Search Documents

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By Francis S. Peabody

This paper will not be a technical paper, because, although I have been in the business of mining and selling coal for 30 odd years, I am neither a mining engineer nor a practical miner. If I digress from time to time from my thesis, I must be forgiven by the expert engineers and highly technical gentlemen for whose proceedings this article is written. Waste of the wonderful store of power that the Creator placed at our disposal appears to have been the theory and the basis of our methods of extracting this power—waste from the time the coal is mined to the time it is consumed. Let us consider the prime causes of this wastage which has been the heritage of the coal mining industry. In the early days—about 150 years after " Stone Cole" was discovered in Illinois by Joliet and Marquette, and Father Hennepin noted a "cole" mine on his map—the mode of mining prevalent among farmer landowners, on whose property coal was discovered near the surface or outcropping on the hillsides, was to enter the seam by a shallow shaft or drift into the hillside and remove the coal by wedging it down until a large room was left. The roof without support would fall and our primitive coal operator would then sink another shaft or drive another drift. In these early operations only the large lumps were taken and all small pieces and screenings were left to be covered by the fall of the roof—in fact this condition prevailed in Illinois up to about 1885. Gradually the method of mining changed from the open chamber, to a single entry with rooms turned to the right and left. Later, as the demand for coal increased and the necessity for larger mines became evident, the "room and pillar" system grew to be regular practice. The room and pillar system of mining consisted of starting away from the shaft bottom or drift mouth, with a pair of entries usually 12 to 15 ft. wide and about 30 ft. center to center, one entry being used for the air intake and the other for the return air and haulage; from each entry rooms or chambers were turned, narrow at the mouth and widening

Jan 1, 1918

By W. L. McMorris, Shiou-Chuan Sun

The Convertol process was first described in Ger- many by Muschenborn1 in 1952. In the U. S. Fraser2 reported this new process in 1953, and Brisse and McMorris-resented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals.

Jan 11, 1959

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

H. H. Kellogg (Columbia University)—The accurate measurements of the equilibrium gas ratios for the reaction: Pb(1) + H2S = PbS(c) + H2 [I] reported in this paper are a distinct contribution to the literature, and the authors are to be congratulated. I wish to comment, however, on the correlation of the data which is presented. The authors show a straight line correlation of log H2S/H2 vs 1/T, Fig. 1, and are satisfied with this for calculation of ?Fo even when extrapolated to low temperature (427 °C). Heat capacity data for the constituents of this reaction are available (at least to 900°K), however, and ACP for reaction [I] is finite and positive in the temperature range studied. Simplification of the heat capacity equations yields: ?CP= 2.71 + 1.65 x 10-3T (298°-900°K) This positive value of ?CP should result in a small but noticeable curvature of a plot of log K vs 1/T. That the experimental data fail to show such a curvature may be traced to another oversimplification of the author's treatment of their data. They assume that the activity of liquid lead is unity for all temperatures, so that

Jan 1, 1961

United Engineering Trustees, Inc C E Reistle, Jr (to Oct '55), A B Kinzel, '56, Andrew Fletcher, '57, Philip Kraft (from Oct '55 to '59) The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Engineering Societies Library Board Frank T Sisco, '58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, '55, Otto Herres, '55, J K Richardson, '56, E W Bullard, '56, Alternate

