Search Documents

By C. S. Matthews, M. J. Fischer

Distortions caused by dip on five-spot sweep pattern were determined by visual experiments on a model composed of parallel plates of glass with holes drilled at the well positions. This model war designed to simulate a reservoir depleted of its primary oil and containing a gas phase. Prior to interference, it was found that the injected fluid took a nearly circular shape about the injection well for the cases studied. However, these circles moved down-dip considerably under the influence of gravity. It was concluded that pattern flooding should be practical for many dipping reservoirs. A quantitative measure is given of how much the well position should be altered to allow for dip. Experimental deternzinarions of injectivity showed this to be about the same in a dipping reservoir as in a horizontal one. INTRODUCTION This investigation was undertaken at the suggestion of the Pacific Coast area, Shell Oil Co., where a pilot water flood in a dipping reservoir was being carried out at the time this paper was in preparation. Prior to the undertaking of this flood there had been considerable speculation as to how gravity would distort a flood pattern in a dipping reservoir. The thought was expressed in some quarters that a five-spot flood would not be applicable to a dipping reservoir because the flood pattern would elongate in the direction of dip and would never form a "seal" around each five-spot. If the flood pattern elongated sufficiently, both the oil and the water might flow largely downdip rather than into the pattern producers. In view of the importance of the California water floods, it was deemed important to determine the effects of gravity on a five-spot pattern in a dipping reservoir. Previous work had also been carried out in this laboratory,1 but only for the single-fluid case. The present investigation extends these results to multifluid cases. Several sets of pictures of flood fronts are presented so that the process can be visualized. From these pictures, curves are obtained which show the correct drilling position for achieving equal times of oil-bank breakthrough. Several injectivity curves are also presented which may aid in prediction of injection rate. ASSUMPTIONS The present results were obtained with a model composed of two parallel plates of glass spaced about 1 mm apart. When the inertial forces are small, as in these experiments, the flow between the plates follows Darcy's law and is analogous to flow through porous media. In using these plates, it is not possible to scale effects of capillarity correctly as regards a transition zone between injected and displaced fluid. Calculations show, however, that effects of such capillarity should not be important in determining the gross flooding pattern in the field. In fact, in this model the capillary forces tend to circularize the pattern to a greater degree than in the field. To preserve a large ratio between the viscous forces and the circularizing capillary forces in the laboratory model, viswus glycerine was used as the flooding liquid and the rate of flooding was very high. The circularizing force is believed negligible in these experiments. In addition to the effect of the surface tension y, which tends to circularize the pattern, another capillary force must be considered. This is the adhesion tension y cos, which acts at right angles to the circularizing term y. If the plates in the model are "wetted" the same all around the periphery, then the adhesion tension,

Jan 1, 1957

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By Herbert Herman, M. E. Fine

THE first decomposition product of a supersaturated aluminum-rich A1-Ag alloy at low tempera- tures is Guinier-Preston zones.'-, The zones are ideal and each consists of a spherical shaped silver-rich cluster about 16 A in diam syrounded by a silver-poor shell approximately 72A in diam.' The composition of the two regions is not known with certainty., After quenching from the solution anneal, these zones form rapidly on aging at temperatures as low as -30°C.5 The rate of zone formation increases with aging temperature; the activation

Jan 1, 1961

By R. J. Blackwell, A. L. Pozzi

Scaled laboratory-model studies provide a powerful method for evaluation of a proposed oil-recovery process. In recent years, models have been used extensively to evaluate processes in which solvents displace oil, both for general cases and for specific reservoir conditions. Since the performance of a miscible flood in a horizontal reservoir can be significantly affected by transverse mixing between solvent and oil, this displacement mechanism must be accurately simulated in the scaled model studies. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long times for experiments. If scaling requirements for miscible displacements could be relaxed while accurate simulation of essential displacement mechanisms is maintained, the utility of model studies would be greatly enhanced. The purpose of the work reported herein was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascer tain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. These studies were performed with completely miscible systems in linear, horizontal models packed with unconsolidated media. From the experimental results, a set of relaxed scaling criteria was formulated which allows the requirements of geometric similarity and equality of the ratio of viscous to gravity forces to be omitted for specified conditions. The relaxed criteria are valid whether transverse mixing is by molecular diffusion or by convective dispersion. Correlations which permit prediction of vertical sweep efficiencies in linear, horizontal reservoirs were developed from the experimental data when transverse mixing is by molecular diffusion. These same correlations may be used when transverse mixing is by convective dispersion if an empirically defined, effective, transverse dispersion coefficient is used in the description of the mixing process. The effective transverse dispersion coefficient correlation essentially duplicates the dispersion coefficient correlation for equal-viscosity, equal-density fluid systems. Experimental values for the effective transverse dispersion coefficient can be measured readily. INTRODUCTION One of the most effective methods for evaluation of miscible-displacement oil-recovery processes is that of displacements in laboratory models scaled to simulate reservoir conditions. For these laboratory studies to be meaningful, however, the essential displacement mechanisms affecting reservoir performance must be accurately simulated. Since the performance of a miscible flood in horizontal reservoirs, or in dipping reservoirs at high rates, can be significantly affected by transverse mixing of solvent and oil, this mechanism must be considered in the design of laboratory experiments. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long experiment times. This difficulty seriously limits the utility of laboratory model studies. Craig,et al,1 demonstrated that geometric similarity is not required when mixing is unimportant. Their experimental data indicate, for the cases studied, that the displacement is sufficiently characterized by scaling the ratio of viscous-to-gravitational forces. This work suggests that relaxation of the requirement of geometric similarity and, possibly, other criteria might also be permissible when mixing is important, provided suitable groups describing the mixing process are scaled. The purpose of the work reported here was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascertain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. Consequently, laboratory investigations were made of the dependence of recovery on dispersion and other variables,

