Search Documents

By Richard S. McCaffery

A Research on iron blast-furnace slags has been in progress since 1922 in the metallurgical department of the University of Wisconsin, supplemented by observations, tests and critical examination of operating records at 10 furnaces. From the data thus collected information has been put into forms suitable for use by furnace operators and is given in this report and the three accompanying papers.' In the viscosity results reported, it is estimated that temperatures were measured within 5" C. and that the viscosity determination of the particular slag investigated is accurate within ± 4 per cent. In the viscosity diagrams in the various papers, the equal viscosity lines were drawn in such a manner that in all cases they are located correctly with respect to the actual experimental results, but when determining a viscosity for a particular composition from the diagrams, the viscosity may. be slightly less accurate than the experimentally determined viscosity for the same slag, for the reason that the iso-vis lines interpolated between the experimental results may be shifted slightly without violation of the experimental data. The viscosity diagrams represent our judgment of their position under the above conditions, and we believe the relative accuracy of viscosity data taken from the diagrams is more than sufficient for any use to which the data may be put. Hundreds of samples of slags synthetically produced in the laboratory and of actual furnace slags have been studied in various ways. The ranges of compositions of slags used for viscosity measurements are: silica 25 to 55 per cent.; alumina 0 to 35 per cent.; lime 25 to 55 per cent.; magnesia 0 to 20 per cent. These measurements were made at temperatures of 1250°, 1300°, 1350°, 1400°, 1450°, 1500°, 1550°, 1600" and 1650" Centigrade. Descriptions of apparatus, methods used and statements of the problems investigated have been published in the papers listed in the bibliography beginning on page 120.

Jan 1, 1932

By George Stanley Scott

Many requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulfur on the value of the coal for the particular use for which it is intended. Coke fob Blast-fuenace Use For purposes of illustration, we take the case of coal washed for coke to be used in the iron blast furnace. The method outlined can be made general in its application by substituting for the figures used here the actual operating figures for the particular case under consideration. In general, it costs the blast-furnace operation from 8 to 25 c. per ton of pig iron to slag out each 1 per cent. of ash introduced into the blast furnace by the coke. This figure depends on which one per cent. of ash is removed, and decreases with decrease in ash. When blast furnaces and coal mines are considered as a whole, the figure decreases to zero and then becomes negative, on account of low recovery of washed coal. Various figures1 have been given by different investigators. These figures necessarily differ, not only on account of the differences in operating costs but on account of the difference in the respective fuels as well. For the purpose of this paper, which, as explained, is to point out a method of attacking a certain problem, the figures used in the exposition of the method are of secondary importance. It is apparent that no universally applicable figures can be used, because there are none. Each plant has its own coal,2 its own operating cost, and its own conditions.

Jan 1, 1930

By Frederic H. Lahee

The purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexial fault zone, and to show how the apparently very irregular well logs in these fields may be use? for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30" east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity River at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fauil zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a downthrow on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults. Oil Fields Associated with Mexia Fault Zone When speaking of oil fields associated with the Mexia fault zone, we refer only to those now producing from the Woodbine sand. In this category belong the Mexia, Currie, Old Richland or Seay-Cranfill, Powell, and New Richland fields, named in the order of their discovery (see Fig. 1). Subsequent development may prove that the gas found in the Boyd Oil Co.'s Connor well, north of Kerens, is coming from another pool in the same fault zone.

Jan 1, 1925

By P. A. Boeck

The thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste. Advantages of Insulation It is not necessary in this practical and utilitarian age to enlarge upon the need of prevention of heat losses, but attention may advantageously be called to the other benefits derived simultaneously with the saving in fuel and the increase in thermal capacity of furnaces when properly insulated. In most industrial furnaces—which are here spoken of in the broadest sense, indicating general high-temperature equipment for any purpose and heated in any manner—the operations are generally carried on through a temperature range which has been found by practice to give the most ef-

