Search Documents

By George Rice

INSTANTANEOUS outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts.

Jan 1, 1931

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By C. F. Floe, N. J. Grant, A. Joukainen

A CCORDING to Guertler,¹ Smith and Hamilton were the first to study the Cu-Ti alloy system, but because of the presence of large amounts of impurities their data are inconclusive. Hensel and Larsen² in 1930 and Kroll³ in 1931 determined the high copper end of the diagram. In 1939 Laves and Wallbaum,4 in a short summary of compound determinations in titanium binary alloys, mentioned the existence of a face-centered cubic compound, Ti2Cu, with 96 atoms per unit cell, and also a compound, TiCu3, which was said to have a deformed hexagonal close-packed structure in which ordering had been observed. The existence of a compound, TiCu, was also found but the crystal structure was not determined. Craighead, Simmons, and Eastwood determined the effect of copper on the allotropic transformation in titanium. The investigation was limited to alloys containing from 0 to 5 pct Cu, using titanium of fairly high impurity content. Experimental Procedure The methods used for determination of the diagram included metallographic examination and X-ray and thermal analyses. The system was first worked out using the higher purity "Process A" sponge titanium and oxygen-free copper. The high titanium region was next determined more accurately using iodide titanium and vacuum-melted, oxygen-free copper. Preparation of Alloys: The alloys were prepared by arc melting under prepurified helium atmos- pheres in water-cooled copper crucibles. The high purity iodide titanium alloys were prepared by melting three compositions along with a specimen of unalloyed titanium in a single charge. A multiple crucible was used which consisted of a copper plate with four cup-like depressions. The unalloyed titanium was melted first and acted as a getter for any oxygen and nitrogen in the melting chamber. Since these elements harden titanium, the hardness of the standard specimen was an index of the highest probable contamination of the alloy melts. The sponge titanium alloy melts weighed from 100 to 200 g each and the iodide titanium melts from 20 to 25 g. In order to insure greater homogeneity most of the alloys were melted, turned, and remelted twice. The larger buttons made from sponge titanium were sectioned or crushed before remelting. These alloys up to 30 pct Cu were further homogenized by forging at 925°C. They forged readily up to 20 pct Cu but numerous cracks were formed in the alloys containing from 20 to 30 pct. Above 30 pct Cu the sponge titanium alloys were homogenized by heating for 200 hr at 850°C under prepurified helium. Similarly, the iodide-grade titanium alloys containing up to 3 pct Cu were homogenized at 1000°C for 24 hr and all others at 880°C for 200 hr.

Jan 1, 1953

RICHARD A. CONKLING (communication to the Secretary*).-Mr. Hager says that his results on the correlation of well logs in the north Cushing field are the opposite to those of the author. Can he, then, explain why the structural dip of the formations increases with depth, as Dr. Ohern, in his criticism, sets forth that it does, and as all who have worked in these fields will admit, if the shales thicken on the crest of the anticline, as he says they do? We are willing to agree with Dr. Ohern that there is some evidence of a slight unconformity below the Bartlesville sand and think that we can prove, from a specimen in our office, that .this unconformity comes at the base of the Bartlesville sand in the south Cushing pool. On the Ingalls dome, in the southeast corner of Township 19 North, Range 4 East, however, we get results the same as those given by the author on Cushing. The Ballard well in the center of the Northeast Quarter of Section 33 is just 10 ft. higher, structurally, according to tile, surface contour, than the Ringold well -in the center of the Southwest Quarter of Section 34. The dip in the Bartlesville sand, between these wells, is 40 ft. and the dip on the top of the Mississippi lime is 75 ft. This also might be accounted for, partly by the unconformity, but the author used the interval between the top of the Oswego lime, which is about 420 ft. above the Bartlesville sand, and the oil horizon found in the lime in the Ballard well-just mentioned above-to find the depth at which the same oil should be found in a well in Section 5, Township 22 North, Range 3 East, 25 miles North. Using this interval below the Oswego in the former well, we predicted within 2 ft. where they would find the oil in the latter well. Of course, we know that it was accidental that we missed it only by 2 ft., but if there were much of an unconformity in this interval it would be more of an accident if we came within 100 ft. of the depth. Since it can be proven from most of the structures in this section that the clip continues to increase downward, below the Bartlesville at least, to the Mississippi lime, it does not seem necessary to the author to try to prove otherwise that the depth at which the shales will tend to thicken on top of a fold, has not been reached above the