Jan 1, 1955

By F. C. Newton

RefineRs of lead by the Parkes process have always been solicitous of recovering the zinc used in the desilverization, and justly so, as the loss in zinc constitutes one of the heavy costs in this method of refining. Part of this loss is due to the absorption of zinc by lead, and in the present state of knowledge is not recoverable as metallic zinc. The remainder of the zinc, which finds its way into the precious-metal-bearing crust, is recoverable and naturally engages the operators' most exacting attention. Careful elimination of the impurities in base bullion has enabled the refiner to produce a zinc crust better adapted to retorting, which reflects favorably in the zinc recovery;- and to produce a richer crust, thereby lowering the zineking cost, as the increased efficiency of the zinc results in less of it being in circulation. It is obvious that if the ratio of concentration be increased, a lessening of the amount of crust formed will ensue, throwing less work on the retorts and diminishing the amount of retort metal sent to the cupels, thus making an actual money saving in all these operations. In the effort to obtain a rich crust, the metallurgist has increased the heat to a considerable degree, upon the assumption that at the higher temperature the zinc-dver alloy could be squeezed free from the adhering lead. A further possibility for improvement suggested itself in the freezing-point curve of Prof. H. C. Carpenter, upon zinc and silver. Study of this curve disclosed the existence of a definite chemical compound, Zn3Ag2, with a freezing point of 665" C., a promising compound for practical application. In the experiment undertaken it was endeavored to force this compound into the crust, hoping thereby to obtain a higher concentration than formerly. It was recognized that in bringing a large kettle of lead to such a heat, more fuel would be used, the life of the kettle would perhaps be shorter, and other disadvantages would be experienced. AS a commercial operation, the project would have to stand on its own feet,

Jan 1, 1915

By W. B. Plank

RETURNS already received from a current survey of the enrolment of students in the mineral technology schools indicate a degree of activity and prosperity in those schools never before equalled. The returns are as yet too meager for accurate analysis, but those at hand point LO considerable increase in the metallurgical and petroleum engineering groups, and indicate that the total of 5011 two years ago in the United States schools will be substantially increased. Generally speaking, the enrolment is not only maximum in quantity but optimum in quality. Better income has sent the boys back to school, but the improved employment conditions have somewhat reduced the number of graduate students. Laboratories are commonly filled to capacity, in some instances overcrowded. Increased enrolment of foreign students from both Canada and South America is noticeable.

Jan 1, 1937

By William Glenn

In their account of chromium, Roscoe and Schorlemmer (Treatise on Chemistry, London, 1879) state that "In 1762 Lehmann, in a letter to Buffon, de nova minerœ plumbi specie crystalline rubra, described a new mineral from Siberia, now termed crocoisite." In 1786 Lehmann analyzed it (Nicholson's Jour., Dee., 1798) and found that it contained chiefly lead, and that the " mineralizers " were arsenic and sulphur. It was next examined in 1189 by Macquart and Vauquelin, who stated that it contained an intimate mixture of iron, alumina, and lead peroxide. The account of their work was published over the name of Macquart. Vauquelin (Louis-Nicolas) was a Norman peasant, who had studied in the village school, and at the age of fourteen was a laboratory-boy in a pharmacy at Rouen. Later, he found his way to Paris, and in 1789 was assistant to Fourcroy, a pharmacist and a teacher of note. It was here that he met Macquart, with whom he did the work on Siberian red lead, and at this time his friend Cheradame taught him his Latin.

Jan 1, 1896

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

SME Membership Directory Listings of record March 31, 1072 SOCIETY OF MINING ENGINEERS OF AIME

Jan 7, 1972

Marius R. Campbell, Washington, D. C. (Communication to the Secretary): Having spent considerable time in a systematic study of this field,'both as regards the details of its structure and stratigraphy and the broader question of its relation to the Appalachian basin, I wish to add a word concerning the correlations made by Mr. Hodge in his paper. From A commercial standpoint, the question of correlation, even along the strike, is of little or no importance, for the variability is such that each opening should be tested individually, regardless of the horizon at which it appears; but these correlations assume an entirely different aspect when their scientific bearing is considered; they then become of vital importance, and, before being accepted, should be subjected to the most rigid scrutiny and severe tests. Mr. Hedge states positively that the Imboden seam of coal is equivalent to the Elkhorn coal of Pike and Letcher counties, Kentucky. In the writer's opinion, such equivalency is, at the utmost, only a possibility. This correlation has been generally adopted by the geologists of the Kentucky Geological Survey, but the writer has been unable to find on what grounds they base the statement. The evidence of identity seems to be in the character of the coal, as both seams furnish fine coking coal; also, in the similarity of the interval between them aid the " Bee Rock," or top of the great conglomerate. It is probably an easy matter to determine the thickness of this interval on Elkhorn creek, and we will assume that the measure of 300 to 350 feet is correct. In the Big Stone Gap field, the question of measuring the interval between the Imboden and the " Bee Rock " is exceedingly difficult. The line of outcrop of this mass of strata is along the northern base of Stone mountain, and, in the uprising of the great arch, the strata on its flanks have been thrown into many minor folds, and, in places, have been broken by local faults. This complicated structure, together with the absence of ally well-marked stratum, renders it exceedingly difficult to obtain a correct measure of the intervening sandstones and shales. The interval of 300 to 350 feet, assigned by Mr. Hodge, is mani-

