Search Documents

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By Francis S. Kendorski

Caving offers the lowest cost per ton of ally large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently-taken on new importance as deeper, lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface mining methods, and too low grade to support any type of underground mining except a bulk method such as caving.

Jan 6, 1978

By J. O. McCaldin, P. Duwez

ALLOTROPIC transformations between 1000° and 1900°C have recently been reported for several metallic elements. Since the proposed transformations are based on limited evidence, it was decided to examine the elements in question as well as some refractory metals by thermal analysis with a photoelectric technique similar to that described by Hug-gins, Roll, and Udin.1 In this method, a lead sulphide cell was used to detect thermal radiation from an electric-resistance heated strip specimen. A thermocouple spot welded to the specimen was used to calibrate the temperature of the system under steady temperature conditions, and recording was accomplished with a cathode ray oscilloscope. In the method used by the present authors, the temperature calibration was omitted and the cathode ray oscilloscope was replaced by a recording galvanometer. This technique, in which electric current passing through the specimen heats it, will be referred to henceforth as Method 1. Another arrangement was required for those cases where the specimen could not be formed into a wire or strip suitable for resistance heating. In such cases the specimen was a sintered compact heated by thermal radiation from a hot tungsten strip, Fig. 1. The specimen was insulated from the heating strip with a thin layer of thoria powder or suspended on 0.004 in. tungsten wires. The take-up spring had just sufficient tension to prevent buckling of the heating strip due to thermal expansion. This technique will be called Method 2. Both methods were tested with specimens of iron and titanium and the well known allotropic transformations, a toy and ? to 8 in iron and a to in titanium, were very clearly detected. Fig. 2 shows one of the records obtained for titanium. For this particular experiment, the iodide titanium specimen was a square rod 0.080 in. on an edge and 3 in. long.

Jan 1, 1955

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By AIME AIME

T HE Institute of Metals Division and the Iron and Steel Division will meet jointly at the Stevens Hotel, Chicago, during the week of the American Metals Congress, Sept. 22-26. The Iron and Steel Di- vision of the American Society of Mechanical Engineers, the American Society for Steel Treating and the American Welding Society meet at the same time. but the sessions have been arranged to conflict as little as possible. A rich program of papers and plant visits has been arranged for the members and guests of the two Institute Divisions. The annual dinner and a pro- gram of entertainment are being arranged by the Woman's Auxiliary of the Chicago Section. Members are urged to register immediately up011 arrival and to make dinner and plant visit reservations at the same time.

Jan 1, 1930

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1942

Discussion of the paper of WALTHER MATHESIUS, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 539 to 555. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-This paper answers. partly the difficult questions which have come up as to why it is not economical to use higher blast temperatures in the smelting of Mesaba ores, such as the high temperatures used in European practices, and the answer is very plain that the ores will not stand the higher temperature. But the paper does not go into detail as to what special difficulties were found with the higher temperature of blast, and I would ask the author to kindly specify them. W. A. FORBES, New York, N. Y.-A large part of the troubles that furnace men experienced in using high-blast heats in smelting Mesaba ores in the early days of using Mesaba ores, was clue to the attempt to use these soft ores on furnaces having the same lines as the furnaces used in smelting the hard Old Range ores. As the result of observation and study, the dimensions of the lower part of the blast furnaces have been changed and the difficulties of the blast-furnace men in operating with a large percentage of Mesaba ore and high-blast temperatures have been largely overcome. The changes I refer to in particular are: (1) steepening the angle of the bosh; (2), decreasing the height of the bosh; (3) increasing the diameter of the hearth. JOSEPH W. RICHARDS.-Mr. Forbes's answer is quite satisfactory, and the moral which it points is that when the furnace is run with a higher temperature in the smelting zone, the furnace lines which were adapted for the lower temperatures are not necessarily those best suited for the higher hearth temperatures. If. enriched blast were used in a furnace, and higher temperatures run, it would be found necessary to further modify the lines of the furnace to meet the new conditions and to get the maximum output with economy. J. E. JOHNSON, JR., New York, N. Y.-It seems to me this is one of the few papers which could well have been a little longer. The data which Mr. Mathesius has given us, I think should be considered in connection with the paper which Mr. Brassert read before the American Iron and Steel Institute last spring, in which he described how they had obtained remarkable results with furnaces with steep but very short boshes; the angles have been raised to 80°, and the boshes made so short that they no longer appear as a conspicuous part of the shape of the furnace.

