Search Documents

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By R. Schuhmann

As a response to rapidly growing specialization in various branches of metallurgy, it is proposed that undergraduate education in metallurgical engineering should be built up around four principal scientific themes: 1—thermodynamics, 2—structure, 3—mechanics, and 4-—rate processes. THE following quotation from a recent article by von Bertalanffyl describes very well the situation which today challenges curriculum designers in all branches of science and engineering: "Modern scientific education is presented with a well known dilemma. The amount of facts in modern science, and in any of its smallest branches, is enormous. Life in general, and the academic curriculum in particular, is short. The abundance of factual data, as well as the intricacy of modern scientific techniques, experimental and theoretical, necessitates utmost specialization. This specialization, unavoidable though it is, involves serious danger for both the education of the scientist and the social function of science. "In so far as the advancement of science is concerned, history shows that interconnection of different fields and problems is a most important basis of progress. Many of the paramount achievements of science arose on borderlines, and from the synthesis of formerly separate fields . . ." Specialization in subfields of metallurgy has become a serious educational problem only in about the last decade. The growth in specialization, almost as a necessity, has paralleled the rapid growth in metallurgical knowledge during this period. Moreover, in planning future educational policies, the educator must be concerned not only with the rate of increase in metallurgical knowledge and with the concomitant rate of increase in specialization, but also with the second derivatives, that is, with the rates of increase of the rates of increase. These second derivatives are positive and large; the growths being dealt with are self-catalyzing, or like a chain reaction. As a measure of specialization, the length of the list of different kinds of metallurgies can be considered, the kinds of metallurgy which represent one person's particular interests and those of other practicing metallurgists. To start with, there are physical metallurgy, process metallurgy, and mineral dressing, then mechanical metallurgy, metal processing, foundry metallurgy, corrosion, solid state physics, high temperature metallurgy, welding, powder metallurgy, nuclear metallurgy, etc. Each of these fields is growing so rapidly that any one metallurgist can hope at best to keep up to date in only one or two. What is the impact of all these "metallurgies" on metallurgical education and metallurgical curricula? In answering this question, it can be said, first, that educators have resisted fairly well the temptations to split up metallurgy, with different curricula, different options, degrees with different labels, and the like—degrees are still given in plain Metallurgy and Metallurgical Engineering. In other ways, though, the pressures of specialization have had noticeable effects. There is a tendency to think of these "metallurgies" as the important subdivisions of Metallurgical Engineering and to work up

Jan 1, 1956

G. B. WATERHOUSE,* Buffalo, N. -Y. (written discussion?).-One of the most essential features of rail manufacture is the production of rails that will give good service and be free from failures. To this end rails are made to careful specifications and their manufacture is controlled by rigid inspection on the part of both the producing mill and the railroad or its representative, such as the Hunt special inspection referred to in the paper. Captain Hunt refers to the crescent-shape base failures and describes them as ruptures in the rail flanges extending from the outside inward toward the web. This is hardly correct and may be misleading. It has been shown, over and over again, that the base breaks originating in seams invariably start at the center of the rail base; and run longitudi-nally in varying lengths from 3 to 12 in. and sometimes longer. Most of them are from 5 to 8 in. long and then curve outward to the edge of the flange. The split at the center of the base may exist for an indefinite time and not be discovered until the break shows on top of the flange or the piece of flange breaks off. The. stresses that cause the break are explained in two ways: (1) by the eccentric bearing of the rail base, that is taking contact at one side or edge and bringing excessive strain at the center of the base which starts fracture in any seam that may he present at that point; (2) the split may be due to cross strain in the base where this member is thrown into. compression, as happens where a pair of trucks are on opposite sides of the cross tie or rail-base hearing, and the head is put in tension. A careful study of "split base breaks" shows that fully 95 per cent. occur on the tie bearing, which is further evidence that the above de-scribed causes for the initial break are probably correct. These split base breaks are almost invariably progressive, but always start at the center of the rail-base running longitudinally.

Jan 12, 1919

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By AIME AIME

NATURE was in a smiling mood on December 18, 1883. On that day, Chester Alan Fulton, the sixty-first President of the American Institute of Mining and Metallurgical Engineers, was born, and she endowed him with every good quality within her reach - looks, physique, intelligence, and character. Brought up in the valley of the Hudson River, with the mighty Palisades which make it the "Rhine of America," he has lived up to his early promise - as a man, as an engineer and as a friend.

Jan 1, 1943

By Walter Snelling

IN the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I 'experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment.

