Search Documents

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: 1-maintenance of metallurgical balance, 2-conservation of oxide ore, and 3-mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak-Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pet, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pet of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1952

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By Nathaniel Arbiter

INTRODUCTION Almost seventy-five years ago problems in the recovery of sulfides from then designated slime fractions were the impetus for the development of flotation. The fall-off in recovery by gravity methods below about 200-mesh, and the shift from coarser vein deposits to more disseminated ores, particularly for copper, provided the background for flotation's rapid advances. Although the ensuing years have witnessed major improvments both in flotation reagents and in flotation machines, many problems are still with us. And since, with the exception of the unique leaching of chalcocite ores at Inspiration, flotation is still the exclusive mainstay for primary recovery of all base metal sulfides, the solution of these problems as they arise is vital to the well-being of the mining industry. Before considering the problems themselves, it will be useful to review the current status of sulfide flotation in the United States. The last comprehensive survey by the Bureau of Mines in 1975 (1) showed sulfide ore tonnages treated from 1960 to 1975 as summarized in Table 1; Table 2 gives similar data for the flotation of all non-sulfide ores. Noteworthy is the leveling off in sulfide ore tonnages in 1970-1975, with a probable further decline in the past three years, and the sharp drop in the number of plants floating sulfide ores. In contrast, the tonnages of non-sulfide ores floated, as well as the number of individual plants, has continued to increase. In spite of these trends, two-thirds of the total tonnage of the ores to which flotation is applied is still represented by sulfides. Average grades of sulfide ores in 1975 were: about 0.6 percent for copper; near 5 percent for lead; and near 3 percent for zinc. Recoveries averaged in the low 80's for copper; about 95 percent for

Jan 1, 1979

By Stanley W. Sundeen

2.3-1. Introduction. The subject-"Preliminary Evaluation of Coal, Metallic and Industrial Mineral Deposits for Surface Mining'-seems at first glance to be definitive and not likely to be misinterpreted. Nevertheless, there are widely divergent opinions as to what is meant by "preliminary" and even as to what is meant by "evaluation." Some definition and qualification is necessary in order to provide a readily recognized basis for discussion. Evaluation evokes the idea of organizing extant data and judging its significance especially in the economic sense. It also may evoke the concept of the physical processes of acquiring the data that will characterize the deposit such as the geologic mapping, drilling, etc. Castle (5) considers that evaluation may embrace psychological aspects wherein human traits as, for example, over optimism might cause the evaluator to overlook obvious project weaknesses. In this chapter, evaluation is discussed primarily from the viewpoint of economically appraising a project from data available at a given point in time. The qualifying adjective "preliminary" is not easily defineable. In fact, some kind of evaluation proceeds, if not continuously, intermittently over the full span of exploration and early stages of development of a deposit. Bailly (1) comments: "Sometimes, before starting exploration in new areas or countries for a given commodity, we establish models to define what minimum combinations of re- coverable grade and tonnage are needed to give the minimum acceptable rate of return established by corporate policy. Then, before starting physical exploration in any target area we try and guesstimate optimistically what best 'geometry-grade-tonnage' can be expected. If these are acceptable in light of above minimum combinations, exploration is started as soon as funds are appropriated for the target area.''