Jan 6, 1917

By Paul G. Raffinot

I. INTRODUCTION We are aware that as a general rule zinc and lead deposits located by the Mediterranean Sea contain important proportions of oxidized ores of lead and zinc (cerussite, anglesite, smithsonite, hemimorphite). Although their economical significance is decreasing in favor of totally sulphurous ores*, la Societe Miniere et Metallurgique de Penarroya and its subsidiaries are still operating four small oxidized ore-bodies in Morocco, Spain, France, and Italy (see Figure 1). Not all of these deposits contain exclusively oxidized lead and zinc ores but also sulphides such as galena, sphalerite, and pyrite. However, the very presence of the oxidized ores gives the treatment methods their characteristics and it is bearing this in mind that we think the description of these four mills worthwhile. Flotation remains the basic process. It uses sulphurization in alkaline medium and long chain xanthate in order to concentrate lead minerals (amylxanthate) and fatty amines (sterarylamine acetate) to concentrate zinc minerals.

Jan 1, 1970

By Richard Moldenke

So far as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in excep tional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved

Jan 1, 1927

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By T. R. Ingraham

When aluminum sulfate was decomposed in an evacuated apparatus and the sample cooled, Q alumina was found. The thermodynamics of the decomposition reaction were resolved by measurements of the total pressure of SO3, SO2, and O2 generated over the sample at various temperatures. The results were correlated with other published data to calculate the rmges of thermodynamic stability of the various compounds involved. The thermal decomposition of aluminum sulfate was studied by Wijhler, Pluddeman, and Wöhler1 and by Warner and Ingraham.2 The results of both studies were critically reviewed by Kellogg,3 who observed that "each set of data shows considerable scatter and strong curvature on a plot of log pso3 vs 1/T".3 He agreed with Warner and Ingraham2 that both the discrepancy in the two sets of results and their curvature may arise from the indefinite properties of the particular form of A12O3 which is formed during the decomposition. While studying the thermal stability of other sulfate systems, we had noted the presence of nonequilibrium oxide properties in both the cobalt4 and manganese5 systems, but neither had shown any appreciable curvature on a logPSO, vs 1/T relationship, and the data from both systems agreed reasonably well with prior work. It therefore seemed reasonable to reexamine the technique which had been used in our earlier work on aluminum sulfate.2 The principal difference was that a tightly compacted pellet had been used for the earlier aluminum sulfate work, whereas a loose powder, contained in a platinum boat, was used for our work on other sulfate systems. In addition, a better technique had been developed for dehydrating the samples. From work done on the nickel system,6 we had become aware of the highly protective nature of some sulfate layers on their oxjdes, and hence of the necessity of providing a large surface area of P3e sample when equilibrium was to be attained in a reasonable time. That observation suggested that perhaps a steady state, rather than equilibrium, had been reached in the earlier work on aluminum sulfate. This paper reports a repetition of the experimental work with large, finely divided samples of anhydrous aluminum sulfate. APPARATUS AND PROCEDURE The apparatus used in the experimental work was described in earlier papers.2,7 The source material was Anachemia reagent-grade Al2(sO4)3 - 18H2O which was first partly dehydrated by heating at 400°C for 48 hr and then completely dehydrated by repeated baking of an aluminum sulfate-oleum slush to dryness at 450°C. ? Alas was prepared by decomposing some of the sulfate in a muffle furnace at 800° C overnight. Approximately equal amounts of the 7) alumina and aluminum sulfate were used in the experiments. The finely divided samples were handled under dry box conditions, and in addition some of the aluminum sulfate was decomposed in the apparatus while it was under vacuum, to ensure its complete dehydration prior to sealing the apparatus. The samples were heated to a series of constant temperatures on both increasing- and decreasing-tem-perature programs. Two to three days were required to obtain steady readings of the total decomposition pressure on an increasing-temperature program, and 5 to 6 days on a decreasing-temperature program. Three samples were examined on both programs. Within experimental error, the results for each sample and each program could not be distinguished.

