Search Documents

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By W. A. Hockings, M. E. Volin, A. L. Mular

Batch grinding tests at short times were made in a laboratory rod mill with 10 x 14 mesh quartzite in corn syrup-water mixtures of varying viscosity. The weight fraction broken and size modulus were found to be independent of viscosity up to 20 cp, but at higher viscosities breakage of the feed decreased while the size modulus increased. The mechanisms of the effect of viscosity are discussed on the basis of particle dynamics. The effect of viscosity of the suspending medium on grinding has not been accorded much attention, although both wet and dry grinding are used in bene-ficiation processes and the viscosities of water and air differ greatly. schweyerl investigated the rates of grinding of quartzite in a pebble mill with air, water and glycerol as the suspending media and found the rate in terms of new surface developed per thousand revolutions of the mill to be constant and dependent on viscosity up to 20,000 rev, but to decrease and become independent of viscosity for longer grinding times. Based on considerations of the drag forces exerted on suspended particles and on the grinding media under turbulent and laminar flow conditions, viscosity can be expected to inhibit the rate of grinding in a given system as it changes the flow conditions from turbulent to laminar. The objective of this study was to determine the effect of viscosity of the suspending fluid in the batch grinding of a homogeneous feed of uniform size for short residence times, a region of more practical interest than the long times investigated by Schweyer. In actual grinding operations, the viscosity of the fluid does not change, but the consistency (apparent viscosity) of the pulp increases with additions of fines. In this study the consistency of the pulp was not measured because it was thought that the grinding times were too short to alter the apparent viscosity appreciably.* *Minus 200 mesh quartz at 65% solids has an apparent viscosity of about 25 cp as measured by a simple consistometer. Personal communication from D. F. Kelsall to A. L. Mular. For the purposes of this study, the effect of viscosity on grinding can be shown sufficiently well on the basis of the cumulative weight fraction finer than the feed size at any time, and the size modulus, ku, of the finer than feed sizes. The parameter, ku, is obtained from a form of the Gaudin-Schuhmann equation. METHOD AND MATERIAL The grinding tests were accomplished in a laboratory rod mill 10-1/2 in. long and 8 in. bore with a 20-lb rod charge consisting of two 1-in., eight 3/4-in., eight 1/2-in., and eight 1/4-in. diam rods. The mill speed was 43.2 rpm. Charges of 400 g 10 x 14 mesh Wisconsin quartzite** were ground for times of 60, **Courtesy of Minnesota Mining and Mfg. Co. 120, 180 and 240 sec in 500 cc of fluid made up of corn syrup and water in measured proportions. The temperature of the pulp was measured immediately upon completion of grinding, and the size distribution of the quartzite was determined by a wash-wet-dry screening technique. Corn syrup was chosen because of its high viscosity and ideal viscous behavior, and also because its density is not greatly different from that of water. The viscosity of each fluid mixture was measured with an Ostwald viscometer at 25 C. and a correction was made for the temperature of the pulp according to tabulated values for sucrose solutions. The density differences were so small that they probably did not significantly affect breakage. RESULTS AND DISCUSSION The conditions of the grinding tests, computed viscosities, weight fractions finer than the feed size and values of a and ku are listed in Table I. The values of a and ku were taken from the linear portions of the log-log plots of cumulative weight fraction finer vs size for the various grinding times. The plots for tests in fluids of average viscosity 8.6 cp are shown in Fig. 1. In general all of the sets of curves were linear throughout most of the size

Jan 1, 1965

By D. R. Maneval

The Surface Mining Act of 1977 required a study by the National Academy of Sciences regarding the special mine reclamation requirements of Alaska. The status of mines operating and planned in Alaska will be presented. New mines opening in Alaska must establish a baseline inventory of plants and animals in the mine site area as well as determine pre-mining air and water quality. Current work in these areas will be summarized. Reclamation practices in Alaska and other Arctic countries as practiced currently will be described. A summary of current research in Alaska dealing with revegetation on surface mined lanais, re-establishment of animal populations, and water treatment processes necessary in this pristine environment will be discussed. Included will be future predictions of the direction of mine reclamation in Alaska as more mines enter the industry.

