Search Documents

By James Norman, E. W. Gieseke

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content. it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, [t] the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2, 3 The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. STUDY OF METHOD OF FLOTATION SEPARATION Most of the work on concentration of spodumene was done with rock from near King's Mountain, North Carolina. Rock from two

Jan 1, 1940

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939

By F. P. Dewey

(Read at Amenia Meeting, October, 1877.) AT the Wilkes-Barre Meeting of the Institute, Dr. J. Lawrence Smith, in the course of his remarks on some peculiarities in the composition of irons, alluded to the so-called " buckshot" iron, and exhibited a specimen of this material. He said that when the small granules, or shot, were separated from the mass, they could be flattened under the hammer, and inferred that these particles had been decarburized by the blast before sinking into the hearth of the furnace, and thus we had the exceptional production of wrought iron in the blast furnace. I have recently obtained a characteristic specimen of this variety of iron from one of the furnaces at Orbisona, Pa. Considerable uncertainty existed as to its true nature and the conditions of its production. Its weight seemed to preclude the idea that it contained much or any slag, yet its lack of strength indicated that it was not homogeneous cast iron. At times considerable quantities had been produced, which could only be utilized by charging in the furnace and remelting. The specimen, on the freshly fractured surface, appeared to consist of flattened globules of iron cemented together by a bluish material which one would naturally suppose to be slag, and qualitative examination for lime strengthened this supposition. It was quite difficult to obtain drillings, as there was a tendency to split in several directions as soon as pressure was applied ; but enough was obtained to undertake quantitative determinations. They were found to consist of two portions-one attracted by the magnet, and the other not. By repeated separation the magnetic portion was found to be 94.44 per cent., and the non-magnetic 5.56 per cent. Analyses of these gave the following results :

Jan 1, 1878

AS you have seen, I have hitherto demonstrated to you the methods for bringing to their proper and pure bodies all metals of any kind of ore that you have found and mined. If these did not now serve human needs all these operations with so much expense and labor would have been profitless and in vain. Therefore I recognize that it is necessary in speaking to touch upon all their operations and to teach you to ma& use of the metals according to the works needed. There are, for instance, some metals that would serve poorly for certain works when reduced to their fineness and perfection. Also, many artificers, in order to avoid expense, are content with having a larger quantity of metals and do not care so much about their perfection. For this reason they willingly accept mixtures of one metal with another, for example, of silver or copper with gold, of copper with silver, and likewise of tin or lead with copper. Tin is accompanied by lead to avoid spoiling its nature completely. All this, however, is done with a definite proportion by weight and not by chance. These admixtures, as I have told you in another place, are called in gold, carats, and in silver, leghe. This, in fact, means nothing but the association of one metal with another, indeed, a soiling of their purity and fineness, to which they have been brought with so much hard effort and labor. But now leaving this discussion, I shall tell you in the present book as briefly as I can, in order, first of the alloying of gold with silver or copper, and then of that of silver with copper.

Jan 1, 1942

A GREAT labor, surely, is that of the coppersmith, since his every work must be hewn from the mass of copper by force of the hammer. At the beginning, middle, and, end all his works are inconvenient pieces and unpleasant to handle. If the work is done on the forge with the fire, it is done in order to refine or compose it into masses again, for drawing these out while hot with the blows of some heavy hammer, or in order to put the works in a condition that allows them to be drawn out while cold and worked. In this he puts all his labor and industry. He who works at this art often makes use of large hammers, sometimes of small ones, and sometimes of those that have a long iron head and a short handle. With these he is obliged ever to proceed in one of these activities, either extending the work lengthwise, narrowing it, or widening it. This is achieved by the manner and direction of striking and therefore it is sometimes hammered on the inside, sometimes on the outside, sometimes with the peen, and sometimes with the flat head. For instance, when he wishes to close it up he strikes it on the outside with the peen, and if he wishes to widen it he strikes it on the inside with either the flat head or the peen. In this way he proceeds to shape it with constant patience, and to make all the vessels that he works graceful. This metal, as I have told you, is soft, flexible, and tenacious under the hammer. It yields with a certain toughness, provided, however, that it is fine and without admixture of a trace of tin or other metal. That craftsman is a good master of this art who best makes every desired work

