Search Documents

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By M. G. F. Söhnlein

In a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. + 20 8.0 40 36.5 + 60 9.0 + 80 10.5 + loo 5.5 4-150 1 4.5 -150 25.0 99.0 Loss 1.0 In the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.' This remodeled classifier consists of a truncated pyramidal wooden hopper A with an attachment of cast iron

Jan 1, 1917

By Charles A. Colton

(Read at the Amenia Meeting, October, 1877.) THE results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company's furnace, Port Henry, New York, are given in Tables I and II. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a a inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston,* to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solution as he states in his description of the apparatus, as many as 50, and sometimes 60, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to cause any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge. * See Transactions, II, 226; V, 487, 621.

Jan 1, 1878

By B. Egeberg

BRITANNIA metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two, other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375° F., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later.

Jan 1, 1928

By N. S. Kenny, A. A. Burr

THE purpose of this note is to present evidence that vacancies, which have been produced by quenching from a high temperature, alter the rate of strain-hardening of an hep single crystal. The majority of investigations of the effects of quenched-in vacancies on the yield stress of metals have been made using fee samples in the form of thin wires. However, there is an inherent disadvantage in using such wires to study the effects of vacancies on the rate of strain-hardening of metals because fee wires begin stage II slip either immediately upon yielding or very shortly thereafter. When stage II slip occurs, very rapid strain hardening also occurs, masking the effects of vacancies on the rate of hardening. In this investigation single crystals of magnesium hep were studied since magnesium has only one slip plane at low temperatures and has, therefore, an extensive easy glide region. In addition, the effect of both static and dynamic recovery on the rate of hardening were eliminated by testing in liquid nitrogen. Both forms of recovery occur in hep metals by dislocation climb, which is a diffusion controlled mechanism and is negligible at liquid nitrogen temperatures. Finally, the dependence of the strain-hardening rate on the crystal orientation was eliminated by using the equations of Schmid and Boas.' Variations in the strain-hardening rate could, therefore, be attributed to the presence of vacancies. Single crystals in the form of rods approximately 5 mm in diam and 6 cm long were grown by a modified Bridgman technique from commercial high-purity magnesium (99.97 pet) supplied by the Dow Chemical

Jan 1, 1962

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when . the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY- THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more.. Having found, that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1) ?-in 1925 about 220,000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 2, 1927

By H. S. Gieser

THE flotation of oxidized silver, ores offers an interesting problem to the operating metallurgist, who has to treat this material. The advances made in the art of selective flotation by the use of newer collectors with accelerating and inhibiting reagents suggests that there should be something to help to decrease tailing losses. For many years there was no working hypothesis, so the subject was approached more or less in the dark, but with the publication of a paper by Taggart, Taylor and Ince1 giving results of flotation tests with many organic compounds and presenting a tentative theory, a better foundation has been laid and henceforth progress should be more rapid. Over a period of one and one-half years there was much experimentation with flotation of oxidized silver ores at El Tigre, Sonora, Mexico. The material coming to the mill was straight sulfide ore in a silicified rhyolite gangue, the ore minerals being sphalerite, galena, pyrite and tetrahedrite. This came largely from the lower levels of the mine. With the approaching exhaustion of these orebodies, attention was turned to oxidized ores left behind during higher prices of silver. Of late oxidized ore has been at times 25 per cent. of mill tonnage. Aerofloat 25, in considerable quantity, together with ethyl xanthate, has been used in the mill. The former raises large quantities of "insoluble" or gangue, which is difficult to reject when the density of the tailing pulp approaches 33 per cent. solids, as it did during periods of water scarcity. The mill tailing at times contained as much as 5 oz. of silver on a 32-oz. mill head.

Jan 1, 1931

By Walter Lee Brown

One of the characteristic steps in the march of modern scientific progress is the substitution of improved time-saving and labor-saving appliances for the antiquated and, in most cases, inconvenient forms of chemical and physical apparatus used by the earlier experimenters. This fact is strongly impressed upon us when we consider the question of the employment of illuminating-gas as a source of light, heat and power. Concerning its value as a light-producer, let the record of the past three-quarters of a century speak for itself. As a factor for power, we have evidence of its efficiency in the shape of the gas-engine. But its adaptability as a medium of heat, is the feature to which I wish to call attention, and in a special direction, viz., the assaying of ores. Gas assay-furnaces have been known and used for some years, but not to any very great extent, in this country at least. Therefore no apology on my part is required for the description I now give of a complete gas assaying-plant. The illustration accompanying this paper is a faithful representation of the group, as it was designed by, and arranged for myself, and appears in actual running order in my laboratory to-day. Its duty is to do roasting, crucible-fusion, scorification and cupellation. The furnace at the left is for roasting sulphurets or other ores for experimentation or actual work. It is what is known as a Fletcher No. 163, and consists of a fire-clay body strapped with sheet-iron bands, and a burner (No. 16, Fletcher). The opening at the top

