Search Documents

A. W. TRACY' AND D. H. THOMPSON (presented in written form).-Messrs. Ed¬munds, Anderson and Waring are to be commended for their excellent work in so painstakingly reducing to constants, the variables believed to be associated with these types of stress corrosion. An ammonia stress-cracking apparatus similar in many respects to the one described has been assembled. Certain aspects of its construction may be of interest. Tensile loading of the specimens, which are usually Y8-in. diameter wires, is accomplished by springs acting in compression in compact, portable, tubular assemblies weighing less than 10 lb. The lower end of each assembly contains the test specimen and is passed into the test chamber for exposure to the moist ammoniacal atmosphere. There is considerable convenience in being able to load the specimens in a portable unit, which may be warmed to prevent condensation, and then thrust instantaneously into the test chamber. Spring loading obviates the use of weights, but it has the disadvantage of allowing some relaxation of the load if the specimen elongates during corrosion. The maximum loss in load found so far was 20 per cent. The air supplied to the test chamber is humidified by passing it through thermo¬statically controlled water. The air is dispersed into fine bubbles by being forced through a porous ceramic filter at the bottom of a tank containing about 10 liters of water. The temperature of the water is controlled independently of the tempera¬ture of the test chamber. Thus, with the

Jan 1, 1945

By G. T. Davis, C. C. Mattax, M. O. Denekas

The effects of crude oil cornponents on the wellabil-ities of sandstone and limestone were investigated. Fractions containing cornponents differing in molecular weight and molecular structure were obtained from crude oils by distillation, extration and chromatography. Individual fractions were then tested for their effects on rock wettability. Tests indicate that sundstone wetta-bility may he changed by a complex variety of surfactants varying both in molecular structure and molecular weight. Limestone appears to be particularly sensitive to basic, nitrogenous surfactants. INTRODUCTION Investigations in recent years have shown that petroleum reservoir rock wettability can exert a significant influence on the efficiency with which oil can be produced by water flooding. While most reservoirs are presumably water-wet, they niay range in their degree of water-wettability from near-neutral to strongly water-wet.'" Reservoir wettabilities other than strongly water-wet are likely to be induced by adsorption of surface-active components froni the crude oil on the pore walls of reservoir rock.:' Little is known, however, about the nature of the surface-active materials which are likely to be adsorbed by the reservoir rock. Due to the complexity of crude oils. attempts made in the past90 isolate these surface-active components have met with only limited success. It is probable that many different types of surface-active materials arc indigenous to crude oils and that many of these may be adsorbed to varying degrees by reservoir rock. This was cxolored in the studies discussed in this paper. The over-all objective in these studies is to ascertain whether the wettability of a given reservoir can be determined by examining the surfactant content of the reservoir crude. To this end, crude oils were examined to determine the variability of indigeneous surfactants with regard to chemical type and molecular weight. Crude oils were separated by distillation into fractions differing principally in molecular weight, by chroma-tography into fractions containing compounds differing in polarity, and by solvent extraction into nitrogenous and non-nitrogenous fractions. Individual fractions were then tested for their effects on the wettabilities of sandstone or limestone rock samples. EXPERIMENTAL PROCEDURES Fractionation of the Crude Oils Samples of Miocene, Eocene and Jurassic crudes were distilled at temperatures not exceeding 200°C. The final stages of distillation were completed in a molecular still at pressures down to three microns of mercury. Fifteen to 30 fractions were obtained from each crude oil. These cuts were sufficiently broad that separation can be considered to have been effected principally on the basis of the molecular weights of the constituents of the crude oil. A considerable portion (20 to 40 per cent) of the crudes would not distill under these conditions. The residues were recovered and tested with the other fractions. Fractions differing in polarity were separated from a crude of Pennsylvanian age and an extracted sample of Miocene oil by chromatography, using a solid adsorbent. Since surfactants are, for the most part, polar compounds, chromatography should separate many of the surfactants from the crude oil. Such a separation should provide fractions containing compounds differing in molecular structure. Nitrogeneous compounds were extracted from Miocene crude oil with a solution of sulfuric acid in meth-anol. The residual oil was further processed by chonia-tography. Each of the fractions obtained by thesc procedures was dissolved in a non-polar solvent (xylene) and diluted to its original concentration in the crude oil. No attempt was made to maintain an anaerobic atmosphere above the samples while they were being dissolved. These solutions of the fractions were then tested for their effects on the wettability of sandstone and limcstone as discussed in the next section. Measurement of the Effects of Crude Oil Fractions on Rock Wettability No entirely satisfactory method for measuring rock wettability has yet been developed. All methods used are empirical. The imbibition test was used in these studies. This test is based on the tendency of a rock to imbibe the wetting phase spontaneously. For example, if a strongly water-wet rock is first saturated with oil and then placed in water, the water will quickly invade the rock by capillarity and much of the oil will be displaced. If the rock is slightly water-wet, water irnbibition will proceed more slowly and, in many instances, considerably less oil will be displaced. A water-saturated, oil-wet rock will imbibe oil. The initial rate with which water (or oil) imbibition takes place indicates, qualitatively, the degree of water (or oil) wettability of the rock.

