Search Documents

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently recon-structed smelter at McGill. A number of years prior to this improve-ment, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelt-ing operation. Results were encouraging, and in November 1932 the roasting plant was shut clown. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting clown of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter.

Jan 1, 1938

By Franklin J. Stermole

INTRODUCTION Economic evaluation of an open pit mine is similar to the economic analysis of any major investment project in any industry. It requires (1) taking into account all of the costs and revenues that are estimated to be incurred over the economic life of the project; (2) crediting the project with all the tax savings and tax credits that will be realized over the project life from tax deductions and credits related to various project costs; (3) charging the project with all taxes to be paid on taxable income over the project life; and (4) properly accounting for the time value of money for all project costs, revenues, taxes, tax savings, and tax credits when making the overall project economic evaluation. These considerations must be taken into account for any valid method of economic analysis such as discounted cash flow rate of return (DCFROR) or net present value (NPV) analyses. All economic analyses fall into one of two categories. ( 1 ) comparison of income-producing alternatives, or (2) comparison of service-producing alternatives. The analysis of alternatives in either of these categories can be made by using correctly any of five basic economic evaluation approaches which are. ( 1 ) present value, annual value, (3) future value, (4) rate of return (ROR) , and (5 ) break-even analysis. Of these evaluation techniques, DCFROR and NPV analyses are used most widely for evaluating income-producing alternatives while present worth cost and equivalent annual cost analyses are used most often for the evaluation of service-producing alternatives. In this chapter income- producing alternative analysis is emphasized, so DCF- ROR and NPV are utilized for evaluating the case studies presented.

Jan 1, 1979

By Sidney A. Swensrud

The writer has been interested for some time in trying to appraise our industry's prospects for gasoline consumption over the next half dozen years or so. Anyone who has even approached the problem knows the intimate relationship to it of the number of automobiles in use— by automobiles I mean both passenger cars and trucks. Probably at least 90 per cent of our gasoline is used in automotive vehicles. Some recent estimates secured from the Department of Commerce show the following breakdown: Per Cent Passenger cars............................................ 60.0 Trucks................................................... 27.4 Busses................................................... 2.9 Taxicabs................................................. 2.2 Subtotal............................................... 92.5 Aviation, motor boats and railroads......................... 0.5 Agricultural: farm tractors, etc.............................. 3.3 Balance (manufacturing, government use, construction, etc.)... 3.7 100.0 Up to the beginning of the depression there was, of course, a constant annual increase in the number of automobiles in use, for each year the industry added to the total inventory or ''population" more new units than were being scrapped, as may be seen in Fig. 1. Few of us in the oil industry needed to give much attention to the detailed figures, although the automobile industry seemed to interest itself in all sorts of calculations of replacement demand vs. new car demand, the average life of the car, the number scrapped, and the like. Probably many people in the oil industry, as well as outside it, were surprised at the way in which automobile registrations and gasoline consumption held up during the early years of the depression. Nor were they greatly perturbed when, as in the last two years, both registrations and consumption began to fall somewhat. That was natural enough; it

Jan 1, 1933

The American mining industry is vigorous today because it is young. At a time when the ore deposits of central Europe, for example, were being exploited actively, those of the United States were lying practically untouched. The founding fathers of our republic were not interested in mineral wealth because they were ignorant in such matters; their preoccupations were with defence against the Indians, the clearing of the forest, and the starting of agriculture in their new domains. They had no idea of establishing a mining industry. The Indians whom the American colonists dispossessed had no mines; they used only the metal that was to be found lying on the surface of the ground. Their arrows and spears were tipped with flint, which likewise called for little digging, if any. The native copper that glacial action had torn from the lodes of the Lake Superior region and had carried into the valleys of the Ohio and Mississippi was employed in the making of earrings, bracelets, knives, and scrapers. The same useful metal was found in many other places, in Virginia and Carolina, in Vermont and New Jersey, for example, but the Indians did not know how to melt it, much less how to smelt the ore, therefore they shaped it into tools and implements by hammering. Fortunately for them the hammering of the metal caused it to harden and therefore to become serviceable for implemental use. It is doubtful if they obtained the copper by actual mining, that is, by digging or excavating; it is true we find traces of such operations in the Keweenaw .peninsula of Michigan, but we have no

Jan 1, 1932

By J. F. Myers

THE Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. TABLE 1.-Typical Analysis of Ore Treated Composition, Per Cent Mill Tons Capacity Cu Fe S Zn London 1,350 1.41 28.4 20.2 1.10 Isabella 850 0.69 44.7 31.6 0.31 LONDON MILL The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accom-plished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1940

