Search Documents

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by 'oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By S. Feuerstein, J. M. Galligan

SURFACE effects in the deformation of metal single crystals have been noted by a variety of workers.&apos; A large majority of these experiments have used surface roughening or a second chemical constituent at the surface. We performed the following experiment to see how the presence of a fine polycrystalline layer influenced the stress-strain behavior of single crystals of zinc. Spherical single crystals oriented for single slip were acid-machined into cylindrical dumbbell-shape shear specimens having a gage length of 3.2 mm and a cross section of 20 sq mm. The crystals were then deformed varying amounts at the surface of the gage section with emery paper. Following this treatment, the crystals were heated for approximately 8 hr at 200°C. This resulted in a polycrystalline surface layer, with an observed grain size of approximately 1/10 mm in diameter. Deformation of these crystals was undertaken at 78°K in pure shear, the shear direction <1120> lying in the basal plane. The deformation apparatus has been described elsewhere.2 The presence of a polycrystalline layer markedly raises the first observed plastic deformation, as can be seen from Fig. 1. This yield stress is then followed by a region of low work hardening comparable to that observed in shear tests on similar untreated zinc single crystals. However, the extent of easy glide is quite seriously curtailed, and is followed by a more rapid increase in work hardening, reminiscent of Stage II observed in the deformation of fcc crystals. The higher yield can probably be attributed to the difficulty of penetrating the grain boundaries by dis locations from sources interior to the boundaries. If we associate this yield stress with this breakthrough, then we might expect that more dislocations would be trapped in the crystal than is normally the case. If there is an increased density of trapped dislocations, this could lead to an increase in the amount of trapping with increasing strain, giving a larger strain hardening in the crystal. Although other explanations can be given, it is quite tempting to characterize the region of increased work hardening as a manifestation of Stage II-type deformation. This seems reasonable if the polycrystalline layer is quite efficient in holding up a large number of dislocations. In zinc crystals, since it is well-known that the slip distance can be as large as the specimen dimensions, one would only expect to entrap a large number of dislocation with very large crystals or by applying surface layers. If this interpretation of increased strain hardening is correct, it might present a method of studying Stage II in single crystals of zinc. This research was supported, in part, by the Office of Naval Research (1959). The encouragement and stimulation given by Professor E. R. Parker is gratefully acknowledged.

Jan 1, 1965

By Clarence Balke

SMALL buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreci-able size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author&apos;s experience with a number of high-melting-point metals and with numer-ous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the- entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects clue to improper pressing can readily lead to a defective finished product. It is the author&apos;s opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By Reuben B. Ellestad, Fremont F. Clarke

Lithium chemical plant extraction methods are discussed with reference to 1) base exchange with alkali sulphates; 2) processing based on roasting with lime; 3) miscellaneous methods; and 4) application of the Lithium Corp. process to extraction of lithium from run-of-mine, low grade spodumene ore, or concentrates. IN the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2SO4) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K2SO4 is objectionable from cost considerations since purification of lithium carbonate requires the use of potassium carbonate, if the K2SO4 is to be recovered and recycled. The lower solubility of K2SO4 as compared with Na2S04 is also objectionable, since it limits the concentration of the Li2SO4 solution to be precipitated by K2SO4. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging. Other related base exchange processes are those of Lindblad, Wallden, and Sivander3 and Sivander, Gard, Villestad, and Wallen4. The former covers the reaction of lithium silicate minerals with a sodium sulphate solution, at 100" to 300°C (under pressure), while the latter involves the extraction of silicate minerals with molten sodium sulphate. Both these processes would seem to be difficult and expensive to operate.