Jan 1, 1893

By S. Floreen, R. M. Pilliar, H. W. Hayden

The fracture behavior of a 50 pct Cu-50 pct Fe mi-croduplex alloy, laminated composites of copper and iron and an extruded 50-50 Cu-Fe elemental powder composite was studied. Very low ductile-brittle transition temperatures were achieved in all cases, but for different reasons. In the microduplex alloy both the initiation and also the propagation of cleavage fractures appeared retarded by the very small in-terphase distances. In the composites, crack propagation through the sumples was prevented in most cases by delamination fractures perpendicular to the advancing cracks. These delaminations occurred at different regions and by different mechanisms in the various composites. In the extruded powder composite, de-lamination appeared to take place along preexisting flaws. In the crack arrest geometry of the laminated plates, delamination took place by localized shear fractures within the copper near the Fe-Cu interfaces. In this case delamination was enhanced by thicker laminate layers, and by having the resistance to shear failure of the copper sufficiently low compared to the toughness of the iron. BRITTLE fracture in engineering materials has long been a problem, and many different ways of preventing it have been considered. One method that has been of growing interest lately is to prevent crack propagation by the introduction of mechanical discontinuities into the structure. These discontinuities may act in several ways. They may simply act as crack stoppers. They may introduce secondary fractures such as de-laminations that deflect the initial crack into new, less damaging directions. Alternatively, they may subdivide a fairly large bulk sample that would have been loaded in plane strain, for example, into a number of subunits that are individually loaded in plane stress and thus are more resistant to fracture. Other mechanisms, or combinations of mechanisms, are also feasible. A number of methods exist for introducing mechanical discontinuities into a structure. Composites by their nature have discontinuities in structure, and numerous studies have shown that fracture propagation in materials of this type can be radically changed by suitable control of the composite parameters. Of particular significance to the present work are recent investigations of layered composites made by joining high strength steel sheets by various means.'-4 These studies have shown that through proper control of the mechanical properties of the bonds joining the sheets it was possible to introduce delamination fractures that markedly improved the overall toughness of the composites and in some cases completely prevented through-the-thickness fractures. Another technique for introducing structural discontinuities is simply to use a two-phase alloy. It has been recognized for many years that a small amount of a second phase may improve toughness either by homogenizing plastic flow and thus preventing localized stress concentrations that nucleate fracture, or by interacting with an advancing crack. In most of these studies of two-phase materials, the decreases in ductile-brittle transition temperatures produced by the second phase were relatively small. More recently, work on two-phase stainless steels having a very fine grain microduplex structure has shown that the presence of on the order of 40 to 50 pct of a tougher second phase may lower the ductile-brittle transition temperature of the brittle phase by approximately 300°F. 5-7 In these alloys delaminations were seldom observed. The tougher second phase appeared to minimize the ease of both the initiation and the propagation of cleavage fractures. These results show that both the composite approach and the microduplex alloy approach are effective methods of preventing brittle fracture. Therefore, it was of interest to compare the fracture behavior of a microduplex alloy with composites made from the two-phases that were present in the alloy. To simplify this comparison the 50 pct Cu-50 pct Fe system was selected for study. At low temperatures the equilibrium tie line phases in this system are essentially pure ferrite and pure copper. A 50-50 alloy was cast and hot worked to produce a microduplex structure. Two types of composites were studied; laminated structures prepared by roll bonding iron and copper sheets of the tie line compositions, and an extruded powder composite made from high purity elemental powders. The fracture behavior of these materials was then compared. EXPERIMENTAL PROCEDURE Alloy Preparation. The 50-50 Fe-Cu alloy and the components for the roll bonded composites were prepared by vacuum induction melting 30-lb heats using electrolytic grades of iron and copper as charge materials. A carbon boil was used to deoxidize the melts. Small additions of copper and iron were made to the iron and copper heats, respectively, to approximate

