Search Documents

By William E. Ford, Edward Salisbury Dana

1. Normal Class (1) Galena Type 2. Pyritohedral Class (2) Pyrite Type 3. Tetrahedral Class (3) Tetrahedrite Type 4. Plagiohedral Class (4) Cuprite Type 5. Tetartohedral Class (5) Ullmannite Type Mathematical Relations of the Isometric System 50. THE ISOMETRIC SYSTEM embraces all the forms which are referred to three axes of equal lengths and at right angles to each other. Since these axes are mutually interchangeable it is customary to designate them all by the letter a. When properly orientated (i.e. placed in the commonly accepted position for study) one of these axes has a vertical position and of the two which lie in the horizontal plane, one is perpendicular and the other parallel to the observer. The order in which the axes are referred to in giving the relations of any face to them is indicated in Fig. 85 by lettering them a,, a2 and a3. The positive and negative ends of each axis are also shown.

Jan 1, 1922

By Horace Winchell

SCOPE OF DISCUSSION THE laws here referred to Are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry.

Jan 4, 1914

By L. M. Cathles, H. R. Spedden, E. E. Malouf

Fluid flow through an igneous rock formation will occur mainly through fractures. A non-diffusing or slowly diffusing tracer (such as .5µ silica spheres identifiable under electron microscope) will arrive at a monitor well when enough fluid has been injected to displace the volume of water in the flow fractures between the injection and monitor wells. A rapidly diffusing tracer (such as NaC1)-will diffuse into the matrix blocks and so a volume of tracer nearly equal to the total fluid volume contained in the rock formation between injection and monitor wells must be injected before significant diffusing tracer arrival will be noted. The flow fracture porosity is typically one hundred times smaller than the total porosity of an igneous formation. The shift between diffusing and non diffusing tracer arrivals, together with the diffusional characteristics of the tracers, can define the diffusional accessibility of the matrix blocks of an igneous formation. A field test of these concepts and the problems encountered will be described.

Jan 1, 1974

By James M. Schopf

Coal petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petrographic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures.

Jun 1, 1956

By R. H. Singleton

ThE purpose of this investigation was to determine the effect of cerium upon the nonmetallic inclusions found in cast and wrought steel containing various amounts of sulfur, oxygen, and nitrogen. Interest of the Physical Metallurgy Laboratory of the Watertown Arsenal Laboratories in this type of research was stimulated by the reports from industry that rare-earth metals imparted beneficial effects upon the mechanical properties of steel, but that the mechanism was not understood. Berry and Dorvel' found that misch metal improved the impact properties of aluminum-killed cast steels. They reported that the rare earths modified the intergranular-film type nonmetallic inclusion, present with aluminum as the sole deoxidant, to a randomly distributed globular type. Lilliequist and Mickelson2 observed the improvement of ductility and toughness of quenched and tempered cast steels through rare-earth additions. They also observed the change from angular to duplex inclusions when rare earths were present. They con-

Jan 1, 1960

By Louis A. Panek

Caving of previously undisturbed ground was conducted for a period of about 20 months at two locations about 600 m (2000 ft) apart in an Arizona porphyry copper deposit. When mining was suspended the width of the mined zone at both sites was on the order of one-half the depth and the thickness of ore extracted was only a fraction of the rock column. Thus the results have potential application to predicting the subsidence above a cavern-type excavation. Break cables were used to detect the upward progress of caving. Analytical aerotriangulation was used to determine the vertical and horizontal displacements of 400-plus surface targets covering a 1585 m (5200 ft) square area. The measurements are summarized and interpreted with a view to predicting the rate of rise of a caving brow, detecting the initial surface subsidence, and characterizing the extent, the location, and the varying degrees of expected damage to surface facilities.