Jan 1, 1885

By E. C. Rien

When the electrical system for a surface or open pit mine is designed, four major considerations should be satisfied in the following order: safety, reliability, flexibility, and cost. Careful planning initially will make expansion for future growth economical as well as possible without extended shutdown of operations. Electrical requirements in surface and open pit mining can be divided into three categories: main substation, plant power, and pit distribution. These systems are integral to each other, but will be dealt with separately here. 11.2-1. Main Substation. A main substation for a mining operation may vary from a 500 kva transformer supplying 480-v power to motor-driven pumps and conveyors, to a 50,000 kva substation serving a large beneficiation plant or a large strip mining operation. Regardless of size, it should be designed with the realization that a failure of the main substation will totally shut down the operation (Fig. 11.2-1.). Location of a main substation usually is a compromise between expense of running the incoming high-voltage transmission lines and the voltage drop of long secondary runs. Based on a geological survey for immediate and future areas of excavation, the main substation should be located as near to the center of load as possible. The site should be out of the blasting area, readily accessible to authorized personnel, and situated where prevailing winds will keep it free from dust or snow. DISCONNECTS AND OVERLOAD PROTECTION. The main substation should have a primary disconnecting device-either a pole top gang-operated switch and fuses of adequate interrupting capacity or, preferably, an oil circuit breaker with properly coordinated relay protection.

Jan 1, 1968

By Henry Kreisinger

IN evaluating coals as steaming fuel on the basis of chemical and physical properties of the coals, the only properties that can be used are those for which the methods of determination are well established and standardized, and those that affect all methods of burning the coals in the same way. The discussion is written from the standpoint of the coal consumer. The production of steam is the largest field for the use of coal. It includes stations for generating electric power, central heating plants, industrial power plants where steam is used for power generation, factory processes and heating. The field also includes steam locomotives. Small house-heating boilers are not included in this field because such small boilers generally burn specially prepared domestic fuel. The plants using the steam coal are equipped to burn the coal when fired by one of the three general methods: namely, hand, stoker, and pulverized coal. The hand firing is now restricted to small plants and to locomotives. Central stations and larger industrial plants use either stoker or pulverized-coal firing. Some locomotives also use stokers. Pulverized-coal firing has been tried in locomotives but so far its adapta-tion to this use has been handicapped by practical difficulties. The coals used for steaming purposes are generally of the bituminous and semibituminous classes, with volatile matter ranging from 15 to 35 per cent. Coals belonging to these classes are produced in many parts of the United States and form by far the largest part of the total coal production of the country. The value of any coal as fuel for steaming purposes depends on the following factors

Jan 1, 1935

By Porter W. Shimer

Ox completing the filtration of a solution of pig-iron in hydrochloric acid, and after apparently everything had been transferred to the paper, a minute residue was observed remaining in the angle of the beaker in which the solution had been made. This residue had a steel-gray color and metallic luster and was hard and gritty when touched with a glass rod. Placed under a microscope and magnified 400 diameters, the substance was found to be made up almost entirely of opaque cubical crystals with some fragments having the same color and luster as the cubes. The appearance was strikingly like that of a collection of crystals of iron pyrites. The amount of material obtained from ten to twenty grams of borings by solution in dilute hydrochloric acid, and careful decantation from graphite, was barely sufficient for a microscopic slide. A qualitative test of the minute amount of material obtained in this way, showed the presence of considerable titanium. After many fruitless trials by decantation and other methods, sufficient material for quantitative analysis was finally obtained in the following manner: Two hundred and fifty grams of the coarsest possible borings were dissolved in seven liters of hydrochloric acid of sp. gr. 1.03. A solution by the aid of heat took four to five hours. It was allowed to settle, and the clear solution poured off. Great care was taken that none of the material which had settled to the bottom was lost. The graphitic residue was then completely transferred upon fine bolting-cloth, previously Stretched and fastened over the top of a beaker. All graphitic lumps were broken up by the finger while

Jan 1, 1887

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more. Having found that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1)?-in 1925 about 220;000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 1, 1927

By W. H. Forbes

As permissible explosives and electric detonators are now generally recognized as the only safe means of blasting in coal mines, this paper is limited to their use. Causes of Misfires There are many different causes of misfires, but the principal ones are as follows: 1. Explosives which have deteriorated through improper storage either at the storage magazine, the distributing magazine, or at the working face. This is not only true of the explosive itself, but also of its detonating agent. 2. Improper priming and charging at the working face. This commonly occurs when the explosives are handled by inexperienced persons. 3. Improper methods of tamping; the leg wires of the detonator may be abraded or broken by the tamping bar or stick, thereby causing a short or broken circuit. 4. Faulty leading wire, or electrical apparatus of insufficient strength to explode the detonator. Prevention of Misfires Storage is an important factor, especially with permissibles of a nitrate or ammonia base. Both explosives and detonators should be stored in substantially built, fire-resisting magazines and should be situated so that the minimum amount of moisture and heat is present. They should be so constructed that a constant supply of fresh air enters; the floor of the magazine should be raised to permit the circulation of air under the stored explosives. Boxes should be stored top side up and in such a manner that the old explosives are used before those of a later delivery. This eliminates chance of deterioration from lengthy storage. Detonators should be similarly handled and stored. The distributing magazine stock should be regulated so that not more than one day's supply is on hand.

