Search Documents

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By J. J. Carrigan

DURING the experimental stage in our use of the electric cap lamp in the Anaconda mines at Butte. Mont., we were somewhat concerned as to how the spitting of fuses would be carried out if we completely eliminated the open-flame light. This problem was at once given serious attention by the engineering research department and some thought was given to having all blasting done by the use of electric delays, which has been the practice for some years

Jan 1, 1936

By William Y. Holland, Roger H. Cook

Dexter H. Reynolds (Chapman and Wood, Mining Engineers and Consulting Geologists, Albuquerque, N. M.)—A number of questions are raised by conclusions and inferences made in the above-mentioned paper. The more troublesome of these concern use of the various pozzolans to combat the deleterious effects of the alkali-aggregate reaction. The most alkali-reactive materials listed are opal and rocks containing opaline silica. The pozzolans mentioned specifically for use as amelioratives are opaline shales and cherts. These are stated to retard the expansion caused by the alkali-aggregate reaction. Another well-recognized pozzolan is diatomaceous earth, which consists principally of opaline silica. A pozzolan presumably owes its effectiveness to its high reactivity with the alkaline liquid phase of the concrete mix. It appears reasonable to expect that finely divided opaline silica added as a pozzolan would be more susceptible to reaction with the alkalies present than would larger particles of the same material. The authors report that work with high and low alkali cements indicates that in the presence of alkali-reactive materials, deleterious expansion depends upon the alkali content of the cement. The total effect, therefore, should be more or less independent of the amount of reactive aggregate present, and still more independent of its state of subdivision. The deleterious effects should, if anything, be aggravated by the addition of a finely divided, highly reactive pozzolan. Further, if the alkali-aggregate reaction is of great importance in the long-term soundness of concrete structures, the addition of a pozzolan to a concrete made with aggregate free from known deleterious materials would be a questionable procedure. The benefits reportedly accruing from such use of pozzolans are greater ultimate strength for a given cement content, increased resistance to deterioration by exposure to sulphate solutions and other mineral waters, and greater resistance to damage by wetting and drying and freezing and thawing. In view of the deleterious effects of highly reactive materials are these benefits ephemeral? The same considerations apply to another alkali-reactive material, chalcedony, which appears to consist of ultrafine-grained quartz, with opal absent in detectable amounts. Quartz flour is notably reactive chemically and physiologically (cf. Ref. 11 of Holland and Cook's paper), a fact borne out by its effectiveness as a pozzolan, which presumably might be expected to offset the deleterious effects of the presence of chalcedony in the aggregate. A second question of some importance concerns the reportedly highly deleterious reactivity of acidic and intermediate volcanic glasses, such as rhyolite, perlite, and pumice. Air entrainment is listed as one of the ameliorative measures to combat the deleterious effects of the alkali-aggregate reaction. The alkalic-silica gel formed by the reaction may expand into air bubbles and thus not cause appreciable expansion of the concrete mass. It would appear then that pumice and perlite, particularly perlites of the pumiceous types and other types after expansion, would also tend to counteract the expansion, since these materials consist largely of voids and air bubbles. Certainly this would be expected of structural concrete in which pumice or perlite is used as total aggregate. Finely ground pumice, perlite, and volcanic ash have been demonstrated to be active pozzolans (cf. Pumice as Aggregate for Lightweight Structural Concrete by Wagner, Gay, and Reynolds, Univ. of New Mexico Publications in Engineering No. 5, Albuquerque, 1950). In fact, the term pozzolan was first associated with finely divided pumice or volcanic ash. Such materials were used with hydrated lime as the sole cementitious agent in constructing public buildings, roads, and aqueducts by the ancient Romans. The deleterious alkali reactivity of the volcanic glass, itself containing several percent of the alkalies, apparently did not contribute to the remarkable state of preservation of those ancient structures, as exemplified by the Appian Way and the Pantheon Dome. Still a third question involves .the reactivity of constituents of concrete when exposed to various salt solutions. Resistance to. deleterious expansion and cracking as a result of contact with mineral waters and its relationship to the mineral content of the aggregate are not mentioned by the authors. Yet the phenomena pictured in Fig. 1, and especially in Fig. 2, appear very much like those caused by exposure to mineral waters. The deterioration of concretes exposed to sulphate waters is generally considered related to the chemical constituency of the cement itself, particularly to the relative amount of tricalcium alum-inate contained. Could not many of the ill effects presently blamed on alkali-aggregate reaction really have been caused by contact with sulphate or other salt-containing mineral waters? Or perhaps their use as mixing waters? May not the deleterious expansion be as much a function of the chemical makeup of the cement as it is of the mineral constituency of the aggregate? Would it not be just as important to use alkali-free mixing water as it is to use a low-alkali cement? It appears obvious that resistance of cements and concretes to sulphate and other salt solutions cannot be left out of account in discussion of deterioration of concrete structures with time. This factor may be of equal or even greater importance than the alkali-aggregate reaction, particularly for concrete subjected to wetting and drying cycles, such as airstrip paving, water-retaining dams, and highway structures. Another very important factor is called to attention on page 1022 of the article in Mining Engineering, October 1953, in that failure of concrete structures may result from poor construction practices and use of too high water-cement ratios. Both of these can contribute remarkably to decreased resistance to attack by sulphate waters, and presumably could have an equally remarkable effect upon extent of damage resulting from the alkali-aggregate reaction. From the above remarks it appears that while alkali-aggregate reaction may be an important factor in decreasing the useful. life of a concrete structure, it is not the only factor involved, and it may not be even a controlling factor. Likewise, many of the phenomena apparently associated with the alkali-aggregate reaction may have resulted from cond'itions which had little relationship to the alkali-reactivity of a constituent of the aggregate. Certainly if alkali-aggregate reactivity is a major factor in bringing about early failure, one cannot help feeling anxiety concerning the future of the many concrete structures in this country and abroad in which pumice and perlite were used as total or partial aggregates. This anxiety can only be dispelled by calling to mind that among the best-preserved relics coming down to us from ancient times are structures made with mortars containing highly alkali-reactive aggregates.

