Search Documents

By J. L. Lytton, J. E. Dorn, L. A. Shepard

Single aluminum crystals were subjected to creep in simple shear on the (111) planes in the slip direction. The activation energies for creep were calculated from the effect of small abrupt changes in temperature on the creep rate just before and immediately following the temperature change. The results definitely establish the fact that creep of single aluminum crystals occurs by-three unique processes, characterized by thethree distinct and isolatable activation energies: The 35,-500-cal-per-mole activation energy obtained at the highest temperatures was ascribed to a dislocativationtion climb process; the 28,000-cal-per-mole activation-energy process, occurring over the intermediate-temperature range was attributed to a cross-slip mechanism; and it was suggested thot the 3400-cal-per-mole process observed below 400°K may be the Peierls energy. THE most pertinent question regarding the phenomenon of creep in crystalline materials is concerned with the identity of the crystallographic mechanisms of deformation that control the creep rate. For many years slight progress was made in uncovering the basic mechanisms for creep. Over the past 10 years, however, two parallel lines of investigations have contributed to a more definitive understanding of the processes involved in creep. The extensive development and maturing of dislocation theories for deformation of crystalline materials' proved to be of paramount importance for this progress. And second in importance was the replacement of the former prosaic methods of creep testing by new techniques'." which were especially

Jan 1, 1959

By Walter J. Karplus

By means of a finite difference expansion a fluid flow field in cylindrical coordinates with axial symmetry, is simulated by a network of electrical resistors. A series of DC analog computing units, connected to the network bounrlary corresponding to the free surface effectively adjust the network parameterr to satisfy simultaneously Laplace's equation and the borrndary conditions. The system automatica1ly "re1axes" to the correct boundary shape in a fraction of a second. A detailed application of the method to the water coning problem in oil wells is presented. INTRODUCTION The water coning problem in petroleum production is a prime example of a class of problems known as free surface problems. A free surface arises in fluid flow regions when the shape of the boundary of a single phase flow region is affected in some manner by the pressure or potential gradients within the region. When there exists an interface of two fluids of different densities, the shape of this interface will be determined by the relative velocities of the two fluids and will therefore comprise a free surface. Other free surface problems of interest to petroleum engineers include the gas coning, water injection, and gravity drainage probIcms. In each case it is desired to predict the shape of the boundary of the oil zone as a function of the flow rate, the well penetration and the physical parameters and dimensions of the system. Such problems do not lend themselves to the classical analytical treatments of boundary value problems because in this case the boundary of the potential field and the potential distribution within the field are interdependent and must be calculated simultaneously. A further difficulty arises from geometric considerations. Since the fluid flow is of the radial type in most cases, such effective methods as conformal transformation and the hodograph are not applicable. It is the purpose of this paper to present a method whereby free surface problems of this type may be solved rapidly to the desired order of accuracy by means of a combination of a network of electrical resistors and conventional analog computer units. The water coning problem is treated in some detail. Then the procedure for extending the technique to other free surface problems is indicated. FORMULATION Most commercial oil reservoirs consist of an oil-saturated sand, bounded above by an impermeable strata and below by a water-saturated sand. Gravimetric separation results in a horizontal oil-water interface. When an oil well is drilled so that it partially penetrates the oil zone, and production is initiated at a constant rate, the oil-water interface will assume a new shape as a result of the pressure gradients in the oil zone. It should be emphasized that this is a steady phenomenon. After an initial transient period the water phase will be completely static and only the oil will be in motion. The new steady-state shape of the interface, as shown in Fig. 1, depends upon the depth of penetration, d, the thickness of the oil zone, I, the production rate, q, the hydraulic permeability zone of the sand, k, the viscosity of the oil, µ, and the densities of the oil and water, p.,. and pw.. The problem is to determine this relationship. Darcy's law + = - (P f g p z).....(1) it.

