Search Documents

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe's valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasioil I have shown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By O. J. Huber

HYDROGEN effects in titanium alloys have been the subject of extensive research in recent years. Lenning, Craighead, and Jaffee1 showed that hydrogen embrittles a titanium and, at the same time, elevates the temperature at which the transition from brittle to ductile failure occurs during impact testing. In later work: the same investigators concluded that several all-ß alloys tolerate large amounts of hydrogen without serious damage to mechanical properties, but two-phase alloys suffer varying degrees of embrittlement, depending upon the specific ß-stabilizing addition used and whether or not an a stabilizer is also present. The mechanism of hydrogen embrittlement has not been clearly established. Strain rate has been shown to be an important factor and, therefore, a strain-aging phenomenon is suspected to cause the effects that hydrogen has produced on mechanical properties.3-5 Ripling6 has pointed out that ductility damage varies inversely with strain rate in a-ß alloys and directly in a alloys. This effect in a alloys can be associated with transition-temperature behavior, but the embrittlemeat mechanism in two-phase alloys remains in question. During the course of research conducted for the U. S. Air Force, a dark-etching phase has been observed at the grain boundaries of certain two-phase titanium alloys after duplex (solution plus aging) heat treatments.5-7 An example of the dark-etching interface phase is shown in Fig. 1. Decrease in ductility accompanies the appearance of the minor phase but has not always been attributable solely to the presence of the phase. Although the dark-etching phase has been observed in alloys under a rather narrow range of heat-treatment conditions, it is of general interest since it is always associated with the presence of hydrogen. The known embrittling effect of hydrogen makes any facet of its behavior of particular importance. The intergranular phase has been observed in titanium-base alloys with relatively high amounts of the ß-stabilizing elements. Specific examples of such alloys include Ti-5 pct Mn-2.5 pct Cr, Ti-3.5 pct Cr-3.5 pct V, Ti-8 pct Mn, and Ti-3 pct Mn-1

Jan 1, 1958

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By R. J. Mechin

Top-slicing was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent of the Santa Gertmdis mine. There then existed 1200 ft. below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 354.2 ft.) a block of ore having a length of 295 ft. and an average width of 82 ft. and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing. Description of Block of Ore Former operators, when mining the original vein, left in the foot wall ore of too low grade to be profitable at the time; also, considerabe low-grade material was sorted out and stored as filling in the stopes. Some pillars were left in place, either for support or because they were not payable. All this has formed a body of ore that can now be exploited

Jan 1, 1925

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By J. C. Todd

The volume of air needed to move the combustion wave through each acre-foot of the reservoir is a very important quantity for engineering economic analyses. A new method, which involves backflowing the injection well, has been developed for determining the air requirement .for the forward combustion thermal pilot in the Delaware-Childers field. The method depends on measurement of the total volume of air injected and measurement of the pore volume in the zone swept out by the combustion front. The basic premise of the method is that the pore volume of the swept zone contains air, while the formation around this zone contains flue gas, oil and water. The pore volume of the swept zone is determined by blowing down the pilot section of the formation through the injection well after the pilot is shut down. Oxygen balance is used to differentiate between air from the swept zone and flue gas from the surrounding formation. Data indicate that air'is produced from the swept zone by relatively efficient miscible displacement by the flue gas. The pore volume occupied by the air in the swept zone is determined by simple PVT relationships. The average temperature of the swept zone is calculated by heat balance from the total amount of heat generated during the pilot and losses to the surrounding formation. The new method was applied successfully at the conclusion of the pilot in the Delaware-Childers field; the air required for the reservoir conditions involved was calculated to be 19.2 MMscf/acre-ft of reservoir swept. INTRODUCTION One of the most important pieces of information to be found from a forward combustion pilot is the air requirement; that is, the volume of air needed to move the combustion wave through each acre-foot of the reservoir. Compression costs per barrel of oil recovered, which are a direct function of the air requirement, are a large portion of the expenses incurred in the thermal recovery process. Thus, the profitability of thermal recovery depends largely on the air requirement, which is a measure of the amount of fuel deposited and burned in the thermal recovery process. Several attempts have been made to correlate crude oil properties with fuel deposition and, hence, air requirement.l*2 Other attempts have been made by our laboratory to find the air requirement by material balance, gravity survey, pressure transient analysis,3 magnetic survey and the poten-tiometric model. Better methods are needed to predict more accurately the economics of fieldwide application of the process. Another method of finding the air requirement consists of operating a pilot thermal project for several years. This is followed by an extensive coring program to define the volume swept by the combustion wave. The air requirement is found from the total injected air divided by the volume of the swept region found from the coring operation. This method is costly; an adequate coring program usually costs several hundred thousand dollars. A thermal pilot was operated in a watered-out portion of the Delaware-Childers field, Bartlesville sand, from Nov., 1960, until May 3, 1965. One of the primary purposes of this pilot operation was to determine the air requirement for economic calculations which determine the advisability of expanding the project to the entire 128,000 acre-ft field. Barnes4 has described the result of this pilot operation,, including calculation of the air requirement from limited coring data. The value obtained, as calculated, was 15.8 MMscf/acre-ft. One purpose of this report is to describe a new method of finding the air requirement from a thermal pilot operation. A second purpose is to describe the application of this method to the Delaware-Childers thermal pilot. THEORY AND DESCRIPTION OF THE METHOD The combustion zone in the forward combustion process is propagated from injection w producing

