Search Documents

Jan 1, 1907

Jan 1, 1908

Jan 1, 1911

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By H. A. Wilmeth

IN 1955, before planning an accelerated stripping program, Chino Mines Div. began an engineering study to improve data for estimating truck haulage costs for any future haulage layout. The study aimed to develop: 1) significant unit costs, 2) a method of estimating travel time from which truck needs and future stripping rate could be determined, and 3) yardsticks of performance to measure haulage efficiencies. It was suggested that to provide significant unit costs, expense accounts should offer management two types of cost control information-unit cost yardsticks with which monthly unit costs could be compared and unit costs for estimating future expenses for any haulage layout.

Jan 5, 1958

By Glenn C. Waterman, Scott Hazen

3.1-1. Purpose. Development drilling is directed towards determining the grade, volume, and three-dimensional outline of a mineralized zone previously located by exploration. It is distinguished from exploration or reconnaissance drilling, which has as an objective the discovery of new mineralized areas. A development drilling and bulk sampling program should furnish the following information: 1. Geology of the mineralized zone. 2. Quantitative data on grade and tons of material within pertinent cutoff limits. 3. Physical size and shape of the deposit. Areas underlain by waste as well as ore. 4. Mineralogica1 and metallurgical characteristics of the ore. 5. I1hysical characteristics of the ore. 6. Hulk samples for metallurgical testing and grade check. 7. Data on other factors that could affect mining operations, such as ground water, ground conditions, etc. 3.1-2. Procedures. There are numerous methods and techniques that are used to acquire pertinent data on a potential ore deposit. The total cost and accuracy of a development program depends on significant evaluation of the geology, proper selection of a drilling method, thorough analysis of sample data, and accurate evaluation of all the information. Knowledge of the geology of the mineral deposit is important in planning the development testing program and in evaluating the data obtained from such a program. Exploration work usually provides some significant information on the general size, shape, thickness, grade, and geology of the deposit. In some cases no further data are needed; in many cases geological complexities suggested by the preliminary work require further geological study. Of considerable importance may be the following:

Jan 1, 1968

By Harlan A. Walker

ROCK-DRILL steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. EXPERIMENTAL WORK During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from 1/8 in. to 1/16 in. [ ] In drifts and crosscut headings mounted machines were set up and holes were drilled with 1/8-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By W. A. West

ONE who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult&apos;s law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener&apos;s paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion of the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1946

By Harrison R. Cooper

Computer process analysis and control techniques are overcoming major hurdles to acceptance in the mineral industry. With the growing list of new advances characteristic of a rapidly maturing discipline, management of the companies on the leading edge are keenly aware of the advantages of using computer methods in process applications. Significant advancement is already evident in such technical areas as operations research, mathematical modeling, statistical methods, and computer-based procedural techniques. The early advances during the past decade are already documented in prior symposium proceedings of this series. Thus, the currently active areas of the advancing technology are emphasized here. This section deals with applications in pyrometallurgical and kiln processes. The two sections which follow deal with concentrating operations from two points of view: 1) mathematical modeling, and 2) on-line control. In the metallurgical field, emphasis on developing effective process computer applications for the steel industry began in the late 1950&apos;s. Simulation techniques also received substantial attention. The steel industry was soon joined by the cement industry in the development of computer methods for process applications. Computers were in use for feed-material blending and kiln control in the early 1960&apos;s. Computer development in other pyro processes, such as aluminum reduction and glass-making, also marked significant advances by the mid 1960&apos;s. Aluminum smelter potline control is a nearly universal application at this point, and the development of glass furnace computer process control represented a recent important technical advance in digital control techniques. Steel Hot strip rolling was the earliest significant process computer application in the metallurgical industry. Computer control of rolling mill operations is now a steel mill standard component, particularly in plants newly placed into production. 1, 2 Initial computer installations principally carried out procedural routines in setting mill clearances for production lot control. Recent developments are leading toward feedback control based on mathematical model techniques. 3

Jan 1, 1969

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By Maurice Cook

NORMALLY the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 min., for example, would, for many purposes, he regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals and alloys that take place on annealing, and a number of generalizations have been reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results, however, that are not covered by these generalizations can be obtained, which, in some instances, may even appear to he contradictory to them. According to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which, according to ordinary standards, would be classified as coarse or large.

Jan 1, 1938

By James Harding

THE usual method of sampling mineral deposits is to drill holes and assay the sludge or core. Though the results thus obtained may not represent the true average value of the deposit, it is on these results that estimates of practically all large orebodies are made. In a large number of cases, the results of exploitation fall far short of the estimated value of the orebody. The standard method of making these estimates is to find the cubic contents of triangular prisms, in the apexes of which the drill holes are placed, .by multiplying the surface area by the average depth of the ore in the three drill holes and then multiplying the cubic contents by the specific gravity of the ore or rock to find the tonnage. The assay value is found by dividing the sum of the products of the depth of ore in each hole and the corresponding assay value by the sum of the depths of the ore in the three holes. As the latter part of this method is subject to many mathematical errors, it should not be depended on.. Some engineers, therefore, use a discount factor, but as this factor is either arbitrarily selected or is obtained by obscure methods, the results are no better than guesswork. The standard method is correct when the drill holes are so laid out that the triangular prisms are equilateral in cross-section. But as ore deposits cannot always be drilled into at regular intervals and because of the human factor, if many holes are drilled, triangular prisms of all degrees of angularity are produced. In such cases, it is necessary to assume that the influence of the different holes is not the same in all directions, which assumption of course is absurd.

