Search Documents

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By V. Carlson, J. A. Rowe, E. O. Bennett

This report concerns the microbial flora found throughout the surface facilities of six water-injection systems in Texas and Oklahoma. Each system is described in detail and water quality data are presented when available. Pseudomonads and sulfate-reducers (Desulfovibrio) were the predominate organisms found in the systems. The genera Sphaerotilus, Bacillus, Achromobacter, Minococcus, Clostridium, Flavobacteriurn, and Sarcina were also isolated in significant numbers. Molds, iron bacteria, sulfur bacteria and soil bacteria were found less frequently in the systems. It is concluded that a complex microbiological flora exists in oilfield water-injection systems. A tendency for waters to deteriorate in passage through solid bed filters is also noted. INTRODUCTION The injection of water into a subsurface formation is often accompanied by numerous problems, the origin and nature of which are only partially understood. During the past few years, investigators have indicated that bacteria are involved in some of these problems even though very little specific information is available concerning this matter. It is surprising that investigators working on microbiological problems in water injection have never made a complete study of the flora of these systems. The logical course to pursue is that of identifying the microbial flora and then examining each organism individually and in combination with others to determine if they produce a particular problem. The objective of the present investigation is to identify the microbial flora in water-injection systems. In addition. the quality of the water in most of the systems was determined and some observations made on the extent to which passage through surface-handling facilities affects water quality. The information derived from this study can serve as a foundation for additional basic investigations. EXPERIMENTAL PROCEDURE The microbial flora of six water-injection systems were studied at 50 sampling points. These systems are experiencing problems which may be attributable to micro-organisms, and two were being treated with antimicrobial agents at the time of this study. The samples were obtained by inoculating 1.0 ml of the water onto the different media at the sampling point. The media used for primary isolation included nutrient agar, Strokes agar, M-10-E medium and semi-solid thioglycollate medium. The cultures were returned to the laboratory, incubated at 30°C until growth occured; then, pure cultures were obtained from individual colonies. The pure cultures were identified according to standardbacteriologica1 procedures. Those organisms not fitting identification criteria exactly, even though exhibiting close similarities to known species, are listed as unidentified organisms. Membrane filters were used to make water-quality tests at intervals before and after collection of the microbiological samples. The filter discs were 47 mm in diameter with a 0.45-micron particle-size retention, and the tests were done under closed conditions at 20) psi. Membrane flow rates are plotted as increasing filtrate volumes, and the total solids contents arcs given when available. An effort was made to sample at each place in a system where a change in environment occurred. In this manner, the effect of passage through filters, tanks, hay sections, etc., on the microbial flora and water quality could be observed. RESULTS SYSTEM A This waterflood system (Fig. 1) is about four years old and daily pumps approx&ately 110,000 bbl of oil-free sour water from a 3,700-ft deep reef. The

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By C. E. Coleman, D. Hardie, A. E. Wraith

A photoguaplric method of measuring crack velocities has been applied to an examilzation of- the effect of hydrogen on the impact properties of zirconium. Results indicate that the crack in hydrided zirconit travels at about 26 m per sec whereas that in the uacuum -annealed is dependent on the speed of the hammer. RECENT work on the effect of hydrogen on zirconium reveals that when hydrided zirconium is tested in slow bending the crack producing failure can be unstable. The mode of fracture seems to involve the crack linking up broken hydrides by a ductile mechanism in the zirconium matrix.2" In order to compare the fracture of zirconium with that of other metals which show unstable crack propagation, notably steel, the rate of the crack spread must be known. As the methods previously used for measuring crack growth are either unsuitable for the present work5-'' or very costly," a simple technique has been devised in which the maximum crack velocity is derived from a series of crack position-time measurements. EXPERIMENTAL PROCEDURE The experimental arrangement is shown schematically in Fig. 1. The flash unit12 was triggered when the Charpy hammer touched the specimen and the 6-psec flash of the lamp delayed by a preselected time interval in the range 100psec to 10 msec. The camera was left on open shutter during the test. From direct measurement on a calibrated photographic print, Fig. 2, the position of the crack and the specimen was found at a known time after impact and, from a series of such tests using an appropriate range of flash-delay times, the crack velocity was estimated. Preliminary experiments were carried out on mild steel above and below its transition temperature. Vacuum-annealed zirconium, and zirconium hydrided to 100 ppm H were then tested at 20" and 150°C. For comparison, Zr-2.6 pct Nb alloy (in the 0 + transformed /3 condition), vacuum-annealed or hydrided to 100 ppm H, was tested at 20 C. The chemical analyses of these materials are given in Table I. For the high-temperature tests a fine chromel-alumel thermocouple was spot-welded onto each specimen close to the notch. The test piece was heated up to 200°C to allow enough time for preparing the apparatus while the specimen cooled to the testing tem- perature. It was assumed that the specimen cooled uniformly. The accuracy of the flash-delay time was better than i2 pct i 5 psec. The crack length was taken as its maximum distance traveled normal to the length axis of the specimen. Errors in these measurements arise as a result of the uncertainty in the location of the crack tip and the difficulty in defining the exact position of the crack starting point. The latter was due to the bonding and large amounts of deformation at the hammer contact point, especially in the vacuum-annealed specimens tested at 150°C. The maximum error in the measurements was however estimated to be about 5 pct. DISCUSSION OF RESULTS From the trial experiments using mild steel above its transition temperature it can be seen from the plot of crack length against time after impact, Fig. 3. that a reasonable estimate of the maximum crack velocity at the surface of the specimen may be made. Other features of note are the initiation time before the crack is first seen and the slowing down period