Jan 1, 1984

By R. L. Dietrich

[ ] We at The Dow Chemical Co. have recently done some work on the deformation of magnesium alloys and although it is far from complete there have been a few observations which may be of interest in connection with this paper. In the first place, I should like to point out that the deformation of polycrystalline magnesium alloys has not been completely explained by the work on single crystals. Bakarian and Mathewson found slip on the ( 101) and {002) planes, and (102) twinning as the deformation mechanisms in magnesium single crystals, but in compression when the (002} planes were within ii° of parallel t0 the compression surfaces, fracture occurred at all temperatures up to 340°C (644°F). In commercial working processes, particularly in rolling, an orientation is quickly produced which should be unfavorable to further deformation by the three established mechanisms. The first few reductions in rolling quickly produce an orientation having

Jan 1, 1947

By AIME AIME

OPPORTUNITY may not be knocking but it, at least, is waiting for you, your family and your friends in that amazing republic south of the Rio Grande. For the first time we are able to publish the official itinerary for the forth-coming Mexico City meeting of 1936. As shown on Page 351, the deluxe special train leaves St. Louis on Thursday. Nov. 5 at 5:30 p.m., returning to St. Louis on Nov. 18 at 8:15 a. m. The schedule provides seven days and six nights in Mexico City with numerous excursions to nearby towns and resorts. The oldest surviving city in' North America is Mexico City, dating back at least to the twelfth century. It was the Aztec capital when Cortez arrived in 1519. The famous cathedral still standing was built on a foundation of sculptured Indian images and the remains of a great Aztec temple. Today it is a city of romance.

Jan 1, 1936

By I. D. Hagar

WHEN the history of American business during these momentous war years is written, an absorbing chapter will be devoted to the Maclntyre Development, in northern New York. It will tell of a timely mining project, deep in the wilds of the Adirondacks, blasted into being by Axis torpedoes. It will recount the labors of 1500 engineers and workmen, miles from a highway, rail line, or power source, who built a huge enterprise in a few short months' time. And it will list these major contributions to the war effort: more than a quarter million tons per year of ilmenite, source of titanium dioxide-man's most opaque white pigment-to be used in paints for warships, tanks, guns, planes and the plants that build them; as a co-product, over 500,000 tons each year of magnetite-an important type of iron ore- to help feed the cavernous maw of America's wartime steel industry.

Jan 1, 1942

By THOMAS J. CLIFFORD

IN 1926, finer grinding began to be a feature of the milling practice of the Southeast Missouri lead district. Nothing since the adoption of flotation has caused greater changes and greater improvement in results. The trend toward finer grinding, with the consequent discarding of tailing at finer sizes, and consequent lower assays in lead, continued to progress until 1931, when the abnormally low price of lead brought a halt: that is, the better metallurgical results obtained would not offset the increased costs due to higher power and necessary maintenance. Since 1931 a slight tendency toward the discard of coarser tailing has taken place. , In 1926, larger rod mills i.12 ft. 1 in. by 6 ft. 6 in.) than any previously used in the district were installed in cue plant, and a new primary crushing plant, of greater capacity was built. This combination demonstrated immediately the better metallurgical results obtainable by finer grinding and all the mills now running have adopted the practice.

