Search Documents

By Erwin S. Sperry

Some time ago, the author had occasion to make an alloy of equal parts of nickel and aluminum, for the purpose of adding small amounts of nickel to pure aluminum. The nickel was melted in a plumbago crucible under a layer of borax ; and at a proper temperature the aluminum was added, and the whole mass was stirred with a plumbago stirrer. The alloy immediately became incandescent and boiled. It was then poured into iron moulds, in the form of ingots weighing about 10 pounds. The metal when poured was very fluid and free from the viscosity so often noticed in nickel and nickel-alloys. The color of the alloy is gray, not unlike that of wrought-iron, and the fracture is devoid of any crystalline appearance. It is quite brittle, and can be readily ground to a powder in a mortar. More metal was made than was needed; and what remained unused was placed in a covered wooden box and set away. In about three months, as it mas again necessary to use the alloy, the box was opened; and, much to my surprise, nothing but a dark gray powder was found in it. This condition of the alloy could not be accounted for. An attempt was made to melt the powder and pour it again into ingots, but with negative results. Analogy pointed to disintegration; and it was decided to make a fresh sample of the alloy, and watch the material from the beginning. In the second experiment the conditions were identical with those of the first, with the exception that fluor spar was substituted for the borax. This change was made because it was thought that perhaps the borax might have been

Jan 1, 1900

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939

ARTHUR PHILLIPS,* Bridgeport, Conn. (written discussion?).-It is to, be regretted that the very valuable paper by Messrs. Bassett and Davis did not appear in the early war period. The data presented would have been of inestimable service to inspectors, of cartridge brass who, admittedly, had little or no knowledge regarding the relation of grain size to temperature of anneal, and no real appreciation of, the significance of the Brinell hardness test. The paper is of considerable interest to, metallurgists also. WALTER R. HIBBARD, ? Bridgeport. Conn. (written discussion§).-The writer has carefully studied Messrs. Bassett and Davis's paper with considerable interest, inasmuch as our laboratory has tested cartridge brass by means of a Brinell machine. In March, 1917, at the suggestion of the Technical Department of the American Brass Co., we started a comparison of grain-size measurements and Brinell hardness of-cartridge brass with a gage of 0.1 in. or greater. This was continued until March, 1918, when we adopted the Brinell hardness test as standard for brass 0.1 in. gage or greater, and discontinued grain-size measurements upon this metal. The data collected during the test showed that the Brinell hardness indicated more accurately how the metal acted in actual working operations. It was also more reliable because two manipulators check themselves closer by the Brinell test than by the grain-size measurements. It also consumed less time in making the tests. Alfred V. de Forest, formerly assistant research engineer of our laboratories, has described the apparatus and some of the checking results in a paper read June, 1918, before the American Society for Testing Materials.1 The writer hopes that a more satisfactory. method for testing cartridge brass and gilding in gages thinner than 0.1 in. may be devised than the present method of grain-size measurements.

Jan 3, 1919

By E. C. Burke, W. R. Hibbard

G. B. Craig (University of Toronto, Toronto, O,nt., Canada)—The advent of pyramidal slip at room temperatures in a magnesium crystal (M2,) and the very low value reported for the critical shear stress are puzzling. Table I1 shows the calculated values (approximate) for sin x cos I in this specimen if all the (10l) planes are considered. If So is the shear stress resolved in the direction of glide, on the glide plane, and U, is the stress operative in yield point tests, then: S,, — 325 (0.169) 55gpersqmm (approximately) for 1101: S,, = 325 (0.465) = 151 gpersqmm (approximately) for (0001): S,, — 325 (0.101) - 32.8 gpersqmm (approximately) Thus, we see the pyramidal plane in which the minimum shearing component operated. Barrett"' stated: "Experiments have repeatedly shown that, when there are several crystallographically equivalent slip systems in a crystal, the one having the greatest resolved shear stress will become active. ..." It does not appear to me that the measurements given are conclusive proof that pyramidal slip operated. E. C. Burke and W. R. Hibbard, Jr. (authors' reply) —Although the low value for the critical resolved shear stress for pyramidal slip may be puzzling, there does not appear to be any basis for questioning the validity of the measurements. Under the influence of constraints, slip systems having decidedly lower shearing components may become operative, e.g., "cross-slip" or the "forced glide" in magnesium reported by Bakarian. Since we believe that pyramidal slip occurred in the specimen because basal slip was inhibited, it is not too surprising to find an operative plane with a lower shear stress. -7 C. S. Barrett: Structure of Metals U94jl p. 2J6. New York. McGraw-Hill Book Co.