Jan 1, 1970

By J. R. Linney

Demand for eastern magnetite in 1948 necessitated practically all eastern magnetite industries to operate on a six-day week, with the result that over 11,000,000 long tons of crude ore were mined, and the shipping products amounted to approximately 5,000,. 000 long tons. Reports indicate that operating on a six-day week and doing maintenance work on the seventh day was satisfactory and resulted in excellent continuity of operation. In the Port Henry district, Republic Steel Corp. once again set new all-time records for the production of crude ore and total shipping product; 1,868,000 long tons of crude ore were mined, 945,000 from the Old Bed mine, 408,500 from the Harmony mine, and 514,500 from the Fisher Hill mine. Of the 969,000 long tons of shipping products, 663,800 long tons were sinter, 181,000 lump ore, and 115,200 con¬centrates.

Jan 1, 1949

By M. J. Spendlove, H. W. St. Clair

The problem frequently arises, particularly in refining metals or smelting scrap metals, of separating metals in the metallie state. Many metals may be separated by taking advantage of their difference in vapor pressure. Such separations can be made at atmospheric pressure, but the separations are much more selective and can be carried out at considerably lower temperatures if the distillation is done at pressures of a few millimeters or less in an evacuated enclosure. Until recently, this has not been considered feasible as a metallurgical operation, but the recent improvemcnts that have been made in vacuum technology have broadened the applicability of vacuum processes and have prompted re-examination of low-pressurc distillation of metals as a practicable process. The distillation of zinc from lead is one separation that has already been reduced to practice.l This paper is the first of a series of studies being made on separation of nonferrous metals by distillation at low pressures. Although these experiments were confined to the separation of zinc from aluminum, the significance of the results is by no means confined to these two metals. The purpose has been to investigate a metallurgical technique rather than merely to devise a means of separating specific metals. The experimental work on distillation of zinc from zine-aluminum alloys at reduced pressure grew out of earlier work on distillation at atmospheric pressure.2 The earlier work indicated that it would not be practicable to decrease the zinc in the alloy much below 10 pct owing to the high temperature required. Therefore attention was turned to distillation ah low pressures, at which lower temperatures are required. After preliminary tests were made in a small, evacuated tube furnace, a larger furnace having a capacity of 100 to 150 Ib of metal per charge was constructed. Distillation tests were first made on pure zinc and then on aluminum-zinc alloys of various composition. Particular attention was given to the limit to which zinc could be reduced in the residual metal. Data were also taken on the rate of evaporation, and heat balances were made for both the crucible and the condenser. Distillation Furnace The vacuum-distillation unit is illustrated schematically in Fig 1. The major components are the induction furnace, the condenser, the vacuum system, and the power-conversion unit. Power is supplied to the induction furnace from a 50-kw 3000-cycle motor-driven alternator. The pressure in the furnace is reduced by a vacuum pump having a nominal pumping speed of 10 liters per sec. When in operation, the metal vapors travel upward from the furnace to the water-cooled condenser where they are collected in amounts of 50 to 100 lb. The condenser is removed with aid of an electric hoist. When the system is under vacuum, the condenser is made self-sealing by a rubber gasket between the smooth-faced, water-cooled flanges at the top of the furnace and the bottom of the condenser. The pressure of the atmosphere is more than sufficient to insure sealing. At the conclusion of an experiment, the residual metal can be removed from the furnace by removing the condenser and tilting the furnace with the electric hoist. The metal was cast into the molds carried on a mold truck. A photograph of the furnace and auxiliary equipment is shown in Fig 2. The details of the vacuum furnace are illustrated in Fig 3. The furnace proper is made vacuum-tight with rubber gaskets placed at each end of a fused quartz cylinder. A clamping plate at the bottom and a ring at the top are made to squeeze the rubber between the metal and the end of the quartz tube. A large graphite crucible placed inside the quartz cylinder is thermally insulated and physically supported by refractory insulating bricks. A thermocouple in a quartz protection tube is located at the bottom of the crucible: the leads pass through a rubber seal in the bottom plate. The supporting structure for the furnace is an angle iron frame with transite board sides. The condenser is made in the form of a water jacketed cylinder with an opening to the vacuum line at the top. The bottom has a projecting skirt inside the machined flange to provide additional cooling for the rubber gasket. Condenser sleeves are made in the form of two semicylindrical pieces of sheet metal that fit snugly inside the cooling jacket. The split sleeve facilitates removal of the condensate. Measurement of Temperatare and Pressure The metal temperature was measured by a platinum-platinilm rhodium thermocouple inserted in a well extending up into the bottom of the graphite crucible. During rapid evaporation there is a wide difference in temperature between the surface and the main body of metal in the crucible because of the large amount of heat that must be conducted to the surface to supply the heat of evaporation. The heat of

