Search Documents

By F. A. Harvey

DURING the last few years, there has been a constant tendency toward increasingly high temperatures in many lines of industry. The necessity for increased production of coke gave a 16-hr. coking period where we used to have 24 or even 30-hr. periods. Mechanical stokers have increased the temperatures in boiler furnaces. The use of a chain-grate stoker with coke-breeze fuel necessitates a low arch in the furnace and temperatures run much higher than firebrick were formerly called upon to stand. These higher temperatures have necessitated more rigid tests and the separation of even high-grade firebrick into separate classes. More severe tests mean higher temperatures and closer control, and this, in turn, means better pyrometer tubes. Platinum couples do not have a very long life when used at temperatures exceeding, say, 1200° C., but the proper selection of a high-grade brick to be used in a-boiler setting will save the cost of several couples; and with freight rates continually increasing it becomes increasingly important to know where brick may be bought, nearest the job, that will prove satisfactory. Couples that will stand continuous use at higher temperatures, of tungsten, molybdenum, or other metal, will doubtless be forthcoming as soon as the need becomes sufficiently urgent. There are on the market several tubes that are entirely satisfactory for temperatures up to 1300° C., if properly protected from heat shock. The Semet-Solvay Co. makes a practice, however, of testing silica and clay firebricks at 1450° C. for 72 hr., and so far we have been unable to find a tube that- is entirely satisfactory for this purpose. A graphic record of the temperature during the entire test is extremely desirable and hence we have been trying out anything that gave promise of success. Several years ago we were using insulating tubes, made purely for electrical work, of vitrified porcelain. These tubes stood up under any temperature we were able to reach and were apparently impervious to gases. When this stock gave out, due to mechanical breakage, we tried other insulation tubes only to have them melt down like glass. Marquardt Masse tubes were tried next under a statement from the distributors

Jan 9, 1919

By F. B. Foley

With the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal1 published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-of theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1/14-in (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. with time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the great decrease in breakage by the use of smaller diameter drills. The figures are given as so many drills sharpened, but there is no way of determining the percentage of

Jan 1, 1922

By Francis Foley

WITH the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges' the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal' published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-f theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1 ¼ -in. (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. With time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the "enormous decrease in breakage by the use of smaller diameter drills." The figures are given as so many "drills sharpened," but there is no way of determining the percentage of

Jan 6, 1921

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By J. A. Marton, N. Brown, M. Herman

AT high temperatures a deformed polycrystalline metal shows grain-boundary displacement in preference to slip lines.' This has led to the conclusion that overall strain at high temperatures is produced chiefly by grain-boundary displacement. Detailed microscopic examinations of individual grain boundaries have shown many interesting ways by which their displacement occurs; sometimes no grain deformation was observed except possibly in the immediate neighborhood of the boundary. However, X-ray examinations show that at high temperatures subgrain formation occurs;Y he process, generally called polygonization, results from lattice bending and the subsequent climb of dislocations to form low-angle boundaries. Quantitative measures of the grain-boundary displacements show that they make a minor geometrical contribution to the overall strain; the major contribution is made by grain deformation."'" A relationship between grain-boundary displacement and grain deformation was suggested by McLean, who showed how the degree of polygonization would determine the amount of grain boundary displacement: and by Dorn, who showed that for a given creep stress, the amount of grain-boundary shear was related to the overall strain and was independent of temperature.' Although the grain-boundary displacement may make a small geometrical contribution to overall strain, it may still be the rate-controlling factor in high-temperature creep. If in general grain-boundary displacement and grain deformation are dependent quantities, then the designer of a creep-resistant metal would like to know whether it is more desirable to strengthen the matrix of the grain or to increase the strength of its boundary. The widespread interest in the relationship between temperature and grain-boundary displacement makes it desirable to test the generality of Dorn's result6 that the ratio of grain-boundary displacement to overall strain is independent of the temperature for a given creep stress. In this investigation p-brass was used because it produces sharp grain-boundary displacements above 400°C. Since B-brass undergoes an order-disorder transformation which abruptly strengthens the grain, it is an excellent metal for determining whether grain-boundary displacement or grain deformation is the rate-controlling factor in creep. The problem will be confined to the temperature range where

