Search Documents

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By F. A. Forward, J. Halpern

A new process is described for extracting uranium from ores containing sulphidic minerals, which comprises treating an aqueous pulp of the ore with air or oxygen at elevated temperatures and pressures. The acid required to dissolve the uranium is generated during the leach through oxidation of the sulphides. The chemistry of the process is discussed and laboratory results are presented to illustrate the operation of the method and the variables which control it. With most ores, leaching at a temperature of 130°C and an oxygen partial pressure of 10 psi provides uranium extractions of 90 to 95 pct in 4 to 6 hr. The acidity and level of dissolved impurities in the leach liquor can be kept fairly low. The method is characterized by a number of advantageous features including low reagent cost, short retention times, and high recoveries. RECENTLY there have been developed several processes for extracting metal values from ores by pressure leaching techniques;' -' an example is the carbonate leaching process for uranium ores which has been studied in this laboratory.' Leaching is carried out under oxygen pressure to ensure oxidation of the uranium to hexavalent compounds which are soluble in carbonate solutions. During the course of investigations relating to this process, it was observed that sulphide minerals, such as pyrite, usually were oxidized under the conditions of the leach treatment resulting in the formation of iron hydroxides and sodium sulphate, i.e. 2 FeS= + 7Vz O2 + 8 Na,CO3 + 7 H,,O -* 2 Fe(OH)3 + 4 Na2SO4 + 8 NaHCO.,. [1]

Jan 1, 1956

By D. R. Hay, E. Scala

Electrotransport has been superimposed on the rate-limiling- step in zone refining which is the impurity diffusion through the liquid at the solid/liquid interface. The efficiency of zone refining is increased and relative resistivity ratios (P300°k/P4 2°K) he increased by 50 pel in tungsten for a given number of posses using- the electrotransport field-aided method. The effiect of zotze refining in the presence of an electric field on the relative resistivity ratio is examined as a function of its intensity and polarity. THE effect of electrodiffusion on the effective distribution coefficient of zone refining has been discussed by Pfann and Wagner.' Control of the distribution coefficient in zone refining is of twofold interest. A distribution coefficient of unity can be increased or decreased, making possible the transfer of some previously inseparable solutes. The general efficiency of zone refining can also be increased. In the conventional zone-refining process impurities are removed by their retention in the molten zone and subsequent deposition at the end of the rod after a complete passage of the zone. In higher-melting-point systems a second mechanism may also operate, the volatilization of impurities from the molten zone. It has been suggested by schadler2 that, in refractory metals, vacuum distillation plays the predominant role in purification. In Koo's results,3 the resistivity ratio decreased beyond a zone-refined length of 6 in. from the starting end, indicating that some purification does in fact occur by true zone-refining action. Hay and scala4 showed that the degree of purity as measured by the relative resistivity ratio method depends on the square root of time in the molten zone (number of passes) and thus appears to be limited by diffusion in the boundary layer at the solidifying interface assuming good mixing in the body of the molten zone where a linear rate would prevail. The final concentration of impurities in electron-beam floating-zone purification depends very much on the operating conditions and results obtained by various investigators2,3,5 are difficult to correlate. The diameter of the starting material, operating vacuum, and rate of traverse are among the factors to be considered. There are, nevertheless, some general observations to be obtained from the literature. Lawley5 reviewed the literature up to 1962 and concluded that the major contaminants generally remaining in tungsten after electron-beam zone refining are molybdenum and carbon. Molybdenum due to its high melting point and distribution coefficient of nearly unity would be expected to be difficult to remove by either volatilization or zone refining. Carbon is not only a common contaminant in vacuum systems, but is also very difficult to remove by conventional vacuum melting. even with vacuums of 10-7 mm Hg. For each of those impurities removed by zone refining the equation of Pfann and Wagner may be applied: It relates the effective distribution coefficient k to a superimposed driving force which accelerates the solute away from the interface with a terminal velocity L" and to the more conventional zone-refining parameters; v = rate of traverse, t = thickness of the diffusion layer at the solidifying interface, D = diffusivity of the solute in the molten zone, and ko = equilibrium distribution coefficient of the impurity.