Jan 1, 1953

By B. F. Fackenthal

For the past year we have had in use at the Durham furnace a set of hollow pig-patterns made of iron, which have given such satis factory results that I think a description of them would be of interest to the members of the Institute. Before the introduction of these iron patterns, we used the ordi nary wooden patterns, made in the usual way with straps of iron along the sides to protect the corners from wearing off. The size and shape of these wooden patterns are shown in Fig. 1. When the patterns were new, the pigs weighed about 130 pounds each, and were uniform in size, and the moulding was clean. But constant use soon wore the patterns away; and at the end of a few months, the pigs had become, in consequence, so much lighter that the moulding, daily, of several additional beds was necessary to accommodate the same quantity of iron. As the patterns wear away, the moulding becomes ragged and the pigs rough. Moreover, wooden patterns are often destroyed by fire. I have known an entire set to be destroyed by a break-out of iron. The iron pattern which I have designed is free from all the objections to the wooden pattern, being not only more durable, but, in the long run, far cheaper. The iron pattern having the same shape and size as the wooden one, is made of the best flange-iron, of No. 13 gauge. After the sheets have been cut to the proper size, three heats are required for the flanging. At the first heat, each piece is stamped in a cast-iron form, which gives the proper shape to the bottom part of the pat-

Jan 1, 1889

By Walter Miller

Developments in oil refining were so varied during 1938 that a refiner had to be alert or be left behind. The long-talked-of conversion of oil refining into a true chemical industry using petroleum as a raw material was hastened, particularly in the realm of motor-fuel manufacture, by the increased understanding and use of catalytic processes. The petroleum refiner's vocabulary has been extended to include alkylation, cyclization, aromatization, and isomerization. There are other devel: opments of a similar nature, but these are now considered commercially feasible under proper conditions. New Equipment Less expensive equipment and processes encouraged new construction and replacement. Estimates of money spent in the United States on building new plants and remodeling existing installations during 1938 place the sum at not less than $200,000,000, a noteworthy amount in a year marked by a business recession. The commercial application of small-scale catalytic polymerization of refinery gases made one of the latest advances available to the smaller operators, who usually are faced with unit installation and production costs higher than the large refinery enjoys. Competition was thereby fostered. Outstanding in this respect was the construction of two or more polymerization plants in small refineries at extremely low installation costs, with amortization measured in months instead of years. Houdry Processes Bursting like a bombshell late in the year was the disclosure of the extent of the development of the Houdry processes of catalytic cracking, viscosity breaking, gasoline treatment, desulphurization, and polymerization, said to be applicable to almost any raw petroleum stock and yielding gasoline of exceptionally high octane number. This process is claimed to be particularly adapted to once-through cracking of aliphatic hydrocarbons, and when combined with any of the conventional thermal

Jan 1, 1939

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943

By Niels Hansen

Dispersion-strengthened aluminum products consist of an aluminum matrix containing finely distributed ceramic or intermetallic particles. Examples of the two types of product are SAP, in which the dispersed phase is aluminum oxide, and materials made from atomized aluminum alloy powder, in which the dispersed phase can be FeA1, particles.' A fundamental difference between the two types of product is that the elongation of aluminum/aluminum oxide products decreases with increasing temperature, whereas the elongation of aluminum- FeA13 products, like that of aluminum alloys, increases with increasing temperature. As regards the structural stability, aluminum/aluminum oxide products are stable to temperatures above 600° C as aluminum oxide does not react with aluminum, whereas prolonged heating at above 400°C of aluminum-FeA1, products leads to coarsening of the intermetallic phase and loss of strength.' On the basis of these results it is supposed that a dispersion-strengthened product combining strength, ductility, and stability at elevated temperatures may be obtained if the dispersed phase reacts with the matrix in such a way that the reaction does not proceed at any significant rate at the application temperature. Different ceramic or intermetallic compounds may be selected as the dispersed phase, and, as alloying of the matrix phase may also influence the reaction, many possibilities exist for each metal. In the present study, aluminum products containing different oxides have been examined. For a reaction to take place between the dispersed oxide and the aluminum the free energy of formation of the oxide (MeO) must be greater than that of aluminum oxide; the difference should, however, not be too great in order to limit the reaction rate. Furthermore the aluminum alloy formed when aluminum reacts with the dispersed oxide should have a melting point near

Jan 1, 1969

By P. E. Demmler

PHOSPHORUS combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent. grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal, Industry' gives-the following: Superphosphate of calcium, 60 lb.; granulated copper, 301b.; finely powdered coal, 10 lb. Similar formulas are given by Brannt2 and others, and detail 'variations are covered by patents, such as those of L A Jeffs3 and H A Webster.4