Jan 1, 1958

By W. L. Saunders

IMPORTANCE OF ROCK DRILLING. IT has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended. annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. 'The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become ,so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 9, 1913

By R.J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By R. J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By DeVerle P. Harris

Risk for most mineral investments is greater than that of average business ventures, because the physical and economic characteristics of the mineral deposit are never known with certainty. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with the adoption of the project, methods of risk analysis are important in project evaluation and investment selection. The conceptual framework for risk analysis and the means by which some of the recommended practices might be implemented are examined. In addition to the normal business risk due to market forces, the physical and economic characteristics of the mineral deposit are never known with certainty, for only partial or indirect information is available, such as data from drill cores or surface and underground workings. Consequently, risk for most mineral investments is greater than that of average business ventures. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with adoption of the project, methods of risk analysis are important in project evaluation and investment selection. This paper examines the conceptual framework for risk analysis and means by which might be implemented some of the recommended procedures. Utility Theory A discourse on risk and its impact upon investment selection quite often leads the reader into the concept of utility theory, for utility theory is a device constructed by economists to measure the satisfaction an individuai receives from a good; in the case of investment analysis, that good is the outcome of an investment. It briefly is reviewed here to describe the reaction of the individual to risk and as a stepping stone to other techniques more suited to risk analysis at the level of the firm. Utility theory proposes that an investor possess a utility map (curve), such as indicated in Fig. 1, which indicates the value in utiles of potential monetary rewards to an individual with some specific endowment of resources. Points on this map are obtained from the following relationship:

Jan 1, 1971

By H. A. Schwartz, W. Kenneth Bock

IN this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the position of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 400°C. (750°F.).

Jan 1, 1944

By W. J. Schuster

Safety in coal mines depends largely upon adequate training of the foreman. Although management must provide modern and safe equipment and at all times keep mines in first class condition from a safety viewpoint, final results will be determined by the quality of supervision. HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large underground mines in eastern Ohio. The section of Pittsburgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it. Haulage System The Pittsburgh No. 8 seam in eastern Ohio is relatively level, with only minor local dips. Throughout the Hanna Coal Co. mines, entries are generally 12 ft wide. Rooms are driven on a 60" angle on 30-ft centers and are 22 ft wide. No attempt is made to extract the 8-ft pillars between. The entire length of main line haulage is gunited in one mine, and a major portion in another. Two of the mines have single-track main haulage roads with passways. The third, a new mine, is double-tracked, and the roof is supported by steel crossbars, 60 lb or heavier, spaced on 4-ft centers and lagged. In recent years timbering on main line and secondary haulage roads has been accomplished by one of two methods: 1—crossbars are supported on a small section of post set in a hitch hole in the rib, or 2—or a hole is drilled in the rib about 12 in. below the roof, of sufficient depth to fasten securely a short length of 40-lb rail, the bottom of the rail facing the roof, on which a short post is set directly under the crossbar. At present the hitch-hole timbering method is favored. At two of the mines the main line haulage locomotives are 26-ton, 8-wheel units. These locomotives are of the axleless type, each wheel being individually mounted on the frame. The motorman's compartment is encircled by 3-in. armor plate for the protection of the occupants. At the third underground mine conventional 15-ton locomotives are being used. However, these locomotives have been completely rebuilt in the company's shops. Equipment has been streamlined and quarters have been provided for two people, who are protected by heavy steel plate in much the same way described above. This modernization program has been completed on all secondary haulage locomotives at the three mines, and the company is well on the way to similar equipment of the 6-ton section locomotives. The following additional features have been included in their modernization: 1—additional support for the motors to prevent their falling to the middle of the track and derailing the locomotives should a break occur in the suspension bar support; 2—installation of additional bracing to prevent brake rigging from becoming displaced and causing derailments; 3—enclosure of all electric wiring in conduit or raceway; 4—provision of an enclosed compartment for the storage of re-railers, jacks, and other equipment, so that they need not be carried on the outside of the motor; and 5—redesign of the end of the locomotive opposite the operator's compartment to prevent anyone's mounting from that direction. It is interesting to note that some