Jan 1, 1968

Aamot, Olav Crone, Chem. Engr., Elektrokemisk Raadhusgt..23, Oslo. Norway. '29 Abadilla, Quirico A., Dir., Bureau of Mines Manila, P. I. '3S Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L.. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '2S Abel, Walter D., Div. of Corporations Los Angeles, Calif. '32 Abele, Louis T., U. S. Corps of Engrs 7211 Glen Oak Ave., Baltimore. Md. '31 Abel], Leo M., Research Met., Mount Morgan Ltd Mount Morgan, Queens.. Australia. '31 Abenius, Hakan V c/o Falu Gruva, Falun, Sweden. '37 Abernathy, G. E., Geol., Kansas State Geol. Survey Pittsburg, Kan. 3S Aborn. Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abrams, Charles Jackson 1624 17th St., Denver, Colo. '3 t. Abstein. Henry T., Engr. & Mgr., Profile-Tamarack Mines CoYellow Pine, Idaho. '27 Acker, E. O'C., Met L28 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Assoc. Prof. of Met., Purdue Univ Lafayette, Ind. '35 Ackerman, E. Dumont, Sub-Surface Geol., Temblador Camp, Standard Oil Co. of Venezuela, Caripito, Venezuela. '3S Ackerman, George F.,. Div. Foreman. The Fresnillo Co Fresnillo, Zac., Mexico. '36 Adami, A. F., V.P. & Prof. of Min. Engrg., Montana School of Mines Butte, Mont. '19 Adami, Charles J., Min. Engr 99 S. Downing St., Denver. Colo. '12 Adams, Army, Cons. Engr 714 W. Main St., Grass Valley, Calif. .'37 Adams, Clyde B.. Geol.. Socony-Vacuum Oil Co., Inc 26 Broadway, New York, N. Y. '39 Adams, Ernest C., 6th Engrs Fort MacIntosh, Laredo, Tex. '35 Adams, F. J., Gen'l Agent, Gulf Production & Pipe Line Cos Fort Worth, 'lox. '29 Adams, F. S., Supt., Power Dept., Anaconda Copper Min. CoAnaconda, Mont. '37 ADAMS. FRANK DAWSON, Hon. Mbr., 1913; Logan Prof. of Geology and Dean, Faculty of Applied Science. McGill Univ., Montreal, Que., Canada. '13 Adams, Gale L., Supervisor, Process & Dev. Lab., General Pet. Corp. of California, Higgins Bldg., Los Angeles, Calif. '18

Jan 1, 1939

By Heinrich Ries

The fusion-point of clay has usually been considered to be influenced chiefly by the quantity of fluxing impurities which the clay contained. Those clays which contain a high percentage of fluxes, such as ferric oxide, lirne, magnesia, and alkalies, fuse at a low temperature. Aside from the percentage of fluxing-impurities, the size of the grains exerts an important influence. Yet, while this fact has, no doubt, been recognized by many, practically no attempts have been made to prove it by actual experiment, although in the case of fire-clays, Prof. H. O. Hofman has rather disputed it. To illustrate the point more clearly, suppose a clay to be made up of a mixture of very refractory grains, such as kaolinite, and some fusible ones. If this clay be heated, the more easily fusible grains will melt first on the surface, and the softening under heat will gradually extend from the surface of the grain to its center. The larger, therefore, the size of the grain, the longer the time required for the heat to penetrate it. Now, if two samples of clay contain the same volume of flux, but of unequal size, the one containing the smaller-sized grains should fuse first, because the fluxing materials are more evenly and thoroughly distributed through the clay, so that they will more or less surround the refractory grains, which tend to act as a framework and hold up the clay-mass when heated. In order to demonstrate the effect of fineness of grain on the fusibility of clay, several mixtures were made up, consisting of white clay and other minerals. The white clay used was a very refractory type from Georgia, the fusion-point of which lay about cone 35 of the Seger series. The mixtures were formed into small bars 1* inches long, and set on a narrow surface, so that the ends were free to bend as soon as the mass softened. They were burned in a Seger gas-furnace.

Jan 1, 1904

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

EVERY forward-looking mining company realizes the need for employing graduate mining engineers so that there will be a supply of qualified men from which to draw for company officers, executives, and mine managers. The mining industry is competing today with numerous other fields of engineering for its supply of technical men, many of which are more attractive than mining because of better pay, living conditions, and well- regulated company training programs. The Ontario Mining Association and the mining companies of Ontario are conducting a postgraduate training plan which if adopted in the United States, might well encourage top quality men to study mining.