Jan 1, 1984

Jan 1, 1896

By Cleland N. Conwell

Intermittent coal mining has been conducted in Alaska for over a century. The first report of coal in Alaska was by the Veechy expedition of 1826 and 1827. Whaling ships used coal from Corwin Bluff near Cape Beaufort during the early and latter parts of the 19th century. The first coal mine in Alaska-and probably the oldest in the Pacific coast of North America-was opened by the Russians at Port Graham on the southwest tip of the Kenai Peninsula. The mine was operated from 1855 until 1867 when the United States took possession of Alaska. From 1880 to 1915 coal mining was carried on intermittently at several localities including Unga Island, Herendeen Bay, Chignik Bay, Kachemak Bay, and several points along the Yukon River. Small coal mines along the Yukon River provided fuel for the river steamers traveling from St. Michaels to Whitehorse. The area of sustained coal production began with the completion of the Alaskan Railroad from Anchorage to the Matanuska coal field in 1916 and to the Nenana field in 1918. Coal production continued to increase until 1953, at which time the oil and gas fields in Cook Inlet were developed. Oil and gas eventually replaced the Matanuska coal as a means of providing heat and power. The military in the Anchorage area shifted from coal to oil in 1967 causing a decrease in production. The increased demand for electric power in the Fairbanks area offset the decline and coal production started to increase. In 1969-1970 the Golden Valley Electric Assn. (GVEA) constructed a mine-mouth power plant 70 miles southwest of Fairbanks near Healy and a power line to Fairbanks. Location of Coals in Alaska Coals are found in all geographical subdivisions of Alaska. Coal in Alaska ranges in age from Carboniferous to Tertiary, and grade from lignite through anthracite. Fig. 1 shows the locations of Alaskan coal fields. The only fields that have been developed extensively are the Matanuska and Nenana. Fig. 2 illustrates the annual production of coal in Alaska and the ratio of underground to strip mining.

Jan 1, 1973

By H. Sigurdson, C. H. Moore

Extensive studies have been carried out on electric furnace and blast furnace slags obtained in the winning of iron from its ores. These slags normally consist of elements of the gangue minerals present in the ores, as well as the added flux materials. In consequence, melts of CaO, MgO, Al2O3 and SiO2 can be considered as representing typical slag compositions. When a slag of this composition cools, it usually crystallizes according to predictions possible from an equilibrium diagram of these constituents, providing the melt is not undercooled to form glass. The melt is either viscous or fluid, depending upon the ratio of binary cations to silica, and crystallizes easily or forms a glass for the same reasons. If the melt is not overheated so that carbides of the metal components of the slag are formed and if the composition of the slag is so adjusted that it has a high fluidity, liquid equilibrium is attained and the slag can be held in a liquid state for extended periods of time. Upon tapping, the slag crystallizes into minerals, the type and proportion of which are determined by the melt composition. Since equilibrium is attained, the holding period is not critical. In melts containing a large increment of titanium, however, the normal slag procedures are not applicable. Titanium, as one of the atomic transition elements, is, at elevated temperatures, capable of being reduced to form metalloid compounds much more readily than the refractory oxides present in normal slags. In consequence, an oxide melt containing titanium never reaches equilibrium in a reducing environment, but continues to shift its composition until cooled. If melts of this nature are cooled and samples submitted to metal-lographic and X ray analysis the course of reaction and crystallization in this type of slag can be determined. Preparation of Slag The slags investigated fell into the system CaO-MgO-TiO2-Al2O3-SiO2 and were produced from ilmenite ores reduced by carbon in an electric furnace. Since the equilibrium series1 and the laboratory smelting of ilmenite2 are described in two of the accompanying papers, detailed description of the smelting procedure is not required here. However, certain essentials must be mentioned. Two types of melts were used to produce slags studied in this investigation. The first series of smelts made to determine proper flux addition were produced in a 4 lb Ajax induction furnace. The charge, consisting of ore with the proper flux addition, was heated in a graphite crucible until fluid, held fluid for a sufficient time period to obtain 1-5 pct FeO content, and poured. Because of the small size of the charge only the final sample of these melts could be examined. In the melts made in the 50 lb arc furnace, however, grab samples taken at 10 min. intervals between time of initial melting and final pouring were available for examination. These samples allowed a much clearer picture of the course of reaction and crystallization. amounts of ferrous oxide and reduced titanium compounds is opaque to transmitted light. Therefore, all petro-graphic studies had to be made on polished slag sections. A representative sample of slag was cut or broken, mounted in a thermosetting plastic, ground flat using 400 grit silicon carbide, the coarse scratches removed with 600 grit silicon carbide and polished on billiard cloth using levigated alumina. Rouge was avoided because of the entrainment of the red particles in pores in the slag, causing a possible confusion with some of the mineral phases. In order to prevent sample projection above the plastic surface red bakelite was used to hold the sample, and backed up with clear lucite. In this manner sample labels could be permanently retained in the mounting. The polished samples were examined on a Bausch and Lomb metallograph at magnifications of 250 X, 500 X, 1000 X and 1800 X. The instrument was equipped for examination of specimens under bright field illumination and with crossed nicols. A magenta tint plate to aid in color tone differentiation was also used. Petrology of Slags In order to determine the composition and mineral relatinos of a previously unreported system petrologically, it is essential that the starting composition, reaction temperature and final composition be known. The chemical composition of the ilmenite ore used in these smelts is given in Table 1, and the complete analysis of a typical high titanium, low iron slag is given in Table 2. In the winning of TiO2 from ilmenite by a smelting process it is necessary to produce a slag which will melt at an economically feasible temperature, remain molten as the iron is removed by reduction, be fluid enough to be readily removed from the furnace, contain a high percentage of TiO2 and a low percentage of reduced titanium com-

