Search Documents

By L. H. Robinson

Triaxial compression tests have been performed to determine the strength characteristics of limestone, sand-stone and shale rocks subjected to controlled stress conditions. This control tuns exercised by varying the liquid pressures within and around a plastic-encased rock specimen. The pressure in the pores of the rock was varied throughout the range from atmospheric to 15,000 psig; the external pressure was changed over the same range with various positive pressure differences between is and the intertnal pressure. The data show that the rock strength increased and the mode of failure changed as the pressuire. surrounding the rock became greater than the pressure in the pores of the rock. These observations and the resu1ts of microbit drilling experiments indicate that the increased rock strength under pressure may bc an important effect in reducing drilling rare, but that other factors are probably of even greater importance. INTRODUCTION A large part of the research conductcd to reducc thc cost of drilling is directed toward improving present drilling technology and dcveloping new drilling methods. In spite of the fact that drilling is essentiaIly the act of making rocks fail, many details of the mechanism of failure are not known. It seems probable, therefore, that continuing studies of the fundamentals of rock failure can lay a foundation for future improvements in drilling technology. One of the factors which affects rock failure is the stress applied to the rock. This effect has been known for many years.'.'.; As an example, stress studics have been published by engineers' concerned with the strength characteristics of concrete in large dams. More recently, a number of investigators4-12 have explored the effects of stress on the strength of geologic formations and the geologic implications of their findings. During the last few years some research'" on rock strengths has also been conductcd in an attempt to gain additional insight into the factors which affeet rock drillability. In detcrmining the strength characteristics of rocks under different stress conditions, investigators have conventionally used triaxial compression equipment. wherein a jacketed rock cylinder is uniformly loaded from all directions and then compressed longitudinally. The results of this work have demonstrated that the mode of failure (brittle or malleable) is dependent upon the loading pressure, and that the strength of the rock increases as the loading pressure increases. These results clearly manifest that the stress, which is determined by the loading pressure, affects rock strength, and this implies that rocks under stress should be stronger and hence harder to drill. During the drilling of a porous rock the stress conditions are determined not only by the pressure surrounding the portion of the rock undergoing failure (confining pressure) but also by the pressure of the interstitial fluids within the rock (pore pressure). The importancc of both these pressures on the drilling rate of rocks has already been demonstrated by a number of investigators. Murray and Cunningham" found in microbit drilling expcriments that at constant pore pressures the drilling ratc decreased as the hydrostatic pressure surrounding an unjacketed, impermeable rock increased. Later Eckel" found that for jacketed Iimestone specimens the differcnce between hydrostatic (wellbore) pressure and formation (pore) pressure had an important effect on drilling rate. These observations of the effect of pressure on drilling rate emphasize that for drilling studies triaxial compression tests should be conducted under conditions of confining and pore pressure which simulate conditions underground. In the past, triaxial tests have been made under conditions which do not reproduce those underground. In particular, most of the tests on porous materials have keen made at varying confining pressures but with atmospheric pore pressures. In only one group of tests' was any data on the effect of pore pressurc reported, and these few data were on materials not representiltive of those encountered in drilling earth formations. The research described herein was initiated to deter-mine the importance of both internal pore pressure and confining pressure on failure characteristics of limestone. sandstone and shales. Triaxial loading equipment was used to obtain strength data at pressures up to 15,000 psig. An additional objective of this research was to apply these results to drilling rate studies by comparing them with the previously published drilling data of Murray and Cunningham" and of Eckel12. The work reported here is but one step in determining and evaluating the fundamental mechanisms which control drilling rate. Additional research is needed to clarify other aspects of the drilling process. The better

By William Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chairman of the Institute's Committee on Petroleum and Gas, as a preliminary discussion of the fuel oils which are used-in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, J suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220° F., nor burn under 320° F. In the Southwest, it has not been long since we had fuel oils that flashed at as low as 110° F., and the average flash point over a considerable period was 151° F. Now we are using oil that flashes at about 30° lower than the former burning point, which was 256° F. In other words, the flash point has risen, on the average, 100°; and the burning point about 75°.