Jan 1, 1950

By J. J. Fritts, J. L. Patrick, T. L. Wright, C. O. Ensign, W. S. White, J. W. Trammell, J. C. Wright, D. J. Hathaway, R. J. Leone

The copper deposit at White Pine, Michigan, from which a little more than 5 per cent of United States primary copper currently is produced, is a large stratiform orebody, 4 to 25 feet thick and several miles across. The present ore column, containing about 1.2 per cent copper as chalcocite and native copper, is confined to the basal beds of the Nonesuch Shale. This upper Keweenawan (Upper Precambrian) formation is a distinctive gray siltstone unit, about 600 feet thick, overlying and overlain by thick red-bed sequences. All these rocks contain abundant volcanic debris, but the latest known igneous activity within 50 miles antedated the Nonesuch Shale. The rocks are unmetamorphosed and only moderately deformed, mainly by tilting and faults. Pyrite, presumably syngenetic, is the only prominent sulfide throughout most of the Nonesuch Shale. The basal beds of the formation, however, contain disseminated copper minerals instead of pyrite and constitute the cupriferous zone. On a regional scale, the top of the cupriferous zone cuts across bedding, and ranges from an inch or so above the base of the formation in some areas to more than 50 feet in others. However, within the cupriferous zone the distribution of copper shows remarkable stratigraphic control. Certain beds are copper-rich compared to the beds that lie between them and the differences persist throughout the White Pine region. Several darkgray thinly laminated beds in the lower 10 to 25 feet of the Nonesuch Shale are rich enough and sufficiently close enough together to constitute a mineable thickness where they lie within the cupriferous zone. Pyrite is the characteristic sulfide of the Nonesuch Shale as a whole. The principal sulfide mineral of the cupriferous zone at the base of the formation is chalcocite. The succession of minerals outward and upward from the center of the cupriferous zone is native copper-chalcocite-bornite-chalcopyrite- pyrite. The bornite and chalcopyrite are confined to a narrow fringe at the margin of the cupriferous zone. This pattern of mineral zones is believed to represent reaction between syngenetic pyrite and introduced copper. The main copper mineralization is independent of structure and apparently antedates deformation. Details of the geometry of the cupriferous zone indicate the possibility that copper was introduced from the underlying sandstone prior to lithification. The source of the mineralizing solutions and their copper is not known.