Jan 4, 1915

By William Kent

About a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh Car-wheel Works, in malting a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and provided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0085 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam wits told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hantl-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 34,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of' the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece. must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

[ ]

Jan 1, 1942

By N. A. Gjostein

The self-diffusion coefficient D, for a surface near the (100) plane in copper was determined by means of the Mullins theory of thermal grooving, and was found to obey the Arrhenius relationship, and Do = 6.5 x 10' sq cm per sec. Suppression of surface diffusion by chemisorbed impurities encounters difliculties as a satisfactory explanation for the large Q, and Do. Instead, a model is presented which indicates that Q,, as determined by a mass-transport technique, may involve both the energy needed to form an adsorbed atom from a ledge in the surface as well as that for the movement of the adsorbed atom.; LITERATURE reviews1-3 indicate that the mechanism of self-diffusion on metal surfaces is not clearly understood. The lack of experimental data on the temperature variation of the surface self-diffusion coefficient DJ has contributed greatly to this situation. Radioactive tracer techniques4-rn have been used to measure Ds, but for many years only Nicker-son and Parker8 had determined (for polycrystalline silver) an activation energy B, and a frequency factor Do for the surface self-diffusion process. Even in this case, a mechanism could not be clearly inferred because it was suspeted7 that a contribution from volume diffusion was not taken into account by the investigators. Some later work by Li and parkere on polycrystalline gold, in which they obtained essentially the same results as for silver and in which volume diffusion could be accounted for, seems to invalidate this criticism. In 1957, Mullins10'11 developed the theory for the thermal grooving process. This advance has opened a new and promising technique for measuring the surface self-diffusion coefficient Ds. Recognizing that a thermal groove may form by several different mass transport processes, Mullins first consideredlo the cases where a) the groove forms by evaporation and condensation or b) by diffusion along the groove surface, in either case, in a system where a metal surface is in contact with only its dilute vapor phase. In a later paper," he extended the treatment to cases where the groove forms by volume diffusion into c) the solid phase or d) by mass transport through a passive gaseous phase at 1 atm pressure. The time dependence of the groove dimensions and the shape of the groove profiles predicted by Mullins' treat-

Jan 1, 1962

By Leonard Waldo

(New York Meeting, February, 1911.) THE recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high is that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, test-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful.

Jan 4, 1913

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By R. R. Jones, R. W. Kraft

Zn-Mg2Znn eutectic alloys nzay freeze willr either rodlike or lanzellar rnorphology. Alloys with slighlly more than /he eutectic arrzount of rnagnesillrn usually contain three-cnned dendrjles of MgzZnll in a eutec-lic ttlulris. All three morphologies haue the same cryslallographic orientution relationship: (0UOl) zn - 11 (111) Mg2Znll and (2310)Zn 11(101) Mg2Znll, but u3ith different prej-erred groulth direclions. The lurnellae lo rods transifion in con/rolled ingols qf euleclic cotnposition occurs because lhe large kinelic undercooling due to MgzZnll minirrzizes /he ejj-ecl of the solid-solid inlerface energy. The eutectic morphology is influenced by the presence of lhree-nned dendrites 0-f MgzZn11 which may conlrol /he rricroslrccture by acting as nuclealion sites. In recent years there has been much interest in eutectic solidification and several theories have been proposed. One of the confusing factors is the existence of various morphologies in which the solidified phases may form. The lamellar microstructure seems to be most common in metal eutectics, and it has been claimed' that all regular eutectics should be lamellar if sufficiently pure. However, there still remain eutectic alloys which are not lamellar or which change their morphology as a function of growth conditions. The eutectic between zinc and the intermetallic phase Mg2Znll was chosen for this investigation because it has been found to solidify in more than one morphology. The diagram in anssen' locates the eutectic point at 3.0 wt pct Mg and 367°C. lliott gives 364°C as the eutectic temperature, leaving the phase compositions unaltered. Since the growth conditions determine the micro-structure of the solidified alloy, the factors controlling the transition from one morphology to another could be studied. The lamellae to rods transition is of particular interest. PROCEDURE Alloys were prepared from carefully weighed portions of 99.999 pct Zn and 99.97 pct Mg by melting in Pyrex containers under argon and casting into graphite boats. The resulting ingots were remelted under argon and solidified unidirectionally in a horizontal tube furnace at growth rates ranging from 2.0 to more than 50 cm per hr under a temperature gradient, measured over a 5-cm length, of 9" to 14°C per cm. The solid-liquid interface appeared to be planar at all growth rates although no attempt was made to confirm this by decantation or quenching. A few ingots were allowed to freeze uncontrolled. Most alloys were of the nominal eutectic composition, 3.0 wt pct Mg according to Hansen2 and lliott, but some contained as much as 3.35 wt pct Mg. Chemical analyses were not run since metallographic examination confirmed that the desired composition was achieved. Specimens were cut from the middle portion of the ingot normal to the growth axis, polished mechanically, and etched with 2 pct Nital. Suitable areas were selected for the determination of crystallographic orientation relationships by a tiontechniqueof described previously by one of the authors.4 The (2310) planes of zinc and the (8701, {944}? (1032) planes of Mg2Znll were found suitable for orientation determination; experimental error was on the order of 2 or 3 deg. RESULTS Three different morphologies were found in the unidirectionally solidified alloys: lamellar eutectic, rod-like eutectic, and a structure whose most predominant characteristic was the presence of three-vaned (cellular) dendrites of Mg2Znll. These dendrites were only found in alloys with more than the eutectic amount of magnesium. In some ingots fine hexagonal needles of Mg2Znll surrounding a core of MgZn2 were observed. They were probably due to incomplete alloying and seemed to have no effect on the eutectic morphology. In addition hexagonal spirals like those discussed by Fullman and wood5 and Hunt and acksonh ere observed in some ingots frozen without directional control. Both MgZZn,, and MgZnz were detected by X-ray diffraction in these alloys. Since the morphology could not be grown unidirectionally and no characteristic orientation relationship between the phases was found, further study was limited to the lamellar: rodlike, and three-vaned dendrite morphologies. Alloys of Eutectic Composition, No Dendrites. The mcrostructures of allovs with no three-vaned dendrites were either lamellar or rodlike depending on the growth rate. At rates below 10 cm per hr the morphology was lamellar, consisting of two sets of parallel plates intersecting at about 54 deg like the Mg-MgzSn eutectic described by raft.7 At growth rates faster than 14 cm per hr the microstructure showed rods of zinc in a matrix of MgnZnll, while intermediate rates yielded mixtures of rods and lamellae in small groups. The lamellar "grains" were often several millimeters in cross section, but contained small irregular areas which divided each grain into perfect islands 100 or 200 p in diam. Lamellae were parallel to each other throughout the grain in spite of these defects in the structure, Fig. 1. Rods, on the other hand, could only be produced in small groups arranged like fish scales and separated by irregular areas of appreciable thickness, Fig. 2. Alloys Not of Eutectic Composition, With Dendrites. In alloys with 3.1 to 3.35 wt pct ME,-. three-vaned dendrites bf MgzZnll were usually found surrounded by eutectic. At growth rates slower than about 10 cm per hr the dendrites were separated from each other by small areas of both lamellar and rod eutectic, Fig. 3.