Jan 1, 1942

Dr. Wadsworth's discussion of leaching is straightforward and certainly points out some of the critical areas in regards to the fundamental aspects of leaching. I will address myself to the more practical aspects of leaching. As a couple of general comments, very fine particles are often dealt with only when necessary. In many processing applications the sands and slimes are separated with the sand portion being treated by common metallurgical techniques and the slime portion being treated essentially by any technology that will recover some of the values. Ore treatment techniques such as leach/precipitate/float (LPF) have been used in the copper industry to take advantage of leachable copper preferentially reporting to the fine fraction. The second advantage, of course, is the improved metallurgy associated with the treatment of the sand fraction. Cases can be made for sand/slime separations in the aluminum and uranium industry where most of the value reports to the slime fraction and the sand fraction is rejected In the agitated leach systems, fine particles are often the most readily attacked and leached. In dump, vat and in-situ leaching, fine particles cause considerable problems. The fines will tend to restrict the solution flow from portions of the leach feed. This either causes a significantly reduced solution flow or, more probably, the solution will channel, by-passing much of the ore. In either case the result is a decreased metal recovery from ore. The fine particles of principal concern are clays of a flat plate-like shape which can very effectively compact, swell and cause a decreased solution flow. Discrete silica grains or sulfide grains due to their shape, even though they may be very fine, will not cause nearly the problems clays and secondary precipitates can cause.

Jan 1, 1979

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949

By S. W. Parr

THE low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700° or 800° C. For convenience in this discussion, the single number 750° will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750°, there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750°, there is substantially no secondary decomposition; above 750°, the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750°. Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition, of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement

Jan 2, 1920

The housing of labor and sanitation at mines in India are difficult problems to solve because-no more than two or three castes will accept the same conditions, and conditions suitable to one coal-field are not applicable to other fields. It is also necessary to consider the financial standing of the different companies. The European companies, which pay 30 per cent. and more dividends, can erect more suitable houses than the Indian companies, which are just able to keep their heads above water. The Santhal will not live in a bucca-roofed house as a permanent dwelling, and both the Santhal and Koras have an aversion to living in a line of attached huts. They have forsaken a whole, line of houses in one of which a case of sickness or death has occurred, and those houses were afterward considered unfit by all other classes of natives. The Santhals, Koras, and Douri castes will not take drinking water from a stand pipe; wells must be furnished. When well water is not available, these people will take water from the nearest pool or tank regardless of whether or not the water is stagnant. The well tops should not he completely enclosed, nor should there be a drain around the top. The ground should slope away from the well. In the Girieih coal fields, the miners have a great objection to pucca floors; they prefer earth which is lapped, easily cleaned, and renewed. As it is customary for the miner to build his own house, the company supplying the roofing material, he takes a special interest in it, keeps it in order, and hesitates to leave it. Each house is surrounded by its own bit of land, which the inmate cultivates.

Jan 12, 1918

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, 1911, the fire area, in the Lowell mine continually increased. and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2 Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness .and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By John A. M. E. Church

AT the last meeting of the Institute, a discussion arose upon the question, " Is them pressure in coke ovens ?" and many of the members seemed to think that the superiority of the Belgian furnace might be due to the fact that it is a completely closed chamber, in which the gases given off by the coal are, or may be, at more than the atmospheric pressure. It seems to me that this position is untenable, and that an examination of one of these ovens in operation will show, not only that there is no excess of pressure in the coke chamber, but that the contrary is true, and a partial vacuum exists. The Belgian or François oven consists of a rectangular chamber closed at the ends by sliding doors, and furnished with flues in the side walls and floor. The new charge is introduced at a time when the furnace is so hot as to cause immediate and copious discharge of the volatile constituents of the coal. The gases pass downwards through the side flues giving out their heat to the walls and thus to the coal. Underneath the floor air is introduced and the gases burn, producing intense heat. Heat is also reflected from the arched roof upon the coal which is therefore heated from all sides. The especial advantage which this construction was designed to secure is that no air is admitted to the coke-chamber. All the heat is produced by the combustion of the uncokeable gases, and the yield ought to be a maximum. It is so in fact, allowing for the imperfections inseparable from furnace construction and management. Sometimes the yield is in excess of the percentage indicated by assay, showing that

Jan 1, 1873

W. A. SCHLESINGER,* Denver, Colo.-Two problems are of great interest to the radium manufacturer at the present tine: The first is to perfect a process, more efficient and more economical, which is capable of treating a greater variety of ores. . Practically all the radium now manufactured in the United States is extracted from carnotite ores and these vary a great deal according to their location. The amount of sulfates contained in the ore is of particular importance, and any straight acid-leaching method, such as developed by the Bureau of Mines, becomes prohibitive when the ore contains more than 0.5 per cent. of sulfates, as the sulfates go into solution and naturally precipitate the radium as insoluble radium sulfate. Since the amount of ore obtained from any one claim is usually comparatively small, it is necessary to work a number of claims in different localities, and a process, in order to be commercially satisfactory, should handle all of these ores. In other words, it would be entirely unprofitable for radium manufacturers to employ any process which cannot treat any but sulfate-free ores. He must deal with carnotite containing appreciable amounts of sulfates, and must be able to work this in with the other ores. Carbonaceous ores from certain sections in Utah; which are known to contain as pinch as 1.0 per cent. and more of volatile matters, are prone to a, nitric acid-leaching process. The second problem relates to the treatment of concentrates. There is no doubt that a very large amount of low-grade ore, containing less than 0.75 per cent. uranium oxide, is available. It has been demonstrated that these ores can be concentrated, but there is still room for research