Jan 1, 1965

By D. M. Wade, F. F. Redfield

PRODUCTION at Aguilar started in 1936 and by 1942 the mine had reached a peak of 25,000 tons a month. Present production is only about 60 per cent of this capacity because of difficulties in railroad transportation and the rationing of fuel oil brought about by the war. In the early years, cut-and-fill stopes were tried, but square sets were found to be the most practical method in the southern section of the mine, where blocky, treacherous ground and greater mining widths are prevalent. Square sets and opencut mining were the rule until 1942, when it became increasingly difficult to get mine timber. The ore beds in the northern section of the mine were found amenable to cut-and-fill stoping as the rock was firmer and the veins narrower. At present 69 per cent of the ore comes from cut-and-fill stopes, 27 per cent from opencut, and only 4 per cent from square-set stopes. Massive galena and sphalerite with comparatively little quartzitic gangue constitutes the higher-grade ore. The gangue minerals that can be detected by eye in low-grade ore are rhodonite, wollastonite, and pyrrhotite. Wall rocks range from shale to quartzite, with occasionally a little limestone.

Jan 1, 1947

By Louis Huber

DESPITE the fact that centrifugal fans were first developed for ventilating mines and that artificial ventilation was first practiced in mines, the lack of knowledge of mining men on mine ventilation in general, and on fan performances and characteristics in particular, is very much in evidence today. While it is true that mines are much better ventilated now than they were 20 to 30 years ago, we have made very little progress in the study of mine ventilation, or in mine ventilating fan design. Today the average mine operator is woefully dependent on the engineers of mine fan manufacturers when he is in the market for a fan, and this situation works to the disadvantage of both the operator and the manufacturer. The former may be imposed upon by an unscrupulous sales engineer and induced to buy a fan which is not the proper one for the mine; when it is operating it may be wasteful of power and even accessory to a serious mine disaster. More often, however, it is the fan manufacturer who is imposed on. If the operator asks the manufacturer to build for him a fan that will deliver a certain quantity of air against a certain specified pressure and requiring a specified number of horse power when operating under these conditions, the manufacturer may build a fan that will comply with these specifications to the letter. When the fan is installed it is frequently found that it is delivering a greater quantity of air against a lesser pressure or a lesser quantity of air against a greater pressure, and is requiring more horse power than specified in the first case and less than that specified in the second. In either case the operator usually upbraids the manufacturer for not meeting specifications, and refuses to pay for the fan. The trouble in either case outlined above is that the pressure necessary to force the specified quantity of air through the mine has been estimated incorrectly by the operator or his engineers. When a fan is designed and built to deliver a certain quantity of air against a certain specified resistance it will operate at its maximum efficiency only when it is operating under

Jan 2, 1926

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By Nicholas J. Grant, Robert F. Wilde

TAYLOR and Floyd's"" work in establishing phase diagrams based on the elements Ni-Cr-Ti-A1 has led to an understanding of the precipitation hardening mechanism in alloys based on these elements. Nordheim and Grant4 concluded that in simple alloys, and where the aluminum to titanium atomic ratio was such that less than three out of five aluminum atoms were replaced by titanium, the precipitate on aging is the face-centered-cubic Ni 3A 1 phase, called They further found that increasing amounts of hexagonal ? phase, Ni3Ti, precipitated from these alloys when the titanium content exceeded the solid solubility of both matrix and Ni3A1. For alloys of Ni-Cr-Ti-Al, in which the titanium and aluminum contents each ranged from 0 to 4 wt pct, the titanium-rich was superior for strengthening to either pure ?' or 7. It was also noted that the combined titanium plus aluminum content (atomic pct) was a direct measure of the high temperature strength and overaging temperatures for these alloys.4 The present investigation was undertaken to extend existing data on precipitation hardening in the more complex commercial alloys containing higher titanium plus aluminum, and with significant quantities of cobalt, molybdenum, and carbon. Experimental Procedure Reforging of As-Received Bar Stock—The alloys were received as ground, forged bar stock. Chemical analyses and the as-received bar diameters are shown in Table I along with the ASTM grain size after the various treatments. All stock except the Waspaloy was reforged to % in. diam to gain material and to facilitate machining of stress-rupture specimens. Forging was carried out at 2100°F, and discontinued when the bar temperature fell to 1800°F. Heat Treatments—For experixental simplicity it was desirable to heat treat all of the alloys at, the