Jan 3, 1950

By M. C. Flemings, P. J. Ahearn

Dendvite morphology of unidirectionally solidified Sn-12 pct Bi alloy was determined with the aid of X-ray and macroetch techniques. Columnar growth direction (growth direction of primary arms) in this alloy is [110]; secondary arms grow in the [lii], [111), and [112] directions. Interstices between [112] dendrite arms fill in during early stages of solidification so that well-defined (110) planes are seen in the final structure (parallel to the heat-flozo direction). Similarly, interslices betweex the [111] secondary arrlls fill in to form (112) planes, and interstices between [1111 ] arms fill in to form (112) planes. DENDRITE morphology in alloys is conveniently studied in unidirectionally solidified castings. In this type of solidification, heat is extracted from a single chill surface of the casting while other surfaces are insulated. Solidification progresses from the chill and results in cast grains that are columnar with the long axis of the grain perpendicular to the chill. Dendrite morphology is conveniently studied by examination of etched surfaces parallel and perpendicular to the chill, as previously described.'" Experimental studies on the growth direction for tin are in general agreement. The major growth direction is [110]:-' although this is altered somewhat by supercooling. In one study, tin dendrites pulled from a supercooled melt had a growth orientation 12 deg away from the [110] direction toward the [002] direction.' This orientation could be changed back to the [110] or close to the [110] direction by changing the tempera- ture gradient in the melt. In a study using autoradio-graphic techniques, (111) directions were shown to be directions of preferred growth in addition to the [110) direction.7 PROCEDURE The samples employed in this study were cut from 12 pct Bi-88 pct Sn castings, 1.5 in. in diam and 3.5 in. tall. The casting procedure consisted of heating the charge to 390°C and then pouring the molten alloy directly into a gypsum sleeve mounted on a massive copper chill. Specimens were cut from the ingot, mounted, polished, and etched with Taffs reagent [FeC13 .6H2O, 2 g; HC1, 5 cu cm;H20, 30 cu cm; CzHaOH (95 pct), 60 cu cm].' The dendritic pattern was clearly visible after etching. Photomicrographs at about 8 and 35 times were taken on surfaces parallel and perpendicular to the chill. Laue back-reflection patterns were obtained from three different columnar grains in a singIe polished face 2 in. from the chill. The cut face was polished and positioned in the beam of a Laue camera, so that diffraction occurred from a single dendritic grain. The resulting diffraction pattern was interpreted to determine crystal log raphic orientation in relation to the heat-flow direction and in relation to microstruc-ture of the given grain. RESULTS Fig. 1 shows a horizontal and vertical section of the columnar structure, at low magnification. Light regions are rich in tin, and darker regions tin-poor; the primary phase is tin-rich a phase. The two sections shown were taken orthogonally from the same metallographic specimen. It is readily seen from Fig. 1 that the dendrites have

Jan 1, 1968

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By D. L. Creighton, S. A. Hoenig

