Search Documents

By R. J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker's shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By John Mathews

IT is a great honor to be asked by. the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid-to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe, was of brief duration-only one year-and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the, steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher-Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "austenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his -laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I .worked side by side with William Campbell

Jan 4, 1925

By L. L. Wyman

IN order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess hinder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350° C.

Jan 1, 1930

By John A. Mathews

It is a great honor to be asked by the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe was of brief duration—only one year—and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher— Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "aus-tenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I worked side by side with William Campbell

Jan 1, 1925

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By A. Martens

When I was honored with an invitation from the American Institute of Mining Engineers to present a paper at the Chicago meeting on the microstructure of iron, I hesitated about accepting, as the short interval that would remain at my disposal, after other pressing matters had received attention, could not but seriously affect the work of preparing such a paper. Unfortunately my fears have been realized and my work is neither completed, nor yet as comprehensive as I should desire. Mindful of my promise, however, and recognizing that 1 have reached a point where the results of my researches may prove suggestive, I am led to present them now, trusting that this brief explanation map secure indulgence for whatever deficiencies the paper may disclose. So far as my knowledge of published memoirs and treatises extends, microscopy cannot yet be said to possess a really firm foundation. In few cases only has any systematic development of the methods of investigation been undertaken, and broad gaps remain to be filled. It is not yet possible, therefore, to give a complete survey of the field, or, indeed, to supply a text-book on microscopic metallography. As Mr. F. Osmond, of Paris, a distinguished member of our profession, has undertaken to prepare for the Chicago meeting a historic review of the work actually accomplished I need not touch on that branch of the subject; but before entering upon my special theme, it may not be out of place for me to introduce certain explanations, as furnishing reasons for the course 1 have hitherto pursued, and to offer some suggestions for the further development of the methods of microscopic investigation. In microscopic metallography, the examination has to be conducted principally with incident light. Objectives of low power, in which the distance between the front lens and the abject is considerable, are adapted for directly incident light, and in such cases the relatively great depth of the image renders it possible to examine

Jan 1, 1894

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By T. A. Wilson

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.2 The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been clone on single-crystal zinc, but as it 'is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips3 have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1927

By Frederick Laist

ABOUT six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electro-negative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection-1 mg. or less per liter.

Jan 10, 1920

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By W. R. Crane

The support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact, the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident, then, that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 1, 1925

By C. H. Mathewson

MicrOscopic metallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent rnicrostructural rnosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientatjions and it is always possible to derive one from the other by some form of- rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By L. L. Wyman

THE exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics, 1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors" wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickel-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-1 per degree Centi-grade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working can cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carbon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys.

Jan 1, 1939

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By C. H. Mathewson

MICROSCOPIC rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atomis or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929