studies in the Mg-SnB and Mg-Ge10 systems- Lead specimens, contained in iron or graphite crucibles, were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure to form alloys of compositions which depended on their temperatures, the temperature of the magnesium vapor source, and the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE Magnesium (Dominion Magnesium Ltd., Toronto, Canada) of 99.99+ pct purity and lead (American Smelting and Refining Co.) of 99.999 pct purity were used. In the early experiments, Runs 2 and 3, the alloys were contained in uncovered high-purity iron crucibles. Alloys formed in the uncovered iron crucibles had to be chemically analyzed owing to the slight volatility of lead under the imposed experimental equilibration conditions. The compositions of these alloys were determined by a gravimetric analysis of lead as lead chromate. To avoid this problem, the remaining runs were made in covered graphite crucibles machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non- i reactivity of graphite with lead and magnesium has been previously established,' and the experimental procedure has been described in full detail.' In the runs using covered graphite crucibles it was found that the weight increases of the crucibles and their contents after equilibration equaled the magnesium contents of the alloys within the accuracy of the chemical analysis (i0.3 at. pct Pb). Clearly, the small lid openings of the graphite crucibles prevented significant lead losses during a run, and the weight increase was therefore taken as the magnesium content of the alloys. EXPERIMENTAL RESULTS At thermodynamic equilibrium the magnesium partial pressure of the specimens equaled that of the reservoir. Since the magnesium reservoir was always maintained at the temperature minimum of the system, the activity of magnesium of any specimen was given by the ratio of the magnesium reservoir pressure to the vapor pressure of pure magnesium at the specimen temperature. The standard state was chosen as liquid magnesium and the vapor pressure of liquid magnesium

Jan 1, 1968

There were present eleven Directors, the Institute's Legal Counsel, the Secretary, the Assistant Secretary, and twenty-three guests. The Report of the Committee on Nominations (listed elsewhere) was presented and ordered to take the statutory course. The appointment of a Committee on Mine Taxation was approved. An Advertising Manager was appointed. E. G. Spilsbury and A. S. Dwight were appointed as representatives of this Institute on the Franco-American Engineering Committee. The Transactions were presented to the University of Louvain, and the monthly Bulletin to the French Technical Index. Permission was given to publish in full the argument of William H. Shockley on simplified spelling. A committee was appointed to have charge of the publication of the Raymond Memorial Volume. There were elected 70 members, 15 associates, and 1 junior associate. Three members were reinstated and the resignations of two were ac-cepted. The clues of 10 members who had been in active service with the allied armies were remitted. An extension of time for the payment of dues was granted to the 11 members.

Jan 12, 1919

By A. J. W. Headlee

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb1 and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for germanium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 10, 1953

By Thomas M. Drown

AT the meeting of the Institute in New York,, in February, 1880,* I described a process of determining sulphur in metallic sulphides, with especial reference to the determination of pyrites in coal. The process, as then described, is as follows : A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromine is used it must be neutralized by the addition of a :little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.c. of this solution and heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then * Transactions, American Institute of Mining Engineers, vol. viii, p. 569.