The field-emission microscope has been adapted for the study of microcrack growth during the early stages of fracture in metal wires. Cracks as small as 6 1 in length can be detected and their growth can be followed to specimen failure. The system is quite useful in searching for microcracks since only sharp-edged surface defects will emit electrons under the experimental conditions. THE conditions leading to brittle fracture were discussed a number of years ago by Griffith1 and the term Griffith Cracks is often used for the small surface cracks which are responsible for brittle fracture. Griffith's theory has been modified by stroh2 and more recent results on metals are discussed by Allen,3 pp. 123-40. At present the phenomenon is not completely understood but there is general agreement that at least in certain materials the sequence leading to brittle fracture involves several stages. The initial microcracks are present because of cooling or working stresses, Hahn et al.,3 p. 95. When a stress is applied to the specimen the cracks grow slowly until the release of stored elastic energy is large enough to accelerate the crack and provide the necessary surface energy for crack growth. At this point the growth rate appears to increase rapidly to some new equilibrium velocity, and failure occurs. Since the microcracks are usually about the size of a single metallic grain (Ref. 3, p. 99) it is not easy to find them and it is very difficult to follow their growth under stress. This paper will report on the use of a cylindrical field-emission microscope for observation of the formation and growth of microcracks. I) THE FIELD-EMISSION MICROSCOPE The field-emission microscope (FEM) has a high magnification and resolution and is almost uniquely suited for observations of microcracks. Since the FEM is relatively new as a metallurgical instrument, a short description will be given here. Normally metals at room temperature do not emit electrons; however in the presence of a strong electric-field gradient, electrons can tunnel out through the reduced potential barrier. Since this tunneling is a function of the local field gradient and the local work function, the emitted electrons can be used to produce a highly magnified image of the surface by allowing them to strike a phosphor screen. Because the electron emission is dependent upon the local field gradient, smooth surfaces emit few electrons except at very high fields. On the other hand cracks, extrusions, or other surface defects, having sharp edges, emit strongly since the field gradient is very high in the vicinity of these defects. This indicates that the FEM should be most useful for detection of microcracks on otherwise smooth surfaces. A field-emission microscope was first used by Muller4 in 1936 for observation of metal surfaces, and recent reviews have been given by Muller5 and Gomer.6 The instrument has been used for metallurgical studies in the area of surface diffusion,= recrystallization,7 and grain growth 8 (Ref. 8 is directed specifically at metallurgists). In the work of Muller4,5 and Gomer 6 the specimen was in the form of a sharp metal point at the center of a phosphor-coated glais sphere. The impact of the emitted electrons on the phosphor produced a highly magnified image of the specimens. Such a system is not practical for applying a controlled stress to the specimen and a cylindrical geometry has been used in this investigation. This allowed the application of a controlled tensile stress to the wire specimen. Normally a cylindrical FEM geometry produces magnification only in the radial direction. This is the case because a smooth wire at the center of a cylinder produces a purely radial electrical field. However, if there is a break in the smooth surface of the inner cylinder, the field near the break becomes three-dimensional and the area of the break is highly magnified. The reason for this is clear if it is recalled that the field gradient depends on the relative radii of the inner and outer cylinders; if a crack forms, its edge radii are of atomic dimensions and a very high field gradient is formed near these crack edges. Since the electrons receive most of their acceleration near the crack edge and are always traveling perpendicular to the field lines, they tend to spread out and produce the magnified image observed in the cylindrical field-emission microscope. 11) BRITTLE-FRACTURE STUDIES A) Experimental Apparatus. The geometrical arrangement chosen was that used earlier by Gifford

Jan 1, 1965

By C. S. Smith

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhard Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Post-President; John Chipman, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretory. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman- Dennis Carney John Chipman J. C. Fulton J. H. Hollomon H. H. Kellogg, A. E. Lee, R. Moddin, J. D. sullivan, and D.' Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. lnstitute of Metals DM lion: Robert Maddin, Chairman. F. Lincoln Vogel, Jr.. Vice chairman. W. A. Backofen R. W. Boliuffi J. H. Bechtold' M. B. Bever R: S. Busk C 6. Goetzel poul Gordon C. D. Grobom, Jr., Robert F. Hehe-mann R. I. Joffee F. i. Joumot Jr. lrvin R. Kromer, A. J. Leno. Horold Morgolfn, C. J. McHargue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman. T. B. King, F. C. Laogenberg, W. O. Philbrook, and T. 0. Winkler. Publishod bimonthl by the American Institute of Mining Metollurgicol and Petroleum Engineers Inc., 29 West 39th Street, New York 16, N. Y. Telephone: PEonylvanie 6-9220. Subscription $20 par yew for non-AIME members in United States and North, South and Control Americo $25 foreign; $5 for AIME members. Single copies, $4.00, single copios foreign $5,00. The AIME is 1958 by the Amarican mode or opinion axpressed in it* publications ... Copyright by the Amarican lnstitute of Mining, MataIlurgicol, and Petrolum Engineers, Inc,. . . Reg. istered cable address AIME New Yark ... Indexed in Engineering Inderx, Industrial Arts ...Index and Chemicol Number5. Absrtracis . . . Second class postage paid at New York,Indor. N. Y., Industrialond Ann Arbor, Mich.

Jan 1, 1959

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By C. L. Baker

The district of Catoree, San Luis Potosi, ranks among the first half-dozen silver-producing camps of Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapnni, Mazapil, Palomas, Musquiz, Minas Viejas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (610 m.) in 41/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catoree from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catoree, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to crosivc forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstone?, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains: some of this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution of the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebblcs, and finer detritus. According to tradition, the higher portions of the Sierra Catoree were forested with pines and cedars but none remain within the mining district, although cedar is found farther south in the range. The vegeta-

Jan 1, 1922

By G. L. Spencer

There is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and .higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiff-ness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges. Materials Used for High-silica Retorts The materials used in the manufacture of high-silica retorts at East St. Louis are fireclay, grog and silica flour. Analyses are given in Table 1. The fireclay comes from the St. Louis district. The grog consists of clean firebrick culls, and the silica flour, a very high-grade material, is purchased in the form of a flour that has been ground through 140 mesh.