By ANTON GRAY

In considering the possibilities and costs of discovering minerals by exploration. mineral occurrences may be classified roughly according to the size of the target they offer to the various methods that have been used to search them out. This classification is advantageous because the methods of search which might be expected to give results in one case may be totally inapplicable in others. Mineral deposits for the most part have been found in groups, or districts, in which the individual deposits occur under the same general geological conditions and usually contain more or less the same metals. There are, also, what are apparently isolated de- posits, although if the truth were fully known many of these probably would not be isolated. These districts, such as the Belgian Congo copper fields, the California Mother Lode, and the Linares lead district of Spain, form the first division of my classification. The second division is formed of the individual deposits of these districts, for example, Kambove mine in the Congo, the Kennedy-Argonaut vein in California, and the Cruz vein at Linares. The third division consists of the separate ore bodies that make up the deposits

Jan 1, 1949

By Pradeep K. Rohatgi, Clyde M. Adams

Structures obtained on freezing of several hypo-and hypereutectic Al-Cu alloys over a range of solidification rates have been examined. Dendrite spacing, L, increases linearly with solute concentration and with the square root of the inverse freezing rate. The relationship for hypoeutectic alloys is: where rate of change of fraction solid with time, is freezing rate, C is solute concentration, (pct Cu)=1. Mass transport in inter dendritic liquid during solidification is analyzed; the experimental observations suggest maximum concentration differences and constitutional supercooling in the inter dendritic liquid increase with an increase in the solute concentration. The dendrite morphology changes with freezing rate and alloy composition. The dendrites of the a phase are parallel, uniformly spaced plates with slow freezing and rods with rapid freezing. Nonor-thogonal side branching has been observed in phases with cubic and tetragonal structures. Side branches in a dendrites are orthogonal with slow freezing and at 60 deg with rapid freezing. Formation of second-phase envelopes around the Primary phase is also discussed. DENDRITIC structure is characteristic of many types of phase transformation. The most extensively studied so far has been solidification of liquid solutions. chalmersl and coworkers have interpreted the formation of dendrites in terms of the breakdown of a planar interface. Most of the work done concerns itself with the development of an instability at the interface. Little theoretical work has been done quantitatively to relate the parameters of dendritic structure to mass transport in the liquid phase. A few empirical relations based on the experimental2'3 observations exist in the literature. Several workers2 including Brown and Adams1 have studied dendrite spacing in A1-Cu system as a function of solidification variables. In most cases, dendrite spacing has been found to increase linearly with the square root of some parameter proportional to the freezing time. The effect of solute concentration is not clear; some workers report the dendrite spacing increases with solute concentration4 whereas others report vice versa.''' ~ohatgi' has observed an increase in the spacing between ice dendrites with an increase in solute concentration in water. Tiller has also suggested that dendrite spacing should increase with solute concentration. In the present work dendrite spacing and morphology have been examined as a function of solute concentration and freezing rate. The freezing rate is defined as the fraction of liquid solidified per unit time, dfs/dß?, where f, is the fraction solid and 8 the time. The fastest freezing rate studied was 4550 times the slowest freezing rate. THEORETICAL CONSIDERATIONS It is of interest to analyze the concentration distribution in the liquid phase between growing dendrites during solidification, Fig. 1. Since this distribution is a direct consequence of the rejection of solute by the growing solid, a diffusional process, the concentration gradients increase with the freezing rate. However, when solidification rate is the only variable in a series of experiments, the interdendritic liquid regions become smaller (i.e., the dendrites become more closely spaced) with an increase in freezing rate. The main purpose of the analytical treatment of interdendritic liquid diffusion will be to reveal a tendency for dendrite spacing to decrease with increasing solidification rate in just such a way that the maximum concentration differences developed in the liquid phase are remarkably independent of freezing rate. Two rather different analyses are set forth, one pertaining to the one-dimensional diffusion which obtains in the interdendritic liquid between parallel plate-shaped dendrites, and the other to the cylindrically symmetrical diffusion around rod-shaped dendrites during early stages of solidification. The results of the two analyses are quantitatively similar, correlating dendrite spacing, maximum concentration difference, and freezing rate. First consider the simpler one-dimensional case. Two parallel plate-shaped dendrites are separated by a distance, L, between centers, Fig. 1. Solidification takes place by the thickening of these plates, with solute being rejected into the liquid. It is assumed there is no diffusion in the solid. This thickening process is slow enough and the dendrite spacing small enough that the concentration differences which develop, although interesting and important, are very small (an important assumption which is verified ex-

