Search Documents

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By L. S. Darken

IT has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernst1 in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and Fuoss2 with results which have recently been confirmed experimentally by Harped and Nuttall.3 This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author 4.6 who pointed out4 that "for a system of more than two components it is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepticism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley11 in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion 0f acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 1050°C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By H. V. Fairbanks

Efforts were made to determine the amount of increase in the drying rate which could be obtained through acoustic treatment of ultra fine coal under various conditions, and to test the feasibility of using a rotary kiln and multitiered vibrating screens as a means for continuous drying of coal fines. Introduction of acoustic energy during the rotary kiln experiments increased the drying rates from 10-40%, depending upon the experimental condition. The use of a drying assembly consisting of multitiered vibrating screens produced better results than the rotary kiln and has definite possibilities of providing an effective means of drying coal fines in relatively large quantities.

Jan 1, 1973

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.', ' One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.' The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By Roscoe E. Bell

BETWEEN 1945 and 1948 the author made studies of the western phosphate industry and its potentialities. These included an appraisal of the opportunities for western development of the industry, studies of production costs, of market potentials, of transportation economics, and of industry location. This paper will be directed toward pointing up the factors which have an important bearing on the establishment of fertilizer plants in the western area. Industry Location Factors: There are, of course, an infinite number of possible organizational setups which might require consideration. However, the phosphate industry is simple enough so that studies of the most probable alternatives can be made conveniently. The salient factors which require special consideration in such a study are: (I) the location of the raw materials, (2) the location, size, and character of the present and potential markets, (3) the location of energy sources and materials required for fertilizer processing, (4) the location and capacity of present manufacturing facilities, (5) the cost of assembling the materials and energy needed in manufacturing, and (6) the cost of distributing the manufactured product. Raw Material Supplies: Rock phosphate is the raw material for the manufacturing of phosphate fertilizer. In the United States the important known deposits of this material are located in three general areas (fig. 1). The western deposits, comprising about 60 pct of the nation's supply, are in the four-state area—Idaho, Wyoming, Utah, and Montana. The Florida deposits comprise roughly 38 pct of the national supply. The Tennessee deposits, comprising about 2 pct of the national supply, have been the most important source until recent years. The western deposits, which are virtually undeveloped, have not been used to any extent to meet the nation's need for phosphate rock and phosphate fertilizer. Fertilizer Markets: The large national markets for fertilizer are in the midwestern and eastern United States (fig. 2). The principal far-western markets are along the Pacific Coast, especially in California. Until recent years the western markets have been extremely limited, whereas the markets in the eastern United States have long been established and manufacturing facilities have been provided to meet these needs (fig. 3). In recent years the western markets have expanded very rapidly, continuing to grow throughout the war years and postwar period at a similar rate. The question always arises as to whether this is a temporary war-swollen market which will shrink back to its original size as soon as the present agricultural price levels drop. In order to answer this question consideration must be given to the character of the market (fig. 4). I have considered seventeen western and midwestern states in the western market area where transportation costs from the western deposits are equal to or lower than those from Florida. They include all states west of a line drawn through Chicago, Kansas City and the western boundary of New Mexico. In the mewar period this was a small market totaling only 37,000 tons of P,O, annually. The 1946 total for this same area was approximately 200,000 tons. Considerably more fertilizer would have been used in 1946 had adequate supplies been available. Estimates of future markets are difficult to make, but we do have some indices that are useful. The

Jan 1, 1951

By Roscoe E. Bell

BETWEEN 1945 and 1948 the author made studies of the western phosphate industry and its potentialities. These included an appraisal of the opportunities for western development of the industry, studies of production costs, of market potentials, of transportation economics, and of industry location. This paper will be directed toward pointing up the factors which have an important bearing on the establishment of fertilizer plants in the western area. Industry Location Factors: There are, of course, an infinite number of possible organizational setups which might require consideration. However, the phosphate industry is simple enough so that studies of the most probable alternatives can be made conveniently. The salient factors which require special consideration in such a study are: (I) the location of the raw materials, (2) the location, size, and character of the present and potential markets, (3) the location of energy sources and materials required for fertilizer processing, (4) the location and capacity of present manufacturing facilities, (5) the cost of assembling the materials and energy needed in manufacturing, and (6) the cost of distributing the manufactured product. Raw Material Supplies: Rock phosphate is the raw material for the manufacturing of phosphate fertilizer. In the United States the important known deposits of this material are located in three general areas (fig. 1). The western deposits, comprising about 60 pct of the nation's supply, are in the four-state area—Idaho, Wyoming, Utah, and Montana. The Florida deposits comprise roughly 38 pct of the national supply. The Tennessee deposits, comprising about 2 pct of the national supply, have been the most important source until recent years. The western deposits, which are virtually undeveloped, have not been used to any extent to meet the nation's need for phosphate rock and phosphate fertilizer. Fertilizer Markets: The large national markets for fertilizer are in the midwestern and eastern United States (fig. 2). The principal far-western markets are along the Pacific Coast, especially in California. Until recent years the western markets have been extremely limited, whereas the markets in the eastern United States have long been established and manufacturing facilities have been provided to meet these needs (fig. 3). In recent years the western markets have expanded very rapidly, continuing to grow throughout the war years and postwar period at a similar rate. The question always arises as to whether this is a temporary war-swollen market which will shrink back to its original size as soon as the present agricultural price levels drop. In order to answer this question consideration must be given to the character of the market (fig. 4). I have considered seventeen western and midwestern states in the western market area where transportation costs from the western deposits are equal to or lower than those from Florida. They include all states west of a line drawn through Chicago, Kansas City and the western boundary of New Mexico. In the mewar period this was a small market totaling only 37,000 tons of P,O, annually. The 1946 total for this same area was approximately 200,000 tons. Considerably more fertilizer would have been used in 1946 had adequate supplies been available. Estimates of future markets are difficult to make, but we do have some indices that are useful. The