Jan 1, 1955

By William P. Blake

We are so familiar with water in its liquid and its solid form, that we seldom think of it as a mineral, and still less as a mineral product of any considerable industrial importance, though in the form of ice it is mined and stored up in enormous quantities yearly. The industry is peculiarly American, and in no other country has the business of cutting and storing ice been so well systematized and perfected. The interest has grown steadily from year to year, until it has attained large proportions, the annual production being counted in millions of tons, requiring, in the aggregate, a large investment of capital in all the Northern States. It gives employment, also, to thousands of men and horses, in the depth of winter, when farming work cannot be carried on. Ice is not only a luxury, but a necessity, in our climate, and is indispensable in many manufacturing operations: and finds constantly increasing applications and uses. As the industry has grown, so the necessity for suitable implements and tools has grown with it, and it has become necessary to systematize and cheapen the methods of handling such a large amount of material with rapidity and economy. As the industry is properly a branch of mining, and as our mining literature does not, to my knowledge, contain any description of the methods and appliances used in it, it seems desirable to place a brief description on record in our Transactions, and I therefore offer to the Institute the following outline description, based partly upon observations for several years past of the methods and processes employed, and partly upon the information obtained from prominent ice-miners and from the manufacturers of ice-tools. My acknowledgments are particularly due to the firm of W. T. Wood & Co., of Arlington, Massachusetts, for much information in detail, and also to the Knickerbocker Ice Company, of Philadelphia. The wood-cut blocks used in the illustration of this paper, have been kindly lent by both of these firms. The sequence of operations in getting ice is as follows : 1. Wetting down a light snow. 2. Scraping off an excess of snow, if present. 3. Marking out the field. 4. Ploughing and cross-ploughing. 5. Cutting the channel and detaching large floes.

Jan 1, 1883

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paper. The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal.

Jan 1, 1960

By R. E. J. Putman

Introduction Self-tuning regulators are a class of controllers built around the concepts of sampled data theory, and are especially suitable for implementation in a digital microprocessor or minicomputer control system. The algorithms used are distinctly different from those based upon analog control techniques and include automatic adjustment features which permit them to adapt to unmeasured changes (in, for example, ore grindability) or process nonlinearities (as exhibited by cyclone classifiers). They are also designed to handle transport lags in a simple manner, for example, anticipating the effects of a variable recycle rate on particle size distribution. The advent of distributed control systems will encourage the exploration of these techniques in the minerals processing industries, and particularly for improving the control of comminution circuits, which are especially energy intensive. This paper outlines some current work in progress on this topic. Background Those engaged in the practice of process control have long had two philosophical problems for which solutions have been actively sought - what is optimal control and how can we attain it in some heuristic fashion automatically. The basic analog controller can be represented by the differential equation: [V = Ko + K1 f y • dt + K2 dt(1)] where: v and y are the instantaneous values of output and error respectively and K0, K1, and K2 are tuning constants. The empirical rules for establishing the values of K0, K1, and K2, which provide stability, have evolved from the initial suggestions of Ziegler and Nichols(9) in 1942 and have served their purpose well. However, later analyses demonstrated that there are in fact many combinations of the values of K0, K1, and K2 which, besides being stable, behave better or worse in relation to other process control criteria; some examples are duration of error, amplitude of a damped response, magnitude or rate of movement of control valve or adjustment of speed regulator, etc. The definition of optimality had broadened. In 1964, Kalman(4) published his classic paper which tried to resolve these problems. He defined a

Jan 1, 1982

Tars Committee is the result of a desire of the authorities in charge of the publications of the four national engineering societies to co-operate in this matter. The members of the Committee are the following: Charles WarreN Hunt, Secretary of the American Society of Civil Engineers. D. S. Jacobus, Vice-President of the American Society of Mechanical Engineers. Joseph Struthers, Assistant Editor of the American Institute of Mining Engineers. CaRy T. Hutchinson, Chairman of The Editing Committee of the American Institute of Electrical Engineers. This Committee has held several meetings; it seemed advisable, at the outset, to limit its discussions closely to the general subject of abbreviations. Further, it seemed best to formulate a few general rules to be followed in making abbreviations, rather than to compile a list of forms to be recommended. The Committee decided to limit the subject more narrowly by considering only abbreviations to be used in the text, or general reading-matter, arid not those to be used in special matter,