Jan 1, 1955

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1'2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger' on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.' This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1' were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963

By Scott Turner

OUR Institute, in its annual Directory, states the following: The purpose of each Technical Committee is to further the development of the special mineral industries in its field, chiefly through obtaining and discussing papers suitable for publication by the Institute. The proper field of the new Health and Safety in Mines Committee is judged to include the entire mining industry, and involves the multitude of health and safety problems arising in all kinds of mining operations. The mining industry in the United States has made much progress during recent years in reducing accidents. This advance has been widespread, and has been especially notable in the mining of iron ore. Yet the statistics of the U. S. Bureau of Mines, when compared with figures of the National Safety Council for other industries, show that mining still has a higher personal mishap rate than any other major industry in this country. In addition, studies of dollars-and-cents cost of casualty occurrences indicate that an important part of our mining cost, held by various authorities to be as much as 10 per cent of the total, is due to accidents.

Jan 1, 1933

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

By C. Erb Wuensch

The Eagle mine is situated in the Kerber Creek mining district, Bonanza, Saguache County, Colo. The climate and topography of this district arc similar to those of mining camps of the Rocky Mountain region that lie 9000 to 12,000 ft. above sea level. The district is at the northeasterly edge of the San Juan volcanic region, in which successive Tertiary lavas have built up a high plateau resting upon earlier sedimentary formations, or the underlying pre-Cambrian complex. The latter was exposed in places by erosion previous to the eruptions. In the Bonanza district, proper, only volcanic formations, andesites and latites, are found. Dr. H. B. Patton,1 in his survey of the district, discriminates between several varieties of lavas and maps these as distinct flows. They are local variations within the same lava and it is impossible to determine any distinct line of demarkation between them. Structurally they are members of the same flow. There are three general types of vein occurrences: 1. Lead-zinc-copper-silver-gold veins in well-defined fissures with a quartz gangue; ill these, the various sulfides show a zonal arrangement. 2. Massive gray copper ores high in silver, in irregular fractures in the form of small lenses and pockets, in which little or no quartz is found. 3. Manganiferous quartz veins very low in silver and gold at the surface which, with depth, become important silver veins containing subordinate amounts of gold. These veins have a quartz gangue with an abundance of Phodochrosite. The silver is associated with small amounts of sphalerite, galena, and pyrite; fluorite also is present. The Eagle is the only mine that has been developed in the manganiferous quartz type of vein. It was discovered ill the fall of 1582, but little more than assessment work was done on the property for a number of

Jan 1, 1923

By Charles Catlett

The terms " developed " and " undeveloped " are necessarily relative and cover a wide range; but the latter is here applied to cases in which the information at hand falls short of a clear demonstration of values, and conclusions must be reached frorn a study of the geological conditions of the particular deposit, interpreted in the light of similar and closely-related deposits. Such an inquiry might be characterized as an effort to reach reliable conclusions from insufficient data. But the engineer