Jan 1, 1950

T. A. Rickard, Denver, Colorado: The observations made by the author concerning the treatment of gold-bearing ores, deal with the subject only briefly and in a general way; but, coming from an authority, they invite comment. In stating the fact that a " finely-divided condition " is a necessary characteristic of ores containing free gold, the author must be refer ring to those mining districts only with which he himself is ac quainted. The statement would not be true of certain gold-mining regions in America and Australia. The ores of some Californian mines and the mill-stuff treated at certain of the mills of Clunes and Ballarat in Australia, and of Otago in New Zealand, contain the gold in a free but in a coarse state. Moreover, "reduction to fine sand and flour" is not required by certain ores, even though the gold be in a finely-divided condition. In such cases the gold becomes de tached from the quartz before the gangue has been pulverized into particles as small as those in which the gold occurs. The dry-crushing of free-milling gold-ores is onknown in the new mining regions of the world. It is not clear whether the author has in mind any European district in which such a process is in actual use. If he has, a description of the method and the results obtained would be very valuable. Dry-crushing is, other things being equal, twice as slow and twice as expensive as wet-crushing. In the case of free-milling gold-quartz it serves no purpose, since such ore does not carry sulphides which contain any large percentage of value, and which, by being slimed, may carry away part of that value. The dry-crushing of a free-milling gold-quartz would be considered an absurdity by an American metallurgist. If the ore contain "free gold only," why submit it to a further treatment, such as concentration, after its passage over the amalga mating-plate ? What does the author propose to concentrate ? Again, why anticipate the treatment of tailings by the McArthur Forrest, or some other process ? The satisfaction felt by a mill-man in saving gold by a subsequent treatment of the tailings from his mill appears to me to be like that of the man who shoots at a rabbit,

Jan 1, 1894

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30. Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a, community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo.

Jan 1, 1937

By G. W. White

Over the past several years, the steady progress of gas lift from a mysterious art into a developing science has been traceable through the many fine papers that have appeared in Journal of Petroleum Technology. Consequently, this magazine has rightly become a standard for the serious students of gas lift all over the world. The following discussion is offered in a sincere attempt to accurately present certain topics covered in the subject paper in the light of acknowledged state of the art procedures. INSTALLATION DESIGN The first point to be questioned is the author's installation design, beginning with Eq. 6. The use of 1,200 psi in the spacing equation instead of the 1,275 psi noted as available seems, at first glance, to be a simple arithmetic error. Upon further examination, it appears evident that both this 75 psi plus the 100-psi safety factor must be subtracted from available kickoff pressure because of conditions imposed by the characteristics of the ASC valve (see Fig. B-1). Pressure-charged valve design is incorrectly penalized by spacing the first valve using only 1,100 psi. The use of such a high back-pressure makes it appear that a typical ASC installation would require no more valves than a comparable conventional valve installation. Using a value of 100-psi tree pressure, the well could be valved to 11,000 ft very conservatively with seven pressure-operated valves, but would still require 11 ASC valves. The use of 400-B/D spacing gradient for a 140-B/D rate is not an accepted practice using precharged valves. The author would have done well to note the advantages to be gained by reducing the 500-psi tree pressure, which is clearly explained by Beadle, Harlan and Brown.' In Step 1 of Part III of the continuous flow discussion, the author incorrectly applies the Poettmann and Carpenter curves.2 Item 2 is an incorrect statement. An excellent reference on this point is the paper by Baxen-dell and Thomas.' VALVE MECHANICS The next topic relates to the mechanics of precharged valves. Eq. 2 for the ASC valve can be used to describe the condition of equilibrium, wherein the valve is closed with opening pending. When this equation is used to determine relative values of casing, dome and tubing pressure with conditions approaching the transition value, some strange results are obtained. The following uses the author's symbols and values given on page 689. Fig. B-1 shows the condition that exists at the moment an ASC valve has been uncovered during the unloading process (Condition I). The obvious result is a locked condition. The basis for the curve is shown on the figure which includes 1,000 psig casing pressure to uncover the valve. If injection gas is not bled off the casing until the pressure is decreased by an amount exceeding the stabilizer discharging valve pressure, upward adjustment of the casing pressure is mandatory for the valve to open and unloading operations to continue. In Condition I the dome pressure exceeds the casing pressure by 20 psi, and the tubing pressure required to open the valve is 1,212 psig. This tubing pressure would not exist under the assumed conditions. In Condition I1 the casing pressure is increased to the dome pressure, and the tubing pressure required to open the valve is 1,102 psig. It is apparent that the casing pressure must be increased to a value exceeding the dome pressure before unloading operations could continue. In Condition I11 a maximum casing pressure of 100 psi (stabilizer charging valve set pressure) above the dome pressure is reached, and the tubing pressure required to open the valve is 549 psig. The author's statement after Eq. 5 that "the minimum tubing pressure required to open an ASC valve is equal to the casing pressure at depth less the transition pressure of the valve" is incorrect except for Condition I11 only. Otherwise, the equation is invalid.