Jan 8, 1920

By Arthur Knapp

OIL-WELL depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. DATA FOR LEASE STATUS-TIME OR DOLLARS-TIME CURVE TIME LEASE MONTHS STATUS Lease purchased for $3000 0 -$ 3,000 No expenses chargeable to lease for 3 mo 2 - 3,000 Well A is started; cost of drilling for month is $16,000 3 - 19,000 Well is completed at additional cost of $10,000 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (see Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.: difference between expenditures and receipts gives profit for month of $5,000 5 - 24,000 Investment is small, cost of operating well A is small, so profits are $15,000 6 - 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000.... 7 - 5,000 Lease operation now becomes normal and curve becomes smooth 8 - 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000

Jan 1, 1921

By H. W. Imholz

Considerable stimulation was given to the interest in the lower producing zones of the North Central Texas area when several wildcat wells developed production in these formations. The Iron Mountain and Humble-Olander well in sec. 196, B.B.B. and C. survey, Jones County, Texas, had a potential of 7500 bbl. (after a 3000-gal. acid treatment) from the Palo Pinto limestone encountered from 3238 to 3250 ft. This well heightened the prospects for oil in commercial quantities in the Canyon, Strawn, Bend and Ellenburger formations in the adjoining counties of Shackelford, Haskell, Throckmorton and others. The Hickok-Van Parmer well in sec. 477 S.P.R.R. Co. survey, Eastland County, Texas, was good for 1040 bbl., natural, from the Ellen-burger limestone, encountered from 4024 to 4033 feet. The Hal Hughes-Cook and Jordan (Poindexter) well in sec. 350, block 6, S.P.R.R. Co. survey, Callahan County, flowed 890 bbl. in 9 hr., after acid treatment, from the Ellenburger limestone, encountered from 4369 to 4388 feet. Both of the Ellenburger wells apparently are maintaining the pressure and volume of their original potential tests, and will no doubt open up considerable area in the adjoining counties for prospecting to the Ellen-burger limestone. Production increased in the district from 12,081,871 bbl. in 1936 to 15,384,500 bbl. The increase was due to developments in Jones and Jack Counties. Jack County production increased from 896,680 bbl. in 1936 to 3,117,063 in 1937, while Jones County increased from 1,596,743 bbl. in 1936 to 2,289,322 in 1937. The remaining counties of the district showed a slight decrease in the amount of oil produced.

Jan 1, 1938

By H. F. Miller

Fox some years the prejudice against basic open-hearth steel for casting has been gradually decreasing. Yet many consumers and engineers still cling to acid steel for castings, because of their alleged greater freedom from blow-holes and sponginess. Acid steel has been used for this purpose much longer than basic steel; and the melters in acid practice had it well in hand when basic steel was first tried. Then the necessity of learning a new set of laws for the production of satisfactory basic open-hearth steel for castings became evident. The first of these laws, in my opinion, has to do with the furnace construction. The heat should be melted down as speedily as possible so as to prevent excessive oxidation. I have described in another article ' some furnaces designed by me, and having as one of their features the promotion of quick melting. Size of the Furnace. The hearth of the furnace, however, is a decisive factor in the production of solid castings. The manufacturer should know the size of the heats he intends to make constantly, and should have his furnace built for that size of heat. The hearth should differ in dimensions from that of a furnace making ingotr steel. That is, the bath should be deeper and should have less surface-area. A shallow bath permits the slag to come out soon after the steel commences to flow, and thus prevents the additions from going into the steel, or from becoming uniformly distributed in case they have been put in hurriedly. Under this head comes the very poor practice of making small heats in hearths of a much larger capacity. If into a 25-or 30-ton furnace only 12 or 15 tons of metal is charged per heat, the proportion of heats that will be wild, or show signs

Jan 1, 1913

By Walter Miller

Developments in oil refining were so varied during 1938 that a refiner had to be alert or be left behind. The long-talked-of conversion of oil refining into a true chemical industry using petroleum as a raw material was hastened, particularly in the realm of motor-fuel manufacture, by the increased understanding and use of catalytic processes. The petroleum refiner's vocabulary has been extended to include alkylation, cyclization, aromatization, and isomerization. There are other devel: opments of a similar nature, but these are now considered commercially feasible under proper conditions. New Equipment Less expensive equipment and processes encouraged new construction and replacement. Estimates of money spent in the United States on building new plants and remodeling existing installations during 1938 place the sum at not less than $200,000,000, a noteworthy amount in a year marked by a business recession. The commercial application of small-scale catalytic polymerization of refinery gases made one of the latest advances available to the smaller operators, who usually are faced with unit installation and production costs higher than the large refinery enjoys. Competition was thereby fostered. Outstanding in this respect was the construction of two or more polymerization plants in small refineries at extremely low installation costs, with amortization measured in months instead of years. Houdry Processes Bursting like a bombshell late in the year was the disclosure of the extent of the development of the Houdry processes of catalytic cracking, viscosity breaking, gasoline treatment, desulphurization, and polymerization, said to be applicable to almost any raw petroleum stock and yielding gasoline of exceptionally high octane number. This process is claimed to be particularly adapted to once-through cracking of aliphatic hydrocarbons, and when combined with any of the conventional thermal

