Search Documents

By W. Rostoker, H. Nichols

The embrittlement by mercury of aluminum alloys in various states of anneal, cold work, and aging has been studied. It is shown that single phase and non-precipitation hardened structures irrespective of de,pee of prior cold work demonstrate some small measure of yielding before fracture occurs. Sub-yield-stress failure is confined to the aged state, and embrittlement is accentuated by small plastic prestrains. With large plastic pyestrains, embrittle~nent is progressively reduced. In previous work' it was shown that the propensity of commercial aluminum alloys for embrittlement when wetted with mercury seems to be related primarily to the intrinsic strength in the normal un-wetted condition. The data from a large number of commercial alloys in various states of anneal, cold work, and/or aging gave a generalized relationship. At low strength levels, the wetted fracture strength increases proportionately to the increase in tensile strength; but above 65,000 psi normal ultimate strength, the trend is abruptly reversed, and the wetted fracture stress decreases proportionately to the increase in tensile strength. This paper will demonstrate that the simple character of this relationship between normal tensile strength and wetted fracture strength is fortuitous. It will be shown that structure and thermal-mechanical history are clearly relevant factors. The term brittle fracture has been used to connote the geometry of the fracture surface (transverse vs shear plane) or the negligible extent of preceding plastic strain. At its maximum effectiveness, liquid metal embrittlement can satisfy both criteria—fracture transverse to the axis of tension and without observable plastic strain. In this paper, brittle fracture will signify failure at stresses below the engi-

Jan 1, 1962

By Charles B. Dudley

It is evident that, as the size and weight of cars have increased, the demands on the cast-iron car-wheel have become more and more severe. Fortunately, the factor of safety in the cast-iron wheel, as originally made, was so large that it was only when freight-cars approached the capacity of from 80,000 to 100,000 lb. that the question of wheels began to give some anxiety. A moment's thought will show that, as freight- and passenger-cars have increased in weight and size, a much greater duty is required of the same eight wheels than was formerly the case. In other words, although the cars have increased in capacity from 15 tons to 50 tons each, the number of wheels under a car has not been generally increased. It is true, some cars have been equipped with 12 wheels, but this construction is not the rule. Hence the duty which the wheel must perform has become much more severe, and although it was clearly able to stand some increase, there must evidently be a limit somewhere which cannot be exceeded. Meanwhile, it is the part of wisdom to make better wheels if possible, and accordingly, no little study is now being devoted to the requirements for cast-iron car-wheels; and modifications are being made, both by increasing the weight of the wheel and by improving the quality of the metal of which it is made. The desire to improve the quality of the wheel has led to the preparation of specifications for its manufacture; and within the last 15 years a more rigid scrutiny of the wheel is char-

Jan 1, 1905

By G. R. Speich

RECENT studies by Smith and Olney,1,2 Olney,3 Greifer and Salli,4 Rys etal., and Olney and smith 6 have established that graphite is the first decomposition product to format the surface of hypereutectoid plain-carbon steels when they are austenitized in a vacuum or inert atmosphere and slowly cooled. This graphite evidently forms directly from the austenite and only at the surface of the specimen. The interior of the specimen is found to be free of graphite. The graphite layer can almost completely cover the specimen surface and the rate of its formation is markedly sensitive to the orientation of the austenite. The present work was undertaken to study this phenomenon further, especially with regard to the effect of temperature and austenite orientation. The material studied in this work was a high-purity iron-carbon alloy containing 0.88 pct C, 0.005 pct Mn, 0.016 pct Si, 0.005 pct S, and 0.002 pct P. Specimens were heat-treated in a commercial hot stage modified for rapid quenching.7 This permitted direct observation of the formation of the surface graphite. A vacuum of 10"" to 10-5 mm of Hg prevented oxidation or decarburization of the specimens. Specimens were austenitized for 30 min at 1100°C and quenched to a series of lower temperatures where they were isothermally transformed. Surface graphite was observed to form at 700°, 750°, and 780°C but not at 825°, 900° or 1000°C. Since the maximum solubility of austenite for graphite is 0.88 pct C at 800°C,8 surface graphite only forms at tem-