Jan 1, 1909

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By L. Russell, van Wert

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By van Wert, L. Russell

During an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. Cleavage Structure in Heat-treated Muntz Metal Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decornposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions— austenite and quenched Muntz metal— are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent. gamma iron, at ordinary temperatures is below its normal stable range whereas the metastability of the quenched Muntz metal is the result of supersaturation. When a 60:40 brass is quenched from above 800" C.—that is, from within the field where the beta phase alone is stable—this solution is retained practically intact and the alloy so cooled is found to consist almost entirely of polyhedra of this solution with only a little alpha present ordinarily at the boundaries of the beta grains—the result of a slight

Jan 1, 1929

By G. W. Elger, H. E. Bell, J. E. Tress, J. B. Wright

This paper describes laboratory techniques and subsequent results of US Bureau of Mines (USBM) research to produce chlorination-grade feed- stock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau effort to devise technology that may help decrease US dependence on imported raw materials. A rock ilmenite containing about 46 wt % TiO2 was smelted in an electric arc furnace with coke, wood-chips, and Na2CO3 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slug. The slug was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1-kg/h (10- to 20-lb per hour) apparatus at 1023° to 122J0 K (1380° to 1740° F). The sulfated slug, containing 60% to 65% TiOb, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome calcium, magnesium, and manganese impurities from 7.0 to 1.7 wt 70. The final product was upgraded to about 8.4 wt % TiO2. This material is potentially suitable for chlorination in a fluidized bed reactor. The most favorable results were achieved with leached slug sulfated at a feed rate of 4.5 kg/h (10 lb per hour) and at temperatures of 1073° to 1123° K (1470° to 1560' F).

Jan 1, 1986

TWO very interesting sessions on mine ventilation were held on Monday. George S. Rice, chairman of the Mine Ventilation Committee, presided at the morn-ing session. Formal reports from two subcommittees were presented, as well as two technical papers. Daniel Harrington, for the subcommittee on metal mining, gave a most interesting report, devoting most of it to a review of the literature that had appeared during the past year, to the cooling of mine air, and to a discussion of mine fires. In the absence of Dr. R. R. Sayers, chairman of the Physiological subcommittee, Mr. Harrington gave a resume of that report. The main points covered were in connection with silicosis but some attention was also paid to the associated prob-lems of air cooling and humidity. The paper by Prof. W. S. Weeks on the "Air-Current Regulator" was briefed by Prof. A. C. Callen. Pro-fessor Weeks brought out the fact that the common application of Murgue's equivalent-orifice formula to regulator problems was incorrect, inasmuch as the dis-charge from the regulator was not released into the open air but into a slow-moving current beyond the regulator. He applied the shock-loss theory of Bordoni to the problem and worked out a formula for solving regulator problems, giving coefficients of contraction he had determined experimentally.

Jan 3, 1928

By Albert Sauveur

Iron, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.' For this purpose, a cuprie solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free, from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters. which represents the same spot as that shown in Fig. 1. The fillings have been darkened while the axes remain white, the action being, therefore, the reverse of that of cupric reagents. On closer examination, under higher magnification (Fig. 3) it is found that the picrate blackens the small particles of manganese sulfide, that these are frequently surrounded by a rim of white, or relatively white, ferrite, and that both the ferrite

Jan 1, 1924

By George C. Branner

BAUXITE is produced in Arkansas from two mining districts in the central portion of the State. These are (1) the Fourche Mountain district, immediately south and southeast of Little Rock in Pulaski County, and (2) the Bauxite (town) district, about five miles east of Becton in the eastern part of Saline County. These two mining districts are about twelve miles apart, separated by territory which, so far, has produced a negligible amount of commercial ore. Mining was by open-pit methods exclusively until 1924, when underground methods came into use. From 1924 to 1930 about 40 per cent of all of the ore produced in Arkansas was mined by underground methods, mainly by retreating caving.

Jan 1, 1935

By Guillermo Mariaca, Jorge Muñoz Reyer

As far as technology is concerned there has been no development in Bolivia during the year 1936, because the country, just emerging from the war with Paraguay, is only beginning to rebuild its economic foundations. Great steps, however, are being taken in order to secure a rapid and sound development of its oil resources, as follows: 1. The new Petroleum Law, which contemplates the problem of proration and conservation of natural resources, prohibiting the wasteful use of gas, and regulating the number of wells, their spacing and the permissible output per well, for each particular pool according to the conditions prevailing therein. 2. The creation of an official entity with the object of developing and exploiting a large petroliferous area. This entity has been called Yacimientos Petroliferos Fiscales Bolivianos (Y.P.F.B.), and the region assigned to it is all the sub-andean zone, which is approximately one hundred miles wide and borders the eastern part of the Oriental Andean range, from Argentine to Peru. It is said that drilling will be started immediately in various localities. At the present time a wide geological survey of part of the area is being made in order to find out which regions offer the best possibilities of commercial development. Y.P.F.B. has been authorized by the Government to draw up contracts with private companies for the exploitation of limited zones. Production The only company that has been producing in the country in 1936 is the Standard Oil Company of Bolivia, and only from two of its fields: Camiri and Sanandita. New wells were not drilled. During the first nine months of the year 12,762,958 liters (80,275 bbl.) was produced, 34,985 bbl. from the Camiri field and 45,290 bbl. from the Sanandita field. Reports for October, November and December are not yet available. The total for the year 1935 was 25,978,737 liters (163,388 bbl.).