Jan 11, 1918

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a 'binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs ; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

Jan 1, 1873

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The authors give a definition of the various types of corrosion that may affect a metallic conductor buried in the ground, namely: 1. The metallic conductor may be attacked by the surrounding soil. This phenomenon is purely local and is called by them soil corrosiveness. 2. The metallic conductor may connect two regions of the ground when the electrolytes have a different composition. An electrical current will then be generated and certain zones of the conductor will be oxidized. This is autogalvanic corrosion. 3. Stray current may flow in the ground and enter the conductor in certain sections and leave it in others, thus causing oxidization in certain zones; this is electrolytic corrosion. The soil corrosiveness has been studied extensively by the United States Bureau of Standards and the authors give a summary of the work carried out and results obtained along this line. In autogalvanic corrosion it has been shown, by the investigation of buried pipes, that the zones of corrosion are associated with the zones of egress of the electric current (anodic zones). The location of these zones can be determined by measuring at the surface of the ground the difference of potential that exists along the path of the pipe. This work is performed easily and quickly with the apparatus invented by the authors for the exploration of conductive orebodies. The problem of electrolytic corrosion is a difficult one because it is a question of stray current which may vary in direction and intemsity at every instant. Therefore the components of the electrical field must be known at a given station and compared with the components of the clectrical field at another station, at the same moment. This is achieved by a rccording apparatus that will register the variations of the intensity of the electrlc current along two rectangular directions, during several minutes

Jan 1, 1934

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971

By H. J. Maguire

Those familiar with mill-practice understand the work required of an average bucket-elevator, but I wish to call special attention to the wear on the buckets. I have been studying in what manner the life and service of the bucket might be improved, and I feel that an adjustable lip, attachable to each bucket without the aid of rivets, will be of material advantage. For illustration, consider the feed-elevator of a typical mill in the Cæur d'Alene district. The ore is carried by water in a launder from the feed-rolls and dumped in the " boot" of the elevator, directly in front of the ascending bucket. Middlings from the return-rolls are similarly handled. Under this condition the bucket not only carries the ore, but also picks it up, and this latter requirement determines the life and service of the bucket. It might be said that it would be better practice to convey the feed to the elevator and dump it directly into the bucket, but at one mill at which this plan mas tried the results were disappointing and the rubber belt was badly worn. The wear of the bucket is confined to the lip and the corners which have to pick up the material. When the lip on a corner of a '7- by 12-in. malleable cast-iron bucket is worn down about 3 in., the bucket is of no further value as a carrier and has to be replaced. The worn bucket, containing about three-quarters by weight of the metal of the original bucket, has a scrap value of about 10 per cent. of that of a new bucket. To the cost of the bucket, however, should be added the time-

Jan 1, 1913

By William B. Heroy

During 1932 no important changes occurred in the position of Africa as a producer of petroleum. The progress of development and production in each of the areas of interest is described below. Egypt The producing fields of Egypt are Hurghada and Gemsa, located on the west short of the Red Sea, and Abu Durba in the Sinai Peninsula. Most of the production is obtained from the Hurghada field, chiefly from beds of Cretaceous age. To the end of 1930 the Hurghada field had produced 2,831,751 tons of petroleum. The Gemsa field, discovered in 1909, reached its peak of production in 1914, when 88,000 tons were produced. Of late years the production has greatly declined. Total production of the field to the end of 1930 is 182,870 tons. The total production of Abu Durba to the end of 1930 is 7069 tons. The production of Egypt for recent years is as follows: 1928, 269,324 tons; 1929, 271,520; 1930, 281,997 (1,996,000 bbl.); 1931, 288,260 (2,038,000 bbl.); 1932, 253,182 (approximately 1,790,000 bbl.). Mozambique The operations of Inyaminga Petroleum Ltd., which was engaged in drilling in the colony, have been suspended. Angola Drilling operations in this colony, conducted by Companhia de Petroleo de Angola under a concession from the Portuguese Government, were continued. A test well drilled at Cacoba, about 60 miles southeast of Luanda, to a depth of 5651 ft. was not a commercial producer. A second well was being drilled in the vicinity at the end of 1932. Morocco Until last year the search for petroleum in Morocco was in the hands of several private companies but during 1932 the National Office of Liquid Fuels of the French Government took an active interest in the develop-

Jan 1, 1933