Jan 1, 1969

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By George S. Miller

Now that low-carbon steel is manufactured successfully in large quantities by the Bessemer process, and threatens to displace wroughtiron for nearly all purposes, it becomes interesting to find how its Specific gravity compares with that of wrought-iron. The general name "steel" is retained in this paper to designate that metal made by the Bessemer process, which might be more properly called " ingot iron." But the former name seems to be quite firmly established in the iron trade. This steel offers many inducements to the manufacturer of architectural iron, by reason of its hornogencity, and the large masses in which it may be readily moulded. The steel from which these determinations have been made, was produced in four-ton heats and cast into ingots of about 3100 Ibs. weight, having an average section 14'' by 14". These ingots were rolled in a blooming-mill to a section about 24" by 14", cut into slabs and rolled in a plate-mill to a plate .065" to .165" thick, and about 1411 in width. The specific gravity was obtained from pieces of this plate. The metal showed by analysis .10 to .12 per cent. carbon,.33 to .45 manganese,.060 to .072 sulphur,.075 to .082 phosphorus, and .010 silicon. The samples were not annealed, but were brought to a bright surface with a file. All figures given are averages of not less than three determinations on separate pieces from the same plate. The variation in the figures from which the averages were made in no case exceeded .015.

Jan 1, 1886

By R. V. Ramani, T. V. Falkie, T. E. Wilson

In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the interrelationships between system components and the operating environment. With such an understanding comes more exact application of simulation and other operations-research techniques to plan and operate mining systems. One aspect of the coal-winning system in need of better definition, namely, the performance of continuous miners, is dealt with in this paper. Detailed discussion of this research will be found in a report by the authors. Mining Rate The performance of continuous miners-that is, the rate at which miners can deliver coal from an underground face to the outby transportation system-is dependent upon the geometric and geological conditions of mining, the characteristics of the mining machinery, and the skill of the machine operators. In order to predict mining performance, it is necessary first to identify these factors, secondly to devise a data-collection technique, and lastly, to select a method of data analysis for drawing meaningful conclusions. Factors Affecting Mining Rate: The factors that affect the mining rate can be conveniently grouped in the following four categories: Geological Factors-The natural conditions such as seam thickness, hardness, and cleavage. Geometrical Factors-The height and width of the entries and the angle of drivage with respect to the main entries. Machine Factors-The mechanical characteristics and physical dimensions of the machine, condition of the machine, condition of the bits, and related items. Other Factors-Operator efficiency, size consist of cutter product, etc. A classification such as given here is not rigid; some of the factors can be included in more than one of the categories and some can be combined as ratios. Data Collection The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. A majority of the variables measured were continuous over a specific range of values; for example, the "width ratio" varied in practice from 0.25 to 1.00. "Dummy" values were assigned to certain operational variables in order that the variables would have numerical expression, i.e.: [ ] Data Analysis The method of analysis was to test a large model containing potentially significant variables and then reduce the model to one containing only the essential significant variables. The procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Correlation analysis, factor analysis, and regression analysis were the three statistical procedures that were used to derive the rate-generating equation. Correlation and Regression Analysis: Multiple linear correlation coefficients between all of the variables were calculated using the Pearson product moment formula along with the statistical significance of the correlation