Jan 1, 1962

By D. R. Mitchell

This paper discusses some of the fundamental physical and chemical characteristics of coal in Illinois that affect its preparation for the market. At the present time preparation consists almost entirely of sizing and hand-picking. The washing of coal has almost entirely disappeared from the state. This is a rather startling fact when one considers that in the year 1908 Illinois outranked all other states in the quantity of coal washed and a few years later, in 1912, 85 washing plants were reported. Two reasons are apparent for this change. One, which is probably the most important, is that immense areas of comparatively clean coal were opened; the other is that many of the early washing plants were inefficient, so that washed coal was looked upon with disfavor in many trade centers. Objectives of Operators Some of the outstanding preparation aims being given due consideration by operating men are: 1. The greatest possible production of lump and domestic sizes which bring in the market at least $1 per ton more than the fine sizes or screenings. 2. Efficient screen sizing with as little breakage as is consistent with economical operation. 3. The removal of extraneous ash and sulfur. 4. Utilization of low-priced screenings. 5. Suppression of dust in domestic coal shipments. Preparation Underground To get the greatest possible production of the larger sizes, preparation must start at the face. Improvements in blasting and loading have increased the sizes larger than 2 in. by as much as 20 per cent. at some mines. Tiffany and McKitterickl report the results of an investigation they made at a mine in southern Illinois in which, by a carefully controlled

Jan 1, 1931

By John Dresser

General THE controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec. The principal production is furnished by eight mines, seven of which occur within a distance of 6 miles, but there are also several smaller properties in the vicinity. The industry was begun in a small way some 35 years ago and has advanced more or less regularly ever since. The annual production now exceeds 100,000 tons and its value is about $3,000,000. It represents over 80 per cent. of the world's production. History Asbestos has been known in the eastern townships of Quebec since 1847, when attention was called to it in an official report by Sir William Logan, the first Director of the Geological Survey of Canada, but it was not until 30 years later that it came into commercial importance. The largest deposits, those of Thetford and Black Lake, were found in 1877 during the construction of the Quebec Central Railway. Work was begun upon them almost at once and has been continued ever since. The Danville mine, the next largest producer, was opened in 1879, and the slip-fiber deposits of East Broughton were located shortly afterward. For the first 15 years only the "crude" asbestos was recovered; that is, fiber long enough to be extracted by hand cobbing. Although this is still a valuable part of the production, it is now a relatively small part of the total output.

Jan 9, 1914

By E. R. Parker, C. F. Riisness

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By Luther W. Lennox

During the last few years, one of the great problems in the milling of all ores has been that of grinding. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of grinding to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of grinding methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative grinding resistances of a number of ores now being milled in this country and Alaska, the manage-mxitofthe Portland mills requested Samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh screen; in the screen analyses tabulated and plotted herewith, the 150-mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves. The experimental grinder was a small iron tube-mill, 8 by 121/2 in., in which was placed a definite number (74) and weight (3450 gm.) of 3/4-in. steel balls, 1 Ib. water and 1 Ib. ore. To obtain uniform conditions, each ore was first crushed and screened, and from the sized products a "standard feed" was artificially prepared, the same standard being adopted for all tests in that particular series. The prepared feed was

Jan 1, 1920

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done ? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on t,his subject, and the results seem to furniih an answer to the question propounded above. Sampling for the U. 8. Geological Survey Coal- Testing Plant. In organizing the work of the testing-plant, it was decided that coal, in car-load lots only, would be accepted for testing; also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sample from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory established in connection with the plant and operated under the direction of Prof. N W. Lord of the Ohio State University, Columbus, Ohio. Mine-Samp1ing.—Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations adopted for mine-sampling mas, that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine.

Jan 1, 1906

By G. R. Fitterer

BY means of the C-SiC thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. COMMERCIAL DEVELOPMENT OF THIS DEVICE Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, pro-cedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; never-theless, it is felt that satisfactory gains have been made inasmuch as each installation has indicated some effect of temperature upon the metal-lurgical operation, and has pointed the way toward technical and finan-cial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service. are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-SiC- thermocouple and the temperatures measured are discussed later in this paper.

Jan 1, 1936

By C. A. Queener, W. L. Mitchell

In recent years bismuth telluride has received considerable attention, primarily due to its value as a thermoelectric material. Since there seems to be little dependence of thermoelectric effect upon crystal orientation1 many of those who have previously worked with this material have been unconcerned with knowing its crystallographic angles to any degree of accuracy. However, when one studies deformation modes, lattice stresses, or the aniso-tropy of mechanical properties of a material, knowledge of the interplanar angles and their relationships as depicted in a stereographic projection becomes essential. Lange2 originally published crystallographic data which described the structure of bismuth telluride as rhombohedral with the space group A more recent work by Francombe3 presented data which corroborated and refined the original findings of Lange. In addition, Francombe established that there is no coexistence of rhombohedral and hexagonal lattices in bismuth telluride as was suggested by Vasenin and Konovalov,4 and that the structure can be treated as a pseu do hexagonal structure with an axial ratio, c/a, of 6.95 for convenience of presentation and study. The interplanar angles and standard projections for several unalloyed hexagonal metals have been previously published,5-9 but the present work appears to be unique in that it presents data for a rhombohedral compound in pseudohexagonal form. As a pseudohexagonal structure, this material has an extremely large axial ratio as compared to the usual range of approximately 1.5 to 1.9 for the hexagonal metals. Since the interplanar angles are a function only of c/a, the angular relations between various planes for Bi,Te3 will be grossly different