Jan 1, 1951

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By W. R. Phibbs

THE Columbia Steel Corporation, organized in 1922, and taken over by the United States Steel Corporation on Feb. l, 1930, is operating one blast furnace at Ironton, Utah, which was started on April 30, 1924, and is producing approximately 14,000 tons of pig iron per month. Half of the pig iron produced is basic iron and is used in its own plants at Pittsburg and Torrance, Cal. The ore for the blast furnace is shipped from Desert Mound, Utah, near Cedar City, in the southern part of the' State, approximately 231 miles from Iroaton. The ore is a hematite, disseminated with magnetite, the chemical analysis showing approximately 12 to 20 per cent magnetite, and under the micro- scope the ore has the appearance of a magnetite.

Jan 1, 1930

By Henry N. McCarl

Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in port- land cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggre- gate materials. The value of mineral aggregate materials at the production plant varies from less than a dollar per ton to several dollars per ton for most crushed stone and sand and gravel, $2 to $15 per ton for slag and expanded clay or shale aggregate, to as much as $60 to $100 per ton for expanded perlite or vermicu- lite. The more specialized the use, the higher the price-although there are naturally some exceptions to this rule of thumb. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Light- weight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks there will also be some coverage of sources, mining and production, especially in those cases where they are

Jan 1, 1975

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By T. B. Counselman

WHEN one thinks of Minnesota iron ore, one thinks of big open pits, where high- grade ore is simply scooped up with a power shovel, loaded into cars, and hauled away for shipment to the blast furnace. On the western end of the Mesabi range, however, are large tonnages of iron ore which contain too much silica to be used directly in the blast furnace, and these ores must first be concentrated to a purer form. The Mesabi range is about 100 miles long and a maximum of 3 miles wide. The iron formation, which in its unaltered form is called taconite: consists of a banded iron- bearing chert. Where the high-grade ore bodies occur, these have resulted from folding and cracking with sub- sequent leaching out of the silica, leaving the iron oxide behind. The big open pits and the underground mines are situated in these concentrations.

Jan 1, 1941

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a [?] line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and [?] lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz," This would require many data to prove, but no proof is given; any considera¬tion would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.¬Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg8 have ground

Jan 1, 1941

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By B. F. Bush

THE coal-fields of Missouri, situated hi the northern and western portion of the State, are distributed, in whole or in part, over 57 counties, embracing an area estimated by Mr. Broad-head to be practically 23,000 sq. miles, including small detached beds and outliers in St. Louis, St. Charles, Lincoln and Warren counties in the eastern part of the State. This area includes about 8,000 sq. miles of Upper or Barren Measures, 2,000 sq. miles of exposed Middle, and 12,420 sq. miles of exposed Lower Measures. In a general way, the Missouri coal-field is bounded on the east by an imaginary line entering the northern part of the State just east of the 92c1 Meridian and passing across the State in a southwesterly direction to a point on the Kansas-Missouri line a little below the southern boundary of Barton county. An important part of the field overlaps this line and extends down the northern side of the Missouri river, under¬lying the greater part of Randolph, Howard, Boone and Audrain counties. In all, 34 counties produced coal during the year 1903. Fig. 1 shows the position of the coal-fields in Missouri. GEOLOGICAL FEATURES. The Coal Measure formations, all of the Carboniferous age, rest unconformably upon the rocks of the sub-Carboniferous or Mississippian series, and, in some cases, upon the rocks of the Devonian and Silurian ages. From their outcrop on the eastern and southeastern borders of the field, the Measures dip west to northwest at the rate of 10 ft. per mile, reaching a maximum thickness estimated by

Jan 1, 1905

By J. Th. G. Overbeek, R. Schumann, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.1-3 Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles.

Jan 5, 1954