Jan 1, 1958

By Wayne L. Worrell

Thermodynamic data for the stable carbides and oxides of chromium, molybdenum, and tungsten have been critically eualuuted and are used to determine the stable condensed phases at 1 atm total pressure in each metal-carbon-oxygen system. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures neces.see)*y to oblain these metals by corbolhermic redlrction under reduced pressures. USING recently reported data for the carbides and oxides of chromium, molybdenum, and tungsten, the stable phases in the Group VI metal-carbon-oxygen systems at specific temperatures and pressures can be determined. The thermodynamically stable regions in each metal-carbon-oxygen system can be completely pictured using a Pourbaix-Ellingham diagram in which the two coordinates are oxygen potential (-RT In Po2) and temperature. Worrell and chipman' have described and constructed such diagrams for the metal-carbon-oxygen systems of vanadium, columbium, and tantalum. Downing2 has used similar diagrams to provide a description of the reactions in submerged arc furnaces. One of the examples which he cited was the Cr-C-O system; however, an improved diagram is presented in this paper using recently obtained data for the carbides of chromium. Although some of the oxides and carbides of the Group VI metals exist over slight ranges of composition,3 all solid phases are represented as stoi-chiometric compounds in the subsequent diagrams. Any error introduced into the calculated equilibria by neglecting the compositional variation of these phases is less than the uncertainty in the thermodynamic data. In a Pourbaix-Ellingham diagram for a three-component system, the phase rule requires that at equilibrium four condensed phases specify a point, three condensed phases determine a line, and two condensed phases define an area. To obtain a well-defined area at high oxygen potentials and teniperatures, the initial carbon to oxygen mole ratio is specified to be more than sufficient to reduce the oxide but not enough to convert all the metal to carbide. Thus, the lowest regions in the subse- quent Pourbaix-Ellingham diagrams represent areas in which the metal and its carbide are the stable condensed phases. Cr-C-O SYSTEM A) Thermodynamic Data. To simplify the subsequent calculations, all thermodynamic data are presented in the form of linear Gibbs-energy-of-formation* equations which were derived for the temperature range 505° to 2000°K and are reasonably accurate over the entire temperature ranges of the diagrams. The thermodynamic data for the compounds occurring in the Cr-C-O system are summarized in Table I. Several volatile chromium oxides have been reported,4 but their influence is negligible in the Cr-C-O system. Thermodynamic data for CO and CO2 were taken from the compilation of Coughlin.5 The only solid chromium oxide sufficiently stable to exist below 1800°K in the Cr-C-O system is Cr2Os.11 The Gibbs-energy-of-formation equation for Cr2O3 was obtained by revising the data tabulated in Coughlin,5 using the heat of formation of ah' and the high-temperature thermal data for chromium.7 In 1953 Richardson8 re-evaluated the original work of Kelley and coworkers,9 who measured the thermodynamic properties of the chromium carbides. However, the high-temperature equilibrium results of Boericke9 yield values for ?G°f of Cr2O3 which are 2 kcal more positive than the accepted data. His results for the chromium carbides are based on the same questionable equilibria. Gleiser10 recently determined the Gibbs energy of formation of Cr3C2 and the equation in Table I was calculated from her data and the thermal data of Kelley and coworkers.9 Thermodynamic data for the Cr7C3 and Cr23C6 carbides were obtained by combining the Cr3C2 data