Jan 1, 1934

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By J. F. Myers, F. M. Lewis

DISCUSSION L. E. Djingheuzian (Canadian Dept. of Mines and Technical Surveys, Ottawa)—In their Summary the authors say: "Reconciling the grinding efficiency with good metallurgy is still a problem." In the discussion of the first paper8 in his reply to W. I. Garms, Mr. Myers states: "Our grinding process with smooth I-in. balls has reduced by nearly one half the metallic losses in the fine micron sizes of the tailing. This is simply because less of the fine micron sizes are produced. Since the + 65 mesh size is the same as formerly, a higher percentage of the intermediate sizes are developed. These sizes have the highest floatability, require the least reagents, and use less floating time. "These factors contribute so heavily to the overall economies that dropping our power grinding gain from 28 pct back to 19 pct is a small detail. However, we feel that this is only a momentary situation and that eventually the best features of the grinding and flotation processes can be brought together, which is as it should be." Italics are mine. The above statements, to me, appear to be the answer to the opening statement in the Summary. Denoting the costs at different power grinding gains as: Power Grinding Power Grinding Gain, 28 Pct Gala, 19 Pct Cost of grinding G G1 Cost of flotation F F1 Value of metallic losses T T1 where G1 > G2 F3 < F, and T1 < T, we have: G1+Fl+T1<G +F+T. Since the authors accept the idea that "grinding in flotation plants becomes part of the &apos;conditioning&apos; of the feed to flotation",4 i.e., that in flotation the ball mill is primarily a conditioning machine, it can be postulated that Tennessee Copper grinding at cost G1 is more efficient than grinding at lower cost G. This can be directly inferred from the Conclusion of the paper. Mr. Myers also emphasizes this at the end of his reply to Mr. Garms: "that grinding is for the purpose of preparing flotation feed and not grinding per se." This, to me, in the final analysis means that when the efficiency of grinding is weighted against the conditioning factor, the former becomes a function of efficient conditioning, hence, within the system in which proper conditioning is the dominant factor, the best grinding efficiency is provided by grinding which will contribute towards the optimum conditioning. This brings us again to the statement: "that if every grinding unit were considered as a conditioner for each following step, efficient grinding plants would become much easier to design."&apos; In other words, grinding equipment should be balanced against the flotation equipment and against chemical reactions taking place in the system. F. C. Bond (Allis-Chalmers Mfg. Co., Milwaukee)— The authors&apos; discussion of the probable ball motion in a slow speed high dilution mill is very interesting. When the 1-in. balls have worn down to about one fourth of their original weight they apparently first develop a flat surface; as wear progresses this flat face becomes concave, and other concave faces appear. It seems more probable that the first flat face may form at the softest part of the ball surface, and that each succeeding contact tends to force this flat face into sliding contact with a larger round ball; than that the flat faced ball tends to pair off with a particular round ball and to travel with it continuously. When the small worn ball has a flat face and is in sliding contact with a large round ball, the surrounding large balls will assume a more or less definite pattern, and slide against the worn ball, thus producing secondary concave faces. The primary concave face seems to be larger and better developed than the secondary faces. The ball charge can be divided into "concaves" which show at least one concave surface, "intermediates" which have developed flats or incipient concaves, and "rounds." Ball slippage is always present in a tumbling mill, and the mutual ball movement is necessarily a combination of rolling and sliding. The sliding motion is apparently concentrated upon the smaller worn balls which nest between the surrounding larger round balls. When each worn ball starts its upward path in the mill its primary flat or concave surface fits against a larger round ball, and the round ball slides upon it. The action may be something like that of the ball separator in a ball bearing, except that the worn sliding balls are always under considerable pressure. The material is ground under the combined influence of breakage 1—by impacts between falling balls and between falling and supported balls, 2—by being nipped between rolling balls, and 3—by being rubbed between the sliding balls. The rubbing action will be increased in the presence of worn balls with concave surfaces. The rubbing action probably produces a considerable portion of the finely ground slimes in the product. The worn balls commonly approach tetrahedrons in shape, and are very different from concavex, each of which has two equal opposed concave surfaces. Concavex were designed only to grind upon themselves, and not for use in combination with grinding balls. Their action in a grinding charge is very different from