Jan 1, 1957

By Robert F. Mehl

THE purpose of a symposium, I take it, is to gather together a group interested in a common intellectual field, in order to exchange views, and to appraise the state of knowledge. Symposia are the more successful, the greater the activity in the chosen field and the wider the range of applicability of the information gained. From time to time, as emphasis changes from one field of research to another, a given subject may enjoy popularity and later retire into a scientific somnolence, for fashions change even among engineers and scientists. The subject of this symposium, however, enjoys the advantages of wide applicability and of high current interest and productivity in results. It is a timely subject for a symposium; with much new information, surely metallurgical engineers should now devote an increasing attention to its application to practice. In beginning the symposium, I shall attempt briefly to appraise our basic knowledge in the field, to survey instances of practical usefulness, and to suggest where new work might be most productive of useful results. There are many examples of direct practical application of diffusion knowledge, and it is the purpose of the several papers in this symposium to review these. In this introduction I shall attempt to take a broad view, which, while it will but poorly serve the engineer in the solution of any given problem, may perhaps be of some use in assessing the state of knowledge in this field. RATE OF DIFFUSION Liquid Metals The process of diffusion among liquid metals, of gases in liquid or solid metals, or among solid metals, is ubiquitous, to say the least. The manufacture of alloys by the intermelting of metals, the addition of ferroalloys to molten steel, the deoxidation of molten alloys, all involve diffusion in the liquid state. The oxidation of molten copper for purposes of purification, the unsought oxidation of alloys generally during melting and casting, the reaction of liquid steel with oxidizing slags in the open-hearth furnace, the absorption of nitrogen by liquid steel, particularly in the bessemer furnace, all operate by the diffusion of gases in liquid metals. These processes have not been studied much from the viewpoint of rates of diffusion. Alloys are made by melting metals with stirring and with allowance of time for mixing (which is diffusion) but I know of no studies that seem to define the necessary times, and though in only very rare cases can faulty properties of the finished castings be ascribed to inadequate mixing, and though certainly in most cases, with stirring, the rate of diffusion is adequate to give sufficient mixing, a more quantitative treatment would be good to have. It is not wholly certain that thorough and sufficient mixing is at all times attained, for I suspect that ferroalloy additions to steel, and that additions of aluminum to steel as a deoxidizer, especially in the sampling of steels

Jan 1, 1944

By Caner Zanbak

Deformational behavior of a rock mass can be modeled with a constitutive law based on theories of elasticity, and plastic and viscous deformation. For most rock types, such constitutive models may be used with confidence because there is no geochemical interaction between the rock-forming minerals and water. However, if volume changes in the rock due to geochemical phase transitions are predicted, then these volume changes must be converted into mechanical parameters and must be included into the constitutive laws. In this paper, geochemical phase transitions between anhydrite (CaS04) and gypsum (CaS04-2H20) will be brought to the attention of researchers in rock mechanics. Hydration of anhydrite to gypsum may yield volume increases up to 62.6 percent and dehydration of gypsum to anhydrite may cause volume decreases up to 38.5 percent. If one were to convert the volume increases in hydrating anhydrite into strains and calculates the required stresses to restrict the expansions, the magnitude of stresses will be found at GPa levels. Such stresses on swelling anhydrite layers cannot be provided by geologic media. Therefore, the host rocks will deform under these high stresses. On the other hand, under increasing stresses, geochemical transition of anhydrite to gypsum may stop after some hydration of anhydrite, and anhydrite and gypsum systems may become stable. Changes in temperature and solution compositions in the anhydritel gypsum system also control the stability of the geochemical system, and therefore, the extent of volume changes. A similar conceptual model can be drawn for volume decreases due to dehydration of gypsum to anhydrite. In this case, stress reduction on the gypsum layer may cause extensive fracturing and changes in the state of stress in the host rock mass.

Jan 1, 1984

By G. H. Wigton

The oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods are unsatisfactory, as the lead smelters heavily penalize the largc amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this internal, an expcrimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments .were resumed. The highly infusible flotation tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent, common salt showed nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus

Jan 1, 1926

By T. F. Witherbee

The following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By Charles Larkey

NUMEROUS papers have been published on the use of graphic methods to determine the best curve to be used in estimating the production decline of oil wells but, as far as the writer has been able to ascertain, nothing has been published dealing directly with the subject as to how curves may be worked out mathematically, which will conform most closely to the production data under consideration in any given instance; hence the writer has endeavored to show by means of a few concrete examples just how such appli-cation can be made. Among valuation engineers, two types of curves are in current use for the representation of the decline in production of oil wells. One may be represented by the equation, y = krx, sometimes known as a percentage curve, for the reason that the production for any period is multiplied by a constant rate or percentage to obtain the production for the succeeding period. This curve appears as a straight line on semi-logarithmic cross-section paper. The other curve may be represented by the equation, y = kxn, and is shown as a straight line on logarithmic cross-section paper. In each of these equations, y represents the number of barrels produced over a given period of time, and x the successive periods of time. The other letters are constants to be determined for each well or group of wells considered in arriving at the most probable curve to represent the rate of production for a given property; from which the underground reserves may be estimated by extrapolation, or the extending of the curve beyond the last known period of production to show the most probable production values for the future.