Jan 1, 1930

By William A. Vogely

Mining employment in the United States declined from 986,000 employees in 1948 to about 600,000 employees today. This has occurred even though the Index of Physical Volume of Mineral Production (1957-59=100) has increased from 88 to 111 and the value of mineral production measured in constant(1957-59) dollars has increased from $14.7 billion to approximately $19.3 billion. Average unit mine value has increased 24% as compared with a 34% increase in prices in general. Apparent consumption has increased more than domestic production, indicating an increased dependence on imports. The mineral economy presents a complex pattern of development factors in the post-war period. This article presents a technique by which the various forces that have been acting on the market for a mineral commodity may be sorted out and by which the extent of the impact of technological change in use as well as the technological change in production can be measured. If one is interested in delineating fully and completely the impact of technological change upon the mining industries, it is not sufficient to describe the increase in productivity reflected by the above employment and production figures. What is reflected there is only the effect of technological change in the production function of the commodities under concern. These effects are obviously very substantial and have major implications for labor, capital and supplying industries. However, they are not the only effects of technological change and, in fact, may be relatively minor when the impact which arises because of changing technology in the using or consuming industries is considered.

Jan 4, 1965

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

IN spite of considerable study,1-5 the nature of slime coatings in flotation is still not completely understood. However, phenomena that control flocculation and dispersion of colloidal systems are now interpreted in terms of electrical double layers."' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed, flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which electrokinetic data are available.8-12 Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple.

Jan 7, 1958

By Richard P. Rothwell

The device to which I desire to call the attention of the members of the Institute consists of a water-tight caisson, which is connected By a stuffing-box with the tube to be laid, and the caisson is pushed forward with hydraulic jacks set against the end of the tube. The tube is of hard white iron, cast in chills in segments. These segments are carried from shore through the tube itself, in which a track is laid as the work progresses, and the segments are bolted together in the caisson, where there is ample room to work and proper appliances for handling heavy weights. As each segment is bolted on, the jacks are set against its forward end, and when the whole ring is complete, the caisson is pushed forward by the jacks, a trench having been dredged out in front of it, or, in very loose ground, jets of water under a heavy pressure can be thrown out to loosen the ground in front of the caisson. The direction in which the caisson is pushed is completely under control, and both the caisson and the tube are loaded to the amount necessary to overcome their buoyancy. I understand that Mr. H. H. Hall, of New York, the inventor, is negotiating for the construction of a 16-foot tunnel of this kind across the Straits of' Northumberland, between Prince Edward Island and the main-land, and for tunnels in several other places. 4 One of the most interesting uses of this system is in laying water mains out into lakes. The work can be carried on without inter-

Jan 1, 1886

By Adolf Gurlt

It has long been known that minute quantities of foreign substances, when alloyed with steel, are capable of materially altering its physical properties. Thus, half a century ago, Faraday and Stodart, in England, discovered in the famous Indian steel, known as " wootz," small quantities of aluminum, from 0.0728 to 0.693 per cent., and attributed its extraordinarily good quality to the presence of such minute quantities of that metal. Since aluminum is now produced by electrolytic means on a large scale and at low cost, its addition to cast-steel has been frequently recommended of late. Chromium was alloyed with steel fifty years ago by the celebrated French metallurgist, Berthier, of Paris, and has recently been successfully applied to the same purpose by Holtzer, of Terre-Noire. In 1860 titanium was alloyed with crucible steel by Robert Mushet, of Coleford, the alloy containing up to 0.50 per cent. of titanium, which was extracted from Norwegian ilmenite. The titanium-steel was much vaunted by him for its excellent qualities. Rhodium, a very rare metal of the platinum series, was maintained by Berthier to improve steel materially in strength and hardness. Manganese has always been held by Sheffield steel-melters to provide steel with excellent qualities, and this influence was quite recently investigated by H. M. Howe and L. Campredon. Nickel was tried as an addition by Berthier, not to speak of gold, silver and platinum ; and nickel-steel has recently been brought into prominence by J. Riley and others, who recommend it for its great strength and toughness, particularly as material for armor-plates.

Jan 1, 1894

By M. G. F. Sohnlein

IN a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. +20 8.0 +40 36.5 +60 9.0 +80 10.5 +100 5.5 +150 4.51 -150 25.0 99.0 Loss 1.0 IN the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.1 This remodeled classifier consists of a truncated pyramidal wooden hooper A with an attachment of cast iron

Jan 4, 1916

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

By M. F. Fogler

An attempt to duplicate Rawdon and Mutchler's experiments showing a reversal of hardness with continued rolling gave negative results, indicating that the phenomenon is not general but depends, probably, on local conditions of rolling. IN A recent paper, Rawdon and Mutchler1 gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between-the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925