Jan 1, 1969

By G. W. Maynard

In this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporay suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our owu Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in september, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxiug materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slog." This is the keynote of the Siemens direct process. Dr. Siemens says further: " If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, arid the fusion of the earthy matter mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, weshall rind that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonsceous matter per ton of iron contained in the ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By F. C. Stanford

THE work of an engineer is to direct natural forces so that they bring about the results that he wishes to secure. Heretofore he has concerned himself chiefly with physical forces and inanimate objects, until he has secured a truly marvelous degree of control over them. The great problem of the present age is to secure a like degree of knowledge and control of the human factor. Progress has already been made along this line, but, it is only a beginning. Wilhelm Ostwald says that scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to maintain a high average in prophecy. In short, the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essential need of the period is for more brains; if we only had sufficient knowledge and sagacity we could not only solve all difficulties, but prevent them from arising. This generalization holds good for an industrial organization. The most vital need of the management is for more brains. The logical course for an engineer in charge of an industrial organization is, therefore, to direct whatever forces may be at his command toward the development, training, and guiding of all the brains in his organization. This is easier said than clone, for it involves the carrying on toward two objectives, the maximum of productive work, and the development of the individuals who perform it. This is essentially like the rebuilding and enlarging of a plant, keeping it in full operation the while. On the other hand, if the aim is merely for maximum production from an organization, without offering opportunity for development, the final outcome will necessarily be like that f a plant that is driven at full capacity without stopping for repairs or improvements; it eventually becomes so run down that either a complete rebuilding is necessary or else it has to be abandoned.

Jan 2, 1918

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By R. A. Harrington

THE structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in elec-trolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under dif-ferent sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc, The electron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (10-6 cm.). Different investigations of the structure of anodic films have shown widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann&apos;s&apos; X-ray diffraction patterns of eloxal? films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3-§ Burgers, Claassen, and Zernicke3 obtained sharp X-ray

Jan 1, 1940

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year&apos;s symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. &apos;It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved&apos;) and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By K. E. Barrett