Jan 1, 1967

By C. A. Hartnagel

During- the past 10 years the annual production of petroleum in New York has averaged close to 5,000,000 bbl., the total for the period being 49,881,000 bbl. In 6 of the 10 years, the production was slightly in excess of the 5,000,000 mark. The 1944 production of 4,697,000 bbl. represents a 7 per cent decline from the previous year. Of the total 1944 output, the Allegany County district, which includes two small areas of Steuben County, contributcd 3,614,065 bbl., a decline of 5 per cent from 1943, and the contribution of Cattaraugus County, which represents the northern extension of the Bradford pool of Pennsylvania into New York was 1,082,935 bbl., a decline of more than 14 per cent. Since March 1942, the posted price of New York crude oil has remained at $3.00 per bbl. On lug. I, 1944, a Federal subsidy of 75¢ per bbl. was granted to oil producers, thus making the price actually $3.75 per bbl. Since all of the oil produced in New York comes under the designation "stripper well operations," it is entitled to the Federal subsidy. During the last few years there has been little change in the number of wells drilled annually. In the Allegany field, which accounts for three fourths of the oil produced in the state, 1240 wells, including water-intake wells, were drilled during 1944 as compared with 1223 in 1943. There was no marked increase in the number of wells drilled after granting the subsidy of 75¢ per bbl. of oil on Aug. I, the increase being but 14 wells during the last half of the year over the preceding six months. In flooding operations it is not to be expected that even a substantial increase in the price of crude oil will be reflected quickly in an increase of the number of wells drilled or in a marked increase in production of crude oil. In flooded areas, oil is obtained through a program extending over a number of years. This program involves the drilling of the water or input pressure wells, drilling of the oil wells, building up the oil flood to maximum production, and finally the watering out of the well when the amount of oil produced in proportion to the water becomes so small that pumping is no longer profitable. The various operations may extend over a period of 10 years or more, during which time the price of crude may have fluctuated greatly. Although the rate of production can be controlled to a limited extent, it is evident that a flood when once begun must be continued regardless of the price of crude. During the past seven years New York crude has had a price range from $1.68 per bbl. in 1938 to the present price of $3.75 per barrel The field pattern now in general use for wells in a flood project is the "five-spot." Under this arrangement, the lease is divided into squares with a water well at each corner and an oil well in the center. In the all-over pattern of the lease each oil well is acted upon by four water wells and each water well supplies part of the pressure to four oil wells. Spacing between the input water wells and the oil wells usually varies from zoo to 225 ft. or, on an acre basis, there is one oil well and one water well for each 2 1/2 acres. In recent years there has been a tendency to increase