Jan 1, 1965

By C. F. Riisness, E. R. Parker

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By C. E. Beecher

IN the course of the experimental and development work of Henry L. Doherty in an endeavor to obtain an increased yield of oil from oil-bearing sands, it was Mr. Doherty's claim and contention that oil in an undisturbed pool was different in character and behavior than, the same oil when raised to the surface of the earth, and that the gas dissolved in the oil caused a marked reduction in its viscosity and surface tension. Prior to 1924 no information to support this contention could be found in the literature or by a discussion of the subject with technical men in Government and private laboratories. So far as could be ascertained no experimental work had been carried on to indicate that Mr. Doherty's claim was either right or wrong. All parties consulted agreed that the viscosity of the oil would be affected by gas dissolved therein to the extent that natural gasoline was present in the gas, but so far as could be determined any additional effect of the natural gas was unknown. Accordingly, it was necessary to devise equipment and carry on experiments which would either prove or disprove Mr. Doherty's contention or claim. Such apparatus was built under Mr. Doherty's direction and experiments were carried on to determine definitely the viscosity and the surface tension of the crude oils which contain dissolved gases under different pressures. The results of the experimental work carried on have proved that the claim and contention of Mr. Doherty were correct in every particular, as will be seen from the discussion of the subject and the data contained in this paper.

Jan 12, 1926

By M. Gensamer

THE PURPOSE OF THIS PAPER is to lay a foundation of elementary theory that might be useful in the discussions which it is hoped will be evoked during this Symposium. It is not my purpose to try to expound the details of the most complete theories as that would be impossible in the time at our disposal and, even if time were available, would probably be of less usefulness than a discussion of the principles underlying the advanced theoretical treatment. I shall try to discuss the fundamental bases for these advanced theories. There exists at the present time very much less need for a detailed description of complete theory than existed when this Symposium was being organized. The reason for this is that a series of papers by L. R. Underwood has been appearing in the magazine Sheet Metal Industries. It is understood that this series will he published soon in the form of a book. Dr. Underwood's articles are complete, critical and well written and it would be hopeless to try to do better in less space. The need, then, is for a brief treatment of basic theory. The objective of any theory of plastic forming- is to enable one to calculate the force and power requirements for the process, and where the deformation is not uniform, to calculate the distribution of strains- In the formed object. We need as the basis for the calculation the relationship between stress and strain in the metal, particularly for the combination of stresses imposed by the forming process. We need to know the stress-strain curve for some simple state of stress, and we need in addition some theory

Jan 1, 1948

By R. Lagneborg

WhEN mechanical twins initiate cracking it has been proposed1 that the friction stress for dislocation motion, in the Cottrell criterion for brittle fracture2 should be replaced by the stress required to propagate a twin, ttp. TF is the fracture stress, d the grain diameter, ß a geometric constant, u shear modulus, and y the effective surface energy. Since TTp is likely to vary with grain size, it cannot be substituted by a constant in Eq. [I]. If an expression for the energy change caused by a twin in a stressed material could be obtained, it is in principle possible to compute the critical size of the twin, i.e., the size at which the system can decrease its energy spontaneously, as a function of applied stress, thus giving the stress required to just barely propagate the twin, i.e., TTP. Consider a circular twin disc with a radius r and having a lenticular cross section, Fig. 1. Twin dislocations3 of strength b exist in the twin boundary parallel to the twin plane, one loop on each atomic plane. Assume that the total numbers of loops, n, can be replaced by one circular loop of a multiple dislocation, nb with a radius r. The energy change of the system, AW, due to such a twin in an applied stress field can then be calculated: The first term is the total twin surface energy, the second the elastic energy due to the twin dislocations, and the third the energy released by the twin in the applied stress field. yt is the twin boundary energy, r, the radius of the dislocation core, and T the applied

Jan 1, 1968

By Sanford S. Cole

LABORATORY TESTS Takakuwa and Takamori' have applied the principle of phase inversion, well known in the chemistry of colloids, as a means of evaluating the wettability of minerals and to classify some frothing agents. By determining the angle of contact across the liquid phase of an emulsion, it has been possible to readily determine the wettability of a mineral. When this angle is less than 90°, the emulsion is of the oil-water type, and if it is greater than 90a, then the emulsion is of the water-oil type. The authors replaced oil with benzene in their recommended operation. They studied this method with the influence of ethyl xanthene on galena, on activated or unactivated zinc blend and of sodium cyanide on chalcopyrite and zinc blend. Raffinot and Formanek" described a pilot flotation plant with a capacity of 33 to 66 lb per hr of ore which is at the Laboratory of the Sociktk Minerais et Metaux in Paris. The plant will handle about 440 lb of ore per 8-hr shift and a regular series of tests can be undertaken with two to three tons of ore. Ore is ground to 0.1 in. and blended in advance. The plant includes two mills used either as rod mills or ball mills, conditioners, four groups of three cells for rougher circuits, eight cleaner cells and two small mills for regrinding middlings. Automatic controls for the pulp level in the cells, automatic sampling and addition of flotation reagents by electric valves facilitate plant operation and help to produce regular runs in spite of small throughputs.