Jan 1, 1968

Reply to discussion of the paper of C. W. Washburne, presented at the New York meeting, February, 1914 (Trans., xlviii, 687 to 694 (1914)). C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Professor Lane makes an interesting contribution to the study. of chloride waters, in saying that calcium chloride waters occur not only in the greenstones of the Lake Superior copper mines, but also in the interbedded -felsitic conglomerates and "in far-removed sandstones, e.g., near Whitefish lake, and Ontonagon, in the Michigan iron mines, and in the Storm King granite." Surely these are not connate waters preserved from the Algonkian sea, assuming that the Algonkian sediments are marine rather than continental. Finding the same type of water in the Storm King granite points rather toward an abyssal source. The possible connection of these waters with the magma of the greenstone is immaterial, although some basic calcic magma is the most probable source. It is to be expected that the ascending water of the region would be found not only in the greenstones, but in all the rocks which it could penetrate. The ascent of water of this kind along vertical passages, and the consequent addition of a common ion: to the circulating sedimentary salt solutions, would explain the precipitation and localization of the "giant, concretionary" salt plugs of the Gulf Coast, without making the ex-excessive demand for an improbable quantity of salt in the adjacent sediments that is required by the unmodified theory of Harris. With-out such a precipitating medium most of the dissolved sodium chloride would have been lost by passing on to the surface without precipitation. The base to which the chlorine ions were attached is immaterial, providing they were sufficiently concentrated, but the presence of the chlorides of calcium and magnesium in the solutions is indicated by the associated bodies of secondary dolomite.

Jan 4, 1915

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

NAME "Utah" is derived from the name of the Indian tribe, variously spelled "Yuta," "Ute," "Youta." "Uta." "Eutaw," and finally "Utah." It means "in the tops of the mountains," or "on the heights." The state emblem is the "Beehive," typical of industry. State nickname is "Beehive State." AREA Utah is the tenth state in area. It contains 84.990 square miles, of which 2.806 miles are water. When admitted as a territory in 1850. Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.

Jan 1, 1925

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ, one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect, which penetrates into the ground and is distorted and, reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in, reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to, reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are-spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1927

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field. which furnishes us

Jan 1, 1927

By M. Gensamer

ALTHOUGH a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Wever1, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel sub-jected to plane parallel deformation1,2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straight-forward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystal-lites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of pre-ferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling proc-ess the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation

Jan 1, 1936

By J. D. Meakin

J. D. Meakin (The Franklin Institute Laboratories)— In a recent paper Garofalo12 has shown that a number of experimental creep results can be represented by the empirical relation In this expression ? is the steady creep rate, s is the applied stress, and A is a constant at a given temperature; a and n are adjustable parameters. Garofalo has shown that Expression [6] approximates to a power function at low stresses and a simple exponential function at high stresses. Among the data used by Garofalo are the results we published for creep of copper." For these results we found that the best correlation was an exponential law with different parameters in the low-and high-stress region, respectively. That is, i = A exp qs where A and q have different values above and below a critical stress a,. In Ref. 13 are listed a variety of observations which support the proposal that different mechanisms are operative at stresses above and below a,, and it is not felt appropriate to repeat those observations here. The purpose of this note is to demonstrate that, although the representation used by Garofalo does fit the experimental data very well, this fit cannot be used to conclude that only one mechanism is rate-controlling. The argument is best made graphically and is illustrated in Fig. 9. The continuous curves 2 and 3 represent pairs of simple exponential functions which intersect at i = 10-5. The curve 2 closely resembles the copper results in that a change of slope of 2:1 occurs at i = 10-5; the two functions shown are in fact: e = 10-7 exp (1.150) and ? = 10-6&apos; exp (0.576s) For purposes of comparison, curve 3 represents two exponential functions with a change of exponent of 3:1 and curve 1 has the exponent 1.150 throughout. It is quite clear that a satisfactory straight-line fit is obtained on a Garofalo plot for all three curves. The curves represent processes which have either a single stress exponent or two ex- ponents in a ratio as high as 3:l. It must, therefore, be concluded that the ability to obtain a linear dependence between log i and log (sinh cyo) cannot be taken as evidence for a single activated process. In fact, to some extent the way the experimental points quoted by Garofalo lie about a best fit straight line on the log (sinh as) plot indicates that two processes are indeed occurring. This is seen in Figs. 7(c) and 8(c) of Ref. 12 where it is particularly evident that the experimental points deviate from the straight line in a manner similar to curves 2 and 3 of Fig. 9. It is, of course, recognized that the generally used exponential form is an approximation to the hyperbolic sine function which is not valid for exponents of less than 1.2, e.g., qs < 1.2. The only curve in Ref. 12 which is affected by this restriction is Fig. 6(b) where the deviation from a In ? vs s

Jan 1, 1964

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

By Charles Austin

IN an earlier series of studies on 18-8 stainless steel at 600°, 700°, and 800°C.1 one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manu-factured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in, dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0,07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recom-mended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 750°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8 -in. dia., air cooling followed the annealing treatment. These treatments per-mitted two direct comparisons: (1) between the 1150° and 950°C. treat-ments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950° and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By Jack D. Webber

The successful use of oil well packers requires, in part: an understanding of the pressures which exist at the packer in various applications and an understanding of the characteristics of the various types of packers. It is with these pressures, the resultant forces, and the characteristics of packers. that this paper is primarily concerned. An oil well packer may be defined as a mechanical device for blocking the passage of fluids in an annular space. In the more usual case, the annular space is that between the tubing or drill pipe in a well and the casing, and packers which block such an annular space are broadly referred to as casing packers. In the other case. the annular space is that between the tubing or drill pipe and the walls of an open hole, and packers for blocking this space are generally called formation packers. While the hydraulics involved are essentially the same for casing and formation packers. a greater variety of conditions are encountered in the use of casing packers and only casing packers will be discussed. After a packer has been set and a pressure seal effected between tubing and casing, the packer is comparable to a piston in a cylinder. Pressures acting upon a piston result in forces which will move the piston unless some means is provided to prevent such movement. In the same manner, pressures acting upon a packer will move the packer unless there is present a sufficiently great restraining force. PACKER CLASSIFICATIONS Packers may be classified according to the pressure conditions under which they are capable of blocking the annular space between tubing and casing. Fig. 1 shows schematically two types of packers in common use. These packers are capable of blocking the annular space against the passage of fluids under a differential pressure of significant magnitude only when the pressure in the annular space above the packing element is greater than the pressure below. It may be seen that in Fig. l-a. slips with teeth which bite into the casing and prevent downward movement are provided. In Fig. 1-h. an anchor prevents downward movement. In each case, there i-only the tubing to prevent upward movement when differential pressures act to move the packers upwardly. Packers which hold only a significant differential pressure acting downwardly have been in use since the early days of the oil industry and will hereafter be referred to as conventional type packers. In many packer applications operating conditions will 1.crult in differential pressures across the packer which will at times act to move the packer upwardly, and at other times, act to move the packer downwardly. For these applications, designs are available which will block the annular space and resist movement in either direction. Fig. 2-a shows schematically a packer of this type which is designed to be run into a well and set, and removed when desired by merely pulling the tubing. It will be noted that two sets of slips are provided-— one set above the packing element to prevent upward movement, and another set below the packing element to prevent downward movement. This packer is built around a mandrel which is essentially a part of the tubing. and which is free to move longitudinally within certain limits through the set packer. Fig. 2-b shows schematically a permanent type packer which is capable of holding pressures from either direction. Here again, two sets of slips are provided to prevenl movement of the packer. This packer is designed to become virtuallv a part of the casing when set and it is made of drillable material so that it may be drilled out when its removal is desired. The seal nipple shown effects a pressure seal between the tubing and the packer. This seal nipple is a part of the the tubing, and the nipple and tubing may be withdrawn from the well without disturbing the packer. It should be noted that these figures are not representative of all available packers which are designed to hold pressures from both above and below. Packers which resist movement in either direction will hereafter be referred to as universal type packers. There is a third type of packer in general use and this type is designed to block the passage of fluids when the pressure below the packing element ii greater than that above. This type is provided with slips which prevent upward movement of the packer and is somewhat similar to a conventional type packer run upside-down. Packers designed to hold pressure only from below are made in a variety of designs and are usually owned and operated by service companies.