Jan 1, 1916

By C. Y. Wang

China now leads the world in antimony production, having contributed during recent years something over 60 per cent. of the world's production. The history of the antimony industry of China dates back to 1897 when the Tai Shing Co. was formed, under contract with the Hunan Bureau of Mines, for the smelting of the ore to crude; and in 1908 the Wah Chang Mining & Smelting Co. was formed for the smelting and refining of the ore and crude to regulus. The writer was then asked to take charge of the erection and control of this first plant for regulus production in China and has, since then, been more or less connected with the antimony industry in this country. This paper contains the results of many years' experience in connection with the Wah Chang Mining & Smelting Co., Changsha; the Pao Tai Mining & Smelting Co., Wuchow; the Loong Kee Smelting Works and the To-Cheng Smelting Works, Hankow; as well as information gathered from various other small smelters, scattered in different parts of the Provinces of Hunan, Hupeh, Kwangsi, and Kwangtung. An idea of the growing importance of regulus production in this country can be gleaned from the fact that, within a period of about 8 years, the export of regulus from Hunan alone jumped from 3 tons in 1908 to about 6000 tons in 1915; that a production of about 23,000 tons of regulus per year could easily be effected from all the smelters, as tabulated below, most of which were erected a year or two ago under the stimulus of the war booms, if the price at Hankow were to stay somewhere about $900 (Mexican) per ton, half of what it was at its height, thus enabling the utilization of ores from the hinterlands of the provinces; and even under the present ruling of prices and the closing of the less favored smelters, the production of regulus should not be less than 12,000 tons per year.

Jan 1, 1919

By Charles Colcock Jones

In any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly not due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul. "Ore Supply Edwin C. Eckel, in his monumental work on Iron Ores, has but little to say concerning the Pacific Coast deposits. He mentions (p. 269) those of Minaret, Madera County, and the Eagle Mountains, Riverside County, Cal., "perhaps 50 to 100 million tons each;" the deposits in Shasta County, worked for the electric furnace on Pitt River; and

Jan 1, 1916

By G. L. Kothny

Developments of well-surveying instruments, coring .and core orientation, were in an advanced state when drilling for oil began—these developments actually originated with the mining industry.' Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3O. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. Types of Surveying Instruments The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1949

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929

By C. D. Looker

Common salt is mentioned in the most ancient writings as an important article of diet. It is fairly certain that it was used by men and animals long before the dawn of civilization. Its presence in natural springs has often been the determining factor in colonization; wars have been fought for possession of salt deposits; trade routes have been established expressly for the purpose of traffic in salt. Naturally this led men into adventures and discoveries that altered history and advanced civilization. In the early days the uses for salt were few and the methods of manufacture were crude and the purity low when compared to salt of the present day. Then the salt came largely from springs, shallow wells or the ocean, while today deep wells must be drilled to the natural brines or beds of rock salt and spacious shafts sunk so that the ancient deposits may be made to yield their supply of stored mineral. Mining and Purification The quantity of available salt seems inexhaustible. It occurs in practically every country of the globe. About 20 million tons is produced and consumed annually in the world. Of this amount about 7 million tons is produced in the United States; 13/4 million tons of rock salt, 2 1/4 million tons as evaporated salt and 31/2 million tons in brine used in the chemical industry. Mined rock salt is used in its natural state without purification. It is classified for the trade by crushing and screening. The average purity of rock salt mined in the United States is about 98.3 per cent pure sodium chloride1. The usual impurities are gypsiferous shale, anhydrite and silica, with traces of potassium, magnesium and calcium compounds. Refined or evaporated salt is made by crystallizing the salt from brine in open pans or vacuum pans. A comparatively small amount of salt is made from ocean water or the brines of inland lakes or seas, sometimes by solar evaporation. By far the larger amount of brine is obtained by drill-

Jan 1, 1938

By Ian Wark

SODIUM sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators' claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1936