Jan 1, 1970

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 468.3°C (875°F). The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of their durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica (SiO2) and silicates can be melted to form glasses. Alumina (A1203), present in a mineral compound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus sand, which is generally almost pure SiO2, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide performs a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some nonminerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1983

By F. Julius Fohs

CENTRALLY located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis., because it and others of its immediate group exhibit the conditions characteristic of all. I. THE MEMPHIS MINE. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of some 350 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the bills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen.. A line of crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar-some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to limestone and calcite leaching, and the minute ones to the leaching of zinc-blende.

Apr 1, 1909

By H. E. Rorschach

Activity in the oil and gas fields of Oklahoma was more pronounced in 1935 than in 1934, with 2320 completions, an increase of about 21 per cent. The state produced approximately 185,000,000 bbl. in 1935. Osage County and shallow pools in northeastern Oklahoma showed considerable activity. The assembly of a complete table of the oil fields of the state (Table 1) was not achieved, as many of the early records of operators and pipe line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. Increased Field Activities The discovery of large production in the deep Simpson group in the old Fox field in Carter County in the southern part of the state, the discovery of new producing horizons in the Fitts pool, and the extension of Wilcox production in the "Mansion" area at Oklahoma City were the outstanding developments in Oklahoma in 1935. Wildcatting resulted in the discovery of new pools such as Jesse, Hoyt, Grayson, South Keokuk, Wofford, Britton and Stillwater. The Fitts and Edmond pools were rapidly developed during the year. Fox Pool.—Deep production in southern Oklahoma became a reality in October when the Williams No. 1 well of Carter Oil Co. and others, in the Fox pool, began producing oil at the rate of 10,000 bbl. per day from a depth of 8088 ft. After flowing wild several days, the well was killed after pipe stuck and a difficult fishing job resulted. The job had not been completed at the end of the year 1935. This test, considered one of the most important oil discoveries in the Mid-Continent area, opened the entire South Oklahoma area to a deep exploration campaign for Simpson production and production in the Pennsylvanian series on the south flank of the Arbuckle Mountains.

Jan 1, 1936

By H. E. Rorschach

Activity in the oil and gas fields of Oklahoma was more pronounced in 1935 than in 1934, with 2320 completions, an increase of about 21 per cent. The state produced approximately 185,000,000 bbl. in 1935. Osage County and shallow pools in northeastern Oklahoma showed considerable activity. The assembly of a complete table of the oil fields of the state (Table 1) was not achieved, as many of the early records of operators and pipe line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. Increased Field Activities The discovery of large production in the deep Simpson group in the old Fox field in Carter County in the southern part of the state, the discovery of new producing horizons in the Fitts pool, and the extension of Wilcox production in the "Mansion" area at Oklahoma City were the outstanding developments in Oklahoma in 1935. Wildcatting resulted in the discovery of new pools such as Jesse, Hoyt, Grayson, South Keokuk, Wofford, Britton and Stillwater. The Fitts and Edmond pools were rapidly developed during the year. Fox Pool.—Deep production in southern Oklahoma became a reality in October when the Williams No. 1 well of Carter Oil Co. and others, in the Fox pool, began producing oil at the rate of 10,000 bbl. per day from a depth of 8088 ft. After flowing wild several days, the well was killed after pipe stuck and a difficult fishing job resulted. The job had not been completed at the end of the year 1935. This test, considered one of the most important oil discoveries in the Mid-Continent area, opened the entire South Oklahoma area to a deep exploration campaign for Simpson production and production in the Pennsylvanian series on the south flank of the Arbuckle Mountains.

Jan 1, 1936

By W. A. Johnson, F. N. Rhines, W. A. Anderson

The rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish- able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1942

By W. A. Anderson, F. N. Rhines, W. A. Johnson

THE rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1941