Jan 1, 1952

By A. A. Collins

H. R. BIANCO*—I should like to ask Mr. Collins if that statement he made about the addition of drosses to the blast furnace slowing down the blast furnace is a result of his own experience or a result of the experience of some older metallurgists; and perhaps I should ask him to define the type of drosses that he means. A. A. COLLINS (author&apos;s reply)— That has been my own personal experience with dross. On various occasions at Chihuahua we attempted to incorporate the dross in our regular blast furnace charge and to shut down the dross re-verberatory to try to save some money. As expected, we had very poor results. I think that Ed Fleming will well remember on one occasion, that was back about 1933, when we attempted the first experiment along this line, and as a result of the sulphur addition to the blast furnace to matte out the copper we ended up with hanging furnaces and mushy slags and abandoned the dross experiment, once again turning to the use of the reverbera-tory for handling dross. H. R. BIANCO—Is that dross you refer to from the drossing kettle ? A. A. COLLINS—Yes, the dross that I am referring to came from drossing kettles. Furthermore, to back up my previous assertion, I had occasion in 1943, while up at Leadville, to once again experience the routing of dross through the blast furnace with its sulphur addition, since they had no dross re-verberatory, and to observe that once thf dross was removed, the furnace was speeded up almost 100 tons a day. All of these are personal experiences and I think that Mr. Feddersen also has had a little experience along this line —in fact, I believe all of us have had some experience. H. R. BIANCO—I know at Trail they recirculate considerable dross through the blast furnaces and we also recirculate dross at Herculaneuin and I am not aware that it has done much towards slowing down the blast furnace. A. A. COLLINS—We have always had very poor results. In the first place you have got to add a sulphur addition to pick up that copper and once you do that, that sulphur is apt to combine with some of the zinc and you are going to form a little mush; before you know it you have furnace hangs and a poor working furnace. Now of course that depends on the amount of zinc you have on charge. But in 1943, Leadville had roughly about 7 pet zinc in their slag and it worked very poorly. Previously when they had 4 or 5 pet zinc in their slag it did not matter. B. L. SACKETT* At Tooele we had a great deal of experience with copper. We have always been able to keep a lead well, however, in spite of the fact we have run as much as 5 pet copper and only 15 pet lead on the charge. But regarding the handling of dross, our dross reverberatory furnace is only 7 or 8 years old. Before that we recirculated the dross through the furnace and thought we were doing a pretty nice job. Of course these things are all more or less relative—in other words you establish a certain condition much better than one of a few years ago and possibly as good as any other of which you know and you think you have pretty good results. When we first took the dross off of the blast furnace and put it through the dross reverberatory furnace we immediately found out that we had gained something very real in furnace speed. Since that time there have been occasions when, because of the dross reverberatory being down, we have had to use dross again through the blast furnace and that has checked our original experience in slowing down the furnace very definitely. So we feel that a dross reverberatory is a very valuable asset at the Tooele Plant. A. A. CENTER*—Mr. Sackett&apos;s being here reminds me of trying to run with a minimum of lead concentrates the maximum of dross producing electrolytic zinc plant residue. He came up from International Smelting Co. to help us get started on that. We took an old copper blast furnace at Great Falls, Montana, and made a lead furnace out of it by putting a lead well on the other long side which of course is a very unorthodox lead blast furnace. Our aim was to treat the residue from the electrolytic zinc plant, as I said, with a minimum of lead concentrates. That meant a maximum amount of dross. At that time selective flotation was not general practice, so our zinc concentrates ran relatively high in copper and other dross-producing elements; and of course these were largely in the zinc plant residue. I think we might call it muscle metallurgy, but we had an interesting, successful experience there and we ran for over a year thanks to Mr. Sackett&apos;s helping us get started. I have the details, but time does not permit. We did well enough so that the A. S. and R. Co. at East Helena kept boosting up the offer to us for the electrolytic zinc plant residue and there was not enough lead concentrate to supply two lead smelters there in Montana, so the matter finally finished up by the A. S. and R. Co. taking all of the residue under long term contracts.

Jan 1, 1950

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.&apos;TheRittinger In its first form, as stated by P. R. Ritted.&apos;tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin&apos; as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