Jan 6, 1914

By Thomas M. Price

Sand production for use in hydraulic concrete is probably the most important element affecting the physical characteristics of the resulting concrete in the opinion of most engineers, aggregate producers and contractors of today, who are engaged in the effort to produce stronger concrete per unit of cement used. Their opinion is based on both laboratory and field results. In the past, proper cement production has been the object of most of the study given this subject and while it is still studied by the extensive and well equipped laboratories that are a part of every cement mill, as well as by all governmental laboratories, at the present time the object of most of these studies has been in the field of low heat and quick setting qualities rather than the effect on the strength of the concrete. It is recognized that concrete must have two important qualities; namely, workability with the least water possible, and uniformity. These qualities have been accepted as axiomatic and possible to obtain if the foreman in charge knew his business. Now, however, with concrete produced by plants that mechanically weigh and chart all the ingredients, including water, of a batch of concrete, the foreman cannot cut and fit his aggregates, cement and water to fit his own desires and the secret of the important qualities of workability and uniformity are found to lie largely in the sand, hence the attention given its production at the present time. With this condition in mind the engineers of the United States Bureau of Reclamation and the Six Companies Incorporated in designing the plant for producing the aggregates for the Boulder Canyon Project included every possible means for the production of a sand of a constant and acceptable fineness modulus as well as a constant moisture content, and for attaining these results with as few detrimental ingredients, like silt and vegetable matter, as possible. This aggregate plant (Figs. 1 and 2) is in Hemenway Wash, 7 miles north of Boulder City. It is 4 miles upstream from the low-level mixing plant. At this screening plant 8,234,000 tons of raw aggregate are being

Jan 1, 1934

By N. I. Fisher, J. Shepherd

Statistical studies have been carried out on structural geological data collected across a large zone of roof failure 600 m (1968 ft) wide and at least 800 m (2642 ft) long in the Greta coal seam at Aberdare East Colliery. Two swarms of hundreds of minor, normal faults with throws commonly between 3 and 300 mm in the room and pillar workings are broadly coincident with roof failure. The faults have been classified into dip slip and oblique and strike slip types. Roof conditions have been classified into good; troublesome with subclasses scaly, heavy, gutter falls and wide, flat-roofed falls; and severely failed with subclasses very heavy roof, gutter falls and dome falls. Troublesome conditions are defined as those in which the height of the fall is less than or equal to 0.3 m, and severely failed conditions as those in which the fall height is greater than 0.3 m. Comparison of faults, roof condition and mining rate on a shift basis indicates that faults and roof failure are much more important than machine breakdowns in reducing mining rate. The effect of faults on roof conditions has been quantified using a concept called the "zone of influence," a rectangular area around a fault in which the fault has potentially deleterious effects. The spatial comparison of fault "zones of influence" with areas of roof failure wing Spearman's rank correlation coefficient shows that, while normal dip slip faults do not appear to be associated with roof failure, oblique slip and strike slip faults appear to be associated with roof classed as severely failed. The "zone of influence" of an oblique slip fault may extend up to 3 m on each side of it in the headings and up to 1.14 m in the cut-throughs. The fault "zone of influence" has geomechanical implications for the design of mine openings and Possibly represents the maximum length of a cantilevered roof beam likely to fail during mining, owing to a fault. Roof conditions could Possibly be predicted in blocks of &gin coal if the type of fault could be identified in oriented drill cores.