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938

By H. H. Stoek

A study of Americarf coal-mine practice shows two of its distinctive features to be: A greater number of accidents per thousand employees than in any of the other leading coal-producing countries; a much greater percentage of the coal lost than in any of the other leading coal-producing countries. Although our subject is mainly concerned with the second feature, any consideration of mining methods should include safety, efficiency, and economy or costs. If the argument could be offered that our wasteful mining was necessary on account of safety, and that it is carried out with less loss of life than in other countries, the plea for conservation of coal could not he so strongly urged. But when we are wasteful of both life and property, the subject merits more: consideration than it has received. Some coal operators will doubtless say that the unit of accidents should be the number per million tons produced rather than per thousand employees, for by adopting this unit America probably stands in the lead rather than the lowest among the countries. However, vital statistics are not usually so expressed by other governments, by life and accident insurance companies, or in other industries, and it is merely begging the question and attempting to bolster up a bad condition to adopt a peculiar unit for the statement of our accidents. For many years the statement was made by various agencies, and was unchallenged, that "For every ton of bituminous coal mined in the United States a ton had been lost in the way of pillars left in the mines." This statement was undoubtedly true for many years, and although in the past decade some progress has been made toward obtaining a higher extraction, and in some districts very decided progress, the loss is still great; and, although no exact data can be given, it is probable that for the United States as a whole at least one ton is lost for every two mined.

Jan 1, 1923

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By L. E. Porter

El Segundo field is about 14 miles southwest of the central portion of the city of Los Angeles, immediately adjacent to the town of El Segundo and the Standard Oil Company's El Segundo refinery site. The field is served and bisected by several major highways connecting the beach cities on the west side of the Los Angeles Basin. The exact location of the field and its position with respect to other producing areas is shown on the map covering this portion of the Basin (Fig. I). The Republic Petroleum Co. discovered the first commercial production in the area when it completed its El Segundo No. 1 (sec. 18, T. 3 S. R. 14 W.) at a depth of 7402 ft. on Aug. 24, 1935, flowing at the rate of about 400 bbl. per day, 28" gravity oil. The producing horizon in this well consists of about 72 ft. of conglomerate and schist conglomerate situated below the nodular shale (Miocene). The true (or solid) schist (Franciscan) was encountered and penetrated some 20 ft. in the bottom of the hole. This paper gives a report on the history of development and oil production to date, and also submits the writer's interpretation of structural conditions as determined from such development. The limited development, together with the complex and variable nature of the producing horizon, makes any interpretation of the structure at present only tentative, and any forecast for a given well extremely hazardous. History of Oil and Gas Production The El Segundo field has produced approximately 1,920,000 bbl. of oil. It has 27 producing wells and 14 drilling wells or locations. The present daily rate of production is about 13,400 bbl. The production history of the field to date is shown in Table 1. The principal companies operating or owning leases in this field are: Caminol Company, Geo. F. Getty, Inc., Ohio Oil Co., Republic Petroleum Co., Pacific Western Oil Corporation, Royalty Service Corporation, Richfield Oil Corporation, Standard Oil Company of California, The Texas Company, Union Oil Company.

Jan 1, 1938

By R. A. Flinn, John T. Norton

A considerable number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping capacity,'' might be a useful indicator of structural changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction or mechanical hysteresis occupies such a position, and, although it is not well understood in terms of basic metallic theory, an observation of its changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention. The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail. Methods of Measuring Damping Capacity Many kinds of observations can be made upon a specimen subjected to a cyclic stress from which can be calculated the energy absorbed in