Jan 1, 1881

By L. W. Sink, B. H. Kear, S. M. Copley, M. F. Hornbecker

IT is well known that under appropriate conditions of chill casting, many metals and alloys develop a columnar grain structure having a high degree of preferred orientation.' In cubic materials, this principle has been employed to produce shaped castings with a unidirectional cube oriented columnar grain structure as well as shaped single crystals with a cube axis parallel to the growth ais.' "he purpose of this note is to describe how this same principle can be enlployed to produce wires, rods, or more complex crystal Shapes with a variety of conlpositions in cube or random orientations by a single casting operation. The procedure for directional solidification of in Fig. 2. Examination under crossed polarizers indicated that the striations were a second phase (presumably the B19 phase) which frequently forms initially at primary grain boundaries and then grows toward the interior as thin ribbons. X-ray studies on filings of this alloy reannealed at 1300°C for 15 min indicated a strong pattern of the fcc phase together with a substantial pattern of the B19 phase. The un-annealed filings, however, showed only the pattern of a cold-worked, fcc structure. In these two-phase alloys it appears, therefore, that the B19 phase is transformed into a disordered fcc structure by cold-working. The mechanical properties of these alloys would be of some interest since a fcc structure might be expected to possess greater ductility than the or-thorhombic B19 structure from which it forms. The author wishes to thank Mr. Harvey Yakowitz and Mr. Richard Manuszewski for obtaining the photomicrograph in Fig. 2. This research was partially supported by Research Grant DE-02455 from the National Institute of Dental Research. columnar grained ingots involves pouring a melt into a preheated mold having a water-cooled copper chill at its base? and controlling the temperature gradient in the mold so as to maintain columnar grain growth from end to end of the ingot.4 This is illustrated schematically in Fig. l(a). It should be noted that the longitudinal temperature gradient promoting unidirectional columnar grain growth is maintained by heat loss primarily through the solidifying ingot to the chill, so that both the temperature gradient and the growth rate diminish with increasing distance from the chill. As the distance from the chill increases? the columnar structure coarsens, and the perfection in preferred orientation tends to increase progressively. Using this same procedure of gradient solidification, Fig. l(b) shows a simple scheme for producing a batch of crystals having the same cube orientation rather than an assemblage of columnar grains. Wires and rods are produced by cementing ceramic tubes to the wall of the mold. The steep temperature gradient produced in the central chamber is controlled by the mold heater to produce favorable conditions for crystal growth. Clearly the success of the operation lies in the selection of individual growing columnar grains by some kind of orifice at the base of each channel in the mold. Using simple constrictions, experience with nickel-base alloys has shown that 4 -in.-diam holes at a distance of -1 in. from the chill yield crystals within 7 deg of (100); closer control of orientation is possible by placing the crystal selector farther away from the chill.

Jan 1, 1970

By H. A. Shaw, H. G. G. Whitton

This paper describes the use of the electric-arc furnace for the production of tough-pitch, horizontal cast copper shapes and the production of copper anodes from tank house anode scrap. This installation is the only one of its kind in the United States. SINCE the initial use of electric-arc furnaces for refined copper melting on a commercial scale at Copper Cliff in 1936, this type of melting has been of extreme interest to everyone in any way connected with copper casting and fabricating. Early in 1948, Kennecott Copper Corp. decided to build an electrolytic copper refinery at Garfield, Utah. One of the major decisions to be made at that time was the type of furnace to be used for melting cathodes for casting into refined copper shapes and for melting anode scrap for the production of anodes. Based on the results obtained from arc furnaces by the Tnternational Nickel Co. of Canada, at Copper Cliff, and by the American Smelting and Refining Co., at Baltimore, coupled with certain important economic factors such as having an adequate amount of relatively cheap power available at the Magna Central Power Plant, high cost of poles and oil in the Salt Lake District, and the lack of natural gas at that time, the final decision was to install electric-arc furnaces rather than the standard type of rever-beratory furnaces. Experience has shown certain parts of the original installation to have been inadequate or in need of modification. Although the present status of arc-furnace melting at the Utah Refinery is far from perfect, nevertheless substantial progress has been made. At the Utah refinery, copper is melted in three 15-ft diam, size "M" Lectromelt furnaces, two of which are used for melting cathodes and one for remelting anode scrap. Each furnace is energized from a 13,800-225 v, 3-phase, 60-cycle, 6000-kva (at 40°C rise) oil-immersed water-cooled transformer. Auxiliary equipment for each refined copper furnace includes a charging machine, launders, ladle, 40 ft diam Walker-type casting wheel, bosh, and inspection conveyor. The anode furnace differs in that it is charged by hand from an elevated platform and the anodes are picked off the 24-ft diam casting wheel by a takeoff hoist and loaded directly into specially designed trailers, Figs. 1 and 2. Electrical Equipment Electric power to operate the arc furnaces is generated at the Kennecott-owned Magna Central Power Station two miles distant and transmitted to the Refinery outdoor substation at 44,000 v. At this point it is stepped down to 13,800 v and carried through concrete-lined underground tunnels to the switchgear and then to the primary side of the furnace transformers. The power is conducted from the Y-connected secondary bus bars of the transformer to the electrode arms by means of 22 flexible copper cable conductors per phase. Each cable has a cross-sectional area of 1,750,000 circular mils, giving a total area of 38,500,000 circular mils per phase. The power is carried from these cables to the three individual electrode holders by means of water-cooled copper bus tubing. The electrode clamps are incorporated in the electrode holders and are released by air pressure working against a spring in the clamp control cylinder. The movement of the electrode arms is either automatic or manual. The automatic control is used during melting and is regulated by three Westing-