Jan 1, 1945

By Irving B. Cadoff, Ernest Levine

The fracture path in a Cu-4 pct Ag alloy wet with mercury was found to he dependent on the heat treatment used prior to tensile testing. Both quenched and slow-cooled alloys were embrittled by the mercury.. For quenched alloys, which were single -phase, the crack path was intergranular. Slowly cooled alloys, which contained precipitate platelets, exhibited transgranular fracture. By comparing stress-strain data for these alloys with similar data on mercury -embyittled solid-solution alloys, it was found that the role of the precipitate and that of the grain boundary in the fracture process were equivalent . THE fracture path which results when metals are strained in a liquid environment appears to be dependent upon the nature of the specific system. Mixed transgranular and intergranular cracking has been observed in the 2024 T4 aluminum alloy when wet with a Hg-Zn amalgam.' Transgranular fracture was induced in an A1-4 pct Cu alloy by masking off the grain boundaries from the liquid Hg-Zn amalgam.' The embrittlement of solid-solution alloys of copper in mercury results in intergranular fracture.' The effect of a precipitated phase on the fracture path in copper alloys is the subject of the present investigation. Cu-4 pct Ag was chosen so that its behavior could be compared with previous work on embrittlement of copper alloys. PROCEDURE High-purity copper (99.999 pct) was used as a base metal, along with 99.999 pct purity silver. Melting was carried out in graphite crucibles with manual agitation to get adequate mixing. The ingots were homogenized by means of vacuum annealing, chemically cleaned, and cold-rolled with intermediate vacuum anneals, to the desired thickness of 0.025 in. The rolled sheets were sheared to the final specimen size of 1 by 0.025 by 0.1 in. The specimens were then electropolished in phosphoric acid (concentrated) and heat-treated in an evacuated capsule at the solution temperature of 770°C. One batch was slow-cooled and the other quenched in water. The thermal etching which occurred during heat treatment was sufficient to permit grain boundary and precipitate delineation. Tensile tests were carried out in air and in mercury on a Table-Model Instron at a pulling speed of 0.2 in. per min. Wetting was accomplished by electro-polishing in phosphoric acid, rinsing in alcohol, and immersing in a pool of mercury. Once wet the coating was stable throughout the mechanical tests. In our studies it was found that wetting the surface or total immersion in mercury produced identical results. For convenience, the wetting technique was used for the experiments described. The crack pattern was observed directly on the surface by removing the mercury after testing. De-wetting was accomplished by flame heating the samples in a vacuum after testing and before observation of the surface. No etchant or polishing was used so as not to obscure the crack pattern on the surface. The mercury removal, however, resulted in a pitted surface but otherwise left the pertinent features visible. Photomicrographs were taken in this condition so as not to disturb the structure associated with the crack pattern. The average precipitate spacing was measured previous to coating the sample with mercury by use of an optical eyepiece micrometer. RESULTS The microstructure of the quenched specimens was single-phase while that of the slow-cooled specimens contained thin platelets of a second

Jan 1, 1964

By H. A. Wahl

This paper presents methods of designing hydraulic fracture treatments in formations saturated with slightly compressible liquids. Howard and Fast describe the fluid-loss control resulting from the viscosity and compressibility effects of the reservoir fluid in terms of a fracturing fluid coefficient. However, for horizontal fractures, this coefficient is applicable to infinitely thick reservoirs. These methods of evaluating fluid loss from horizontal fractures during treatment differ from previous methods in that: (I) formation thickness is incorporated in the velocity function describing the rate of fluid loss to the formation; and (2) for a given thickness the relative position of the fracture to the horizontal boundaries of the reservoir or any interrnediate permeability barrier is incorporated in the design procedure. This theory is applied to several actual and hypothetical field cases. The results of these calculations demonstrate that the eflect of formation thickness on fluid loss from horizontal fractures may result in fractures several times larger than predicted by other methods. INTRODUCTION Hydraulic fracturing has been the dominating well-stimulation technique during the last decade. From the time it was commercially available, fracturing has had a very favorable success ratio compared to other stimulation methods. However, numerous wells that were successfully stimulated remained economic failures. Only in the last few years has the oil industry recognized the importance of designing treatments for each well which will yield the maximum profit. This implies that for a given set of treatment conditions the size and general physical characteristics of the fracture can be determined. One of the outstanding contributions in the field of fracture design was presented by Howard and Fast.' In their paper, three flow mechanisms that control fluid loss from the fracture to the formation are defined: (1) viscosity effects of the fracturing fluid, (2) viscosity and compressibility effects of the reservoir fluid, and (3) wall-building effects of a treated fracturing fluid. The rate of fluid loss to the formation adjacent to a fracture is shown to be a function of time. For each flow mechanism the velocity function v(t) is expressed as a constant or fracturing fluid coefficient divided by the square root of time. This form of v(t) can be used in the Carter equation, as developed in the Howard and Fasc paper, to estimate the areal extent of fractures. This equation may be written as In the following sections the effect of formation thickness on fluid loss from horizontal fractures is evaluated when the controlling flow mechanism is the viscosity and compressibility of the reservoir fluids. The major assumptions inherent in the Carter equation are brought out in subsequent mathematical developments. THE EFFECT OF RESERVOIR FLUIDS ON FRACTURE EXTENSION When a fracture treatment is performed using a fracturing fluid identical to the reservoir fluid, the only flow mechanism controlling fluid loss is the viscosity and compressibility effects of the reservoir fluids. In developing a fracturing fluid coefficient for this mechanism, Howard and Fast considered a segment of the formation bounded by a unit area on the fracture face and extending to infinity in the direction of leak-off as shown in Fig. 1(a). The direction of leak-off z is normal to the fracture face. The equation governing the linear isothermal flow of fluid into this segment is where a = Eq. 2 is a form of the diffusivity equation. It is derived from the equation of continuity, Darcy's law and Eq. 3

