Search Documents

By R. B. Burt, James A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1-the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2-power required for pumping, 3-pump selection. The basic factors for a given problem will include: 1-weight per unit of time of solids to be handled, 2-specific gravity of solids, for calculation of volume, friction and power, 3-screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4-shape of particle or some means of determining a friction constant, 5-effects of percentage of solids, 6-development of a viscosity factor to be used in the overall calculations, 7-calculation of the lower limits of pipeline velocities permissible, 8-calculation of total head, pump horsepower, and 9-setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble, phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; -14 +35 mesh, 11.4 pct; -35 +150 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The -150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble, content of the matrix, i.e., the +14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum -velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is, smooth and- polished because of the scouring, action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump, changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1952

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By M. J. Coolbaugh

Mining of potash more than 3000 ft beneath the water-bearing sediments in Saskatchewan presented the unique challenge of designing stable mine workings and assuring protection from overhead water in a material that was believed to flow plastically, but whose behavior as a plastic material was not sufficiently known. Under the stress conditions ordinarily encountered in mining most rocks behave as elastic materials; that is, they compress slightly under pressure, and rebound when the pressure is released. Salt and potash, however, are different. Even under the relatively low pressures encountered at shallow depths, these materials become slightly plastic and yield to stress by flowing.* The plastic properties become more pronounced at greater depth and pressure, and the question arises as to whether or not the plastic flow will be rapid enough and exert enough pressure to destroy underground structures or interrupt the mining process.

Jan 5, 1967

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By Thomas, J. Elmer

WHEN the price of crude oil was advanced on July 26, 1928, with some 4,000,000 bbl. daily of potential production shut in under proration regulations, and with as much more new production shortly available from semi-proved undrilled reserves, students of the oil industry were made to realize that a new order of things now prevailed in petroleum economics. A new interpretation of the law of supply and demand had taken the place of the archaic method of influencing current production by changing crude price levels. Proration had caused the change. The long period of over-production just experienced, the prospects of a potential over-supply far into the future, had set up certain forces which brought about some fundamental changes. Their cause, effect and future influence can best be developed by a detailed study of the history of the period since war-time regulation

Jan 1, 1928

By C. E. MacQuigg

MAN?S desire to harden metal is older than recorded history and obviously would date from the moment when he found his implements were not equal to the demands of service. This need for hardness in metal may be divided roughly into two main classifications: (1 :I need for hardness through- out-for purposes of greater strength or elasticity of the whole implement or member, and (2) need for surface hardness alone. A strong steel needed to transmit stresses or resist de- formation is an example of the first class. In metals only surface- hardened, the chief need is for resistance to wear. Obviously the whole gamut of all uses can be imagined- from the extreme of a simple cantilever supporting a load in space to that of a solidly supported face plate serving to resist wear. It is the in- creasing of wear resistance which I propose to discuss.

Jan 1, 1939

By M. F. Goudge

LIMESTONE surpasses any other rock or mineral in the number and diversity of its uses and in the quantity consumed fur industrial purposes. Either in the raw state or when calcined to lime it enters directly or indirectly into the manufacture of a great variety of products and its sphere of usefulness is continually expanding. The term "limestone" as here employed includes all varieties from high-calcium limestone, consisting almost entirely of the mineral calcite, to the highly magnesian variety, largely dolomite. Lime is also discussed .because lime is simply calcined limestone and often the material may be used in either the calcined or natural state. Limestone has been of service to man since prehistoric times but only in the last hundred years has it become one of the most important raw materials in industry. In every industrial country it comprises the greater part of the total stone produc-

Jan 1, 1937

By William B. Plank

IN my studies during the past twenty years of the enrollments in the mining and metallurgical schools of the United States and Canada, I have been struck with the great diversity in the curricula offered by these schools. In 1933 when I made my first complete study of the schools (Mining and Metallurgy, May 1934, p. 211), I discovered 19 different curricula or programs of study, leading to almost as many different bachelor degrees, in the 49 schools in the United States and the 4 schools in Canada. These were: (1) Mining Engineering, (2) Coal Mining, (3) Metal Mining, (4) General Mining, (5) Mining Administration, (6) Mining and Metallurgy, (7) Metallurgical Engineering, (8) Metallurgy, (9) Petroleum Engineering, (10) Petroleum Refining, (11) Petroleum Geology, (12) Petroleum and Natural Gas, (13) Ceramic Engineering, (14) Ceramics, (15) Geological Engineering, (16) Mining Geology, (17) Economic Geology, (18) Geo- physics, (19) Fuel Technology.

Jan 3, 1950

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By H. J. C. MAC DONALD

THE mining engineer must have a chest of books snug enough for a camelback or to be stowed away in a canoe; at the lowest possible cost, as he needs it the most in those early years when he earns the least; but at the same time one having an unusually wide range, for he may have to cut down a forest, put up a sawmill, build mine towns, construct dams, power houses, power lines, and railroads. In fact he may be called upon for many unexpected accomplishments and all in extension of the characteristically broad demands of his profession. Suppose that an average mining engineer with a thorough theoretical training and a specialized mining education has accumulated, during a cosmopolitan experience, a complete and up-to-date library, but, unfortunately, in accepting a long term assignment to a far country he is forced to discard the greater part of

Jan 1, 1925

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By Elmer W. Pehrson

OPINION seems widely divergent as to where we stand with respect to future mineral supply. From some quarters we hear that the United States is about to become a "have-not" nation and about to experience the evil consequences such a situation would entail. Others claim that we are still a treasure house of stored-up mineral wealth, the surface of which barely has been scratched. The data to be presented here support the conclusion that neither of these viewpoints is correct and that we are far from exhaustion of those mineral resources that are basic to our industrial economy. However, exhaustion is well advanced in a number of important subsidiary minerals so that we can no longer drift along with the easy-going philosophy that the earth will provide. The time has come when we must recognize the true situation and do something about it.

Jan 1, 1945

By Wittenau, E.

OPERATION of a pilot mill of 100 tons' daily capacity during 1930 and 1931 proved that the copper minerals of the Colorado and Clay sections of the Morenci ore body could be successfully concentrated by the flotation process. Economic conditions caused postponement of further testing work until late in 1938 when the former No. 6 Concentrator at Morenci was converted into an experimental mill of 1500 tons' daily capacity which was known as the Test Concentrator. The Test Concentrator began continuous operation on April 3. 1939, using such crushing and grinding equipment of the No. 6 Concentrator as was appropriate. Modern classifiers and certain flotation machines were installed and later other types of flotation machines, a large grate-type grinding mill. mechanical screens, a short-head cone crusher, and a disk filter were added to the test equipment. Operation was uninterrupted until Dec. 31, 1941.

Jan 1, 1942

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

By Arthur T. Ward

WHEN the Board of Directors of the Institute in June 1931 approved the formation of the Committee on Eastern Magnetite and its then membership of eleven, little did any of those concerned envision that twelve years later the annual Committee luncheon would attract 34, and the technical session, jointly with the Iron and Steel Division, more than 70. Yet that was exactly what happened during the February meeting just passed. And what is more important, some members of the Committee are now predicting that by 1944 over 10 per cent of the iron ore produced in the United States will come from these Eastern Magnetite properties. Chairman Crockett, in opening the meeting, advised that due to the serious illness of Meredith E. Johnson, State Geologist of New Jersey, Mr. Johnson would be unable to brief his scheduled paper, which would therefore be reserved for a later date.

Jan 1, 1943

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks.

Jan 1, 1949