Jan 1, 1979

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947

HENRY G. MARTIN,* Chicago Heights, 111. (written discussion?).-. The object in taking three or more ladle tests is to secure a sample that will show the average composition of the heat, not primarily to investigate the lack of uniformity existing; however, the assumption that the samples are not of uniform composition -remains. In other words, we have three samples of steel of different composition, the par-ticles of which are not subject to extreme comminution so as to mix inti-mately, and yield an average homogeneous sample, if placed in one

Jan 11, 1919

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable

Jan 1, 1940

By Walter H. Munk

Generation of Waves by storms, and the transformation of waves in shallow water by local bottom topography are briefly reviewed. A detailed description of water motion in waves explains the nature and distribution of wave forces. A numerical example dealing with forces and moments against vertical piles summarizes the principles involved. Introduction The oil industry is moving into the open waters of the Gulf of Mexico. The design and construction of offshore drilling rigs present a number of difficult problems, among them problems involving the action of waves on fixed and floating structures. This paper deals with our present knowledge of ocean waves as it pertains to these problems, and the principles involved in computing wave forces against fixed structures. It is hoped that the more difficult case pertaining to floating structures can be discussed at a later time. None of the engincering aspects of the problem are entered upon in this paper, yet an understanding of the principles presented here should be helpful in the solution of practical problems. Waves are capable of exerting almost unbelievable forces. During a gale, waves at the harbor entrance of Amsterdam Canal in Holland lifted a 20-ton concrete block, which was resting on the bottom in 12ft of water, and deposited it on top of a pier which was 5 ft above the high water mark. At Wick Breakwater in Scotland, a mass of large stones in cement and bound together with iron rods, weighing 1350 tons, was broken loose and moved bodily! But one need not go to Holland or Scotland to find evidence of damage that waves are capable of inflicting (Fig I and 2). What is the mechanism by which waves are capable of exerting such enormous forces? To answer this, we must consider briefly the nature of wave motion. When a wind blows over a wheat field, waves appear to travel across the field, whereas the wheat itself remains rooted, slowly swinging back and forth. Similarly, in the case of water waves, the waveform travels swiftly over the water surface, whereas the water particles oscillate back and forth, but scarcely advance. The speed of the wave form is called wave velocity, the speed of the water particles is called orbital velocity. This fundamental difference between wave velocity and orbital velocity was already recognized by Leonardo da Vinci. Orbital velocity is generally much slower than wave velocity except for a breaking wave, a case which is of particular importance in the application to engineering problems. Forces exerted by the waves on obstacles

Jan 1, 1949

The Mineral Industry, Published by McGraw-Hill Book Co, New York, N Y. The Mineral Industry is an annual review of the mineral industry It is a standard and complete reference on the mineral industry for the year covered Through the cooperation of the A I M E its publication in 1933 was made possible Mineral Industry for 1930 contains sections devoted to the production, consumption, trade, market, uses and technology of the following headings: Abrasives, aluminum and bauxite, antimony, arsenic, asbestos (b), asphalt, barium and strontium, chromium (b), coal and coke, cobalt (b), copper, diatomite, fluorspar, gold and silver, graphite, gypsum, iron and steel (b), lead, magnesite, manganese, mica, molybdenum, nickel, petroleum and petroleum products, phosphate rock (b), platinum group metals (b), potash, precious and semiprecious stones (b), quicksilver, radium (b), uranium and vanadium, slate (b), sodium salts, sulfur, pyrite, sulfuric acid, talc and soapstone, tin, titanium and zirconium, tungsten (b), zinc, minor metals, minor nonmetals, ore dressing and coal washing (b). Sections marked (b) have appended a bibliography of recent literature on the subject. Each section is written by an acknowledged expert. Other volumes contain similar material Prices -The Mineral Industry, 1892-1930, vols. 1 to 39. Complete sets of this work, uniformly bound, except vols 25 and 26,