Jan 1, 1949

By Jack D. Webber

The successful use of oil well packers requires, in part: an understanding of the pressures which exist at the packer in various applications and an understanding of the characteristics of the various types of packers. It is with these pressures, the resultant forces, and the characteristics of packers. that this paper is primarily concerned. An oil well packer may be defined as a mechanical device for blocking the passage of fluids in an annular space. In the more usual case, the annular space is that between the tubing or drill pipe in a well and the casing, and packers which block such an annular space are broadly referred to as casing packers. In the other case. the annular space is that between the tubing or drill pipe and the walls of an open hole, and packers for blocking this space are generally called formation packers. While the hydraulics involved are essentially the same for casing and formation packers. a greater variety of conditions are encountered in the use of casing packers and only casing packers will be discussed. After a packer has been set and a pressure seal effected between tubing and casing, the packer is comparable to a piston in a cylinder. Pressures acting upon a piston result in forces which will move the piston unless some means is provided to prevent such movement. In the same manner, pressures acting upon a packer will move the packer unless there is present a sufficiently great restraining force. PACKER CLASSIFICATIONS Packers may be classified according to the pressure conditions under which they are capable of blocking the annular space between tubing and casing. Fig. 1 shows schematically two types of packers in common use. These packers are capable of blocking the annular space against the passage of fluids under a differential pressure of significant magnitude only when the pressure in the annular space above the packing element is greater than the pressure below. It may be seen that in Fig. l-a. slips with teeth which bite into the casing and prevent downward movement are provided. In Fig. 1-h. an anchor prevents downward movement. In each case, there i-only the tubing to prevent upward movement when differential pressures act to move the packers upwardly. Packers which hold only a significant differential pressure acting downwardly have been in use since the early days of the oil industry and will hereafter be referred to as conventional type packers. In many packer applications operating conditions will 1.crult in differential pressures across the packer which will at times act to move the packer upwardly, and at other times, act to move the packer downwardly. For these applications, designs are available which will block the annular space and resist movement in either direction. Fig. 2-a shows schematically a packer of this type which is designed to be run into a well and set, and removed when desired by merely pulling the tubing. It will be noted that two sets of slips are provided-— one set above the packing element to prevent upward movement, and another set below the packing element to prevent downward movement. This packer is built around a mandrel which is essentially a part of the tubing. and which is free to move longitudinally within certain limits through the set packer. Fig. 2-b shows schematically a permanent type packer which is capable of holding pressures from either direction. Here again, two sets of slips are provided to prevenl movement of the packer. This packer is designed to become virtuallv a part of the casing when set and it is made of drillable material so that it may be drilled out when its removal is desired. The seal nipple shown effects a pressure seal between the tubing and the packer. This seal nipple is a part of the the tubing, and the nipple and tubing may be withdrawn from the well without disturbing the packer. It should be noted that these figures are not representative of all available packers which are designed to hold pressures from both above and below. Packers which resist movement in either direction will hereafter be referred to as universal type packers. There is a third type of packer in general use and this type is designed to block the passage of fluids when the pressure below the packing element ii greater than that above. This type is provided with slips which prevent upward movement of the packer and is somewhat similar to a conventional type packer run upside-down. Packers designed to hold pressure only from below are made in a variety of designs and are usually owned and operated by service companies.