Jan 5, 1915

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a&apos; phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a&apos; phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.&apos; Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a&apos;, with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a&apos; phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a&apos;. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of&apos; CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K&apos;. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer&apos; has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74&apos;5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .&apos;&apos; Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.&apos;jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1&apos; for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

By William Victor Vietti

West Texas and New Mexico have been overshadowed by the dcvelopment in East Texas to such an extent that the area has been placed on a settled production basis by most of the operators. Considerable develop-mCnt work on both proven and unproven acreage remains to be carried 011, but the incentive, a ready and profitable market, has been lacking. The main characteristics of the fields in this area are so well known that they are not described again in this paper, which thus resolves itself into a statistical review of the more important production features of the area. Proration has been in effect during the year and has been rigorously applied with the full cooperation of all producers. Proration in West Texas and New Mexico is based in the more productive fields on a potential and acreage distribution of the allowance to the individual wells or acreage units. Potentials are determined generally by a short production test of from 1 to 4 hr.; and the hourly rate is multiplied by 24 to obtain the 24-hr. production or rated potential of the separate wells. The potential values thus set up have been questioned by many production men who are not willing to concede that the instantaneous (hourly) capacity of a well to produce is its potential capacity for a day with all other wells in the pool producing at their capacity. However, the potential of a well determined as above remains its chief rating as a measure of the permeability in place and as an indication of the possible reserve feeding that well. The acreage factor has made it unnecessary to overdevelop properties in order to obtain an allowance proportionate to neighbors who are willing to drill an excessive number of wells on a piece of acreage in the hopes of a quick drainage and a corresponding profit. Proration has resulted in an orderly development of many of the pools in this area on the base as outlined above, resulting in more reasonable spacing of wells and the more even withdrawal of oil and the ensuing expectation of high recoveries. Big Lake.—Production from the shallow or 3000-ft. pay at Big Lake totaled a little more than 3,000,000 bbl. during the year, and we may expect a smaller recovery for 1933. The deep or Ordovician production

Jan 1, 1933

By Samuel D. Warriner

(Wilkes-Barre Meeting, June, 1911.) THE dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has- been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able not only to reach decisions based upon the merits of the controversies, but to enforce its decisions upon both the employees and the employers. It has never been obliged to shape its conduct to secure the consent of the contending parties, and its decisions have been strictly and, in the main, cheerfully observed. The remarkable feature of this board has been that it has

Aug 1, 1911

C. W. WASHBURNE, New York, N. Y. (communication to the Secretary *).-We are indebted to Mr. Pack for his detailed description of a rapid method of estimating the oil reserves in large fields. Although his method will give only a rough approximation of the reserves, nevertheless it is much more reliable than the saturation method. The saturation method should not be used when any other method is available. The paper describes a generalized method, which is especially useful in estimating the total resources of a Nation or State. Properly it is a method of estimating the oil that can be extracted by common methods within a given period of time. It does not account for

Jan 10, 1917

By Wallace Ralston

The East Texas district includes the northeast 38 counties of the State of Texas. It still remains one of the most important oil-and-gas-producing areas of the United States, since it includes within its boundaries the large East Texas field. Other fields of importance are: Van, Rodessa, Talco, Cayuga, Long Lake and Sulphur Bluff. Production is from the Nacatoch, Blossom, and Woodbine of the upper Cretaceous and the Paluxy and Glen Rose of the lower Cretaceous. Of these, the Woodbine is the most important, since it is the producing horizon iri the East Texas field. Fields East Texas Field.—There were 2471 oil wells, 1 gas well and 84 failures completed during the year of 1936 in the East Texas field; that is, 1565 fewer than in the year of 1935. The total number of producing wells is now 22,031, of which 50 are temporarily shut down; 18,435 wells flowing their production; 3150 pumping; 293 on gas-lift, and 82 operated by other methods. This shows an increase of 1642 wells on artificial lift over Jan. 1, 1935. The average daily salt-water production is estimated at 42,700 bbl. from 2327 wells—an increase of 1201 wells over the year of 1935. The field is now drilled to an average density of one well to 5.85 acres. Average bottom-hole pressure has dropped from 1193 Ib. to 1168 lb., approximately 1 lb. drop for each 6,600,000 bbl. of oil produced. During the month of December 1936, the estimated daily average production of illegal oil had dropped from 20,500 bbl. in December 1935 to 7500 bbl. The commercial gas production is of minor importance in the East Texas field, and figures for the amount of gas taken from the field are not available at the present time. Talco Field, Titus and Franklin Counties.—The discovery well was drilled by Housh, Thompson et al. on the C. M. Carr tract and completed in March 1936, as a pumping well making 552 bbl. per day of 24&apos; gravity oil. This well was first completed at a total depth of 4208 ft., the top of the sand being 4190 ft. Later it was deepened to 4260 ft., which increased the production from 552 to 725 bbl. per day. This field is producing

Jan 1, 1937

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require addi-tional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894° to 898° C. The dissociation of dolomite and magnesite, although studied by several investigators, 4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the