Jan 1, 1954

By Felix Vogel

SINCE the publication of Prof. J. W. Richards's paper on The Schumacher Briquetting Process,2 this process has been in operation on a practical .scale in two plants in the United States, and a few notes on the results obtained may he of interest. An experimental plant, consisting of a toggle press and a hydraulic press, was installed at Johnstown, Pa., together with the necessary bins and other equipment, and an attempt was made to briquette a mixture of Mahoning fines and blast, furnace flue dust, in a ratio of 7 parts of ore to 3 parts of dust. The results were unsatisfactory, in that the briquettes made were not hard enough to stand the severe handling to which they were subjected in the various transferences necessary between the press and the furnace. The trouble was clue to several causes: First, the mechanical arrangement of the plant, which did not lend itself to a proper hardening and loading of the briquettes into the cars. Second, the irregular composition of the flue dust, as to both its lime and its fine coke contents. Third, the variability of the moisture content of the ore, and its viscosity when wet. Fourth, the ratio of fine ore to flue dust; that is, it was attempted to bind in too large a quantity of fine ore for the small amount of flue dust used. The first trouble could be overcome, and has been improved upon in the plant as it stands to-day. The second trouble was important, because of the small amount of dust used as a binder, and might have been easily removed by mixing the flue dust of the different furnaces, which, however, was never done. The third difficulty was more serious, but could have been partly solved, had it been possible to meet this along with the fourth difficulty, by decreasing the percentage of ore in the briquettes. It was proposed to do this, but it seems that the problem at the works in question is, primarily, to prepare Mahoning fines for reduction in the blast furnace, and only secondarily to use up the flue dust, and a solution along this line did not seem to be interesting.

Jan 12, 1913

By J. Versluys

When a well strikes an oil-bearing layer, the oil has a pressure which is generally sufficient to enable it to rise to near the surface (sometimes above the surface). As soon as a well begins to produce, however, the liquid moves through the pores of the reservoir bed and the pressure in the well becomes much lower than the pressure originally prevailing there. At some distance from the well, however, the pressure in the reservoir bed remains unaltered; thus the pressure of the oil has not only to lift the oil, but also to overcome the friction resistance in the pores. The fact that so many oil wells are gushers is a consequence of the energy accumulated in the gas. In gushing the well acts as a gas-lift. A mixture of liquid and gas (the latter partly dissolved in the former) rises vertically from the oil-bearing layer through a cylindrical casing to the surface. In time conditions alter and the well ceases to gush regularly, then the gushing can be further promoted by inserting a narrower tube in the well and connecting the top of the oil string to the tubing. If the action in time becomes irregular, the gushing can be kept up for a further period by forcing gas between the two tubes. In the oil fields the term "gas-lift" is used actually only where extraneous gas is applied, as in the last of the stages mentioned. The action, however, is just the same whether the gas exclusively originates from the formation, or is partly applied artificially. Thus by gas-lift we simply mean a vertical tube in which the energy of gas under pressure, and of dissolved gas, is utilized for raising a liquid. In gushing oil wells the pressure is frequently very high and the absorption coefficient 0.4 (expressed in vol. ratio) of the coexisting gas is not particularly high, so that in reality it should be assumed that a considerable portion of the gas, at any rate at the bottom of the gas-lift, is dissolved in the oil. For water-producing wells this is not usually of such importance. Where the volume of the flowing gas is much greater than that of the flowing liquid, the latter can be suspended in the former in the form of

Jan 1, 1930

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß'. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß' which in turn form the Widmanstatten a in ß'. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.' There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence'..' in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"' ' report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By Edward Steidle

