Search Documents

By W. G. Whildin

This paper will be confined to a discussion of the methods in use in the property of the Lehigh Coal & Navigation Co. in the Panther Creek valley. Only the methods used in mining the Mammoth vein will be .considered, as the methods in use in the smaller veins are adaptations of the same. Typical cross-sections of the coal basin are shown in Figs. 1, 2, and 3. The Mammoth vein varies in thickness. It is 21 ft. at one colliery, 50 to 125 ft. at another, and over 200 ft. at still another. Its normal thickness is 35 to 40 ft. At some points in the Panther Creek basin the Mammoth vein is made up of three splits-the Bottom, Middle, and Top, while in other portions the dividing strata between the benches amount to only 1 ½ to 2 ½ ft., and the vein is practically in one. The section of the Mammoth vein shown in Fig. 4 was taken at the Greenwood colliery, and shows a thickness of 60 ft. The miners know it by benches, as follows:. The Three-Foot, the Four-Foot, the Eighteen-Inch Slate, the Bony, the Grey Slate, the Grain Clear, the Five-Foot, the Seven-Foot, the Slaty or Dirty benches, the Blue Slate, and the Top bench. The present-day methods of mining are an outgrowth of the experiences of the last 100 years in this territory. The first attempt at mining, according to the company's maps, was made at Summit Hill in 1792, when open cuts and pits were made. Later the pillar-and-breast method was introduced. This and other methods will be discussed hereinafter. Drifts, slopes, and shafts, according to the requirements and physical conditions, are the main openings, from which the gangways are driven. The gangways (haulageways) and airways are driven along the strike of the vein; the gangways in the various veins on the same level being connected by tunnels through the intervening rock. The gangways and airways in thick veins are heavily timbered ;throughout. The sets of timber, consisting of a collar and two legs, are spaced 5 ft. apart, and later, after the ground :has settled, additional sets, called "liners" or "relief sets," are placed between, to relieve the strain on the original timbers, so that the result is a set of timber every 2 ½ ft.

Jan 12, 1914

By W. H. Hoffman

During the autumn of 1891, several heavy blasts (each throwing down some 3000 tons of ore) were made on what is known as the Theall side of these mines. Immediately after one of these blasts, the writer found that at least one-third of the ore was largely impregnated with pyrites, and besides this, fully 15 per cent. of the entire blast was composed of irregular lumps of magnetic pyrites. This was a revelation wholly unexpected, as previous examinations by many experts had failed to disclose any such quantity of sulphury ore. Over the center of the Theall tunnel there suddenly appeared a perfect keystone, as it were, of pyrites, 3 feet wide at the arch of the tunnel, 13 feet ride at the top, and 20 feet high. This keystone pinched out in February, 1892; but in that month large blocks of pyrites were more plentiful on or near the western wall, and these deposits extended the entire height of the workings, some 43 feet. The second blast in November, in the face and over, and on each side of the tunnel, was far more surprising. The whole cross-section it exposed was thickly interspersed with layers of magnetic pyrites, ranging in thickness from 10 to 24 inches, and quite irregular in form, while all of the ore carried much more than the usual amount of sulphur in the non-magnetic pyrite. One hundred and fifty-five tons from a portion of this breast (western side), showed the following composition upon sampling and analysis: Per cent. Metallic iron,...45.080 Phosphorus,..........304 Sulphur,...........23.510 And the balance of the blast showed: Per cent. Metallic iron,.....• 33.210 Phosphorus,...........349 Sulphur,.......... 6.680 vol. xxI.-33