The performance of a two-horizon depletion-type reservoir produced through combination wells is analyzed. By introducing some simplifying approximations, it has been possible to obtain formulas which are easy to handle. Only ordinary differential equations are used, and the development of the analysis can be followed without difficulty by the non-specialist. A rigorous analysis has been made of this problem. It has been found that the approximations introduced in the simplified analysis are fully justified and that errors seldom will be more than 2 per cent. The report shows the effect of the rate of withdrawal upon the relative depletion of the two horizons. Numerical examples are given. INTRODUCTION In its simplest form an oil reservoir consists of a continuous, homogeneous body of porous and permeable rock, enclosed at the top and the bottom by impermeable material. The flow of fluid through such a reservoir has been the subject of numerous papers, and the mathematical analysis of well performance, pressure build-up, etc., has reached a high degree of refinement. One of the basic assump tions introduced into these analyses is the homogeneity of the reservoir. In non-homogeneous reservoirs, these computations still can be carried out satisfactorily, provided small irregularities in the physical properties of the rock are distributed in a random fashion. The flow equations are derived as solutions of the continuity equation, and their solutions are dependent upon the assumption of many constant factors in the reservoir: permeability to oil, compressibility of the reservoir fluid, viscosity saturation, etc. When these axe assumed to be constant, the continuity equation can be solved rigorously. When these assumptions do not hold and corrections are introduced, it becomes very difficult and often impossible to solve analytically. The present analysis is concerned with production from a two-layer depletion-type reservoir in which the layers have different permeabilities. Instead of using the continuity equation, results were derived from some simple physical ideas. In a single-layer reservoir in which the oil is at a pressure above the bubble point, the rate of production often has been assumed to be directly proportional to the pressure drawdown. In the simplified analysis it has also been assumed that the drop in average reservoir pressure is directly proportional with the cumulative withdrawal. These considerations in the past have been the basis of the analysis of reservoir performance and have been applied to a variety of problems, often with marked success. In the problem under investigation these relationships are shown to be compatible with the equation of continuity, but the approach has the advantage of leading to ordinary differential equations in which changes in constants can be introduced without making the analytical solution impossible. It has the additional advantage that it can be understood more readily by the large group of engineers who are not reservoir specialists. For that reason, detailed steps in the mathematical developments have been shown in full. SCOPE OF ANALYSIS The analysis in this paper has been applied to a two-layer depletion-type reservoir in which both horizons are produced simultaneously in the same well. Because of the difference in permeability, it is obvious that the depletion of the two zones will proceed at different rates. For various problems it may be of interest to know the degree of depletion of the two zones at any arbitrary time and to in-

By R. A. Salathiel

A new synthetic material has been developed which is highly effective in treating drilling muds to reduce filtration rate. The material is the soluble salt of a very high molecular weight condensation product of sulfonated phenol and formaldehyde (SPIF). Laboratory tests show that SPIF is effective in muds of all salinities varying from fresh water to saturated salt water. Alkaline materials. such as soda ash or caustic and quebracho, may be used in combination with SPIF to advantage, and are essential in muds containing saturated salt water. In a field test where the water used in the mud had a salinity of about one-half that of sea water, SPIF in combination with caustic and quebracho made a very satisfactory mud. SPIF does not ferment. but due probably to additional polymerization a slight decrease in effectiveness is found when it is subjected to high PH and high temperature for a long time. INTRODUCTION Drilling mud is essential in rotary drilling. The influence of variations in the different properties of a mud on its ability to perform the various functions in drilling of wells is thoroughly understood in some cases and poorly understood in others. For instance, the function of mud density in restraining high pressure fluids is simple and well known. On the other hand. while the value of low filtration is widely recognized, it is seldom possible to determine precisely what filtration rate is required for the mud to perform its functions properly. Filtration rate is important because it influences the ease of moving tools in or out of the hole. Filtration rate also affects the stability of the bore hole walls, which are subject to softening and degradation by aqueous filtrate. Difficulties in rotary drilling are often avoided by using low-filtration muds. Treatment of fresh-water muds to provide moderately low filtration rates usually consists of adding chemicals to improve the dispersion of the clays. To provide very low filtration rates, organic colloidal materials are added. Among the materials hat are used in this way are starch, natural gums, and altered celluloses. In muds that contain large amounts of salt or calcium or magnesium ions, the clays are coagulated and, as a consequence, the filtration rate is undesirably high. In such muds organic colloids are of great importance. LIMITATIONS OF PRESENT FILTRATION ADDITIVES Starch and water-soluble gums are widely used as filtration control agents. Starch is the most important material of this kind being used. It has the advantage of relatively low cost. It is effective in promoting low filtration rates, not only in fresh water muds, but also in muds containing large amounts of salts. However, both starch and natural gums are subject to fermentation and must be preserved from damage caused by microbiologic attack. Also, both starch and natural gums tend to increase the mud viscosity undesirably. Furthermore, the quantity of material required may be quite large. This is especially true when substantial amounts of salts are present. In such a case small addition* of starch may increase rather than reduce the filtration rate of the mud. Carboxy-methyl-cellulose, a chemically altered form of cellulose, has some advantages over starch. It is effective in smaller concentrations and does not increase the viscosity as much as