Those who have followed the rapid progress in rock-dusting bituminous-coal mines must admit that opinion crystallized during the year just closed in support of this preventive of coal-dust explosions. Up to 1924 only one mining company in America practiced rock-dusting on a large scale, but during 1924 forty-two companies had adopted this safety measure, and the "boom" is expected to extend over the next two or three years. Alabama is represented by 1 company, Colorado by 3, Illinois by 4, Kentucky by 1, New Mexico by 4, Pennsylvania by 20, Utah by 8, and Wyoming by 1. A total of about 500 miles of entry has been dusted. Illinois leads with 275 miles of dusted entries and Pennsylvania holds second place with about 175 miles. In each case there is a sense of great security, not only on the part of the operator but by the miner as well. It is also interesting to note that during 1924 the compensation rating or inspection bureaus in twelve of our coal-producing states revised their rating schedules so that a credit would be given for rock-dusting. This credit ranges from 10 to 20 cents per $100 payroll. Recent drastic federal and state regulations approved by mine operators made rock-dusting compulsory in bituminous coal mines in Utah, beginning July 1, 1924. Legislative action favorable to rock-dusting may be expected in other states. Colorado has already proposed a change in its laws, and Pennsylvania, Maryland, Washington, and West Virginia are giving the matter consideration. If the rock-dusting problem is handled properly and proves to be entirely successful, no mining man of any standing will delay applying it in his mine. State legislation regarding this matter may or may not solve the problem. At present, the mining companies that are rock-dusting of their own choice are doing it carefully and thoroughly. In Utah, some are doing it conscientiously, trying to get what benefits can be obtained while others are reported to be doing it only to keep within state regulations. In any event, if we are to have new legislation, it is essential that the various states know what they are about and then, if possible, work for uniform regulations.

Jan 1, 1925

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By J. Jolly

THIS short note on the probable character of the organic sulfur compounds in coal can do no more than indicate lines of research. We have no new experimental work to describe, nothing comparable in value with the careful studies of American coals by Powell and Parr1 and Yancey and Frazer.2 A study of the manner in which sulfur compounds exist in British coals (and their behavior on heat treatment) is rendered increasingly necessary by the fact that the British reserves of good coking coals of reasonably low sulfur content are fast being depleted. We believe that it is essentially by a study of the modes of formation, occurrence, and decomposition of the various types of inorganic and organic sulfur compounds in coal that it will be possible, with hope of success, to attack the problem of purifying coals, otherwise eminently suitable for coking, from these objectionable ingredients. Sulfur, so far as is at present known, does not normally occur in the free state in the coal conglomerate, but is chiefly distributed, irregularly, in three forms: 1. As primary constituents of the coal conglomerate, organic in nature and probably associated with those molecular complexes that have resulted from the degradation of the proteins of the plant tissues responsible for the formation of the coal mass. These constituents can be classed as "organic sulfur." 2. As metallic sulfides, e.g., iron pyrites. 3. As metallic sulfates, e.g., calcium sulfate and ferrous sulfate. (The occurrence of these compounds varies with the occurrence and degree of degradation of class 2.)