By J. A. Jargon, H. K. van Poollen

Flow of slightly compressible fluids through porous media can be described by linear equations. Many mathematical solutions- are available for the boundary conditions of constant terminal pressures or constant flow rates, or a combination of both. Various techniques of formation evaluation use drastic rate changes, such as sudden shut-in. Other methods require that the well be produced at a constant rate. In practice, one is not always able m fulfill these rigid requtirements. This report shows a methor1 by which varying-rate data can be converted to a constant-rate pressure response, called the unit response function. After obtaining the unit response function, one may analyze it, using techniques described in the literature. The method uses tile principle of superposition. Necessary data is a time history of pressure and production. If pressure changes and/or rate changes are very drastic, the unit response function becomes erratic and oscillates The erratic and oscillating results are obvious, and under those circumstances, no answer can he obtained. It appears, however, that a response function without oscilla-tion will not contain any appreciable errors —- one gets either good results or no results. This report includes a mumber of examples of converting constant-rate data to constant terminal-pressure data and vice versa. In addition, a number of field-test applications are given. This method should be useful in converting mathematical solutions from one boundary condition to another. It already has proven useful in converting varying-rate data to constant-rate conditions. INTRODUCTION Pressure drawdown tests are performed on production wells to determine various reservoir characteristics, including permeability, distances to discontinuities, reservoir continuity and wellbore conditions. An ideal drawdown test is performed at a constant production rate with pressure observation during the drawdown period. A typical drawdown curve for a constant rate of production is shown in Fig. 1. In practice, a constant production rate cannot always be maintained. Fig. 2 shows a pressure drawdown curve for a varying rate. Usual methods of analysis are not applicable to tests such as this. It is, therefore, necessary to convert the varying-rate data somehow, before usual analytical techniques can be applied. This report describes a method of obtaining a response function. A response function can be defined as the relationship between pressure and time for a well producing at a constant unit rate. Such a response function can be analyzed by the usual analytical techniques. Hutchinson and Sikora' first approximated a resistance function (response function), and by applying the superposition principle, pressures were calculated using the varying rates. If no match was obtained, adjustments were made to the response function and the closer approximation was used again in an attempt to match calculated and observed pressure behavior. If a good match was obtained: the response function was then used to extrapolate the future aquifer behavior.

Jan 1, 1966

A. M. CANDY,* Pittsburgh, Pa.-I think more stress should be laid upon the question of welding with the carbon electrode, which we ordinarily call graphite arc welding. Mr. Miller's photograph indicated that the original parent metal had been decarburized to a marked degree. It would be interesting to know the carbon content of the parent metal, and whether or not Mr. Miller has made any investigations to determine if the metal is always decarburized or whether in some instances we actually have carbon injected into the weld, which has been the understanding that has been quite prevalent. There were one or two other points that Mr. Miller brought out concerning which I desire to ask one or two questions: The illustrations that he presented were obtained with what, I suppose, would be termed a real low-carbon steel welding wire, which gives in the deposited metal grains that are more or less symmetrical, whereas the Roebling electrode, which is a mild steel of higher carbon content, apparently gives a columnar structure. I do not know which-of these I structures is more desirable, but assuming that the structure produced by the really low-carbon steel wire is the more desirable, would it not be true that the very low carbon content would, probably owing to high temperatures that prevail in the arc, result in a greater amount of oxidation and probably result in either carrying into the weld more oxide or producing more oxide on the surface as the operator progresses? The short arc is an advantage in all cases. Whether Mr. Miller's trouble is oxide or nitride, the short arc helps him out, because the closer the end of the electrode is to the work the less chance there is for either oxygen or nitrogen to get in. And whichever is the cause of the trouble, the short arc keeps it out by lessening the time in which the steel is molten and the amount of air that gets in. It also makes sure that the molten metal will not fall into the crater. Everything is in favor of the short arc.