Jan 7, 1923

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

The Carlin gold deposit is located in northeastern Nevada about thirty-five miles by road from the town of Elko. Following the staking of six square miles 'of ground, a drilling program outlined a fine ore body mineable by open pitting. The resulting mine turned out to be the largest open-pit gold operation in the world, until the Rosario Pueblo Viejo operation was started in 1975. Because of the high profitability forecast at the then $35 gold price, construction of a 2000 stpd mill was commenced on a crash program and was completed for Newmont Mining Corporation by Bechtel Corporation in ten months. Production was started in early 1965. The gold mineralization occurs in marine-type sediments, chiefly silt- stones and limey shales, and the ore characteristics make for a difficult materials-handling problem. At 5% to 6% moisture the ore is dusty during crushing, but even a light rain or snowfall virtually turns the material into a slurry. Crushing this sticky ore below 314 in. (19 mm) in the dry season and 1 in. (25.4 m) during the winter is extremely difficult and leads to problems with conveyors, chutes, and fine ore storage. The initial flowsheet for Carlin's crushing plant used a 5 ft by 22 ft (1.52 m by 6. 7 m) vibrating feeder -grizzly under the 60 -ton dump pocket for feeding the 42 in. by 48 in. (1067 mm by 1220 mm) single toggle jaw crusher and a 5 ½ ft (1.52 m) standard cone crusher in closed circuit with a 6 ft by 12 ft (1.83 m by 3.66 m) vibrating double - deck screen. Because continual packing of fines in the vibrating feeder pan would cause frequent plant shut-downs to remove the fines with jack hammers, the decision was made to replace the vibrating unit with an apron feeder and stationary grizzly ahead of the jaw crusher. A dribble belt was also installed under the apron feeder. This installation has greatly improved the feeding of the pit run ore to the .primary jaw crusher. Mining at Carlin is done by a 5 yd shovel and 7 ½ and 10 yd front-end loaders, and ore transport is by several sizes of trucks from 30 to 75 tons capacity. These pit haulage trucks dump onto stockpiles adjacent to the primary crusher. Ore is then fed to the dump hopper by front- end loaders only when the crushing plant is operating. This extra handling procedure is necessary because plant delays caused by problems with wet ore in the secondary crusher resulted in the ore setting up or packing in the dump pocket. Solidified material in the dump pocket would in turn delay truck haulage. The substitution of an

Jan 1, 1978

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7'his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By AIME AIME

Do you Possess, or Can you Obtain; and Will you Give, or Sell, to the Institute Library Early Volumes of the following Proceedings and Journals? American Chemical Society. American Foundrymen's Association. Australian Mining Standard. Chemical Society of London. Deutsche Chemische Gesellschaft. The Foundry. New Zealand Mines Record. Queensland Government Mining Journal. La Revue Universelle des Mines.

Jan 9, 1907

The Manufacturer's Viewpoint A prominent manufacturer of mining 'machinery not long ago expressed himself as being confident that he was securing the best kind of publicity for his product through the advertising pages of the monthly Bulletin of the American Institute of Mining Engineers. Such an expression coming from such a man is highly gratifying; yet it is justifiable when the high quality of reader and subscriber is taken into consideration. In fact, the majority of those using our advertising pages feel the same. It is to be regretted, of course, that others catering to our field do not realize the means at their disposal for presenting the points of interest of their product to the mining man. The question has been asked, " Do your members read their Bulletin?" They not only read the editorial pages, but they "admit being up-to-date enough to peruse the advertising section to "see what is new." The next question the prospective advertiser asks is, " Will the Bulletin bring inquiries?" The answer to this question holds good for any publication having as subscribers those who have purchasing or recommending power-yes, if the article advertised is not a stock one, that has been before the public for any length of time. To secure inquiries on, say, a standard centrifugal pump or any other standard product, the features of which are well known, is a most difficult proposition. Yet, of course, some inquiries are secured, but mostly from those having use for the catalogue or trade literature for reference purposes. It is safe to say that the traceable returns from advertising in trade publications hardly, if at all, pay for the advertising. The real returns are intangible, and result from the constant publicity, and keeping ?everlastingly at it." Who can say what subconscious effect is taking place when an advertisement is "glanced at," to say nothing of the effect produced when the copy is attractive and interests the reader. Time after time it has been proved that sales have been secured as a result of an advertisement, yet no inquiry had been made directly traceable to advertising.