Jan 1, 1893

By J. Chipman, N. J. Grant, B. M. Shields

The vacuum tin-fusion method of analysis for hydrogen, developed by Carney, Chipman, and Grant, has been modified to permit the analysis of the evolved gases for hydrogen by means of a thermal conductivity cell. A properly prepared sample can be analyzed in 10 min with a probable error of ±0.12 ppm. A study of various methods for storage of hydrogen samples shows that samples can be safely held in a dry ice-acetone bath as long as six days. Storage in liquid nitrogen is necessary for samples to be held one week or more. HE vacuum tin-fusion method, as developed by I- Carney, Chipman and Grant,' is the only analytical procedure which has shown promise of being fast enough for use in the control of hydrogen during steelmaking. It was felt that further simplification and faster speed of operation could be effected by the use of thermal conductivity measurements for analysis of the gases evolved in the tin-fusion method. The application of conductivity measurements to the tin-fusion method is possible because: 1—the evolved gas is essentially a mixture of hydrogen, nitrogen and carbon monoxide with a hydrogen content usually over 50 pct, 2—the evolved gas is collected at a relatively low pressure, and 3— the thermal conductivities of CO and N2 are practically identical while that of hydrogen is very much greater. The major part of this research program was devoted to the construction and calibration of a vacuum tin-fusion apparatus which analyzes the evolved gases for hydrogen by means of a thermal conductivity cell. The second phase of the problem was associated with the development of a procedure for storage of samples prior to analysis. With the rapid quenching method for hydrogen sampling,' which seems to be the most practical for steel mill use, it is necessary that the samples be stored safely during the interval between sampling and analysis if the hydrogen content of the molten metal is to be maintained in the supersaturated solid samples. The thermal conductivity bridge has been used for a number of years in the analysis of certain gas mixtures. An elementary discussion of the theory and practice of gas analysis by thermal conductivity measurements is given by Minter.3 A more comprehensive discussion of the theory and of the various measuring circuits is presented by Daynes.' A complete knowledge of the theory and properties of the thermal conductivity of gases and gaseous mixtures can be gained by a study of the standard textbooks on the kinetic theory of gases."' The existing data on the thermal conductivity of single gases are reviewed by Hawkins: that for a number of binary gas mixtures by Daynes' and Lindsay." The thermal conductivity method may be applied to the determination of the composition of a binary mixture if: 1—the thermal conductivity of the mixture varies monotonically with composition, and 2— the two gases have measurably different thermal conductivities. The greater the difference between the two gases, the greater the sensitivity of the method.10 he method is applicable to the analysis of multicomponent mixtures when all of the gases in the mixture except one have nearly the same thermal conductivity. Fortunately, the mixture of hydrogen, nitrogen, and carbon monoxide evolved by the tin-fusion analysis' falls in this latter classification. The thermal conductivities of nitrogen and carbon monoxide are practically equal; and the thermal conductivity of hydrogen is approximately seven times that of the other two. Therefore, the thermal conductivity of a gaseous mixture of hydrogen, nitrogen, and carbon monoxide at known temperature and pressure can be related directly to the percentage of hydrogen in the mixture by suitable calibration. Usually the thermal conductivity of a mixture of gases is measured at atmospheric pressure where the thermal conductivity is independent of pressure over a wide pressure range. At very low pressures (below 1 mm Hg), the thermal conductivity of gases varies with the pressure. This phenomenon has been utilized in the Pirani vacuum gage for the measurement of pressures in the range of 10" to 10-0 mm of mercury.= Very little has been published concerning the variation of thermal conductivity with pressure at intermediate pressures between 1 mm Hg and 1 atm. However, preliminary measurements indicated that the thermal conductivities did vary with pressure over the range of pressures (up to 10 mm Hg) at which gases are delivered from the vacuum pump. Therefore, the calibration of the thermal conductivity cell had to be planned to include the effects of both gas composition and pressure. Such a calibration chart is shown in Fig. 4. Most industrial applications of the thermal conductivity method of gas analysis have used a compensated Wheatstone bridge circuit containing two

Jan 1, 1954

By Paul A. Beck, M. N. Parthasarathi

By determining the (220) pole figure for OFHC copper rolled to 96 pct R. .A., the occurrence of four texture components of the type (135) [211] was confirmed. It was found that the total volume fraction of material close to the four symmetrical orientations of this type is larger than the volume fraction of the other components put together. THE rolling texture of copper was described by early investigators1'" as a mixture of components of the (110)[l12] and (112) [11l] types. Other studies, still using the qualitative photographic method of texture determination arrived, instead, at orientations of the type (135) [533] or (135) [211] for copper3'4 and at the closely related "Z-texture" for a fee nickel-iron alloy.5 The prevalence of this type of orientation, near (123) [412], in the rolling texture of aluminum and of copper was later confirmed by means of quantitative diffractometer methods.' However, in a recent paper7 Jones and Fell stated that the (110) [112] and (112) [111] double texture was in better agreement with the measurements of Young's modulus for cold-rolled copper.' These authors also expressed their belief that the "roll texture" can be determined by means of two photographic quasi-fiber texture patterns taken with sheet specimens rotated around the rolling direction and the transverse direction, respectively. Jones and Fell found7 that the results obtained from such patterns for cold-rolled nickel did not agree with any of the orientations mentioned above, but they suggested that the observed diffraction spots may have been brought about by the overlapping of reflections due to the (110) [112] and (112) [11l] double texture components. Jones and Fell concluded that the (123) 14121 type orientation is inconsistent with their patterns. They also stated, without offering any supporting evidence, that this orientation is inconsistent with the (220) pole figure. "Ideal orientations" are often used for a very rough description of the principal orientations encountered in a texture, It is, however, well to remember the fact that, no matter how "accurate", these ideal orientations are only schematic representatives of a continuous distribution9, which often (as in the case of rolled copper) includes extensive orientation spreads. The attempt by Jones and Fell7 to use elastic modulus data in deciding between various ideal orientations in the rolling texture of copper neglects this fact. The inadequacy of two-dimensional "axis density figures" in describing orientation distributions in sheet textures was previously discussed.9 It was also pointed out9 that there is no reliable evidence to prove that orientation distributions derived by the "quasi-fiber method" from rotated sheet specimens are fully equivalent to the corresponding information obtainable from quantitative pole figures. The view that a sheet texture could be adequately determined by means of two photographic quasi-fiber texture patterns is obviously erroneous9. The question as to the consistency with the (220) pole figure of ideal orientations derived from the (111) and (200) pole figures is, on the other hand, certainly very relevant. Since no quantitative (220) pole figure for cold-rolled copper appears to be available in the literature, the following work was undertaken. EXPERIMENTAL METHOD An extruded rod of OFHC copper, 1 in. in diam, was given alternate rolling (30 to 35 pct R.A.) and