The effects of aeration on an aqueous suspension of pyrrhotite were studied and their results correlated with flotation tests using xanthates as collectors. The effects of copper activation and of pH variation were determined and possible mechanisms postulated. PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents,3 or by starch.&apos; The object of this work was to study the floatabil-ity of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH. Preparation of the Pyrrhotite Sample: It was desirable that the highest grade of pyrrhotite obtainable be used for this experiment, since the presence of other minerals could affect the surface properties.5 However, no pyrrhotite was available as crystals, and massive deposits of hydrothermal origin commonly contain considerable amounts of chalcopyrite. Pyrrhotite concentrate was, therefore, prepared from a sulphide deposit occurring near Aitkin, Minn. The deposit is of pyrometamorphic nature consistirlg mainly of pyrrhotite and pyrite with graphite, silicates, and carbonates as gangue. The ore, already crushed through 3 mesh when received, was screened at 65 mesh and the undersize discarded. The oversize was crushed through rolls, and then stage-ground dry in an Abbe porcelain mill, the —65 mesh portion being screened out after every 15 min of grinding until all the material passed through this size. The ground product was then concentrated with a drum-type dry magnetic separator. The rougher concentrate was cleaned twice and then demagnetized. The final product was split in a Jones splitter and stored in air-tight bottles. Microscopic examination of the concentrate showed that it was relatively clean and free of pyrite, locked particles, and gangue. By means of the krypton gas adsorption method," the specific surface was determined to be 3000 cm2 per g. The chemical and screen analyses of the final concentrate are given in Tables I and II respectively. It is a well-recognized fact that the oxidation of some sulphide ores during stockpiling, grinding, and conditioning affects their flotation behavior. The problem of oxidation may become serious in the case of pyrrhotite, since this is known to be more easily oxidized than many other sulphides. To ascertain the extent of oxidation, an experiment was carried out by aerating an aqueous suspension of pyrrhotite with air, oxygen, and nitrogen as follows. A 300-g sample of pyrrhotite in 2700 ml of water was agitated and simultaneously aerated in a Fager-gren-type laboratory flotation machine. A Precision wet test meter was connected to the air inlet valve, the flow rate of the gas being kept constant at 0.3 cu ft per min throughout the experiment. Samples of approximately 30 ml each were taken from the cell at 0, 4, 10, 20, 35, 60, and 90 min. After the pH was taken, each sample was filtered and the filtrate was analyzed for total iron and sulphur. The iron was determined colorimetrically by the thioglycolate method using a green filter.&apos; The filtrate was oxidized with bromine to convert all of the soluble sulphur compounds into sulphate and this was determined with a Parr turbidimeter." When aeration tests were made in alkaline circuit, calcium hydroxide or sodium hydroxide was added at regular intervals to maintain a constant pH. A similar procedure was followed in an experiment to determine the abstraction of copper. ion by pyrrhotite. In this case various quantities of cupric chloride were added. The filtrate from each sample taken was analyzed for copper, total iron, and sulphur. The carbamate method with a green filter was used for the copper analysis,&apos; since this method could tolerate a considerable amount of iron in the solution. A pneumatic cell, made from a 350-ml fritted glass Buechner funnel, was used for this experiment. The detail of the assemblage has been described elsewhere." In the present work a stainless steel baffle was inserted in the cell. This baffle overcame the tendency for the coarse pyrrhotite particles to be swirled around the wall of the cell and thus fail to collect in the froth. A 50-g sample of pyrrhotite was added to the cell which contained 260 ml of water. When pretreat-ment of the sample was desired, reagents, such as activator and pH regulator, were then added and the pulp was conditioned for a specified conditioning time. Prior to the addition of the collector approximately 15 ml of the solution were removed for pH measurement and for iron and sulphur analyses. Copper when used as activator was also determined. Collector and frother were then added and the pulp was conditioned for an additional 2 min. Air was admitted to the cell and the froth removed. The separation required from 4 to 6 min, depending on the characteristics of the froth. The float and non-float products were filtered, dried, weighed, and assayed for iron.