Jan 1, 1933

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Go., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequepce, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the " dust-bin " in the breaker, from which it is conveyed to the briquette-plant. An average analysis of the coal, published by Lewis Stockett and 13. R. Warden,' is as follows: Per Cent. Moisture,.........0.50 Volatile,..8.00 Fixed carbon,... 83..50 Ash,.......8.00 Total,.100.00 Sulphur,.........0.40 per cent. Specific gravity,...... 1.40 Color of ash,.white Heat value,.......14,000 B.t.u. The plant is run under two 12-hr. shifts, the force consisting of 1 superintendent for both shifts, 1 engineer for each shift, 1 briquetter for each shift, 1 helper for each shift, 1 laborer cleaning up for each shift. In the pitch-melting house, 2 men are on duty for one shift. The steam for the engine is furnished from a central boiler-plant, which also supplies steam for the breaker, the electric light and power-plant, machinery-shop, and boiler-shop. During March, April, May, and half of June, in 1907, the

Jan 1, 1909

BECAUSE of the impetus given to placer mining since the price of gold was advanced to $35, several types of small dredges have made their appearance, especially in the Lincoln and Oroville areas of California. Some of these are known as "doodle bugs," and have been given considerable publicity, though many believe their performance has been overrated and that complete costs of construction and operation, if known would not put them in so favorable a light. Fig. 1 is a doodle bug owned by E. M. Clark and operated near Lincoln, Calif. It is understood that it was abandoned because of inability to handle deep ground. A similar machine that has been operated-profitably by Comstock Placers is shown in Fig. 2.

Jan 1, 1938

By F. R. Archibald, C. M. Nicholson

The present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay, There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity hut they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the Property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time priding review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3,460,000 The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time Operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1949

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By Henry J. Welge

Laboortory apparatus has been devised which permits study of the displacement of oil from cores by water and by gas. The cores used contained interstitial brine as well as oil. Experiments were run to determine the comparative effect of varying the properties of the fluids used. No great effect was noted on the maximum displacement achieved. This observation made it unnecessary in initial work to use fluids in their exact reservoir conditions. Consequently, the displacements were run at near-atmospheric pressure in Pyrex glass equipment, using stripped crude oils. Introduction and Theory The chief object of this work has been to determine the efficiency of gas and water as primary agents for displacing oil from reservoir rock under laboratory conditions in which capillary phenomena were predominant. To this end the maximum displacement of oil from cores has been ascertained. This maximum displacement may not be equal to the maximum displacement from a reservoir; but it will be a close approxirnation to it sometimes, and other times the laboratory information will be useful in reservoir engineering predictions. It is] believed that the laboratory experimental maximum represents the upper limit for the reservoir recovery. The experiments were carried out by obtaining cores of interest from the reservoir, and filling the pores with interstitial brine and oil with the restored state tech- nique.1 Then the oil was displaced from the core as described later, either by brine from below, or by gas from above. The former type of displacement suggests analogy to production by water drive, but not to water flooding, for reasons discussed below. The latter type of displacement is believed to simulate production by gas cap displacement. The displacements were performed by what may be termed the capillary-pressure method. The cores are placed in capillary contact with an oil-wetted membrane which has very small pores (about I micron in diameter). Pores of this size will transmit oil but Prevent the Passage of gas or water, unless the Pressures used are higher than the capillary Pressures employed in this work. Accordingly, use of the membrane makes it possible to apply a capillary pressure differential between the displacing phase and the oil in the core. AS in the displacement of brine toward that condition of oil and water distribution existing originally in the reservoir,' it may not always be desirable to reduce the oil saturation in this experiment to an absolute minimum. With reservoirs having small productive closure, it is preferable to evaluate and use a displacing pressure no higher than the capillary pressure, Ap, which will ultimately become available for displacement in the reservoir. This pressure may be calculated from a knowledge of the density of the oil-in-place, do, the density of the displacing phase, dl, and Ah, the vertical distance between the section of the