Jan 1, 1937

By O. W. Ellis

THE writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.1 The copper referred to in his in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal, did not measure up to conductivity FIG. L -INGOT OF OVERPOLEP COPPER. standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the Westinghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 ½ in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of overpoling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946

By Carl Altstetter, Roy Adams

Measurements of enthalpy changes and transformation temperatures me reported for the fcc -hcp marten-sitic transformation in pure cobalt single and multi-variant crystals andpolycrystalline specimens. From these measurements the free-energy difference between the two phases was calculated for both heating and cooling and for repeated cycles through the transformation. For heating of single crystals the average value of enthalpy change was 113 cal per mole but on cooling it was 84 cal per mole. This difference is interpreted in terms of lattice imperfections which are introduced during transformation. A calorimeter suitable for measurement of enthalpy changes of athertnal transformations is described. COBALT exhibits an allotropic phase transformation at around 417°C' where an hcp phase (a = 2.507, c = 4.0686, c/a = 1.6228)~ stable at low temperatures transforms to an fcc phase stable up to 1495°C. The transformation has a hysteresis of about 30°C— the exact magnitude of the hysteresis depending on the number of transformation cycles, grain size, impurity content, and prior treatment.'-6 The athermal character of the transformation and surface relief due to transformation shear indicate that the transformation is martensitic. Pole mechanisms for the transformation have been discussed by Sebilleau and Bibrin, Bilby, Seeger,' and Basinski and Christian. These authors have proposed that the cooling transformation is effected by rotation of a Shockley partial dislocation around a pole dislocation with a screw component of 2a/3(111). Such a rotation would change the stacking of close-packed planes from the abcabc fcc stacking to the ababab hcp stacking sequence. This mechanism would predict a lattice correspondence of {111}fcc~~(0002~cp, have been observed. One would expect the heating transformation to occur similarly, involving dislocation movements on the (0002)hcp. However, a high density of pole dislocations and high dislocation ve- locity are required to account for microscopic observations. Furthermore, the high back stress developed on the Shockley partial dislocation as it rotates toward the sessile dislocation associated with it makes it doubtful that this is in fact the transformation mechanism. A mechanism for spontaneous nucleation of partial dislocations1*l2 seems more reasonable. If a single crystal of cobalt is cycled through the transformation but never heated above 600°C, it will remain single."13 However, if the specimen is heated through the transformation and held for a short time at or above 1000°C before cooling, the cooling transformation usually involves all four {lll}fcc habits, resulting in neighboring orientations of hcp differing by 70.5 deg. This condition is termed multivariance and has been observed by Bibring and sebilleau5 and Nelson and ~ltstetter.' The latter authors used single crystals of cobalt grown in an electron beam zone refiner. They proposed that the strongly directional cooling caused the initial cooling transformation to occur on the {lll)fcc most nearly perpendicular to the temperature gradient. Transformation shear on one set of {lll}fcc planes immobilized dislocations on the other {lll}fcc planes involved in the initial transformation. Since there is only one (0002)hcp plane orientation, the product of subsequent heating transformations could have no more than two variants—the original fcc orientation or its twin. If, however, the specimen was annealed at a high temperature, such as 1000°C, there would be relaxation of dislocations into low-energy configurations, and in the absence of a sharp temperature gradient transformation on all four (111 Ifcc planes could occur. If a dislocation mechanism is responsible for the transformation, the perfection of the lattice should affect the reversibility of the transformation. Mutual constraints of neighboring grains in polycrystalline material would inhibit dislocation movement resulting in increasingly sluggish transformation. Indeed, Nelson and Altstetter found the M, to decrease and the A, to increase in going from single crystals to multi-variant specimens to polycrystals. The effect is enhanced by decreasing the grain size of a solid specimen or a powder.6'14 Data on the free-energy difference necessary to initiate the transformation gives information about the driving force of the transformation. This is an important consideration in the understanding of the transformation mechanism. The free-energy change associated with the transformation of the hcp phase to the fcc phase at some temperature T different from the equi-

Jan 1, 1969