Jan 8, 1915

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By P. G. Mason

The upswing in the price of gold in 1979 prompted renewed interest in the Mercur gold property by Getty Oil Company, owner and operator, and Gold Standard Inc. of Salt Lake City, Utah, currently retaining a 15% net profits interest. Extensive geological exploration work resumed to delineate the ore reserves, and metallurgical test work was initiated under the direction of A.H. Ross & Associates. This led to the development of an aqueous pressure oxidation process suitable for treatment of the refractory ores. Subsequent geostatistical studies revealed that the distribution of high refractory ore was less than previously estimated, and thus a higher return on investment could be realized if a direct carbon-in-leach process were used despite a sacrifice in overall recovery. This paper reviews the geological and metallurgical studies that led to this final process selection.

Jan 1, 1984

Today, the employment of the modern hammer drill, using hollow steel, with air or water to expel the cuttings from the drill hole, is the rule rather than the exception in practically all rock-drilling operations. There is considerable carelessness in the matter of keeping the hole in the drill steel properly opened. Plugged steels wholly or partially, prevent proper operation of the drill, whereby drilling speed is retarded, water tubes are bent or broken, and time is lost in tink-ering, or, as often happens, the drilling gang is idle while someone makes a trip to the shop after another drill steel or water tube. To relieve this condition, the Ingersoll-Rand Company has developed, as an auxiliary to the Leyner sharpener, a new device-the Leyner shank and bit punch.

Jan 4, 1918

By T. B. Counselman, T. B.

Continuous countercurrent decantation calculations have always been a headache to the cyanide man (and the chemical engineer) because of the simultaneous equations involved. These are tedious to solve, and there is considerable opportunity for mathematical error. This paper presents a shortcut method for making these calculations, which has been in successful use for twenty years by the author, and which is particularly valuable in selecting the best of several possible flowsheets, or evaluating the effect of various assumptions.

Jan 1, 1950

By R. E. Hurst, D. E. Ramsey, J. M. Moore

The "frac" method of well stimulation has been applied successfully to all producing formations in the Permian Basin area. During the five years since its development, many changes and improvements have been made in treating materials. procedures, and equipie11t. A number of fluid carrying agents, having different physica1 and chemical properties, have been developed to meet variorus well requirements. The current trend is toward larger gallonage treatments, employing higher injection rates. The use of "down-the-casing" techniques has greatly reduced high surface working pressures, attributable to friction losses resulting from injection throrugh tubing. Petrographic studies of various Permian Basin formations, coordinated with laboratory and well log data, have been found a valuable guide in planning frac treat111o1t.s. A knowledge of the extent (and orientation of naturally occurring fractures and planes of weakness in the formation, aid in predicting the ultimate drainage pattern resulting from the frac treatment. INTRODUCTION The South Permian Basin covers an area in Wcst Texas and New Mexico about onc-half the size of the state of Texas, This vast region has been called the "Permian Basin" for so long that the term will he used here. It includes an area south of the Matador Arch. approximately 250 miles wide and 300 miles long. Structural features of importance within the basin are the Northwest Shelf, Eastern Platform, Midland Basin, Central Basin Platform, and Delaware Basin. The principal producing formations include sand, limestone and dolo-mite, with lesser amounts of shale, anhydrite. chert. and various silicates. All of the producing formations in the Permian Basin have responded to some type of frac treatment. Essentially, a frac treatment may be defined as the injection, into a formation. of a fluid carrying agent containing a particulated solid (usually sand), for the purpose of increasing production. The application of this method of well stimulation to many differing Permian Basin reservoirs has necessitated numerous changes and improvements in carrying agents, solids, service equipment. well equipment. and treating techniques. CARRYING AGENTS A number of different types of fluid carrying agents have been developed since the introduction of the frac method of well stimulation. These agents have different physical and chemical properties, and in many cases the extent of production increase derived from the frac treatment depends on the choice of fluid carrier. Unfortunately, due to many different systems of nomenclature used in the oil field, these differences are not always recognized by the oil Operator. In general, carving agents may he divided into the following broad classi-

Jan 1, 1956