Jan 1, 1962

By R. A. Wagstaff

Since the time of the early Egyptians, the use of copper: has been a boon to the life of most of the civilized world. Its use has been varied; in many connections, the art by which it attained its greatest usefulness has been lost. In this paper an endeavor will be made to take into consideration some of the many changes that have occurred during the last 40 years of copper-smelting operations. During that period the copper blast furnace has been almost forced out of existence by new methods of ore concen-tration—first, gravity concentration, and then flotation. These new methods of concentration introduced many new factors into the metallurgy of copper. The product was wet, it was fine and it was high grade. To overcome all these factors many changes have been necessary throughout the smelting agenda. New equipment has been necessary for transportation, unloading, sampling, bedding and moisturing in all smelting plants, especially the custom smelter' During the early days of "flotation," little was known about filtering or the use of an alkaline circuit; often the concentrate going to the smelter contained 2' to '5 Per cent moisture. It is easy to imagine the difficulty arising with a product of this nature when it had to be shoveled by hand labor. To meet these conditions, mechanical unload- ing and sampling devices were soon developed. In many instances such good progress was made that actual costs for handling this unfavorable product were lower than those formerly incurred on the old product. Today most sampling of copper ores and concentrates is being done by mechanical sampling, pipe or augur sampling, or shovel sampling. Where concentrates are uniform in metal content, a great many of the plants now use pipe or augur sampling. For spotty ores, the old shovel sample with cone and quartering during the final stages is still in' use. Where big tonnages are handled, mechanical sampling of concentrates is being done, with satisfactory results. To curtail slow and tedious cutting and mixing procedure, mechanical mixing boxes, splitters and cutters are used to cut down labor costs. Milling As crude ores become scarcer, the use of milling operations increases. The few crude ores that are still smelted are used as fluxing types. To use these ores finer grinding has been found advantageous. This has made for better bedding and fluxillg conditions, which in turn makes for faster smelting, lower fuel consumption and better metal recovery. The degree of fineness is more or less determined by the nature of the product. Most plants have set a standard of through 3/8-in. mesh screen for roaster -reverberatory smelting and through 3/4-in. mesh screen for converter fluxes. For some refractory Ores, even finer grinding has been found to be advantageous for good reverberatory smelting-

Jan 1, 1944

By A. D. David

The object of this paper is to reduce to the simplest possiblc discussion the recent developments in refinery technology without resorting to detailed technical descriptions of the various items. During the year 1929, the most noteworthy tendencies have been towards the installation of more flexible plants, more unified operations, more balanced performance and greater fuel economy. In no other year in the history of petroleum refining has the industry witnessed to as great a degree the crystallization of so rnany developments in almost every phase of the art. Economic pressure has been the controlling factor, supplemented however by a market demand for more volatile anti-knock gasoline and higher quality of lubricating oils, resulting from the extended use of high-compression motors. Catalytic Hydrogenation Possibly the outstanding achievement during the year has been the beginning of construction of plants by the Standard Oil Co. of New Jersey for the catalytic hydrogenation of the so-called heavier and inferior petroleum oils to produce therefrom not only high yields of anti-knock gasoline, but also lubricating oils equal in quality to the best grades obtainable. It is reported that the plants will operate at a pressure of 4000 lb. or higher and temperatures in excess of 900" F. will be used. The hydrogen required for the conversion will be produced from refinery gases. This type of processing will doubtless be an important factor in balancing future operations; in other words, it can be used to eliminate present waste products and permit production of high-grade products from low-grade crude. Improvements in Lubricating Oils Another important development during the past year has been the extended use of vacuum stills, making possible the production of lubricating oils from what was formerly classed as "fuel-oil crude," or crude from