Jan 4, 1919

By Alan K. Burton

Along with tires and transmission systems, engines have been a limiting factor in the growth of large off- highway trucks. The problem, primarily, has been the development of reliable, high-performance engines that are not prohibitively heavy or expensive. For many years, horsepower to overall truck weight ratios have been in the vicinity of 300 lb per hp for rear dump units up to 50 tons capacity. This ratio is obviously very poor when compared to the much lighter and smaller highway trucks, which frequently have a performance ratio of 100 lb per hp. Unfortunately, the larger mining trucks have not been able to match even the 50-ton trucks, and in some cases, ratios have dropped as low as 450 lb per hp. This results in a performance of only 67% of that achieved by the older smaller trucks. Thus, the message is clear: what is needed is more horsepower and less weight.

Jan 10, 1975

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By Oswald J. Heinrich

THE serious objections to the Leblanc soda process may be enumerated as follows : 1st. The total loss of sulphur employed, equal to about one-third of soda produced. Various processes have been proposed to regain this sulphur, but none have come into practical operation on a large scale. 2d. The great bulk of waste products, equal to nearly twice the amount of soda, which forms a serious annoyance about the works. 3d. The complicated series of operations necessary. 4th. The large amount of labor and fuel required. 5th. The production of noxious gases which necessitate extensive condensing arrangements. 6th. The large capital necessary for the erection and maintenance of the plant. These objections have long been recognized, and many attempts have been made during the last thirty or forty years, to discover and introduce a cheaper and more direct method for the manufacture of this important staple. The reaction between bicarbonate of ammonia and common salt, whereby bicarbonate of soda, insoluble in a solution of chloride of ammonium, is precipitated, has been closely studied for the last twenty-four years, on account of its simplicity and the purity of the product it affords. This ammonia-soda process is now so far developed, that while it is not .in position to entirely replace the Leblanc process, yet it can successfully compete with it where the conditions and localities are favorable. The advantages of the ammonia-soda process may be summed up as follows : 1st. It is independent of the essential agent in the Leblanc process, viz., sulphuric acid, and hence can be established in those localities where salt is abundant, and yet where sulphuric acid could not be made, or where it could not be transported profitably. 2d. The ammonia-soda process being a " wet" process, the evaporation of salt brines to obtain the solid salt required in the Leblanc process, is rendered unnecessary. 3d. The direct conversion of chloride of sodium into bicarbonate of soda, which can readily be converted into the maketable monocar-

Jan 1, 1879

By C. C. Wright, R. J. Day

ALTHOUGH data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buck- wheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths-a few inches long-as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced. This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organizations-individually, together, and in co- operation with other interested groups- have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop

Jan 1, 1948

By N. Nakanishi, C. M. Wayman

The effect of small copper additions on the mar-tensitic transformation behavior in Au-47.5 at. pct Cd was studied by measuring electrical resistivity as a function of temperature. The transformation behavior was found to change and transformation start (M,) temperatures for both the ß to ß' and ß to ß' transformations were depressed substantially by the addition of small amounts of copper. Both M, temperatures were lowered approximately 70°C per at. pct Cu. Copper also had the effect of narrowing the transformation hysteresis region (resistivity us temperature), and for the alloy Au-47.5 Cd-1.5 Cu there was little or no hysteresis; in this alloy, the reverse transfmmation upon heating apparently occurs below the thermodynamic equilibrium temperature, To. THE ß phase in the Au-Cd system occurs at the electron/atom ratio 3/2, and is similar to other ß phases in alloys based on copper, silver, or gold. It is of the CsCl type, in which a considerable degree of long-range order persists to the melting temperature.' The phase boundaries of the ß phase are not known precisely below 300° C, but at room tem- perature the phase exists from approximately 46 to 52* at. pct Cd.2 At low temperatures, the ß phase transforms in a diffusionless (martensitic) manner. Alloys having a composition near 47.5 pct Cd transform upon slow cooling to an orthorhombic3 phase, ß', at - 60°C. Alloys having a composition near 49.0 pct Cd, transform at - 30°C into a phase, ß", which has been recently identified as trigonal.4 Alloys having compositions near 48.5 pct Cd will transform into both the 0' and 0" phases over a range of temperatures. The progress of transformations can be observed

Jan 1, 1963

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor's analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

By D. Harrington

One of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo.; their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies were made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to coöperate. While the coöperation of the mining companies is necessary, the companies are put to practically no expense other than supplying a guide to accompany the investigators underground, the length of time spent

Jan 1, 1922

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By George A. Macready

Trinidad, British West Indies, is an island near the north coast of South America, situated between latitudes 10" and 11" N., and opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,-250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi. (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 31/2 mi. south of Pitch Lake on Lot Three of Morne 1'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 1, 1921

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By H. W. Camp

Although the situation in the oil industry during the past year has not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new product,s and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the antiknock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gasoline is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and competitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called '(reforming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932