Jan 1, 1965

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

The following is an incomplete list of members and guests who called at Institute headquarters during the period Apr. 10, 1919, to May 10, 1919. Arthur K. Adams, Spencer, Mass. Ensign Floyd D. James, U. S. S. Fulton. W. T. Bates, New York City, N. Y. J. Harry Johns, Thorsden, Woking, A. D. Brokaw, Washington, D. C. England. E. H. Clausen, San Francisco, Calif. W. F. Jones, Rock Springs, Wyo. W. M. Corse, Mansfield, Ohio. E. L. Lasier, Washington, D. C. E. O. Daue, Philadelphia, Pa. John M. Lovejoy, New Rochelle, N. Y. G. D. Dub, Washington,, D. C. 2d Lieut. James F. Magee, Lancaster, S. B. Eaton, Dover, N. J. Pa., Sherman Eaton, Smethport, N. C. Ernest Marquardt, Casper, Wyo. J. A. Endweiss, La Jolla, Calif. Geo. B. Marshall, Abangarez, Costa Edgar W. Engle, North Chicago, Ill. Rica. 2d Lieut. Maxwell E. Erdofy, New York Benj. L. Miller, So. Bethlehem, Pa. City, N. Y. Major Desaix B. Myers, Camp Mills. Chas. A. Fellencer, Allentown, Pa. Edmund Newton, New York City, N. Y. Arthur Feust, Joplin, Mo. Seely B. Patterson, Jr., Allentown, Pa. Ensign Harold P. Ford, U. S. S. Radnor. Wm. R. Pearson, New York City, N. Y. A. D. R. Galloway, Accra, West Africa. Harold C. Price, Langeloth, Pa. R. C. Gosrow, Milwaukee, Wis. T. C. Roberts, East. Orange, N. J. C. A. Grabill, El Paso, Tex. P. H. Royster, Washington, D. C. Hobart A. Hanks, San Francisco, Calif. W. H. Staver, New York City, N. Y. John L. Henning, Lake Charles, La. N. L. Wimmler, Bangkok, Siam. 1st Lieut. J. Parke Hook, Philadelphia, Capt. Jay P. Wood, New York City, Pa. N. Y. An item in the May Bulletin made it appear that Frank W. DeWolf had just become connected with the State Geological Survey of Illinois. This was one of the inadvertences of war. Mr. De Wolf has been Director, or Chief, of the State Geological Survey for approximately ten years. Through the courtesy of the Governor of Illinois, lie was loaned to the Bureau of Mines for about seven months, after which period he resumed his former position.

Jan 6, 1919

By H. M. Roche

MAGNETITE mining and milling in the Eastern States in 1939 showed considerable improvement over 1938. For the first eight months of the year production of magnetite proceeded at a normal rate but operations were stepped up in the last four months owing to increased domestic demand. In New York, the Republic Steel Corp. operated the Witherbee-Sherman mines at Mineville throughout the year. Chateaugay Ore and Iron Co. operated their low-phosphorus mine at Lyon Mountain for the first seven months, but on Aug. 1, Republic Steel took over this mine -and have since operated it. In Pennsylvania, the Bethlehem Steel Co, operated the Cornwall mine continuously. In New Jersey, Mt. Hops and Scrub Oak were in operation all year. The Washington mine went into production on Nov. 1 and the Richard mine on Dec. 1.