Jan 1, 1930

By Arthur Knapp

The ordinary well log is subjected to a great deal of criticism, much of which is well founded. Sometimes, though, the difficulty in interpreting the log is due to the fact that the geologist or engineer using the logs does not know the limitations of the drilling method used. The rotary drill, especially, has inherent limitations that make it difficult to secure definite information at all times. The identification of well-defined key beds is about all that can be expected from the rotary log. The formation in a drilled hole, as reported by the driller, has a direct relation to the speed with which the drill makes the hole or to the reaction of the various strata on the bit, called the "feel of the bit." When this is not thoroughly understood by the geologist or engineer endeavoring to interpret the log, the result is an erroneous correlation with other wells or a discarding of the log as worthless. General Terms Hard and Soft.—Hard and soft are relative terms. In the case of well logs, they are very misleading as they are used in connection with both resistance to abrasion and resistance to percussion. In technical rock classification, hardness is relative resistance to abrasion. The term brittleness is used in connection with resistance to blows. These terms are misleading to the geologist or engineer who is not familiar with both the cable-tool, or standard tool, method of drilling and the rotary method. In the case of the standard tools, the driller's report of the hardness of the formation is in terms of its resistance to blows. For instance, a cable-tool driller might be able to make from 30 to 50 ft. a tour in a brittle limestone, which he would call soft and at the same time he might call a relatively soft (from a purely mineralogical standpoint) gypsum hard, because it is somewhat elastic and is not readily broken by blows. The rotary driller would reverse the terms. The limestone is hard in that it resists the abrasive action of the bit, while the gypsum might be soft in that it is readily cut by the rotary bit. It is rare that wells drilled by the standard tools are correlated with those drilled by the rotary, but the technologist who has worked with well logs from one system might be misled when working with the other.

Jan 1, 1921

By D. Van Winkle, C. Zener, H. Nielsen

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By C. Zener, H. Nielsen, D. Van Winkle

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970

By AIME AIME

NOTWITHSTANDING the metropolitan appearance of M. L. Haider, the present Chairman of the Petroleum Division, he is not a native New Yorker, but was born at Mandan, N. Dak., Oct. 1, 1904. He began his travels at an early stage in life and after attending the University of Southern California for two years he spent two additional years at Stanford University and was graduated in 1927. After a few months as an analytical chemist for the Portland Cement Co. he became research engineer in the natural gasoline department of the Richfield Oil Co. where he remained for approximately two years before taking a position with the Carter Oil Co. in Oklahoma. He was chief engineer for this company for three years before being trans-

Jan 1, 1945

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By F. D. DeVaney

IT is of great interest that the various organizations engaged in the search for a cheap and efficient agglomeration process for fine magnetite concentrates-essential if the taconites are to be utilized-have ended up with processes that are basically different. This paper describes the development and the present status of the shaft-type furnace as now utilized by the Erie Mining Co., which is managed by Pickands Mather & Co. The shaft furnace has always had an appeal to metallurgists because of the simplicity of the design and the possible low fuel consumption. Work done on pelletizing at the University of Minnesota Mines Experiment Station by E. W. Davis and his associates determined that it was possible to roll up fine magnetite concentrates in a balling drum, and that, if such balls were fired at a sufficiently high temperature, a hard, indurated pellet, well adapted for use in a blast furnace, could be made. Early furnaces had no heat recuperation and the heat consumption was in the order of 2 million BTU's per long ton.

Jan 3, 1958

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

It is too late to gloat over the fact that minerals have furnished 67 per cent of the primary wealth of Pennsylvania. It is high time that Pennsylvanians do some constructive thinking in terms of the present and future with regard to the remaining mineral heritage.1 The discovery of a deposit of pyrophyllite in the South Mountain region of the Cumberland Valley indeed emphasizes the increased importance of a more exact inventory of the metal and mineral resources of Pennsylvania. Active geological work and research have been in progress for many years, but the surface has been little more than scratched. The results obtained thus far in survey and research have been extremely beneficial to the Commonwealth and a fundamental hub of its industrial development. But these activities are wholly inadequate in the face of rising demands for the future. The need for an accelerated program to continue a study of Pennsylvania's mineral resources on a more intensive scale was never more acute.2 In part, this has been caused by the insatiable demands of industry. It has been caused also by wasteful use and ignorance.

Jan 1, 1950

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.'

Jan 1, 1964