Search Documents

By K. R. Grube, D. N. Williams

It is often desirable to perform fatigue studies at relatively high strains and at low strain rates. A low-cost fatigue machine has been constructed for this purpose which has proven quite versatile. This machine is based on the principle of repeated bending of a strip sample over a shaped mandrel. A photograph of a group of fatigue tests in progress is shown in Fig. 1. The test sample is held in place between two shaped mandrels having a flat at their base to grip the sample firmly. A cam-driven loading frame is used to bend the sample alternately over each mandrel. The sample slides freely in this frame and is held in place by a light spring to accommodate increases in sample length. The pivot point for the loading frame is selected so as to minimize movement at the loading point during operation. The number of cycles to failure is recorded by a rachet counter which is kept in operation by a series electrical connection through the sample and is operated by the drive cam. The maximum strain imposed at the sample surface on bending from one mandrel to the other is readily calculated from the relationship, where t is the sample thickness and r is the radius of curvature of the mandrels. The rate of straining can be controlled by control of the cam speed. The device as shown in Fig. 1 is set up to run six samples at ambient temperature. A much larger number of samples can be run at one time without difficulty. ALSO-, by slight realignment of the components the mandrel unit can be enclosed in a separate chamber permitting control of test temperature and environment. This permits a variety of fatigue and corrosion fatigue problems to be studied.

Jan 1, 1963

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By Joseph Cervik

INTRODUCTION Common methods of controlling gob gas in U.S. mines are by means of ventilation of gob areas and gas drainage through surface boreholes. Costs of drilling surface gob holes increase as deeper coal- beds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States. This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1981

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By George E. Beavers

It is well to understand at once that converter gas is always mixed with copper blast-furnace gas at Copperhill before entering the Glover tower, and, at times, roaster gas is also added along with the converter and blast-furnace gas. Fig. 1 is introduced to show the variations in the sulfur dioxide content of the gas and the ability of the acid-plant operator to control the variations, resulting in a very even grade at the Gay-Lussac tower entrance. The sulfur dioxide content of the gas entering the Gay-Lussac tower must be low and regular to assure low niter consumption. The blast-furnace gas alone is rather uniform as regards sulfur dioxide content and the variations, as shown in Fig. 1, are chiefly caused by converter changes—out for charging, slag pouring, copper pouring, and, of course, the "finish." The combined gas during the converter finish is, at times, almost free of oxygen and the sulfur dioxide content reaches 13.0 per cent. At such times air is added at the Glover tower.

Jan 1, 1934

By R. J. Schilthuis, T. V. Moore

In a previous paper,' the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

BECAUSE you cannot always proceed by the ordinary pathway since you sometimes find yourself in a place where you cannot have all that you might need or wish, it often happens that it is necessary to know how to recognize and understand your materials well, in addition to having them well disposed, and to know how to use your, ingenuity in arranging a mould., Furthermore, things have a great diversity among themselves, and it is not possible to give a particular rule for all. But if you have a certain broad fundamental knowledge when you have need of many things, the ingenuity awakens and supplies its needs by imitation. Now, because I have thought that you had not hitherto had the slightest shadow of knowledge of what I have described in this treatise of mine, I have expanded and narrated things in greater detail than perhaps I might have done. For this reason I have also decided that I wish to tell you of several methods that can be used if you wish to mould, especially in making an intaglio* for a relief, t or in making another intaglio in bronze from either an intaglio or a relief. And I will tell how every relief reduces, itself from convex to concave and also how the relief is made from the intaglio. These works are first made of plaster or pastes or some other liquid thing that is soft when moulded and becomes hard either by drying out with heat or by shrinking with cold, such as tragacanth, plaster of Paris, sulphur, lead, wax, or similar things. And, in conclusion, we describe the method of making an intaglio from a solid. In making an intaglio you must first consider whether it is a large or small thing, figure or foliage, whether it is in demi- or bas-relief, and whether it is a thing that projects from the mould wholly or in part.

Jan 1, 1942

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By R. L. Frink

I FEAR that my treatment of this subject may not, in all instances, meet the approval of those who read my opinion as to the utility and efficiency of pyrometers in the making of glass, or bottle-glass. It may be superfluous for me to add that this opening statement is based on over 15 years' experience in an endeavor to successfully apply pyrometers, or heat-measuring instruments, to glass-melting furnaces, particularly the type known as tank-furnaces, and that such endeavors have proved more or less futile. It is my desire, therefore, to herein set forth the problems encountered, hoping thereby to stimulate further effort in the successful application of pyrometers. It is my desire, also, to invite criticism of the methods used and suggestions from those who may have a wider experience, or who may have better methods. Fin. 1.-GLASS TANK FURNACE. In general, I believe that the inefficient application of pyrometry to the melting of glass in tank furnaces is not due as much to the instruments as to the conditions under which they must be used and the character of the medium in which they must reside. Most of those present no doubt, are familiar, at least in a general way, with the methods and apparatus used in the melting and making of bottle-glass, or glass that is formed into containers of various shapes and designs. Most of this glass is made in what is known as a tank furnace, these furnaces vary widely in design and construction. In general, they consist of a rectangular tank-like form, built up of fireclay blocks, and range from 2 by 4 ft. (0.6 by 1.2 m.) to 24 by 140 ft. (7.3 by 42.6 m.) with a depth of glass from 2 to 5 ft.; or a capacity of from approximately. 2 to 700 tons. Fig. 1 shows the general