Jan 1, 1939

By Lyle D. Randen

With the environmental movement beginning in the late 1960's came a deluge of permit requirements for the mining industry. Coal mining has been one of, if not the most, severely impacted of the mineral industries as a result of the passage of the Federal Surface Mining Control and Reclamation Act of 1977. Numerous provisions of this Act and numerous regulations developed under authority of the Act are being challenged in differing levels of the judicial system across the United States. Such court cases have had varied success. Numerous other regulatory programs that are not quite as dramatic as the SMCRA have presented an unending regulatory problem for mining operators. My comments in this presentation relate primarily to the major Federal and State agencies and their legal responsibilities which we in the coal mining industry must address in order to receive authority to construct and operate surface coal mines in the State of Wyoming. A list of the Federal and State agencies one could deal with in an application is as follows: 1. Bureau of Land Management (BLM). BLM is responsible for deciding where and when to lease federally owned coal and for establishing terms and conditions for leases. BLM also has some control over surface reclamation on federal land, i.e. regrading to eliminate highwalls, covering of spoils, maximum extraction of coal to limit future disturbance, contemporaneous reclamation, etc. BLM is also responsible for designation of federal lands unsuitable for all or certain types of surface coal mining operations. 2. Geological Survey (USGS). USGS coal mining responsibilities apply only to Federal and Indian lands and concern compliance with production requirements including diligent development, minimum production levels, royalty payments and resource protection, and

Jan 1, 1983

By G. Campbell

The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff’s theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which

Jan 1, 1984

By James Barr

WHEN phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. To attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per cent. of available phosphate, which, however, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney forma-tion, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss.

Jan 2, 1916

At the meeting of the Board of Directors the following resolution was passed: "The members of the Board of Directors of the American Institute of Mining Engineers desire: to place on record their appreciation of the very great generosity of one of their colleagues and a member of the Board, George D. Barron, expressed in his gift of $5000 to relieve the financial stringency caused by the unusual expenditures of the Institute for war work and the remission of dues of those members on active service." By-Law VIII. was amended to make a slight change in District No. 5. The report of the Auditing Committee was accepted. Tellers were appointed to: count the ballots on officers and on the proposed amendment. The proposed budget for the year 1919 was presented. The following resolution re Secretary Emeritus Rossiter W. Raymond, which had been prepared, by request, by Dr. A. R. Ledoux was then unanimously adopted. "The Board of Directors of the American Institute of Mining Engineers would place upon its minutes its profound sense of loss and sorrow in the death of Rossiter Worthington Raymond, Ph. D., LL. D., Secretary Emeritus of the Institute. Both as one of its founders and as its Sec-retary for 27 years, his was the guiding spirit of the Institute for more than a generation. "During the greater part of this long period, it might almost have been said that the Institute was Dr. Raymond-and Dr. Raymond the Institute. When with the progress of growth and development, great changes were introduced, Dr. Raymond acquiesced in these in spite of some misgivings, such as those with which a father might contemplate the emergence of his child from the careful supervision of the home; but as Secretary Emeritus for the past eight years, lie was always ready with valuable advice and helpful suggestion.

Jan 3, 1919

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,' is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1933 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy;. E-Insti¬ tute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; J-Mineral Industry Education Division; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of CONTRIBUTIONS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. METAL MINING TECH- NICAL PUBLI- TITLE AUTHOR MEETING TRANS. CATION VOLUME No. AND PAGE* 499-A.47 Red Ore Mines of the Woodward T. C. DeSollar New York, Iron Company at Bessemer, Feb., 1933 Alabama (11) CONTRI¬ BUTION No. 1-A The Owyhee Tunnels (16) P. R. Hines New York, Feb., 1933 2-A Sinking and Equipment of the No. D. D. Homer New York, 2 Shaft at Minas de Mata- R. H. Cromwell Feb., 1933 hambre (25) 3-A Subsidence Resulting from the Charles W. Allen New York, Athens System of Mining at Feb., 1933 Negaunee, Michigan (8) 4-A Effect of Approximately Vertical P. B. Bucky New York, Cracks on the Behavior of Hori- Feb., 1933 zontally. Lying Roof Strata (16) 21-A Selection of a Mining System (11) R. K. Warner New York, Feb., 1933

Jan 1, 1933