Jan 8, 1963

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By C. B. Sawyer

ALTHOUGH the element beryllium was discovered as the oxide by L. N. Vauquelin in 1797, this metallic element was not produced until about 1828, and then only as an impure powder. Thereafter the greatest single contributor to our early knowledge of beryllium was Lebeau who, in about 1899, made pure beryllium crystals by electrolysis of the fluoride and then beryllium copper by the arc-furnace reduction of beryllium oxide with carbon and copper. About twenty-five years later, under the impetus of the work done by Siemens-Halske, beryllium commenced to make relatively rapid gains in industrial importance, principally when alloyed with copper. At the present half century mark, its use is firmly established in beryllium copper and in X-ray disks of pure beryllium. Its use as a moderator in nuclear processes in piles is engaging experimental attention and might become important. Other minor uses, but increasing in interest, are in nickel-base or iron-base alloys as a strengthening agent; as a protective agent against oxidation in aluminum and magnesium-base alloys; and as a ceramic in the form of the pure fused oxide. A false start was made in the wide use of beryllium oxide as a fired fluorescent powder known as beryllium-zinc silicate, a component of the inside coating of fluorescent lamps. This application, wherein general use by the public attained some importance, was abandoned a few years ago. This action was a consequence of the uneasiness which had been generated during the past decade by the sometimes fatal health hazard to the pulmonary tract now generally attributed to beryllium and some of its compounds. Numerous law-

Jan 1, 1953

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metaliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land the surface of which is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years .ago, has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are equally applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral, owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1927

By David J. Selleck, Eugene P. Pfleider

9.61. Introduction. Open pit mining methods produce more than 80% of all raw materials today in the United States. Much of this comes either from properties that formerly employed underground methods and were converted to open pit or from mines that ultimately must go underground when the economic stripping limit is reached. Generally the ores are transported over large vertical distances and techniques have been developed to do this economically. One approach is to combine conventional surface trucking, over relatively level roads, with the use of gravity and underground facilities. There are various modifications, depending upon the character of the orebody and the topography. Several schemes, as used in Sweden, Canada, and the United States, merit describing. One of the critical problems involved in the transference of ores from surface to underground is that of flow of bulk solids. Must it be crushed? Will it hang up in the transfer? What size and inclination of ore pass are required. How is the ore best fed onto the transporting device underground? As an example, the planning engineers for the Carol Project of the Iron Ore Company of Canada faced these problems in making their designs for the production and transportation of some 55,000 tpd from their Smallwood Mine in Labrador. Other operations, facing somewhat similar conditions, used other approaches of interest. This chapter describes some of the factors involved in the design, construction, and operation of a combination surface underground transportation system as applied to open pit mining operations. 9.62. Tunnel-Ore Pass Systems. The type, shape, dip, and size of the orebody, as well as the surface topographic features, generally estab-

Jan 1, 1968

By L. C. Uren, J. Domerco

That the diameter of a well through the oil-producing formation has an important influence on its rate of production is a principle accepted by many petroleum technologists. Knowledge of this principle extends back at least to the time when Slichter and King1 confirmed it in a study of the dynamics of flow of water through porous strata into wells. More recently, the senior author2 and his associates3 have produced qualitative experimental data confirming the principle as applied to drainage of expanding oil and gas mixtures, and suggesting that wells of large diameter, or wells having cavities about them within the reservoir rock, enjoy a material advantage in competition with wells of ordinary diameter. Apparently, however, no one has produced experimental data designed to indicate quantitatively the advantages that wells of large diameter possess in comparison with wells of normal diameter producing under comparable conditions. This paper reviews some preliminary experimental results of this kind, together with some conclusions and speculations based thereon, which further emphasize the importance of well diameter as a factor in determining the efficiency of oil recovery. Theoretical Aspects of Radial Flow of Fluids into Wells It is well understood that in a reservoir rock of uniform thickness and permeability oil and gas flow toward the wells along radial lines. The cross-section of the reservoir rock through which the fluids must move becomes ever smaller as the wall of the well is approached. The velocity of flow must therefore correspondingly increase, an effect that is accentuated by the rapid increase in volume of the fluid due to release

Jan 1, 1935