Jan 1, 1955

By C. B. E. Douglas

The following analysis was stimulated by a previous article on evaluation of the water problem at Eureka, Nev., which describes a method using formulas especially devised to calculate flow potential of extensive aquifers characterized by relatively even porosity and permeability throughout. The present discussion submits that the method was unsuitable for solving the kind of problem occurring at Eureka, where the amount of water available, rather than the flow potential, may have been the vital factor. IN an interesting article on evaluation of the water problem at Eureka, Nev.,1 W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner&apos;s prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem. The two formulas Mr. Stuart used, the Theis formula and the one developed from it by Cooper and Jacob, were given field checks a number of years ago in valley alluvials by the Water Supply Div. of the U. S. Geological Survey and found to be reliable when the aquifer is very large in horizontal extent and sufficiently isotropic for the test well and observation wells to be in material of the same average permeability as the saturated part of the aquifer as a whole." Extensive valley alluvials, sands, and gravels can be evaluated in this way, and there are even cases in which the method could apply to porous limestones, such as flat beds of very large areal extent that have been submerged below the water table after extensive weathering. These are sometimes prolific sources of water for towns and industries. It is necessary for them to have been above the water table for some geologically long period of time in a fairly humid climate before submergence because the necessary high porosity and permeability, and large reservoir capacity, are the result of weathering, that is, of solution by the carbonic acid (H,CO3) in rainwater formed by the absorption of CO, from the air by raindrops, and this dissolving action must cease when all the H2CO3 has been consumed by re- action with the carbonate to form the more soluble bicarbonate. Consequently this weathering process is largely restricted to a zone that does not extend much below the water level, and submergence is necessary after the weathering to provide large reservoir capacity and good hydraulic continuity. On the other hand, water courses tend to form along faults and fractures in limestone, and to become enlarged by solution, well below water level when, as often happens, fresh meteoric water is circulated rapidly through them to considerable depth by hydrostatic pressure, as through an inverted syphon. Although the reservoir capacity of such water courses is relatively small they may extend far enough to tap more prolific sources. Cavities, and sometimes caves of considerable size, are found in limestones where the acid formed by the oxidation of sulphides has attacked them. This action can take place as deep below water level as surface water is carried by syphonic or artesian circulation, because the oxygen it carries in solution will not be consumed until it reacts with some reducing agent, such as a sulphide. Moreover, the formation of acid and solution of limestone in this way is not confined to the immediate vicinity of the sulphide. Oxidation of pyrite, for example, results in formation of acid in several successive stages, each taking place as more oxygen becomes available, as by the accession of fresh water into the circulation at some place beyond the sulphides. When the acid thus formed attacks the limestone, CO, is liberated and the ultimate effect of the complete oxidation of one unit of pyrite will be the removal of six times its volume of limestone as the sulphate and bicarbonate, both of which are relatively soluble. The reaction may be continued or renewed along a water course far from the site of the sulphides, where the small electric potential produced by contact with the limestone helped to start the reaction. Mr. Stuart refers2 0 caves in the old mining area in the block of Eldorado limestone southwest of the Ruby Hill fault at Eureka, Nev., and to the cavities encountered in drillholes in the downthrown block on the other side of the fault. Although he interprets these cavities as evidence that this formation was sufficiently isotropic (evenly porous and permeable) to give reliable results by the method he describes, they may, in fact, be entirely local conditions. There is reason to think they were probably formed

Jan 1, 1956

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed&apos; in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported&apos; that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory&apos; is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The&apos;evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By L. Thomassen, N. Spooner, J. M. Thomas