Jan 1, 1931

By H. K. Shearer

Oil production in north Louisiana in 1937 was 28,668,070 bbl., an increase of 1,896,925 bbl., or 7.1 per cent over 1936, as against an increase of 178 per cent from 1935 to 1936. Gas production of 301,148 million cu. ft. from gas wells and 17,330 million cu. ft. of casinghead gas, a total of 318,483 million, was an increase of 33,483 million cu. ft., or 11.7 per cent over 1936. Well completions numbered 716, with 411 oil wells, 175 gas wells and 130 dry holes; compared with 346, 109 and 78, respectively, in 1936. There were 58 wildcat dry holes. In addition to the wildcat producers described and tabulated with the fields, there were two small, shallow gas wells in Sabine and Tensas Parishes, which did not open fields of any present importance. At the close of 1937 there were only five wildcat tests actually drilling, with nine others shut down or temporarily abandoned. Chief interest during 1937 was in development rather than discoveries. The only real discoveries were two deep gas and distillate fields, Bear Creek and Ruston. There were also three completions of gas-distillate producers from deeper formations in old fields, of which the most important was at Cotton Valley, one discovery of oil in a previously known gas sand and five or six extensions of some importance. Geological Section The columnar section in south Arkansas (Fig. 1, p. 317) also applies in north Louisiana, with a few changes noted below. The oldest known formation in north Louisiana is a bed of rock salt. Except on salt domes, only one well at Rodessa has been drilled into this salt, but it has been penetrated by a number of wells in south Arkansas. Salt domes have been discovered near Vicksburg and Hattiesburg, Miss., and a deep well in Limestone County, Texas, has drilled into rock salt. In Louisiana the distance between the "interior salt-dome basin" and a salt dome of the "Gulf Coast salt basin" is hardly 60 miles. In short, evidence is accumulating to indicate that all of Louisiana, with the possible

Jan 1, 1938

By J. H. Nead

OBJECT THE experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. CONCLUSIONS No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability.

Jan 12, 1915

By C. J. Huffman

MAGNESIUM alloy tubing and hollow shapes are finding increasingly wider usage in practical applications today. Square and rectangular tubing and hollow shapes find [ ] greater diversification in use than standard round tubing. Typical applications are roller conveyors, ladder rungs, spools, furniture, tank car loading tubes, athletic equipment, and business machine parts. In general, the amount of tubing and hollow shapes produced represent a minor portion of the magnesium extrusion business. The magnesium alloys in which tubing and hollow shapes are being produced together with typical properties are presented in Table I. MI A alloy is a low cost alloy possessing good welding and stress corrosion characteristics together with moderate formability and corrosion resistance. It is widely used for low strength applications. AZ31 B, alloy is used for moderately stressed applications and possesses good corrosion resistance and formability with fair welding characteristics. AZ61 A alloy has slightly higher physical properties than AZ31 B alloy together with good formabil- [ ] ity and corrosion resistance but slightly poorer welding characteristics. AZ80 A, ZK60 A-F, and ZK60 A-T5 alloys are used where the maximum in physical properties is required. AZ80 A alloy possesses fair corrosion resistance but with formability and welding characteristics inferior to' the other alloys. ZK60 A-F and ZK60 A-T5 alloys, while only recently offered for com¬mercial use, are finding favor due, to the higher permissible extrusion rates. These alloys possess greater toughness than AZ80 A alloy and, while of moderate formability at room temperature, are very formable at 300° to 500°F. The major portion of tubing and hollow shape production at the present time is in AZ3I B alloy. Magnesium alloy tubing is commercially available in the as-extruded condition or, in the case of ZK60 A-T5, in the as-extruded and aged

Jan 1, 1951