Jan 1, 1952

By N. Pessall, A. D. McQuillan

The phase relalionsllips in an isothernzal section of the Ti-Zr-H system at 750°Chave been investigated by measurement of hydrogen equilibrium pressures. The resulting diagram indicates that the hydride phase has an anomalously wide range of homogencity extending from 66.6 to 30 at. pct H in alloys containing about 15 al. pet Zr. Measurement of the heat of solution of hydrogen as a function of alloy composition in ß-phase alloys indicates no anomalous behavior in the region of 15 at. pet Zr, and suggests that the extensive range of homogeneity in the hydride phase at about this composition must he attributed to an enhanced stability of the, hydride phase. THE manner in which titanium and zirconium react with hydrogen and the constitutional diagrams of the two metal-hydrogen systems are qualitatively very similar,'-6 as can be seen from Fig. 1 which shows the constitutional diagrams of the two systems. Quantitatively, however, there are some differences. For example, the exothermic heat of solution of hydrogen in ß titanium is smaller than that in ß zirconium, and consequently the equilibrium hydrogen pressure of a Ti-H alloy is higher than a Zr-H alloy at the same temperature and hydrogen concentration. Other differences manifest themselves in the hydride phases which exist at high hydrogen concentrations. In the Ti-H system, above room temperature, there exists only a single hydride phase in which the metal atoms are arranged on a fee lattice, but in the zirconium system there are two hydrides, and whereas the hydride of lower hydrogen concentration has a fee structure, the higher hydride has a face-centered tetragonal structure. The tetragonal hydride retains its stability up to temperatures in excess of 450oC.7 From the foregoing, it would be expected that the constitutional diagram of the ternary Ti-Zr-H system would have a very simple form, especially as titanium and zirconium are completely miscible in both the a and ß forms.8 The present work, which consists of a study of an isothermal section of the ternary system, was carried out in order to check the assumption frequently made that the electronic structure of the two metals and the mechanism by which hydrogen is held in solution in the metals is the same for each. Although this proved largely to be true, certain inter esting and unexpected features of the ternary system emerged which must be explained before we can really say that the reactions of titanium and zirconium with hydrogen are fully understood. EXPERIMENTAL PROCEDURE The most convenient method of studying hydrogen-metal systems is by the measurement of the hydrogen pressure in equilibrium with the hydrogen dissolved in the metal as a function of hydrogen concentration and temperature. In binary systems, the results are easily interpreted in terms of alloy constitution, since two-phase regions can be recognized by the fact that the hydrogen pressure at constant temperature does not vary with the hydrogen concentration in the alloy when it is in the two-phase condition. This criterion does not apply in ternary systems, but there is usually a marked change of slope in the isothermal pressure-composition curves when a phase boundary is crossed, and with care, and a knowledge of the limiting binary systems, the phase structure of the alloys can usually be deduced. In the

Jan 1, 1962

By L. K. Nemeth, H. T. Kennedy

The investigation presented in this paper was performd to develop a relationship between the dewpoint pressure of a hydrocarbon reservoir fluid and its composition, temperature and characteristics of the heptanes-plus fraction. This is part of an over-all program to develop correlations for the essential properties of reservoir fluids with the composition, temperature and pressure. In all, 579 dewpoint pressures, determined experimentally on 480 different condensate systems along with their compositions and temperatures, were obtained from the literature and from previously unpublished sources. Compositions were expressed in terms of mol fractions of methane through heptanes-plus, nitrogen, carbon dioxide and hydrogen sulfide, and the molecular weight and specific gravity of the heptanes-plus fraction. Distribution of the samples assured a good representation of most of the major oil-producing areas in the world. A multiple regression analysis program written for the IBhl 7094 digital computer was used to compare numerous equations and to calculate their coefficients. The final equation containing 11 coefficients resulted in an average absolute deviation of 7.4 percent for all the samples. Segregation of data on the basis of one or more variables did not materially improve the results. The correlation developed is useful in predicting the dewpoint pressure of condensate reservoir fluids from variables normally measured in the laboratory. INTRODUCTION In any discussion of the dewpoint of hydrocarbon mixtures, it should be noted that there are two kinds of dewpoints which must be distinguished. The first type, or normal dewpoint, usually occurs at low pressures as dry gas is compressed to the point where liquid first forms. The second type, sometimes called the retrograde dewpoint, occurs when a gas mixture containing heavy hydrocarbons in solution is depressured until a liquid is formed. The first type, as applied to condensate mixtures, would normally be below atmospheric pressure and would be of no interest in reservoir performance. The second type is of great significance in interpreting reservoir behavior and is the property referred to throughout this paper. Laboratory measurement of dewpoints is laborious, expensive and subject to many errors, and it is desirable to find a reasonably accurate method to predict dewpoint pressures from the composition and other readily available properties normally measured on the fluids. A possible method of calculating dewpoint pressures would be to employ a set of equilibrium ratios (K-values). 1 However, the K-values themselves depend on composition as well as temperature and pressure; presently their use adds nothing to the accuracy of predicting dewpoints. If future correlations provide a significantly better method of estimating K-values for heavy hydrocarbons, they may be of greater use. REVIEW OF LITERATURE In 1944, Olds, Sage and Lacey 2 studied the behavior of fluids from the Paloma field. Properties of seven mixtures were studied at temperatures ranging from 100 to 250 F and at pressures up to 5,000 psia. From the information obtained, the influence of composition and temperature upon the dewpoint was determined. It was found that removal of the intermediate molecular weight components from the mixture resulted in considerable increases in the dewpoint pressures. Results indicated that the effect of changes in temperature was relatively minor when compared with the effect of modifying the mixture by removing the intermediate components. Thus, removal of propane and butanes resulted in an increase in dewpoint pressure more than 10 times greater than a change in temperature from 100 to 250 F. The authors stated that althouah