NI-CR and some Ni-Cr-Fc alloys, when used as electrical resistance heating elements in reducing atmospheres, at times suffer rapid breakdowns due to so-called "green rot." These reducing atmospheres are most frequently used in bright annealing and heat-treating furnaces which are kept for long periods of time at 1500&apos; to 1800°F. The green rot is a preferential oxidation of the chromium in the alloy to such an extent that the remaining metal frequently becomes ferromagnetic. The Curie point (magnetic transition point) at room temperature for a pure Ni-Cr alloy is known to be at about 7 pct Cr.¹ This represents a severe loss in chromium for one popular grade of resistance alloy, which is nominally 80 pct Ni-20 pct Cr. The formation of oxides along the grain boundaries makes the ribbon brittle and gives the fracture a green, earthy appearance—hence the name. The authors have studied this phenomenon, simulating the industrial conditions by heating resistance ribbons in various reducing atmospheres, such as moist hydrogen or the atmosphere specified in the ASTM test.² This atmosphere contains 16 pct H2, 10 pct CO, 4 pct C02, 1 pct CH1, 1.5 to 2.5 pct H2O, balance N2. Little success was had in producing severe corrosion with the commercial 80 pct Ni-20 pct Cr alloys. It had been noticed, however, that 90 pct Ni-10 pct Cr alloy wires deteriorated very rapidly when placed in the bottom of narrow thermocouple protection tubes. The bottoms of the tubes with the wires were heated in air. This took place both in porcelain tubes and in Inconel* tubes either with the cold end open or loosely stoppered with asbestos. On examination the wires showed microstructures which would be classified as green-rot corrosion. Subsequent investigations with various alloy wires confirmed the observation that corrosion occurred in some wires, including 80 pct Ni-20 pct Cr alloys, much more rapidly in such tubes than had occurred previously in test atmospheres mentioned above. When 90 pct Ni-10 pct Cr alloys are oxidized with an abundant air supply, the oxide coat consists of both nickel and chromium oxides. In this case thermodynamic equilibrium between the oxides is not established. However, when oxidized 90 pct Ni-10 pct Cr alloy specimens were heated to 1500" to 1800°F inside small diameter tubes, the oxide coat transformed to a bright metallic outer layer of nickel or nickel-rich alloy, beneath which appeared a green oxide, followed by intergranularly attacked metal. The obvious explanation is that in the narrow tubes, thermodynamic equilibrium is being established according to the equation NiO + Cr (in alloy) ? Ni + Cr2O3 This reaction is favored due to the fact that the oxygen pressure over nickel oxide is more than 10"&apos; times the oxygen pressure over the green chromium oxide. The initial oxygen in the tubes is depleted very rapidly by oxidation of the wire and of the tube, if it is metallic. A confirmation of the occurrence of the reaction, reduction of NiO by the chromium in the alloy, was obtained by putting oxidized nickel foil into an evacuated quartz tube along with a piece of bright 90 pct Ni-10 pct Cr alloy ribbon, and heating the tube at 1820°F for a number of hours. The nickel oxide on the foil was completely reduced to pure nickel, leaving a bright foil. The 90 pct Ni-10 pct Cr alloy became strongly magnetic and showed the typical green-rot structure. Weights of the samples before and after testing showed the weight loss of the foil to approximately equal the weight gain of the ribbon. Evidently the bottom of long, narrow protection tubes, stoppered or not, may under certain conditions act just as the sealed quartz tubes in respect to being a confined space in which oxygen is not freely replenished. This condition of oxygen depletion can be prevented by introducing a small amount of air into the bottom of the tube. Many conditions becloud the green-rot phenomenon, such as carburization, sulphidization, and the presence of other corrosive agents. However, these experiments have shown that the basic reaction is a case of internal oxidation which can occur simply by adjusting the oxygen pressure to a low enough level so that the atmosphere will leave the nickel intact and oxidize the chromium. The action of the other agents in commercial atmospheres can then be taken up as individual cases. From these and numerous other tests completed to date or still in progress, it is believed that a more critical evaluation of electrical resistance alloys for their resistance to green-rot corrosion can be made. A much better understanding of the mechanism for this type of corrosion should also result. A more complete report on these experiments will be published later. In the May 1953 issue: TP 35213 Discussion: Solubility of Carbon and Oxygen in Molybdenum by W. E. Few and G. K. Manning, discussion by N. A. Gokcen: p. 747, first column, the fifth, sixth, and seventh lines should be the first, second, and third lines, followed by the present first, second, third, fourth, eighth, ninth, and tenth lines.

Jan 1, 1954

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.&apos;TheRittinger In its first form, as stated by P. R. Ritted.&apos;tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin&apos; as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953