Jan 1, 1949

By R. Ward Grosz

The Robinson mining district in east-central Nevada is itself a century of study in the changing economics of the mining business. It began as a boom and bust area. In the district today, just west of Ely, Nev., the hills are pockmarked with the tunnels and shafts sunk in a frantic scramble for gold and silver before the turn of the century. But as the economics of dwindling reserves, rising costs, and changing markets were stamping out the efforts of the gold and silver seekers, copper took over as the king of the Robinson district. Today, Kennecott Copper Corp. has four open pit mines in the district and is planning a fifth. From these mines, Kennecott produces nearly 40,000 tpy (tons per year) of copper. In its hundred years of history, the district has produced more than $1 billion in mineral values, a richer treasure than that from the more famed Comstock Lode of Virginia City, Nev. Prospectors had reported copper outcroppings in the Robinson district as early as 1872. But the first significant copper orebody was not discovered until 1901. In that year, Dave Bartley and Edwin Gray exposed the top of the porphyry orebody that would become the Ruth mine in a shaft at a depth of 120 ft. Subsequently, other larger orebodies were discovered nearby which have resulted in this area being one of the leading copper producers in the country for some 60 years. Following a period of development and exploration, the Ruth mine started production in 1915 and continued as a prosperous underground mining operation until 1948. The mining industry in Nevada experienced the same increasing cost of labor and supplies that all other mining areas had to contend with, and by 1948 the Ruth mine was no longer profitable. The mine was closed down on August 8 of that year. Now, two decades later, the mine is to produce again. The key factor in the case history of

Jan 1, 1969

FROM the first to the last meeting of t h e Rocky Mountain Club John Hays Hammond served as president. He guided its deliberations when there were any, but that always y o u n g organization was never particularly deliberate. Youth never is. And the Club was the embodiment of the youthful spirit of the West, which considers any- thing can be done if there be but the will to do it. Ham- mond and the others came out of the West, but they, brought the West with them P and in all the far countries in which he has served his profession and in all the honorable offices in which he has served his country, he lived true to the ideals under which he was raised. A Californian, born in San Francisco in 1855, the son of an army officer, Major Richard Pindell Hammond, educated in the public schools of his native city, at Yale, and at Freiburg, he turned early and quickly to mining. He served his apprenticeship as all successful mining men do, as assayer, surveyor, as assistant in ex-aminations and later as principal, and finally as mine manager. Even in those days of beginnings, his future world-wide career was foreshadowed in that Mexico as well as California served as his training school. His first major step up the ladder was in connection with the Bunker Hill and Sullivan mine, where he served in various positions finishing as president and considerable owner. It was from this great lead mine that he was called to South Africa, where he remained a number of years and was the technical expert who guided the great enterprises of Barnato Brothers and Cecil Rhodes. The story of his activity in developing the "deeps" of the Rand and in opening Rhodesia has been often told but is always an alluring one of adventure and accomplish-ment. After his famous escape from death at Johannes-burg as a member of the Reform Committee, he went first to London and later returned to the United States representing both British and American capital in the purchase and development of great mines in all parts of the world. For some years he was general man-ager, consulting engineer, and director of the Guggen-heim Exploration Co., but of recent years he has oper-ated entirely on his own account and with marked success.

Jan 4, 1928

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959

By A. O. Bartell

Do you know that valuable clues to the geology and mineralization of a district can be found in a handful of sand from a stream bed draining the area? This handful of sand has a story to tell to those who have a little patience. The handful of sand may contain tiny specks of valuable minerals (gold, scheelite, cinnabar, chromite, tourmaline-to mention a few), that will lure you upstream with the hope of uncovering a new deposit. More practically, this handful of sand can indicate the type of rocks that are exposed by the drainage system. Any mineral that has a specific gravity of 3.5 or higher can be separated from soil by panning. Garnet and pyrite, for example, can indicate an outcrop of metamorphic rock. In one district where the writer prospected, small boat-shaped orthorhombic crystals of topaz always indicated the presence of andesite outcrops.