Jan 1, 1965

Reynolds Jamaica Mines, Ltd., has received a $3+ million loan from ECA for the development of what are termed the largest bauxite deposits in the world in Jamaica, B.W.I. This amount is in addition to $11 million already provided. The new agreement calls for delivery of 750,000 tons a year beginning in early 1952. Inco has announced a new alloy containing 35 pet Ni which can be used for many purposes served by the old alloys which ran up to 70 pet Ni. The new alloy "Incoloy" is 35 pet Ni, 20 pet Cr, and the balance iron.

Jan 8, 1951

By David Baker

When the skip-hoist was first tried as a means of filling the blast-furnace it made a great many enemies and very few friends among furnace managers. This state of affairs continued until the Duquesne furnaces were built, which demonstrated not only the possibilities of a furnace-stack in the way of production, but also the ability of the skip-hoist to charge the materials necessary to produce the large tonnlage obtained. Every furnace manager, who has operated stacks fitted with the vertical hoist and the hand-barrow system of filling, remembers that the momentous question about the furnace, particularly during a good run, was: "Are you keeping her full ?" and many a good run has been spoiled by the furnace " getting away from the men." With the new birth of the skip-hoist this trouble was eliminated ; but alas! Other and more important difficulties arose. The distribution of the stock, the importance of which is never learned until many different ores and fuels have been tried, demanded closer attention. With all the defects of the hand-barrow system, the distribution—When the top fillers were conscientious in carrying out the scheme of filling arranged after thoughtful consideration by the manager—mas above criticism. It is said that the modern skip-hoist, equipped with an elliptical hopper and receiving-cylinder, and discharging over a small bell into the main hopper, will give just as good results as those obtained with hand-barrow charging, but I cannot agree with this statement. I grant, that under very favorable conditions, the mechanical furnace-top will do apparently as well as the

Jan 1, 1905

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.' That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958

By E. S. Machlin

The alternate processes by which solute atoms can limit the migration of grain boundaries have been considered. At the lowest solute concentrations the controlling process is "mechanical breakaway" in which the solute atoms affect the driving force and not the mobility. In the next higher range of solute concentration, solute atoms are bound to the boundary and diffuse by boundary diffusion along cusps in the boundary developed at the solute atoms. In this region the boundary velocity is controlled by the component in the direction of boundary migration of the rate at which the bound solute atoms can diffuse along the boundary. At still higher concentrations, it is predicted that boundaries break away from the binding solute atoms by thermal activation. The specific behavior Predicted is consistent with the observations of Aust and Rutter. The most striking agreement between prediction and experiment is that obtained for a range of solute concentration in which the boundary velocity is inversely proportional to the cube power of the solute concentration. MaNY models have been devised for the atomic steps in the motion of a grain boundary. McLean1 has listed some of these models and Aust and utter' have evaluated these and other models. If there are

Jan 1, 1962

By H. M. Chance

Adequate treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed " intrinsic value " must be limited to materials that are essential to existence—air, water, food. But " intriusic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable. Possibly for present purposes the value of any material may be considered as having a dual origin: First, that due to economic

Jan 1, 1914

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By W. Rostoker, S. A. Spachner

STUDIES of precipitation phenomena by use of X-ray diffraction effects have shown that atoms of the precipitating phase initially form lattices of limited periodicity in two or three dimensions.1, 2 Such diffraction effects are usually plotted in reciprocal space to facilitate identification. Atomic chains, or gratings possessing unlimited periodicity in only one dimension, cause uniform intensity planes in reciprocal space. Platelets, or gratings possessing unlimited periodicity in two dimensions, cause uniform intensity rods in reciprocal space. Such studies have been accomplished by use of white radiation (Laue technique) or characteristic or monochromatic radiation used with rotating single crystal or Weissenberg cameras. Each one of these techniques have associated drawbacks. If the Lque or rotating single-crystal technique is used, the results which are obtained may be ambiguous.3 Diffraction photograms made with a WeisSenberg camera do provide a direct but distorted representation of the variation of diffracted

Jan 1, 1960

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917