Jan 1, 1921

By Claus Goetzel

THE object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion AVERAGE COEFFICIENT PER DE G. C. OVEN RANGE 20° To 200° C. Pure aluminum &apos;31.6 X 10-6 Cast low-expansion Si-Cu-Ni-Al piston alloy 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.10-1.0 Mn) 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si) 12.8 X 10-6 Pure silver 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render it use feasible in Germany as an emergency in is- tire. The coefficients of linear expansion of several metals and alloys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850° C. for the solidus of the silver alloy. Pure silver melts at about 961° C., so that the Fin. 1.-PISTON CONTAINING tolerable depression in the solidus is rather FERRONICKEL INSERT. small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By Earle C. Smith

The Chairman.—Mr. Earle Smith has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. Smith,* Cleveland, Ohio—I will start this Off by a story oF the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "we don&apos;t make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don&apos;t dare publish the information. So if 1 collect it and hide it you can&apos;t charge me with having done anything that really disrupted the commercial situation." So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "academic " matter as far as I am concerned. I am in a situation like that of the German who was told in 1956 about the coming war. He said: "until it is your throat that is going to be cut, you don&apos;t pay any attention to what is happening to the otherman." &apos;That is the way with the problem that we have in front of us. Recently I have been told that the &apos;Omptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were nut within the compositions that were included in the specification, and therefore he as the camptroller had no alternative. It was not meeting the specification; therefore, no payment. So I I say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative , chemists who analyze some of these products or lawyers who read specifications, I don&apos;t know which man is going to be the major factor in the future. if the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for That they expect to be umpire eel. the writers would certainly realize that some of the to to which we have calmly signed our names as being O.K. are— well, as one man said to me, they might be filled by the devil, and they certainly could be filled by the Lord, but they could not he me by mankind. I would like to inject two or three things into a segregation study which I Want you to think about, because 1 would be a little surprised if there is very much discussion of them, In the first place, we generslly make steel in the United States in the basic open hearth, and I do not think there has bee,, nearly enough consideration given to segregation German the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0,60 per cent silicon have more respect than they had previously for the segregation that is within, the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another pint to which I think We ought to sis serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregat. ing iron oxide, Normally we are segregating some form of carbon or sulphur, or something like that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1945

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo ís surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proaño hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active ín 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresníllo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under García&apos;s energetic leadership the mines were reopened, and silver production began in 1832 ín spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proaño hacienda). The company formed in 11835 (Cia. Zacatecano Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

JUDGE Samuel E. Schull, in the Court of Quarter Sessions of Monroe County, Pa., handed down a decision on July 2, declaring the Pennsylvania law for the Licensing of Professional Engineers and Land Surveyors to be in violation of the Constitution of the State of Pennsylvania and also of the 14th amendment of the Constitution of the United States. The case was that of George E. Stevenson, who was arrested in June, 1922, charged with the practice of the profession of land surveying without first obtaining a state license. Mr. Stevenson had had forty years of practical experience as an engineer and land surveyor, and as set forth in the findings "had attained unusual skill, distinction and reputation in his said profession, and, on said date and for a considerable period thereto-fore and down to the present time, was and is President of the Engineer&apos;s Society of Northern Pennsylvania." That part of the decision referring to the unconsti-tutionality of the act is quoted in full as follows: This matter now comes on to be heard on argument as to the constitutionality of the said Act of May 25, 1921, P. I. 1131. The defendant urges that the same is unconstitutional: First: Because it is in violation of Article 3, Section 3, of the Constitution of Pennsylvania, which provides: "No bill, except general appropriations bills, shall be passed containing more than one subject which shall be clearly expressed in its title." Second: That the same is discriminatory and, therefore, in violation of the 14th Amendment of the Federal Constitution. In this case, we: are confronted by the Act of Assembly bearing the title "an act to regulate the practice of profession of Engi-neering and Land Surveying; creating a State Board for Regis-tration of Professional Engineers and Land Surveyors; defining its powers and duties, imposing certain duties upon the Common-wealth and Political subdivisions thereof, in connection with public work and providing penalties." We meet in the title of this act, a recognition of the fact that it is the legislative intent to deal with two professions: First: Engineering. Second: Land Surveying.

Jan 8, 1923

By D. M. Urich

New plant construction for pyrolysis and agglomeration during 1969 has been relatively quiet in the North American scene. U.S. pellet capacity approximates 52 million long tons and that of Canada 25.3 million tons. The foreign scene, however, has been extremely active during 1969, and this is expected to continue for the next several years. Changes in sinter practice have not been reported, other than a few changes towards increased bed depths and the increased use of screening facilities to size the product more closely. Interest in the field of briquetting in fields other than iron ore is high with a new fluorspar briquetting plant under construction at Brownsville, Texas. Considerable research appears to be pointed towards solving the problem of reclaiming steelmill waste products (flue dust, BOF dust, mill scale) by means other than sintering.

Jan 1, 1970