Jan 1, 1938

By C. W. Davis, R. S. Dean

The purification of iron ores by means of hand magnets dates back more than 100 years. The first record in the United States Patent Office of a machine for the magnetic separation of ores shows that on Feb. 20, 1849, U.S. Patent 6121 was issued to Ransom Cook for improvement in electromagnetic ore separators. The patent covered the use of a revolving cylinder, or drum, with poles of electromagnets in its periphery for the purpose of separating magnetic oxide of iron from substances with which it might be associated, by causing the electrornagnets when revolving as component parts of the cylinder to be successively charged to take up the ore and discharged to part with it. Since this patent was issued the science and technique of magnetism have advanced more than most other fields of endeavor. The development of electrical machinery has required and obtained better and better magnetic materials, and the science of applied magnetism is as completely and satisfactorily developed as any branch of physics. Nevertheless, the patent of Ransom Cook, issued in 1849, comes close to covering everything that is now being applied in magnetic separation. The cynic may conclude that this proves the uselessness of modern science and may point in confirmation to flotation, which has grown in a few years, practically without benefit of science, to be the most versatile and useful of concentration methods. On more careful study, however, it appears that an accurate determination of the magnetic properties of minerals and their amenability to control by mechanical and heat treatments has not heretofore been made. The first essential, therefore, in the design of improved magnetic separators has been missing. In spite of this hiatus in scientific data inventors have been busy, and patents are on file covering mineral separations by means of nearly all known magneto-mechanical effects. Because of a lack of knowledge of mineral properties, most of these inventions never worked well enough to find commercial use. The Metallurgical Division

Jan 1, 1935

By E. R. Borcherdt

RECENT years have seen great progress in drilling practices. The partial change from heavy drills and stopers to lightweight airleg machines has had great impact on stoping and drifting methods. The change was sparked, of course, when the Germans applied tungsten carbide to drill bits during World War II. This invention made it possible to drill nearly cylindrical blastholes, with a very mini- mum of drill steel changes, so that small fast-cutting bits* could be used without sacrifice of powder-loading density at the bottom of the hole. This is one of the few instances of increased efficiency through reduction in size. Usually the opposite is true. Application of these lightweight drills and small bits has lessened the vibratory stresses set up in the drill steel rod, and rod breakage has been greatly reduced. During the past several years phenomenal reduction in drill steel breakage has resulted from the use of carburized rods. These rods are now supplied by several manufacturers, with carburization of both the exterior and interior surfaces of the hollow drill steel. The rods are heat-treated over their entire length after the completion of bit connections, collars, or lugs (in the case of 7/8 Hex and round steel). This eliminates breakage from the usual metallurgical notch existing in conventional rods-there are instances of more than 2000 ft of drilling in hard ground before breakage. Steel rod failure results from fatigue checks, at right angles to the rod axis, progressing to a point where parting or breaking of the rod occurs. There are many of these checks in a used rod. Only the most advanced check causes the break, but with a small additional amount of drilling another check advances to the breakage point, and most of the value of reconditioning is lost. Since the development of carburized rods, the practice of discarding drill rods after the first break may be economically justified.

Jan 4, 1957

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) IN the case of The Eureka Consolidated Mining Company v. The Richmond Mining Company of Nevada, recently tried at San Francisco, California, the real defendant was the Richmond Consolidated Mining Company, of London; but this being a foreign corporation, holds its mining property in Nevada through the Nevada corporation of similar name, in which the London Company owns all the stock, except the few shares necessary to "qualify" the American directors. The trial would naturally have taken place in the Circuit Court at Carson City, Nevada, and before a jury. But by stipulation of the parties, the case was tried in San Francisco, before Hon. Stephen J. Field, Justice of the Supreme Court of the United States, Hon. Lorenzo Sawyer, United States Circuit Judge of the Ninth Circuit, and Hon. E. W. Hillyer, United States District Judge, for the District of Nevada. The hearing began July 23d, 1877. The witnesses occupied two weeks, and the argument of. counsel three days. Very eminent lawyers were. engaged on both sides ; for the plaintiff, Messrs. Solomon Heydenfeldt, R. S. Mesick, John Garber, and H. J. Thornton ; for the defendant, Messrs. S. M. Wilson, Thomas Wren, and J. J. Williams. The court held the case under advisement until August 22d, when Mr. Justice Field delivered its unanimous opinion in favor of the plaintiff. The action was a complaint in ejectment, and an appeal was taken to the United States Supreme Court. The questions at issue between the Eureka and the Richmond Company in this suit, comprised several points in the construction of the mining law of the United States, and its relation to the customs and regulations of the mining districts, which possess an importance and an applicability far beyond the limits of the case in which they arose. It is my purpose to state these points, the arguments

Jan 1, 1878