By T. R. Ingraham

When aluminum sulfate was decomposed in an evacuated apparatus and the sample cooled, Q alumina was found. The thermodynamics of the decomposition reaction were resolved by measurements of the total pressure of SO3, SO2, and O2 generated over the sample at various temperatures. The results were correlated with other published data to calculate the rmges of thermodynamic stability of the various compounds involved. The thermal decomposition of aluminum sulfate was studied by Wijhler, Pluddeman, and Wöhler1 and by Warner and Ingraham.2 The results of both studies were critically reviewed by Kellogg,3 who observed that "each set of data shows considerable scatter and strong curvature on a plot of log pso3 vs 1/T".3 He agreed with Warner and Ingraham2 that both the discrepancy in the two sets of results and their curvature may arise from the indefinite properties of the particular form of A12O3 which is formed during the decomposition. While studying the thermal stability of other sulfate systems, we had noted the presence of nonequilibrium oxide properties in both the cobalt4 and manganese5 systems, but neither had shown any appreciable curvature on a logPSO, vs 1/T relationship, and the data from both systems agreed reasonably well with prior work. It therefore seemed reasonable to reexamine the technique which had been used in our earlier work on aluminum sulfate.2 The principal difference was that a tightly compacted pellet had been used for the earlier aluminum sulfate work, whereas a loose powder, contained in a platinum boat, was used for our work on other sulfate systems. In addition, a better technique had been developed for dehydrating the samples. From work done on the nickel system,6 we had become aware of the highly protective nature of some sulfate layers on their oxjdes, and hence of the necessity of providing a large surface area of P3e sample when equilibrium was to be attained in a reasonable time. That observation suggested that perhaps a steady state, rather than equilibrium, had been reached in the earlier work on aluminum sulfate. This paper reports a repetition of the experimental work with large, finely divided samples of anhydrous aluminum sulfate. APPARATUS AND PROCEDURE The apparatus used in the experimental work was described in earlier papers.2,7 The source material was Anachemia reagent-grade Al2(sO4)3 - 18H2O which was first partly dehydrated by heating at 400°C for 48 hr and then completely dehydrated by repeated baking of an aluminum sulfate-oleum slush to dryness at 450°C. ? Alas was prepared by decomposing some of the sulfate in a muffle furnace at 800° C overnight. Approximately equal amounts of the 7) alumina and aluminum sulfate were used in the experiments. The finely divided samples were handled under dry box conditions, and in addition some of the aluminum sulfate was decomposed in the apparatus while it was under vacuum, to ensure its complete dehydration prior to sealing the apparatus. The samples were heated to a series of constant temperatures on both increasing- and decreasing-tem-perature programs. Two to three days were required to obtain steady readings of the total decomposition pressure on an increasing-temperature program, and 5 to 6 days on a decreasing-temperature program. Three samples were examined on both programs. Within experimental error, the results for each sample and each program could not be distinguished.