Exxon owns a uranium mill and holds two mining leases in Live Oak County, Texas, about halfway between San Antonio and Corpus Christi. The properties make up the Felder Uranium Operations which was reopened earlier this year. Exxon held an oil, gas, and other minerals lease on the J. C. Felder tract, which was adjacent to a relatively shallow uranium discovery by Susquehanna-Western, Inc. on the Marrs-McLean lease immediately south of the Felder property. Drilling in 1967 and 1968 confirmed the presence of reduced uranium mineralization in the basal sand unit of the Oakville formation on the Felder tract, which formed the major part of the roll-front deposit. In 1969 Exxon and Susquehanna-Western, Inc. entered into a sale and purchase agreement which provided for Susquehanna to mine and process Felder ore and purchase recovered uranium. Susquehanna moved an alkaline-leach mill from Wyoming, erected it on the Ray Point property, and placed it into operation late in 1970. Susquehanna mined and processed ore from the Felder and McLean properties through March 1973. Susquehanna ceased operations in March 1973. Exxon then acquired the mill and mill property. Exxon also purchased the mineral rights to the McLean lease, re-negotiated a mining lease for that property, and carried out shut-down programs for the mining and mill areas in the fall of 1973. The project was put on a standby basis until late 1973, when Exxon initiated mine feasibility studies for the project. MINE PLANNING EVALUATION The feasibility study for reopening the Felder Project began in late 1975 and was not completed until late 1976. I will discuss several areas of the feasibility study that required additional work prior to making the decision to renew operations. Ore Reserves Preparations for estimating the ore reserves began with the re-evaluation of more than 1500 natural radioactivity logs from exploration and pre-development drilling that had been completed on the property. These gamma ray logs of non-core rotary drill holes were the principal source of data used in making the estimate. Chemical assays of cores from the deposit were also used in the reserve determination. Electric resistivity and self-potential logs were made along with the gamma ray log. In December 1975 an additional core drilling project was undertaken to confirm the in-place density and radiometric equilibrium characteristics of the ore deposits. Comparison of chemical assays of cores with the U308 values calculated from the logs showed that the unoxidized ores were in radiometric equilibrium. In contrast, cores from anomalies occurring in near surface, weathered, and oxidized zones were in radiometric disequilibrium. Several important decisions were made in developing a mine plan or schedule of production from the Felder and McLean ore bodies. Disposal of Produced Mine Water: The ore bodies of the Felder Uranium Project occur at a point below the ground water table. The ore zones to be mined must first be dewatered to allow removal of mineralized material. In the open pit operations, this is accomplished by maintaining a perimeter ditch around the periphery of the open pit, allowing the interior of the pit to drain and collect into a sump and be pumped from the mine. In addition to anticipated water production from future mining operations, approximately 200M gallons of water was contained in three open pits left from prior mining operations. In two of these existing pits, the water was to be removed and disposed to allow for planned backfilling of waste material into these pits. The third pit would also have to be drained to allow continued mining of an area left from the prior operations. Essentially no ground water information was available for this area. The only data available was water production history from Susquehanna&apos;s mining operation. Two water wells were drilled early in 1976 on the Felder lease for use in obtaining hydrological data. A long term draw-down test was performed by pumping one water well and measuring water level drawdown in both the pumped well and the observation well. From these data, values for permeability and storage coefficient were calculated. These data were then used in modeling the aquifer to allow calculation of water influx into the mining area versus time. Once a schedule of water production, including the stored volume in the existing pits was calculated, alternate solutions for disposal were evaluated. The first system evaluated was a series of deep injection wells. The wells were designed to inject at a depth of approximately 3500 feet. Again very little information concerning reservoir characteristics of the receiving sand units was known. Using assumed values for reservoir permeability and storage coefficients, an injection well system was designed to allow for disposal of produced mine water. The biggest

Jan 1, 1979

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cacha-poal rivers 24 miles below Sewell is Coya, elevation 2500 ft, location of the company&apos;s two hydroelectric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest underground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio. Because the streams flowing from the Andes in the area of Braden&apos;s operations are used for irrigation, it is impossible to dump tailings directly to the river. The tailings pulp must be separated into solids and decanted clear water, and the clear water returned to the same water shed from which the original water was removed. Remaining sands and slime must be deposited in a reservoir where they will not cause trouble to farmers.

Jan 1, 1958

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cachapoal rivers 24 miles below Sewell is Coya, eleva- tion 2500 ft, location of the company&apos;s two hydro- electric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest under- ground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio.

Jan 10, 1957

By Arthur E. Granger

IN the early days of the science, and until the recent past, geologists worked as individuals or in small groups. Prior to 1930 perhaps the largest single group under one administrative head was the Geologic Branch (now Division) of the U. S. Geological Survey, which employed at that time (including temporary help) 100 to 150 geologists. Today that same unit employs some 1500. In industry some companies employ as many as 100 geologists in a single department. These numbers obviously pose a need for administration. The basic qualifications for good administration are the same for any group of human beings, but the administration of geologists presents some special problems. Choosing Administrative Personnel: There are two kinds of personnel needs: 1) technical, which requires professional geologists who have proved their capabilities in the field, and 2) clerical and fiscal, which provide the necessary supporting or housekeeping functions. This discussion will be concerned only with the first category, except to point out the need for competent and understanding help from clerical and fiscal people and close relationship between top administration, technical or professional personnel, and the clerical and fiscal groups.

Jan 7, 1957