Jan 1, 1956

By F. E. Poulson

The discovery of two new fields, Van, in East Texas, and Darst Creek, in the Balcones fault zone, is the outstanding development in 1929. The first six months was one of the most inactive periods in the history of East Texas. Five of the interior salt domes, which had been so eagerly sought as a result of the Humble Oil & Refining Co.&apos;s strike on the Boggy Creek dome in 1927, were drilled with discouraging results, and the Boggy Creek field itself had fallen far short of expectations. Kelsey, a structure of considerable magnitude and extent in Upshur County, was equally disappointing; the Amerada Petroleum Corpn.&apos;s initial test on this structure was dry. The situation improved in the latter half of the year. On Oct. 13, 1929, the Pure Oil Co. discovered the Van field. This gained for East Texas a permanent place in point of future potential production. There was a similar reaction in the Balcones fault zone. The Salt Flats (Bruner) field, the important discovery of 1928, proved its rating as a second Luling, but on account of repeated failures to extend the productive zone, wildcatting during the first half of 1929 in the Luling district was dilatory. In July, however, Darst Creek, a third fault-line field of majori mportance producing from Edwards limestone (Lower Cretaceous), was discovered. Retarded as development in this field has been by various attempts at proration, interest in the Balcones fault zone fields centered on Darst Creek as the year 1929 drew to a close. Development in East Texas Fields Discovered during 1929 Van.—The discovery well, Jarman No. 1 of the Pure Oil Co., is near the town of Van in the southeastern part of Van Zandt County, Texas. It is 55 miles northeast of the Powell field in Navarro County and 45 miles west of north from the Boggy Creek field in Cherokee and Anderson counties. Early in 1927, the Van area was submitted to seismographic exploration and outlined as a large anticline, the apex of which seemed to be

Jan 1, 1930

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 2, 1950

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.&apos; The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson&apos;s method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By Stephen Taber

JOHN C. BRANNER, Stanford University, Cal. (communication to the Secretary *).-Wideawake teachers of geology are constantly on the lookout for good illustrations of veins, especially where the processes of formation are either clearly shown or suggested. And I long ago found out that one who would learn nature&apos;s laws must despise nothing. It thus happened that in 1910, Dr. George J. Peirce of the depart-ment of botany at Stanford University called to my attention a cracked and broken yellow earthenware dish, 8 ½ in. across the top and 2 ½ in. deep, that, to the ordinary observer, seemed to be of no further use, and quite ready for the waste can. The striking thing about this dish was that the thin glaze over much of the outside surface and over the upper margin of the inside surface had been lifted in small scales, varying in. diameter from ½ cm. to 1 cm., and thrust outward and held there by some sort of white fibrous mineral. The process looked very much like one we are familiar with in the Southern States where. we often see in the winter pebbles and soil thrust out from a clay bank or lifted from a clay soil and held there supported by what is popularly known as needle-ice. Upon inquiry I learned the following facts in regard to the history of this particular dish: In the summer of 1910, it had been partly filled with a concentrated salt solution taken from one of the salterns of the Stauffer Chemical Co. at Redwood City, Cal. A qualitative analysis of the original brine showed: Present: iron, magnesium, sodium, potassium, chlorides, sulphates, nitrates (trace), bromides, carbonates, borates (trace), and considerable amounts of organic matter. Absent: calcium, lithium and iodides.

Jan 3, 1917

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth&apos;s atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

By Howard Scott

INVAR is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100° C. and soon reaches the value of copper. Guillaume1 met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detri-mental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

By Howard Scott

Invar is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100" C. and soon reaches the value of copper. Guillaumel met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detrimental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

By W. Rostoker

PART of a program of research on the Ti-A1 system1 involved a study of the lattice parameters of the titanium-rich a solid solution, which has a hexagonal close-packed structure. For this work, a 14 cm Debye-Scherrer powder camera and filtered CuK, radiation was used. For each pattern, the parameters were calculated by a least squares solution of the five strongest high angle lines. This provides an accuracy of i0.005A or better. The results are shown graphically in Fig. 1. It will be seen that an unusual change of slope occurs in the curve for the C parameter at high aluminum contents. Such anomalous changes in slope have been recorded by RaynorV or several magnesium-rich solid solutions. The effects were interpreted in terms of a special contribution to the lattice distortion due to factors of electronic origin predicted by Jones." Jones&apos; theory, in substance, suggested that an unusually large expansion of the lattice would begin when the electron per atom concentration in the alloy was increased to a value at which an overlap just began from one Brillouin zone to another. Con-

Jan 1, 1953