Jan 9, 1919

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By Joseph S. Malesky

As essential as the discovery of coal was to our state of advancement, the discovery and development of explosives marks one of the most important findings in the history of civilization. For this reason explosives are rightfully referred to as the forerunner of progress. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. An explosive may be defined as a substance (usually a mixture) that, where flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1973

By Herbert A. Stein, John B. Murdock

Perlite is a natural volcanic glass which expands into an insulation material upon the application of heat. This paper discusses the operating characteristics of eight different types of furnaces for the expansion of perlite. It also includes a section on the theory of perlite expansion which serves as the basis for the authors' analysis of the furnaces.

Jan 1, 1950

By G. H. Jardine

In future years, decision makers in the coal industry will make more and more decisions based on information from computer-based models. Whilst the use of such techniques will provide many advantages for coal companies, particularly in terms of efficient utilisation of their human resources, it is equally important for the decision makers to have an awareness of the limitations inherent in each particular computer-based model being used to provide information for the decision making process. A recommended procedure for identifying such limitations - by analysing the 3 major elements of the model - is presented. The human aspects of increased use of computer-based techniques are emphasised throughout the paper.

Jan 1, 1983

Another excellent Swedish underground crushing plant is that at Crusher Station 51 of LKAB in Kiruna, Sweden. Bottom-dump rail cars pass over a dump scroll to discharge magnetite ore into a 288 cu yd (220 m3) pocket equipped with a Hewitt Robins E-13 vibrating grizzly feeder. The grizzly section is 59 in. (1500 mm) long and has bar spacings 3 in. (76 mm) wide. Any oversize boulders which will not pass the chute opening to the feeder are blasted. The primary breaker is a Morgardshammar overhead eccentric 55 in. by 71 in. (1400 by 1800 mm) jaw crusher powered by a 200 hp (149 kw) motor. An open side setting of 10. 8 to 11. 8 in (275 to 300 mm) accounts for the high capacity of this crushing unit (2760 stph or 2500 mtph). This figure compares favorably with the capacity of many gyratory crushers but is typical of the Swedish jaw crushing installations, which are often followed by three more stages of crushing or by autogenous grinding. Crushed ore from the jaw crusher is combined with the grizzly under- size in the crushed ore pocket and is fed by a second vibrating grizzly feeder to the secondary cone crusher. Both crushers are serviced by 50/5 ton overhead bridge cranes. During maintenance operations air -operated gates shut off the flow of ore from the dump and primary crushed ore pockets.

Jan 1, 1978

By C. L. Colburn

Discovery is the first step in the location of the claim. The provision of the Revised Statutes (2320) is, " No location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located." Strictly speaking, discovery may be defined as the finding of ore or metalliferous rock in place in a well-defined vein. This definition was too strict, so discovery extended later to cover such indications of the pregence of ore, within rock in place, as would justify an experienced miner in spending his time and money with a reasonable expectation of finding ore in paying quantities. According to Colorado statutes a discovery must show a well-defined crevice; in Arizona, a lode, deposit, or mineral in place; in Montana, a well-defined crevice or valuable depositi; in Nevada, a lode or deposit of mineral in place. It is wrong to require a discovery. An honest prospector, wishing to obey the law, finds himself compelled, in most cases, to evade this point. In Clear Creek district, Colorado, a quartz seam will constitute a discovery; in Butte, a red capping; in Leadville or Ely, it is any place where a man can find a piece of vacant ground big enough upon which to sink a . 10-ft. hole. If the vein or deposit outcrops a man can show a discovery, but if it does not outcrop it is foolish to compel him to show one; and this point has been gently side-stepped. Any hole 10 ft. deep now constitutes a discovery. It is no use having laws that the people cannot consistently ob_ey. No sane man will dig unless he expects to find mineral, and he should be protected while digging. He should be required to show that he has mineral ground only when he comes to patent.

Jan 1, 1915

By Ernest Stütz

The problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenh?ttenleute at D?sseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: " The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost of briquetting a ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron." Dr. A. Weiskopf, of Hannover, admirably condenses in these words

Jan 1, 1914

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,' is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.' Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956