Jan 1, 1975

By T. W. Healy, D. R. Dixon

The mechanism of activation of ZnS by metal ions and the subsequent flotation induced by xanthate has been considered as a surface redox reaction. By ultraviolet (UV) irradiation of ZnS suspensions, the normally inert ZnS is caused to react with xanthate in the absence of activator. By similar UV irradiation, the rate of adsorption-exchange of activator ions at the ZnS-H2O interface is also increased. Mechanisms of these reactions are proposed and compared to current electrochemical and semiconducting models of sulfide flotation.

Jan 1, 1976

By Frederic H. Lahee

After abandoning two dry holes, on the Mrs. Daisy Bradford land, C. M. Joiner finally completed his No. 3 on Sept. 8, 1930, at a total depth of 3592 ft. This well is 735 miles somewhat north of west of the town of Henderson, in Rusk County. Between Oct. 2 and Oct. 6, this well made numerous heads which indicated that it would produce about 300 bbl. daily. By Nov. 27, two dry holes,' completed near the Joiner well, taken in conjunction with the small production from this well, served to dampen any enthusiasm among those who hoped for a major pool; but by December 18 three other producers had been completed. On Dec. 28, 1930, E. W. Bateman's Lois Della Crim No. 1 drilled itself in with an estimated daily yield of between 10,000 and 15,000 bbl. from a depth of 3650 ft. This well, 10 miles north of the Joiner well, also in Rusk County, initiated the leasing campaign that led to the later orgy of drilling. On Jan. 25, 1931, Moncrief, Farrell and others completed their J. K. Lathrop 1 as another big producer, 7 miles east of Gladewater in Gregg County and 14 miles N. 20" E. from the Bateman Crim well. The Lathrop well, 3574 ft. deep, flowed 320 bbl. in 1 hr. through a ½in. choke. The first well completed in Smith County was Cook No. 1, drilled by Guy Lewis et al. in the James Jordan Survey, 4.7 miles west of the Joiner discovery well. On Mar. 30, 1931, it flowed 137 bbl. in 33 min, through a ¾-in. choke. The top of the pay sand was found at 3672 ft. Finally, in Upshur County, on May 5, the Mudge Oil Co. et al. completed the Richardson No. 1, which flowed 274 bbl. through a 4 2/64-in. choke in 2 hr. This well is 4 miles northwest of the Lathrop producer. Development It is unnecessary to give a lengthy description of the rapid development of the area discovered in these five far-separated wells, or to discuss the speculations offered as to whether there were several pools or only one.

Jan 1, 1932

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975

By Richard Franchot

FERROUS metallurgy today, defined as the art of extracting money from iron ores, appears to suffer from a complex of inherited theory. In so far as pig iron costs contribute to inadequate profit margins, this symptom may be diagnosed as due to persistence, despite disproval, of Sir Lowthian Bell's theories of reduction. An attempt to meet the economic situation by reducing costs through improving blast-furnace metallurgy would be inconsistent with Bell's theories. These theories, though refutable on the facts of practice, still prevail and today's metallurgy, as measured by its fuel economy or smelting efficiency ranging between 30 and 40 per cent. is no better than Bell's, showing a specific efficiency of 36 per cent.1 If fair to neglect dry-blast operations, it appears that the advance in furnace practice since Bell's day, as shown by a tenfold increase in individual furnace capacity, has been largely mechanical and that the metallurgy of the process has not been changed materially, since the introduction of blast heat, patented in 1828. It seems fair to attribute, this lack of progress on the strictly metallurgical side to a domination of the industry by false ideas first expressed by Lowthian Bell. What the furnace seems to need first, in the interest of lower costs and of better iron, is some destructive criticism of these ideas, in moderate doses, to be followed by a constructive theoretical treatment; then, research and still more research.

Jan 1, 1929