By R. A. Anderson, O. D. Sherby, J. E. Dorn

Solid solution alloying increases the plastic properties of aluminum at elevated temperatures by solid solution strengthening, by restraining recovery and recrystallization, and by a Cottrell effect. When binary aluminum alloys are strained and aged at 1940° to 300°K they develop a yield point. This is attributed to a migration of dislocations to solute atoms during aging. IN view of the ever expanding interest in applications of metals and alloys to high temperature service conditions, it becomes increasingly important to be cognizant of the effect of various metallurgical factors on the strength of alloys at elevated temperatures. One problem of wide interest, not only because of its engineering significance but also due to its fundamental scientific importance, is the elucidation of the effect of alloying elements on the plastic properties of homogeneous a solid solutions at elevated temperatures. It is indeed astonishing to note that in spite of its importance, and in spite of extensive random testing of alloys at elevated temperatures, no systematic investigation has been reported yet on the effect of alloying additions on the plastic properties of a solid solutions at elevated temperatures. This deficiency in our knowledge prompted the investigation described in this report. Rather extensive data are currently available on the effect of alloying elements on the plastic properties of a solid solutions at atmospheric and sub-atmospheric temperatures. Such data might be ex- trapolated to higher temperatures and reasonable guesses might be made regarding the influence of such factors as recovery and recrystallization in order to hazard a qualitative estimate of the effect of alloying elements on the plastic properties of a solid solutions at elevated temperatures. Such

Jan 1, 1952

By Charles Jones

(San Francisco Meeting, September, 1915) IN any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific. Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in. the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly riot due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul.

Jan 9, 1915

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By Lytle Brown, Thomas C. Meadows

The rock now known to almost every Middle Tennessee farmer as " phosphate," was but recently recognized as such. The existence of a stratum of black siliceous rock in the hills surrounding the Nashville Basin has been known for many years to Dr. Safford, the State geologist. Nothing about it, however, would lead to the conclusion that it contains a considerable amount of bone phosphate of lime. The only feature that might attract attention is its very dark color; and since it occurs near the " black slate," one would naturally infer nothing more of interest to be connected with that feature than that this rock and the " black slate " derived their carbonaceous matter from a common source. Many of the country people have mistaken it for coal, or for an indication of coal; this impression being strengthened by the fact that, when a piece of the rock was thrown into a blacksmith's forge, a slight combustion was observed. As will be more fully explained, the phosphate-rock is of two kinds: (a) loose or separate boulders, occurring in a stratum of clay or blue shale; and (6) solid rock occurring in a continuous stratum. The boulders have been known for a long time as "balls," "kidneys," " stink-stones," etc. ; and as early as 1887, an analysis made under the direction of Dr. Safford, at Vanderbilt University, showed one of these boulders to contain 64 per cent. of bone-phosphate of lime. This information awakened no great interest in the matter, for the probable reason that at the same time it was known, or supposed to be known, that the boulder-beds were of limited extent as

Jan 1, 1895

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By James Douglas

No one mill attribute it to the partiality of friendship if I claim for Thomas Sterry Hunt the right to a place among that little band of men whom nature has endowed with what seems an almost magical power of insight into her mysteries. But those of us who knew him well, while me never ceased to wonder at the breadth of his genius, the fertility of his imagination, and the wonderful capacity of his memory, learned that these native powers would have availed little to win him his rank in science, had they not been stimulated by ceaseless mental activity, indomitable perseverance, and unflagging industry. Thomas Sterry Hunt was born in Norwich, Connecticut, on September 5, 1826. He came on his mother's side from that good old stock which gave to Puritan England the gentle mystic Peter Sterry and that uncompromising preacher Thomas Sterry, who wrote the notable tract, " The Rot among the Bishops " in 1667, and that gave to New England Consider and John Sterry, the mathematicians. While lie was a child the family moved to Poughkeepsie on the Hudson. There the father died when Thomas, the oldest son, was twelve. The mother and her family of six young children returned to the old home in Connecticut. For a short time Thomas attended the public school; but it was for a short time only, as he, thus early, was required to share the burden of the family support and to seek employment. This he found first in a printing-office, then with an apothecary, afterwards in a book-store. The surroundings may have been congenial, but the occupation probably was not; for he re-

Jan 1, 1893

TWO American students entered the École des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole curriculum and received, in 1860, the certificate given to foreign students in lieu of the official appointment and degree awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July. 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. One biographer says he went to Europe, early in 1856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans-

Jan 1, 1941

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases. Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By N. P. Pinto