Jan 1, 1969

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.' Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers' continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.' Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.' Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.' The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company's mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By H. D. Attra

The effects of phase behavior on reservoir economics is a function of both fluid composition and flow properties of the reservoir rock. In some operations such as gas injection into volatile crude-oil resertoirs, the stock-tank recovery derived from vaporization of the reservoir oil by the displacing gas can approach the recovery derived from the displacement mechanism. In other cases of gas-cycling reservoirs, the dry injected gas can effectively vaporize a retrograde liquid phase, allowing a substantial reduction in cycling pressure with no appreciable loss in recoverable liquids. Because of these effects, it is essential that phase behavior be considered in developing the economics of any secondary recovery program in which gas is the injected fluid. The inclusion of phase behavior in conventional calculation procedures has been retarded because of the complexity of the calculation and the large volume of laboratory data required. However, by applying high-speed computers and new laboratory techniques, the phase-behavior displacement calculation has been developed to economically include this basic fundamental of gas displacement. The calculation is performed by reducing the reservoir to a series of one-dimensional segments. Phase changes, saturation distributions and changing fluid properties are evaluated for each segment as a function of time. The relative volumes of equilibrium liquid and gas displaced from each segment are determined by a trial-and-error procedure to meet the requirements of phase equilibrium and two-phase flow. The produced fluids are flashed through conditions of surface separation approximating those in the field to obtain actual values for stock-tank liquid recovery and producing gas-oil ratios. Based on the results of successful field studies, the technique appears to have application to reservoirs producing under a nonmiscible gas-displacement mechanism and should substantially increase the reliability of this type of analysis when phase behavior is an important factor. Predicting reservoir performance under gas-injection operations involves three basic principles of reservoir engineering. First, a material balance exists between the displacing gas and the displaced reservoir fluid. Second, the oil and gas flow in relationship with the two-phase flow property of the reservoir rock; and third, phase equilibrium exists between the displacing gas and the native reservoir fluid. To illustrate these three principles, consider the one-dimensional reservoir shown in Fig. 1. The reservoir is divided into a series of segments representing a one-dimensional cross section between an injection area and a producing area. So represents the oil saturation, Cw represents the connate-water saturation and Sg represents the displacing gas saturation. The gas is moving into Segment 1 and the reservoir oil is being produced out of Segment N. Consider the case when gas has just moved into Segment 1 and the displacing gas-oil contact is at position a-a The volume of oil pushed out of Segment 1 is a function only of mobility and the two-phase flow properties of the reservoir rock, that is, Kg/Ko and µo/µg. Behind the front if the injected gas is foreign to the reservoir oil (a nonequilibrium gas), there will either be vaporization of the oil into the gas or condensation of the gas into the oil. In either case the net result is a mass transfer and a re-distribution of composition and liquid and gas saturation. If the displacement is at constant pressure and is continued, the gas moves into new segments, proceeding succesively into Segment 2, 3, etc. The total volume of oil produced from the reservoir

It has been established that molybdenum sesquisulphide, not molybdenite, is in equilibrium with molybdenum metal and sulphur vapor in the vicinity of 1100°C. The S2 pressure for this system has been obtained using the Knudsen orifice method and the standard free energy for the dissociation of S2. THIS work was undertaken to help in determining the thermodynamic properties of the molybdenum sulphide which is in equilibrium with metallic molybdenum and sulphur vapor in the temperature range 1025" to 1150°C. From the results of MontoroL and of Parravano and Malquori' molybdenite would be expected to be in equilibrium with molybdenum metal, while the results of Guichard indicate that a lower sulphide must be in equilibrium with the metal. Thus it was concluded that the problem warranted reconsideration, especially in view of the suspiciously low temperature independent term for the standard free-energy function for the reaction MoS² Mo + S,. The reaction was calculated and duly noted as being low by Richardson and Jeffes,' using the data of Parravano and Malquori.' Experimental Method The general method used in this investigation is that of the Knudsen orifice method for the determination of equilibrium pressure. The apparatus and technique are similar to those described for the determination of the vapor pressure of silver.% owever, a closed-end McDanel tube instead of fused silica was used to maintain the vacuum, a molybdenum effusion cell with a replaceable lid was employed instead of a silica cell, and a titanium getter maintained at run temperature was used to assure that no oxidation of the molybdenum or molybdenum sulphide was taking place. All runs were made at a residual pressure less than 10-5 mm Hg. The data are given in Table I. Runs 1 through 13 were obtained using molybdenite, analyzed 98.5 pct, from the Molybdenum Corp. of America. The remaining runs were done with a sample from the Climax Molybdenum Corp. which was their grade No. 3 and analyzed 59.87 pct Mo. The weight loss of the cell during heating up and cooling down was subtracted from the total weight loss of the cell during the run. Also, when the tem- perature was changed, the Knudsen cell was placed in the vacuum chamber and heated at temperature for several hours in order to allow the sulphide and the metal to adjust their compositions to the equilibrium values, to desorb or adsorb gases into or from the molybdenum cell itself, and to desorb any water from the molybdenum sulphide or molybdenum powder inside the cell. Water may have been adsorbed inside the cell because, after each run, the top of the cell was removed and the material in the cell was stirred to insure that a layer of molybdenum metal would not build up and obstruct the passage of sulphur vapor into the gas phase. It was established that the molybdenum cell alone decreased in weight an inappreciable amount when heated at the highest run temperature for long periods of time. There are two questions to be answered before the data in Table I can be used to calculate thermodynamic functions: 1—Which molybdenum sulphide is in equilibrium with molybdenum metal and sulphur vapor? 2—What sulphur species are present in the vapor phase? It can be assumed safely that no molybdenum is vaporized, since its vapor pressure is almost negligible at these temperatures. It will be shown subsequently that no sulphide of molybdenum is volatile. Question 1 was answered in the following way: The especially purified molybdenite, obtained from the suppliers mentioned previously, was charged