Jan 1, 1948

By Ralph Hultgren, Prodyot Roy

Manganese vapor pressures from 1250° to 1500°K were measured by conventional Knudsen and torsion-effusion methods in twelve Fe-Mn alloys with compositions from 9 to 80 at. pct Mn. The Knudsen re-sults agveed approximately with previous measurements found in the literature which indicated the solutions were nearly ideal. However, except for the higher manganese compositions, the initial torsion readings indicated much (up to 50 pct) higher vapor presszcres than the Knudsen method. These high readings decreased steadily with time. The results are interpreted as due to depletion of surface concentration of manganese during evaporation. Thus the initial torsion readings are the most nearly correct and Knudsen methods on alloys are to be regarded with suspicion unless it can be demonstrated that diffusion rates are rapid enough to replenish surface concentrations depleted by evaporation. For the lowest manganese contents and highest temperatures, depletion causes initial torsion readings to be too low. FEW thermodynamic data are available for alloys of the high-melting transition metals due primarily to experimental difficulties at the high temperatures involved. Measurement of vapor pressure is one of the most promising techniques to be applied to this problem. From the vapor pressure of a component of an alloy phase, its activity or its partial molar Gibbs energy can be directly calculated. From measurements over a sufficient range of temperatures and compositions the partial and integral Gibbs energies, enthalpies, and entropies may be determined through Gibbs-Duhem integration. For solid phases of variable composition, which commonly are found in alloys, measured vapor pressures are low because of depletion of the surface concentration of the more volatile component as it is selectively vaporized. Diffusion from the interior tends to restore the depleted concentration. The seriousness of the effect depends on the relative rates of diffusion and vaporization. Although depletion has been recognized as a factor,' direct measurements of its rate are lacking and quantitative estimates of its effect on measurements are uncertain. In the present work the vapor pressures above a series of Fe-Mn alloys have been measured by the torsion-effusion method. This method permits a measurement of the vapor pressure of manganese as soon as the sample comes to temperature and continuously throughout the run. The rate of decline of the apparent vapor pressure measures the rate of depletion and the torsion reading at zero time should be correct. At high manganese concentrations (70 and 80 at. pct Mn), the torsion reading remained nearly constant; surface depletion was negligible. There was a slow drop in measured pressure due to bulk loss of manganese from the sample. However, for lower manganese contents, especially at high temperatures, the depletion effect was considerable and the apparent vapor pressure decreased steadily with time. For these alloys the Knudsen method should give pressures which are too low. The measurement of pressure in the Knudsen method cannot be made until enough manganese has been vaporized to be weighable. The Knudsen result is therefore an integrated average between the initial and final vapor pressures. To verify this, conventional Knudsen measurements were also made with results in approximate agreement with previously published Knudsen measurements for these alloys. As expected, for the lower manganese contents the initial torsion readings of pressure were as much as 50 pct higher than the Knudsen. THE APPARATUS The apparatus, shown in Fig. 1, is capable of operating to temperatures up to 2000°K. A vacuum of 5 x 10"6 mm Hg can be maintained. Temperatures were measured to +3° by a W-Re thermocouple placed in the dummy cell, N. The torsion cell consisted of two alumina crucibles with holes in their covers. They were placed in the molybdenum holder shown suspended from the torsion wire. Rectangular torsion wires (1 by 4 mm) were found to have superior sensitivity and less residual distortion than circular (2-mm-diameter) wires. The precision of angular measurement was found to be *0.025 deg; the variation is no doubt due to temperature fluctuation and vibration. For the Knudsen experiments the alumina cell was set on the support, N. SAMPLE PREPARATION 800-g samples were prepared by melting together electrolytic iron and electrolytic manganese and pouring the melt into a water-cooled copper mold. Melting and pouring were done under a helium at-

Jan 1, 1965

By James E. Dunn

For several years, ground support at the Pitch uranium mine has been a serious headache to the management. The "moving" ground raised havoc with standard timber sets as well as steel sets. The author discusses this problem which has led to the adoption of heavy cribbing practices in drifts and raises.

Jan 6, 1961