Jan 1, 1905

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

By W. L. Saunders

It has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 1, 1914

Hermann A. Keller was born in Philadelphia, Pa., Mar. 23; 1860. He received a preliminary education at the gymnasium of Darmstadt, in Germany, and subsequently entered the University of Pennsylvania, graduating in 1881. After serving for a few months as an assistant instructor in mining and metallurgy at the University, he went to Leadville, Colo., where he became, at first, assayer and chemist, and in due time (1886) superintendent of the Arkansas Valley smelting works. In 1888, he was appointed metallurgist of the Globe works at Denver; in 1889, superintendent of the Philadelphia works at Pueblo; and in 1891, superintendent of the Parrot works at Butte, Mont., where he remained until 1896, in which year he was employed to reconstruct the smelting plant of the Mountain mines at Keswick, Cal. In 1897, he opened an office as consulting engineer in San Francisco; and from this time on enjoyed a wide practice both as metallurgical and as mining engineer. In the former capacity, Mr. Keller had already distinguished himself by the invention of the Keller mechanical roasting furnace employed at the Parrot works in Butte and the Germania works near Salt Lake. He was a frequent contributor to the technical journals, and he collaborated in the preparation of the chapter oil "Bessemerizing" in Dr. Peters's work, "Modern American Copper-Smelting." It is a curious coincidence that these two friends and collaborators died at almost the same time, Keller in Arizona and Peters in Massachusetts on the 16th and 17th of February respectively. The latter years of Mr. Keller's life were largely given to the examination and development of mines in all parts of the world-Alaska, Chile, Germany, etc. He finally established his professional headquarters in New York City. His death was caused by an underground locomotive accident at Clifton, Arizona, on Feb. 16, 1917.

Jan 5, 1917

By W. R. Crane

MINING of the red iron ores of the Birmingham district has been carried on energetically during the past 50, years, and their development has created a large iron and steel manufacturing, center, the only important one in the South. The district produces approximately 10 per cent. of all the iron ore of the United States (80 per cent. of the Alabama ore mined is red ore) ; also, 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham. The rapid growth of the district has been made possible through investigations that resulted in radical changes in furnace practice, and a still greater impetus will come from the study of the low-grade, high-silica ores, as a result of which they will be made amenable to treatment by concentration. Mining practice in this district has been comparatively simple because of the occurrence of the ore; but with the-rapid extension of the work-ings and the disturbed condition of the ore bed at some distance from the outcrop, more difficult conditions are encountered and the tendency is toward worse rather than better conditions. Should the high-silica ores of the lower bench of the Big Seam become available through beneficiation, mining practice will have to be modified to meet the new conditions, which will be rendered more difficult by the increased weight of cover that will exist at considerable distances from the outcrop. Support of workings will require greater attention and the efficient and economical operation of the mines will depend largely on the successful solution of the problems of working-and handling the ore.

Jan 9, 1924

By Michael S. Koleda

Less than two years ago, the, Congress, with broad bipartisan support, passed the Energy Security Act of 1980. A decade marked by ten- fold increases in world oil prices and two major interruptions in oil flows from the Middle East had ended. An all-out national commitment to transform America's vast tar sands, oil shale and coal resources into conventional fuels had begun. The national synfuels effort was to be public-private cooperation at a scale unmatched in peace time. Private industry would own and operate the synthetic fuels facilities. Government would reduce market uncertainties to acceptable levels. The potential government commitment was substantial. Up to $88 billion would be available through the Synthetic Fuels Corporation, principally in the form of contingent financing. Billions more would be spent through Department of Energy programs. Additional incentives for alternate energy development were contained in the Energy Tax Act of 1978. The Energy Security Act clearly specified national synthetic fuels production objectives: 500,000 barrels per day by 1987 -- 2 million barrels per day by 1992. Finally, said Congress, Uncle Sam was going to do something about rapidly rising oil prices, uncertainties of energy supply, and the resulting disruption to the U. S. economy. Simply put, the purpose of the Energy Security Act of 1980 was to provide government guarantees sufficient to get synthetic fuels projects off the private sector drawing boards and into commercial production. Because of their huge cost, technological uncertainty, and lengthy pay-out period, these projects were always second place to projects of smaller size, known technology and more rapid pay-out. The Energy Security Act was the legal expression of public policy to bring the free-market synfuels timetable into line with the faster paced political timetable in the interest of national energy security.

Jan 1, 1982