Jan 1, 1956

By E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, Calif. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, N.Y., was developed by the Cabot Corp. A processing plant was placed on-stream in 1953, with nearly continuous production to date, and it is currently operated by Interpace Corp. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1973, the United States was the major producing country, furnishing about 75% of the world's output. Recent production also has come from Finland, Mexico, and Kenya. Small amounts have been shipped intermittently from India, USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and South-West Africa. The principal use of wollastonite is in the manufacture of ceramics, especially wall and floor tiles. Other uses are for paints, fillers, adhesives, reinforcing agents, plastics, fluxes, and glazes. Mineralogy Pure wollastonite, CaSiO3, has the composi¬tion of 48.3 % CaO and 51.7 % SiO,. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mobs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540° C. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both; colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The brightness of wollastonite is a property of considerable importance to the paint industry. Material, 99% pure, with a size of -325 mesh, has a General Electric reflectance rating of 92 to 96%. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature form. Inversion of wollastonite to pseudowollastonite occurs at about 1120° C, resulting in an increase in the coefficient of expansion and a color change. Pure white wollastonite, on inversion, may change to a cream tint, or various shades of red or brown. The color change is thought to be due to the presence of iron and strontium.

Jan 1, 1975

By Philip R. Strand

Vermiculite is the name used for those micaceous minerals with a ferromagnesian aluminum silicate composition and the unique property of exfoliating to a low density material when heated. Commercially, the exfoliated products are also called vermiculite, or more exactly, expanded vermiculite. In its exfoliated state, vermiculite serves many markets, chief among them construction, agriculture, horticulture, and general industry. Composition and Properties Vermiculite, in a natural state, has the characteristic mica habit, splits readily into thin laminae, flexible but inelastic. In a mineralogical sense, vermiculite is a hydrated silicate with no exact chemical composition. The structural formula for a macroscopic, trioctahedral vermiculite may be written: [ ] The structure of vermiculite is basically that of a talc, and it could be regarded as a trioctahedral member of the smectite group. Macroscopically, vermiculite displays the prominent monoclinic crystal faces that are commonly marked by lines at 60° and 120°. Hardness varies from 1.5 to 2.8 or more; specific gravities are between 2.1 and 2.8; color is amber, bronze, brown, dark green, or black. When heated quickly to an elevated tempera¬ture, vermiculite expands by exfoliating at right angles to the cleavage, into wormlike pieces (the name vermiculite is derived from the Latin `vermiculare,' to breed worms). This characteristic of expansion, the basis for commercial use of the mineral, is the result of the mechanical separation of the layers by the rapid conversion of contained water to steam. The increase in bulk volume of commercial grades is 8 to 12 times, but individual flakes may expand as much as 30 times. All expansion occurs at right angles to the basal cleavage. Vermiculite may also be expanded by a number of chemical processes such as soaking in hydrogen peroxide, weak acids, and other electrolytes. There is a color change during expansion that is dependent upon the composition of the vermiculite and furnace atmospheres. Heating in an oxidizing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. The exfoliation of the vermiculite crystal results in large pores being formed between groups of platelets. Thus exfoliation can make available a large increase in void volume without significantly changing the surface area of the platelets. This characteristic is important in the chemical carrier applications of vermiculite. Although there has been much research on the chemical and structural composition of vermiculite, an exact formula and composition cannot be described. This is to be expected since vermiculite derives from a number of different mineral sources. As has been proposed, vermiculite is not a single mineral species, but families of related minerals. Additionally, commercial interest in the end product has resulted in the name vermiculite being applied to the very voluminous, bloated products from calcination of baueritized (bleached) phlogopite. This has also resulted in many names for the specific vermiculite found in a particular deposit. All of this difficulty arises from the nature of its crystal chemistry. Consequently, vermiculite is now thought of as several related variable mineral series rather than a group of related species. The vermiculites have a common silica tetrahedral sheet structure with separating ions. It is now generally agreed that vermiculites must also be regarded as true clay minerals. The properties of the mineral, such as cation exchange capacity, organic complexing ability, and vari-

Jan 1, 1975