Jan 3, 1925

By James A. McGurty, Walter J. Koshuba, Samuel G. Gordon, Gilbert E. Klein

ONE of the problems encountered in working with metals at elevated temperatures is the instability resulting from solid-solid diffusion at a -common interface. A determination of the nature and magnitude of this phenomenon is important as related to structural properties of materials potentially useful in high temperature applications. This paper is concerned with the solid state reaction between metallic molybdenum and beryllium at elevated temperatures. In the older literature,' there were no known inter-metallic compounds in the system Be-Mo, and the list of beryllium intermetallics was rather small. New compilations have been made by Smithells' and by Taylor," listing all the then known beryllium binary intermetallic compounds. In addition to these, some new phases have just been reported' in the system Zr-Be and some further compounds of the type MBe,3 have been currently described. The new compound MoBe,, which is reported upon in this paper differs considerably from the above mentioned MBe13 group, and will be discussed in detail. Diffusion Study The nature of the solid diffusion at a Mo-Be interface was determined by sealing a beryllium rod inside a molybdenum capsule and heating at a temperature of 2000°F' (1100°C) for 100 hr. The molybdenum capsule was fabricated from % in. swaged molybdenum rod obtained from the Fansteel Metallurgical Corp. The beryllium metal was obtained from Brush Beryllium Corp. as % in. cold-drawn rod. This material assayed 99.05 pct Be and contained as impurities 0.84 pct Be0 and 0.19 pct Be2C. The molybdenum capsule was % in. in OD x 2 in. long. To prepare it, a concentric hole 0.250 in. + 0.001 in. — 0.000 in. in diam was drilled and reamed in one end of a rod to a depth of 1 '/2 in. A 1 in. long beryllium rod 0.250 in. + 0.000 in. — 0.001 in. in diam was pressed into the molybdenum capsule. A molybdenum plug 0.250 in. & 0.001 in. in diam x 9/16 in. long was then used to seal the beryllium in place. The capsules were placed in a molybdenum resistance furnace and heated at 2000°F (1100°C) for 100 hr. On cooling, the specimens were cut and examined metallographically. Fig. 1 is a micrograph at X250 of a portion of the interface from a transverse section. Four phases are clearly visible, with sharp boundaries between them. Phase A is a section of the molybdenum capsule; phase B is the molybdenum-rich intermetallic composition MoBe,; phase C is the beryllium-rich compound MoBe13; phase D is a section of the beryllium rod. All phases were readily polished to a high metallic luster. The molybdenum-rich phase has a pronounced purple tinge. The beryllium-rich phase (C) is only slightly darker than the pure beryllium. In polarized reflected light, however, it shows striking birefringence between crossed Nicols. The black areas represent flaws or pores in the material. A small representative amount of powdered material from each of the phases was carefully removed under the microscope with a diamond tool. With this material, powder X-ray diffraction patterns were made for the identification of each phase. Table I lists the X-ray diffraction spacings and corresponding indexes characteristic of these intermetallic compounds. Synthesis To establish the formula of the new intermetallic compound, X-ray diffraction patterns were made from powders obtained from solidified melts of known composition. The syntheses were made by

Jan 1, 1952

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By Robert R. Abbott

The influence of various elements in retarding or accelerating the absorption of carbon during the process of carburization is fairly well known. In general those elements which form carbides accelerate the absorption, while those which do not retard it. It has sometimes been wrongly stated that those elements which raise the temperature of the critical range increase the absorption, while those which lower this temperature decrease it. Silicon is a notable exception to this rule, for its influence is to raise the critical range but to lower the absorption of carbon. Some elements which do not form carbides have no apparent influence upon the absorption rate. Carbon itself retards the absorption rate. With a view to obtaining more exact data upon the subject the following experiments were undertaken: 208 steels of different chemical composition were selected to represent most of the types of modern constructional steels. Specimens 2 in. in diameter and 9 in. in length were weighed to milligrams. They were then packed in the special carburizing box shown in Fig. 1, and kept in the furnace for 10 hours at a temperature of 900' C. A duplicate experiment was conducted at 1,000° C. At equal intervals of time the box was rotated in the furnace so that two complete revolutions were made in the 10 hours. This precaution was taken to neutralize as much as possible any effect of unequal heating. At the end of the 10 hours the box was allowed to cool in the furnace with the doors open. The specimens were then weighed again and the increased weight (carbon) determined. In the following table are given the analyses of the various steels, together with the increased weight of carbon expressed in milligrams.

Jan 1, 1914

OF the many categories into which scientific knowledge has been arbitrarily divided, the one that has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry1 provide ample material on the principles of this subject for the student of steelmaking processes; yet with- out exception those texts draw the greater part of their illustrative material from room-temperature data. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development but in the main those applications in which we are here interested can be ex- pressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent respectively the natural and the common logarithm of X. The two are related by In X = 2.303 log X. Logarithms may be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be, helpfu1. MATTER Innumerable forms of matter may be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas. Whenever such a change occurs there is a corresponding change in

Jan 1, 1951

President and Director GROVER J HOLT, '59, Ishpeming, Michigan Past President and Director CARL E REISTLE, JR, '58, Houston, Texas President-elect and Director AUGUSTUS B KINZEL '60, New York City Vice-Presidents and Directors W A DEAN, '58, Cleveland Ohio W W MEIN, JR, '58, San Francisco, Calif L E ELKINS, '59, Tulsa, Okla J L GILLSON,'59, Wilmington, Delaware E C BABSON, '60, Calgary, Alberta, Canada R V PIERCE, '60, Salt Lake City, Utah

Jan 1, 1957

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951