Jan 1, 1940

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

By M. J. Coolbaugh

Mining potash at depths of 3000 ft or more beneath thick water-bearing sediments in Saskatchewan presented a unique challenge to the North American mining industry. Potash is known to flow under pressure, but the knowledge of its flow characteristics at great depths was inadequate for safe design of mine workings and for assured protection from water above the salt formations. At the 3000-ft. depth of the Canadian mines, the potash is stressed beyond its elastic limit, and therefore mining design must deal primarily with its behavior as a plastic material. Recognizing that careful study would be required in order to assure safety and stability of mine workings in deep potash, IMC initiated an extensive rock mechanics investigation of structural properties of potash and salt under high-stress conditions. This presentation consists of a brief review of the development of some methods of testing potash in the laboratory and in the field; some of the rock mechanics concepts and principles derived; and their application to potash mine design. The mining of potash more than 3000 ft beneath the water-bearing sediments in Saskatchewan presented the unique challenge of designing stable mine workings and assuring protection from overhead water in a material that was believed to flow plastically, but whose behavior as a plastic material was not sufficiently known. Under the stress conditions ordinarily encountered in mining, most rocks behave as elastic materials; that is, they compress slightly under pressure, and rebound when the pressure is released. Salt and potash, however, are different. Even under the relatively low pressures encountered at shallow depths, these materials become slightly plastic and yield to stress by flowing.* The plastic properties become more pronounced at greater depth and pressure, and the question arises as to whether or not the plastic flow will be rapid enough and exert enough pressure to destroy underground structures or interrupt the mining process. It was found, however, that not only was there an insufficiency of information about the behavior of potash and salt, but conventional methods of testing these materials, such as determining the modulus of elasticity, Poisson&apos;s ratio, and uniaxial compressive strength, were inapplicable because of the high stress conditions prevailing at the 3000-ft depth. Potash under high pressure, for example, has practically no modulus of elasticity, its stress-strain relationship varies with time, and its compressive strength depends upon the degree of confinement. Elasticity and Stress/Strain Relationship: Fig. 1 shows a standard stress/strain chart for potash as made by the Department of Mines in Canada. Typically, when stress is applied to a hard-rock specimen, the specimen contracts, then expands to its original shape when the stress is withdrawn. This chart illustrates, however, that potash under stress yields to the stress by flowing, and does not expand when the stress is withdrawn. When the applied stress was held constant for 30 min, beginning at points A and C, the strain continued to increase and the potash flowed to points B and D, respectively. Points B, D, F, and H show that the potash did not return to its original shape when the stress was released. Thus it can be observed that potash has practically no elasticity and that the amount of strain depends upon the length of time that the stress is applied. Compressive Strength: The conventional method of determining the compressive strength of hard material is to find the maximum pressure that long slender specimens of the material can withstand without failing. As illustrated in Fig. 2,* line B, a standard 2-in. cube of potash subjected to a conventional type of uniaxial compressive test will exhibit a strength of about 5000 psi. However, the compressive strength exhibited can be made to change by changing the conditions under which the test is made. For example, if teflon plates lubricated with graphite are inserted between the press and the specimen, thus minimizing end constraint, the compressive strength is only about 2500 psi, shown in line A. If a specimen is cut in half, changing the width-to-height ratio to 2 : 1 instead of 1:1, and then tested without lubri-

Jan 1, 1968

By M. A. Quader, D. Kuhlmann-Wilsdorf, R. A. Dodd

STACKING fault tetrahedra were first observed in quenched and aged pure gold by Silcox and Hirsch1 and identified as defects originating in the collapse of vacancy discs on {111} planes. It was supposed that sessile loops are the first product of the collapse, and that by a dislocation dissociation/glide sequence these are converted into tetrahedra. Although the tetrahedra can be mechanistically accounted for in this way, recent investigations indicate that their growth occurs by the absorption of individual vacancies on small nuclei involving perhaps as few as six vacancies.2-7 Besides stacking fault tetrahedra, triangular and crystallographic shaped Frank loops, although fewer in number, have always been observed in quenched and aged gold.19798 It is not known definitely whether these loops form from collapsed tetrahedra. The fact that the Frank loops are usually larger than the accompanying tetrahedra might indicate that the loops grow independently by absorbing vacancies, but this does not rule out the possibility of the collapse of tetrahedra into loops under all circumstances. Silcox and Hirsch1 have actually observed under the electron microscope tetrahedra collapsing into loops, probably due to stresses set up by the heating of the specimen by the electron beam. The energy residing in the stacking faults of a tetrahedron is proportional to the square of the edge length, while the energy of a triangular perfect dislocation loop depends on its edge length, L, as const L ln(L/ro). Therefore, beyond some critical size tetrahedra must become unstable with respect to collapse into triangular loops.1,3,8-11 However, it seems that in the absence of strong stresses tetrahedra usually decay by the

Jan 1, 1969