Jan 1, 1968

By Robert B. Coleman

The recent surge in demand for uranium in the US, accompanied by a significant increase in price, has stimulated the search for and development of lower grade ore bodies. At the mill, this translates into much larger throughputs and-compounded by many recently enacted environmental considerations-has made the cost of milling a critical factor in today's uranium production economics. The three conventional milling methods employed in the extraction of uranium ores are reviewed in the following sections.

Jan 10, 1978

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By R. F. Jones, N. E. Truitt, M. Prats

In most published discussions and theories of in situ combustion, the combustion fronts are assumed to be vertical. However, evidence from field tests leaves no doubt that combustion fronts often advance more rapidly along the top than near the bottom of a formation as a result of difference in density between injected air and formation liquids. The approximation proposed in this paper to determine the movement of the resultant tilted combustion surfaces states that the vertical rate of movement of combustion surfaces is proportional to the horizontal oxygen flux. Where self-ignition is possible, the proposed method demands that a secondary combustion surface exist around production wells which produce some oxygen. These secondary combustion surfaces may be formed long before the primary combustion surface can advance from injection to production wells. Heat liberated near production wells at these secondary combustion surfaces can contribute to an early increase in production rate. Results indicate that significant oil recoveries cannot be obtained from the usual flood patterns (five-spots, seven-spots, etc.) without producing large volumes of unused oxygen. Ideally, to increase oxygen- consumption efficiency, well patterns should allow oil production from a first line of production wells and gas production from more distant lines of producers. However, it may be desirable to produce some gas at all wells to support (and benefit from) active secondary combustion surfaces. Results indicate that the well spacing through which combustion can be advanced is larger than that predicted by other methods. A large number of production wells may still be desirable to take quick advantage of gravity drainage. From a comparison with results at South Belridge field, California, it appears that this method adequately describes oxygen concentration and temperature histories and combustion-front shapes. However, this method does not accurately locate the most advanced point of the combustion surface. There is some field evidence to substantiate the actual presence of secondary combustion surfaces at South Belridge. Use of the proposed method appears warranted at this time when lay-over of the combustion surface can be anticipated. INTRODUCTION The assumption of vertical combustion fronts has been embodied in all previous publicationsl-6 which use the movement of combustion fronts away from injection wells to determine the temperature and fluid distributions in the reservoir. The only paper concerned with a mathematical model of the combustion process in which a nonvertical combustion front is used was written by Gottfried.11 Actually, nonvertical combustion fronts have been observed in most in situ combustion field tests for which adequate data are available.7, 8, 6 In practice, the typical vertical extent of the burned zone decreases with distance from the injection well, and this burned zone is at or near the top of the sand body. In some cases, such as at South Belridge field near Taft, Calif., the combustion surface is almost horizontal over a very large area.8 Thus, for some years an obvious and serious gap has existed between theory (vertical fronts) and practice (tilted fronts). This is indicated in Fig. 1. Tilted combustion fronts such as observed at South Belridge8 sometimes result from the natural tendency of injected gases to rise to the top of an oil sand. An initially present gas cap, even if thin, would make apparent the effect of gravity segregation from the first, particularly since formations considered for in situ combustion field operations are generally selected for their

Jan 1, 1969

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By A. Keith Brewer

RECENT advances in the fields of chemistry, biology, and metallurgy have confronted the analytical chemist with an entirely new set of problems. Development of plastics and synthetics has brought about a need, not only for adequate methods for their analysis but also for the various raw materials entering into their manufacture. The remarkable advance made in biochemical and agricultural research resulting from the use of isotopes as tracers or "tagged atoms" has established the necessity for the development of methods for the concentration of natural isotopes and for a means for their analysis. Similarly the advent of new and complex alloys calls for accurate analytical methods. Fortunately the analytical chemist has been able to meet some of these new demands by adapting to his purposes an instrument which has long been the most exclusive toy of the physicists. Solubility and the chemical properties of the atoms, which have always served as the basis for chemical analysis, do not enter into this new technique. Instead, momentum, defined as mass times velocity, is utilized as the means for the separation of atoms or mass groups.

Jan 1, 1946

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,[1] little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district.

Jan 7, 1951