Jan 1, 1949

By A. S. C. Owili-eger

The computer-aided simulation model re¬ported here is an extension of the one developed by the author while at The Pennsylvania State University. The present model, however, includes consideration of the deformability and secondary fracturing of the porous system. The modifications enable simulation of multiphase shallow unsaturated-saturated and/or artesian ground water systems in dynamic mining environments. The model has been validated, verified, and evaluated on a number of field case studies and the results have been excellent.

Jan 1, 1984

By J. G. Morlet, A. R. Troiano, H. H. Johnson

Delayed failure in steel occurs by controlled initiation and growth of a crack. The incubation period for crack initiation was measured. Crack initiation and Propagation are controlled by interaction between hydrogen concentration and triaxial stress state. The incubation period results from stress-induced diffusion of hydrogen to the point of crack initiation. THIS paper describes the phenomenon of delayed failureland the kinetics of crack initiation and propagation in uniformly hydrogenated steel. The investigation was prompted by service failures of high-strength-steel components at applied stresses far below the conventional yield strength, after the part had successfully sustained equal or higher stresses for an extended time interval. This delayed failure phenomenon, often termed static fatigue, is associated1 with the presence of hydrogen. This is not surprising, since the voluminous literature on flaking and hydrogen embrit-tlement demonstrates that hydrogen may exert a potent embrittling influence. Flakes, or internal hairline cracks in alloy-steel forgings, are related to the presence of hydrogen retained from the steel-making process.2 On the other hand, embrit-tlement arises from hydrogen introduced during surface treatments such as acid pickling or electroplating. Laboratory delayed failures have been induced in notch specimens of 4340 steel by electrolytic charging of the specimen surface with hydrogen and subsequent static stressing.l,4,5 Static fatigue was observed over a wide range of applied stresses; however, failure did not occur below a critical applied stress, designated as the static fatigue limit. In this instance the extended time for failure resulted primarily from the macroscopic redistribution of hydrogen. A crack formed to the depth of the hydrogen enriched "case* upon loading; further crack growth naturally awaited diffusion of hydrogen into the material ahead of the crack. The crack-propagation rate was therefore controlled primarily by the macroscopic diffusion of hydrogen into the specimen interior during the test. Thus, in this instance static fatigue was associated with the movement of a gross concentration gradient. However, delayed failure in steel of uniform hydrogen concentration is of greater fundamental interest, as well as commercial significance. With a homogeneous hydrogen distribution a different mode of delayed failure might be expected. As the heterogeneous hydrogen distribution became more uniform,4,5 the initial crack-propagation rate decreased markedly and, in fact, what appeared to be an incubation period for crack initiation was observed. However, the macroscopic concentration gradient precluded an accurate evaluation of these observations. Although the existence of an incubation period, up to this time, has not been established definitely, it is not amiss to point out some implications of the concept. It is of interest in all hydrogen-induced embrittlement phenomena, such as flaking, delayed failure, and hydrogen embrittlement. Much discussion has centered around the possibility of an

Jan 1, 1959

By Max Mason

In 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert&apos;s study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which automatically and continually conveys messages from underneath. We also have available the earth&apos;s gravitational field which furnishes us

Jan 1, 1929

By William B. Plank

AGAIN the records show an unprecedented enrollment of students in the mineral technology schools of the United States and Canada. In the current year, 1938-&apos;39, 9619 students were resident in the 53 schools of the United States arid 1014 in the six schools of Canada. These data are from my fifth study of the mineral technology schools of the United States and Canada. the last previous study having been made for the year 1936-&apos;37. The undertaking as previously was made under the auspices of the Mineral Industry Education Division of the A. I. M. E. The data or, the various schools were collected in the same way as for former studies.

Jan 1, 1939