Compacting below the recrystallization temperature was studied. Ideal density was attained at 550° to 600°C using 25 tsi. Compacts have strength and hardness higher than cold worked beryllium. The recrystallization temperature of this highly stressed metal is that of cast, cold worked beryllium and appears independent of pressing temperature. THE process metallurgy of beryllium is beset by many difficulties that hinder the production of sound beryllium shapes of controlled properties. Most of these obstacles are traceable directly to the low density, low ductility, and high affinity for oxygen of the metal. Castings are susceptible to cracking and porosity, and controlled grain size is not easily attained, yet is critical to further working. Any process must carefully avoid oxygen pickup. Conventional metallurgical processes, including melting, casting, forging, rolling, and extruding have been treated previously,'" as have the conventional powder metallurgical methods.' More recently, a method has been advanced for producing powder compacts of high density by hot pressing at 1000" to 1100°C, using pressures of 0.25 to 0.5 tons per sq in. (tsi).3 Here, Seybolt and coworkers attained theoretical density of 1.85 grams per cc using pres-sure-temperature combinations of 500 psi-1100°C, 750 psi-1075"C, and higher. The warm pressing of beryllium is a practical method for producing bars of controlled properties and appears to have certain advantages, particularly when high strength and hardness are required. Other investigators have studied the hot pressing of various pure metals, such as copper,"-" gold," iron,10-11 and aluminum." Their results indicate that ideal densities may be attained by compacting at temperatures less than 50 pct of the absolute melt-

Jan 1, 1955

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

The introduction and development of the flotation process have proved to be of such momentous importance to the mining industry of the United States that they deserve to be considered historically.* The origin of the use of oily matter in separating minerals in ores is obscure, because its beginnings were unregarded. The story told by Herodotus concerning the recovery of gold from the mud of a lake by means of feathers daubed with pitch in the hands of apocryphal virgins is as pertinent to our inquiry as the yarn, two thousand years later, of a young school-teacher in Colorado that was washing oil-stained ore-sacks in her brother's assay-office when she noted the floating of pyrite on the water contaminated by the oil. In any event, the method patented by Carrie Everaon in 1885 was a complete failure, except as factitious evidence for trying to disprove the originality of subsequent inventions. An early and inadvertent use of the affinity of oil for metallic surfaces is suggested by the story of Jason and the Argonauts, who extracted gold from the gravel of the river Colchis by means of sheepskins. The woolly hide sewed, like the blankets used in our early stamp-mills, to arrest the gold, which was further detained by the oil on the fleece. Strabo, referring to a later period, says that in the country of the Soanes, who inhabit the valley of the Colchis, “the winter torrents are said to bring down even gold, which the barbarians collect in troughs pierced with holes, and lined with fleeces; and hence the fable of the Golden Fleece”.† William Pryce

Jan 1, 1932

By Edward H. Robie

NEVER before have the annual company reports in the mineral industry field exhibited the typo-graphical art so abundantly as does the current crop. Time was when most company reports made a drab appearance and dry reading, mostly confined to financial data and text that gave little information to the public or technical men. Now, the dollar statistics assume less importance. Considerable information is given on what is going on at the company's plants, new equipment being installed, new methods, properties under development, ore reserves and grades, and similar information of interest to professional men working in the field. We have one suggestion for further improvement: The names of the officers and directors of the company are always given, but only a few companies give the names of the principal operating officials. We think, in the case of a mine for example, that the name of the general manager, his assistant, the mine and mill superintendents, and any other top operating officials who have been largely responsible for the success of operations, are worthy of mention. The reports are now widely read and this recognition is due them. Conspicuous among the annual reports that we happen to have seen, in point of typographical attractiveness, are that of the Texas Co., celebrating its fiftieth anniversary with a gold-plated cover and gold printing inside; and that of Noranda Mines Ltd., with a red and black cover that would attract attention anywhere. Comment on economics, taxes, and labor give an excellent picture of what our industry is facing. Consider the following, from the report of the Union Oil Co. of California:

Jan 1, 1952

By J. Lyndon Rosenblad

The strength of a jointed-rock mass is not well-understood. It is believed, however, that the behavior of a rock mass is governed by both the intact rock properties and the properties of the discontinuities. Rock research in the past has been concentrated on the determination of intact rock properties. Several studies are presently underway which should provide more insight into the properties of the discontinuities. Few research programs, however, have been undertaken with the intent of studying the composite rock mass behavior where either the intact rock strength or the properties of the discontinuities may control failure. There are three approaches available for studying the behavior of a rock mass, namely, field studies, mathematical models (finite element), and geomechanical models. A geomechanical model has been developed in this study where the strength and failure modes of a model rock mass are studied as a function of intact block geometry, joint orientation, joint properties, and confining pressure. The objective of this study is to gain some insight into the parameters that govern the behavior of a rock mass, which parameters are most important, and when these parameters control. This chapter describes only one phase of the study, the development of equipment for use with the rock-blocks model. The models being tested are approximately 22 x 22 x 6-in. The size varies slightly depending upon the joint orientation used. The equipment developed includes model material molds, reaction frames, loading apparatus, measuring and recording instrumentation, and other accessory equipment pertinent to the operation of a successful study. The usual problems in equipment development, such as uniformity of load application, loading capabilities, and reaction capacities are all

Jan 1, 1970